I have been incredibly stupid and changed the settings in my BIOS setup. What is even more stupid is I did this by making it "Load Optimal Defaults" so I dont actually know what has been changed.As a result of this windows 7 now cannot start, it brings you to the error fixing part where it searches for errors, cant find any and offers you some more options including system restore. Ive done a system restore but that has also not fixed it. I have little idea how to fix this, windows 7 was working perfectly until I changed the BIOS, but not knowing what was changed means I cant change it back.The BIOS version is: 4core1600twins-p35 p1.40.
my computer was getting too hot i went into the BIOS and changed a few things like turning off the auto-controlled fan sensors, FSB i put down to 200 and the CPU voltage I changed to 1.0Volts. I started up windows again. This time though, the option for "hibernate" had disappeared. So i looked up how to put it back on. and changed the power settings to "never" allow "hybrid sleep". So now i have the option to hibernate again. But the strange part was this. When I put my computer to sleep now. It apparently shuts down fully. (no more blinking light) then i turn it on and it re awakes from sleep. It's actually nice to have it this way. I tested it to see if i could disconnect the power fully and then still restore it back from sleep. Sure enough it lets me disconnect the power for up to 5 seconds then i plug it back in and it will still restore back from sleep. I guess my question is. Is the computer using even less power now to keep the information on the RAM. I read somewhere that on average your computer uses about 6 watts while in sleep mode.
Yesterday I was attempting to wipe my hard drive as I was putting my laptop for sale. Whilst it was wiping my laptop crashed and would not re boot properly but I was able to access the BIOS . I stupidly changed some settings following some advice on a forum I now cannot find and when I tried to re boot it stays on the philips page for around 10 minutes. None of the keys work, like F12, F2 ect. After ten minutes it give me a screen thats says 1.Insert your Windows installation disc and restart the computer.2.Choose your language settings, and then click "Next".3.Click "Repair your computer."If you do not have this disc, contact your system administrator or computer manufacturer for assistance.Status: 0xc000000fThis is how I understand it as my system is in Polish and Polish is not my first language and with technical language I am not fluent and I beleive thats how I made the mistake in the first place in the BIOS.
I changed the boot drive in the BIOS to a new drive. I thought it worked but when I check Disk Managment in Windows 7 it still shows the old drive as the boot drive. Is there something I have to do in Windows to finalize the change?
I changed the boot drive in the BIOS to a new drive. I thought it worked but when I check Disk Managment in Windows 7 it still shows the old drive as the boot drive. Is there something I have to do in Windows to finalize the change?
I used to have Vista basic installed on my Medion Intel Core 2 Duo machine but then gave Ubuntu 10.04 (Lucid Lynx) a try.After buying Win 7 Ultimate I want to install it and erase Ubuntu (mainly because of poor support for Tascam audio/midi interfaces). I do not want to install them side by side and then erase Ubuntu as I want to avoid the Fix MBR issue.After inserting the installer DVD I get the usual message "Click any key to boot from CD" but pressing keys on my USB keyboard or mouse does not appear to do anything. I have tried various keyboards including serial port devices but the result is always the same.Has Ubuntu changed anything in the BIOS or else how can I solve this problem of not being able to use the keyboard when trying to boot?
i ran the program speedbit video accelerator and ever since then my computer notifies me that my browser settings have been changed. It does it more frequently at times and not so frequent at other times. Iv had another program on my computer for a few months that has run great everyday of the week up until today. Iv always run this program from the desktop shortcut, it has a system check and it always goes good except now when i try and open it from the desktop shortcut the system check looks like what i attached its supposed to have all green check marks. i can run the program now but i have to open it thru my internet explorer. and the desktop icon changed for the programs shortcut.
I recently installed an old game. I'm running Win 7 Pro x64 and the game was for XP. I messed with the compatibility settings and I think something went wrong. The folder icons have changed everywhere but on the desktop. The desktop shows the regular aero styled icons. Everywhere else the folder icons are some dumbed-down picture that looks low tech even for XP. Its bright yellow and has no 3D effects. To make it even more frustrating, it only does this when the view is set to details, list, or small icons, which are the only views I ever use. What button did I push and how can I fix this?
