Changed BIOS Now Will Not Boot Windows 7 Ultimate?
Dec 19, 2012
Yesterday I was attempting to wipe my hard drive as I was putting my laptop for sale. Whilst it was wiping my laptop crashed and would not re boot properly but I was able to access the BIOS . I stupidly changed some settings following some advice on a forum I now cannot find and when I tried to re boot it stays on the philips page for around 10 minutes. None of the keys work, like F12, F2 ect. After ten minutes it give me a screen thats says 1.Insert your Windows installation disc and restart the computer.2.Choose your language settings, and then click "Next".3.Click "Repair your computer."If you do not have this disc, contact your system administrator or computer manufacturer for assistance.Status: 0xc000000fThis is how I understand it as my system is in Polish and Polish is not my first language and with technical language I am not fluent and I beleive thats how I made the mistake in the first place in the BIOS.
View 9 Replies
ADVERTISEMENT
Jul 19, 2012
I changed the boot drive in the BIOS to a new drive. I thought it worked but when I check Disk Managment in Windows 7 it still shows the old drive as the boot drive. Is there something I have to do in Windows to finalize the change?
View 3 Replies
View Related
Jul 19, 2012
I changed the boot drive in the BIOS to a new drive. I thought it worked but when I check Disk Managment in Windows 7 it still shows the old drive as the boot drive. Is there something I have to do in Windows to finalize the change?
View 1 Replies
View Related
Oct 28, 2012
I have a desktop using a Gigabyte GA-Z68X-UD3H-B3 (revision 1) motherboard. Using the Gigabyte @Bios utility, I updated the Bios to F12. After rebooting as @Bios suggested, I can no longer get Windows to boot. I've noted the following:
1) I have issue accesing the Bios setup. Sometimes I can access it, sometimes I cannot;
2) When I am able to access the Bios, I can confirm the disk Boot Priority, however it's is now showing the drives as SCSI (I only have SATA drives);
3) There is a new setup screen displayed after the Gigabyte logo screen shows. This screen now shows 'Serial ATA AHCI, Version iSrc 1.20E.
Copyright (c) 2003-2008. Intel Corporation.
**This version supports only Hard Disk and CDROM drives. **
Please wait. This will take a few seconds.
Then shows Controller/Bus/Function/Port/Device and lists all harddrives. At the end of the drive list it shows 'AHCI Bios installed'
4. After step 3, it shows the prompt 'Loading Operating System' - the boot hangs at this point.I DID backup the existing Bios before updating it. I have not gone in and copied that file to a floppy to try and flash the Bios using the backup (don't know if this is possible).
View 3 Replies
View Related
Feb 8, 2013
I was running Windows 7 ultimate x64 on my system (specs below), and I usually let my computer go into hibernate as it does that automatically after some time of system inactivity. Usually it will boot back up with no problem but then last week I tried to boot it up, it crashed and said system error.. I can't remember everything it said as it was obviously coded; since then I haven't been able to bring up the same warning screens.
Instead what happened was I reinstalled windows 7 on the same drive, formatted and all, and after installation it would finalize my settings, etc. After which, it would do a final reboot and, after bios goes, the computer hangs on a command prompt type screen with just a flashing underscore. Asking my family members, they proposed it might be a hardware issue so I bought a new hard drive (Seagate Barracuda 1tb.. not sure if that matters) and tried installing windows on that drive; same exact problem.
I also tried different combinations of RAM with my board, including just one stick of RAM, tried taking out the video card, tried taking out the sound card, etc. No dice. So my dad took his drive from his computer, that has an install of VISTA x64, and I plugged it into my computer and it worked perfectly. Conversely, I plugged my drive with the Windows 7 install into his computer and it also worked perfectly. We tried playing around with a few settings in the BIOS, etc. but nothing gives.
SPECS:
MOBO: Intel DP45SG
Chip: Q6600
Ram: Hynix 2x2gb and 2x1gb kingston
Vid card: Zotac GeForce GT 610
Sound: Creative X-Fi Xtremegamer
BIOS: Should be up-to-date, irregardless it ran Windows 7 before
View 1 Replies
View Related
Aug 19, 2010
I have been incredibly stupid and changed the settings in my BIOS setup. What is even more stupid is I did this by making it "Load Optimal Defaults" so I dont actually know what has been changed.As a result of this windows 7 now cannot start, it brings you to the error fixing part where it searches for errors, cant find any and offers you some more options including system restore. Ive done a system restore but that has also not fixed it. I have little idea how to fix this, windows 7 was working perfectly until I changed the BIOS, but not knowing what was changed means I cant change it back.The BIOS version is: 4core1600twins-p35 p1.40.
View 4 Replies
View Related
Jul 25, 2010
I used to have Vista basic installed on my Medion Intel Core 2 Duo machine but then gave Ubuntu 10.04 (Lucid Lynx) a try.After buying Win 7 Ultimate I want to install it and erase Ubuntu (mainly because of poor support for Tascam audio/midi interfaces). I do not want to install them side by side and then erase Ubuntu as I want to avoid the Fix MBR issue.After inserting the installer DVD I get the usual message "Click any key to boot from CD" but pressing keys on my USB keyboard or mouse does not appear to do anything. I have tried various keyboards including serial port devices but the result is always the same.Has Ubuntu changed anything in the BIOS or else how can I solve this problem of not being able to use the keyboard when trying to boot?
View 6 Replies
View Related
May 28, 2012
i changed a Bios setting on my Toshiba Satellite Pro L640 now my laptop won't post and keep going to the internal recovery utility?.
View 4 Replies
View Related
Sep 18, 2011
my computer was getting too hot i went into the BIOS and changed a few things like turning off the auto-controlled fan sensors, FSB i put down to 200 and the CPU voltage I changed to 1.0Volts. I started up windows again. This time though, the option for "hibernate" had disappeared. So i looked up how to put it back on. and changed the power settings to "never" allow "hybrid sleep". So now i have the option to hibernate again. But the strange part was this. When I put my computer to sleep now. It apparently shuts down fully. (no more blinking light) then i turn it on and it re awakes from sleep. It's actually nice to have it this way. I tested it to see if i could disconnect the power fully and then still restore it back from sleep. Sure enough it lets me disconnect the power for up to 5 seconds then i plug it back in and it will still restore back from sleep. I guess my question is. Is the computer using even less power now to keep the information on the RAM. I read somewhere that on average your computer uses about 6 watts while in sleep mode.
View 2 Replies
View Related
Aug 25, 2012
so i did a bios update, and it wont boot after the update.its a asus m4a79xtd evo (rev 1.01g)i dont have a backup of the bios
View 3 Replies
View Related
Oct 29, 2012
I was working on setting up a PC for network usage with the understanding that it hadn't been used muchpreviously.Unfortunately I found that it had a PC name already existing on the network and went to change the PC name and IP address as needed for a static IP environmentHowever, after selecting to "restart" the system never rebooted up and I cannot seem to access the CD drive to place a restore CD or basically do anything with the PC.Any ideas on what happened?I've unplugged the computer and waited a few seconds to plug it in.Once replugged it returns to having the basic lights on it blink about once every few second and appears to be otherwise disabled.
View 1 Replies
View Related
Apr 4, 2012
just installed an asusM5A97 mobo. hdd and everything else stayed the same. problem is, it will only make it to boot screen no matter what. i tried repair and open normally but it still will not let windows boot.
View 4 Replies
View Related
Jul 10, 2012
I recently built my computer and installed a ssd and a hdd, the OS is on the ssd which is the c drive but since it is smaller than the hdd I tried to change the letters around and make the hdd the c drive using regedit because the default install location seems to be the c drive and after restarting the computer it boots up and says preparing your desktop then goes to a blue screen with just the cursor. I tried booting in safe mode and all I get there is a black screen also
View 9 Replies
View Related
Apr 23, 2012
I spilt some water on my laptop a few days ago but fortunately it's completely dried out and working perfectly.... apart from this minor (but important) issue.
Problem: the system time does not stay correct. Even after manually updating the BIOS time and also even after manually syncing it with the various servers available under the time options.
Fix: set the internet time sync interval to every minute rather than its default setting? How do I do this?
P.S. This couldn't be a CMOS battery issue surely because even when the system is on and plugged in the system time still deviates from correct. (I assume the CMOS battery is only used when the system is powered off.) If I need it replaced, how does that sit with my Dell hardware warranty?
View 9 Replies
View Related
Jan 14, 2012
I am trying to install a password recovery cd on laptop. I changed the order in bios but still not giving option too boot from cd. I even logged in as a guest and put an audio cd in .It didnt give option too play. I think its the cd drive. What can I do?
View 1 Replies
View Related
Apr 9, 2011
I needed a good backup program so I downloaded a trial of MirrorFolders. I have two identical 750GB drives in my laptop: C (my main drive) and Z (my backup drive). MirrorFolders made an identical copy of C onto Z. That wasn't what I really wanted, because C is partitioned into D and E, and MirrorFolders didn't mirror the other two partitions. The backup methodology wasn't exactly what I was looking for, so I uninstalled the program. After uninstalling MirrorFolders, the machine is now booting to the Z drive, which means I can't format it and try another backup program.
Is there a simple way to restore the boot ability of my C drive? I read a great deal about copying boot folders and such, but I wasn't exactly sure if these were the right answers and I didn't want to screw things up any worse. I figured I could go into the BIOS and disable the Z drive, but no luck. The machine couldn't find a bootable drive, even though C supposedly has the same files as Z.
View 9 Replies
View Related
Dec 19, 2012
Spy hunter was installed and never fully installed. I removed from system but, when I startup the pc i get messeage fdisk cant find dev.sda no medium found.
View 1 Replies
View Related
Dec 14, 2011
I just installed a new motherboard, CPU, memory, and video card into my computer. I'm not looking to salvage my old OS install, and have all important data backed up, so I planned to just put the hardware in and boot off my windows disk to do a format and reload. However no matter what I do I can't get windows setup or an OS to load. When loading the installer it locks up at the windows splash screen. I've tried booting off the hdd and it does the same thing. I tried it in safe mode and it locks up before it finished loading all the files. I also tried booting mini XP off my Hirens 15 disk and that locks up at the splash screen too.
So at this point I ran memtest to see if it was my ram causing problems but it all tested ok. how to boot off my disk so I can format and reload?
View 9 Replies
View Related
Apr 3, 2012
I'm not sure what the trigger was but my C drive where my os is installed apparently took the drive letter of an external drive that I use for backup. It is now the X drive and I cannot boot. I do get the repair screen but cannot repair as there is no operating system to choose. Booting from windows disk makes no difference here.My bios (uefi) can see the disk, I can also see it from the command prompt?
View 4 Replies
View Related
Apr 9, 2011
On my Windows 7 at the bottom left it shows:Test Mode,Windows 7,Build 9780,Also I changed the boot screen but I can't now change it back to the default, I tried using the command prompt but didn't work.
View 1 Replies
View Related
Jan 22, 2013
I recently ran a memtest86 program to check my ram so I had to change my boot priority to get the program to work. Now it seems I cant change it back. I've changed it and saved it but my cdrom still wants to boot up first. I even reset the bios with no luck.
View 9 Replies
View Related
Oct 26, 2009
I am choosing which OS to boot by changing the boot order in my BIOS. To me, this seems clean and simple. I built 32 bit XP on one disk, then removed that disk from my system, installed a different disk, and built 64 bit Windows 7.
When both disks are installed, I change the boot order to select the OS I want, and each OS sees and can use the files on either disk.
Am I asking for trouble here, or is this as clean as I think it is? What I want is one set of user document files which can be used from whichever OS has been booted.
View 2 Replies
View Related
Jun 6, 2011
All I did was open a video strored locally with no connection to the internet. Shut down computer properly. I go to start it up and start up repair kick in. I have let the thing run on startup repair over night and a total of 12 straight hours. It reboots once, maybe even twice. Then it just sit a says attempting repairs. I just did a hard shut done. I was able to pull the data off using Uburba (not sure of the spelling). The USB 2.0 is not recognized in start up repair command prompt. I had a image saved to a CD. I can't get past the username password. The one I had wrote down does not work. System restore fails because I can't it doesn't have a .DDL file or it says something. If I could get the USB 2.0 to work I have an external that has a couple of images that would be better than re-installing. I tried moving the image into the computer then using the image restore, but I learned that doesn't work because it somehow tracks were it wrote the image to. This is way I need the usb 2.0 to pull the image from my external HD.What is the default password of HomeGroupUser$?
View 3 Replies
View Related
Nov 10, 2009
I have windows XP pro 32 bit installed in C drive and then installed clean win 7 64bit in drive D. Everything works properly but when I boot from XP, it is in C drive and I see Windows 7 in D drive, when I boot from Windows 7, I see win 7 in C and winXP in D drive. Is it normal or is there any I can do to fix win Xp in C and Windows 7 in D?
View 3 Replies
View Related
Jul 5, 2012
I have a Lenovo ThinkPad X60 laptop with Win7 32-bit Ultimate and an SSD (I know, I know, just go with it. I'm building a desktop soon). I could list the specs, but that's useless for this problem (I'd think).
At times (not always), when either resuming from hibernate or booting up from a shut down, the computer generally freezes at the point right after the BIOS screen. So it's just a black screen. This is before the window that says "starting up" (literally a window... the Windows logo). Whenever it freezes, it NEVER goes to the boot screen of Windows. I'm assuming this is an error with the hard drive, since the OS is on the SSD and the boot screen is from the mobo. However, this only started happening after a rather heavy fall to the ground that cracked many parts of the plastic shell on the computer. It still works occasionally when I can get it to boot up (nothing different when it boots up... same settings and everything. Spontaneous).
I have tried:
1) Cold reboot
2) Removing battery
3) Going off only battery
4) Unplugging EVERYTHING from the computer
I have not tried chkdsk yet. Is it necessary? Also, would there be a log somewhere of what happened? It never booted into Windows.
View 4 Replies
View Related
Apr 4, 2011
We just build a new system to play around with the Intel Rapid Matrix RAID
Asus P8P67 MB + 8GB RAM+ I5 2500K + 2xWD BLUE HD SATA 6 IN SATA 0 and SATA 1 ( SETUP AS RAID Mirror)We install the Window Ultimate 64 Bit in the RAID Drive .... No problem after all the drive install We also allocate 50GB for doing a image backup (Drive F) We restart the system and goto BIOS to set the HD from RAID to AHCI ( This is the situation happen when the BIOS reset)
Supprise me the system can boot form the Drive ...... (In Device Manager .... I see two WD 1TB HD instead of one 1TB RAID Drive) But when I use Disk Manager it takes really long time to run... I can't wait for that long and shut down) On My computer I only see one HD with 4 Partitation ...
I restart the system and Goto the BIOS to reset back to RAID...and it give error..
I but the W7 Ultimate Boot disk to repair but no success.. Try to load the Backup Image .... cannot find it...
From the old time .... if the BIOS reset it will set to IDE Mode ... Then I am'not able to login to window it will come up blue screen and I just reset to RAID it will fine.... But nowadays... the New MB set Default AS AHCI...then I encounter this issue.... Lucky ... we just testing the new system now..
If I have a cooperate customer want to setup a RAID drive and suddenly Power Cut Down.... BIOS reset..
View 1 Replies
View Related
Nov 16, 2011
Windows 7 ultimate 32 bit suddenly switched off, reboot does not show on screen which reads "HDMI CHECK SIGNAL CABLE". Using ATI HD4350 fanless with heatsink connected via HDMI lead. tried another monitor using white dvi cable monitor stays blank then shows power saving mode. So that eliminates the monitor & hdmi lead. Could a duff graphics card show this error? No on board graphics. Unable to get into bios no bleeps, Windows 7 dvd no good either, all fans come on and motherboard MSI X58 on board indicator light goes from amber to green when pc turn on so m/b must be ok.
View 7 Replies
View Related
Aug 6, 2012
In the chaos of moving to a new house yesterday, a box my friend was moving ripped and a bottle of beer smashed onto my open and powered on laptop, scattering both liquid and glass everywhere. We immediately powered down and removed the battery, and placed the laptop upside down and mopped up the excess liquid from the outside as much as possible, and set it to dry upside down on a towel.My laptop is a Lenovo U330, I had my brother install Windows 7 on it for me last year, but he kept the disks so I don't have any of them.Several hours & some blowdrying later, we attempted to start up the laptop (I would have preferred to wait longer, but I needed to know if mine would work in case I needed to borrow my friend's for the week). The laptop will load the lenovo startup screen, and then flash the windows loadings screen (with the option to press f2 or f12) for a few seconds before recommending that I run startup repair. Which if I select it, will freeze after a few seconds. Usually my laptop's pretty noisy, but while the battery light flashes as if there is activity going on, there's no noise coming from it at all.
View 7 Replies
View Related
Jan 21, 2009
First off, Windows 7 is very cool; I might use it more than vista now that I got internet for it, but that will have to wait for a month or two. My first question is: when I boot up my comp, and I have to pick either vista or Windows 7 (I have Windows 7 on another partition), I usually leave the room while my comp is booting, so after 30 seconds the BIOS picks Windows 7 as the default OS because its first. I would really like to boot up my pc while doing something else, and I would love for the BIOS to pick Vista after 30 seconds instead of Windows 7 because I use Vista for games and such. Is there some way of doing that or do I have to sit around throughout the start up and manually pick Vista?
My second question seems a little picky or over the edge, but when I boot up my comp and have to pick an OS, it prints "Windows 7" while underneath it it prints out "Microsoft Windows Vista". Is there some way to add 'Microsoft' in front of Windows 7 when Im picking in the BIOS? It doesn't look as good without the Microsoft.
View 9 Replies
View Related
Dec 25, 2011
Sometime when i turn on the PC , all fans are running but nothing boot up no beep sound either. I have to push and hold on power butt to utrn it off then turn it on again couple time to get it to boot up but then it freez up in few min!I have try to boot in bios mode but get same problem it freez!!! when i try to do memories test it tell me i have hardware problem and again it ran memories test for 2 min then free
View 6 Replies
View Related
Oct 22, 2011
Hall drivers/updates for my new build are complete, and when i boot, the first asus bios screen comes up, then displays components (as usual), but then goes back to the first start up bios screen. This cycle happens three times before "starting windows" comes up (i have windows 7 ultimate 64-bit). I have a OCZ vertex 3 60Gb SSD, i5 2500k, asus p8z68-v pro, corsair vengeance 8gb cl8 1600mhz ram, and to get to the windows screen takes 40 seconds. Can anyone explain why it is displaying the bios start up screen three times before 'starting windows?'
View 4 Replies
View Related