At my company I setup and deploy many windows 7 machines. I use a start-up batch file to do most of the work and a few other files in the start-up folder, this is all imaged to the hard drive with a hard drive duplicator. The batch file runs once and deletes it self. Anyways, that is the general idea of what is going on. the only thing left that I have to do manually is change the BIOS settings, USB enabled/disabled, behavior on power up, BIOS password, ect... Is there any way I could automate this process, preferably a command line?
I have a few portable programs on my computer. How do I update them without losing any settings etc. that I have changed? Do I move ".ini files" and/or ".cfg files" and/or "whatever" out of the old version of the program and into the new?
My Acer Aspire one D257 will not restore. Error code is 0x8007191. All desktop icons when clicked go to "notepad" and "notepad" showing for everything to the left except for internet explorer. I have tried restore 6 times but it just comes back with. Bottom right hand icons still normal...files can be accessed through start docs. pics, etc. I have backed up to a remote drive all files for safety but just cannot get system or files to restore.System restore did not complete successfully. Your computors files and settings were not changed.Details System restore failed while restoring the registry from the restore point. An unspecified error occurred during System Restore (0x80071a91) The error code has just changed to the above.
I just accidentally changed my settings on my grapics card so that I can no longer see my desktop on the monitor connected to my HTPC. My HTPC has a monitor attached to it and it also has an HDMI out from the graphics card going to an LED TV in another room. I accidentally switched it so that the desktop can only be seen on the other TV in the other room.
All I can see on the monitor is the blank Windows 7 logo (no desktop icons) and I cannot navigate back to my AMD control page to undo this. I tried rebooting but this does not work. This is an issue as I don't have a bluetooth keyboard/mouse that I can use in the other room to control the desktop. How do I reset this? I am using a AMD HD 6750 graphics card.
When i got home today didn't my computer work, my girlfriend has been the last one using it. So don't know how things were just before the shutdown or anything.when i turn on the computer i get to the screen where "touch bios" is and where i can see the options like Bios settings, boot menu, xpress recovery.but i cant press anything, and after about two seconds on that screen the PC shuts down again.The keyword lights up so there is a responds on it, but just doesn't work to press anything before it shuts down.I've got BSOD upto several times a day for a few months time.believe that my computer is affected by some virus or something is delaying my computer. might be an combination of several things.I got no external things hugged up to the stationeer computer right now.it is a windows 7 x64 machine. usually when i get issues i can access advanced boot up or bios, but can neither in this case..I wonder if it might be a hardware issue.
Mine is gigabyte g31 mother board it is taking too long time to install windows 7 or 8 into it , it will asks press any key to boot from CD\DVD and i pressed after that ,it will start loading windows files and logo will appear and it takes more than 3 minutes to show install windows and also after that it takes 3 minutes to show setup is starting up.
I have a Compaq 6530b laptop and am running Windows 7 Home Premium 32bit. I want to enable bluetooth on the laptop, but the Device Manager says it is disabled in the BIOS and to activate it with F10 on boot.. the problem is it asks for a BIOS password and I keep guessing and cant figure out what it is! Is there a simple way to reset the BIOS password or crack it? I took out the CMOS battery and waited 10 minutes, but that didnt do anything.
I am getting ready to set up a RAID Array but this is my first time doing anything with RAID. I know how to get into the BIOS and change settings and I know with two hard drives, I should do RAID 1. However, I just have a few questions before I do this. First off, I am an idiot and did not notice that my first hard drive I got when I built the computer has a 32 MB Cache:
Caviar Blue 1TB 7,200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive WD10EALX - OEM
I noticed it only had a 32 MB CACHE when I went to get another one. I then asked for the version with a 64 MB CACHE (WD1002FAEX), paid for it and left. Will these two hard drives work together in RAID if they have different sized caches?
I am trying to update the BIOS of my 'ASrock Z68 Extreme4 Gen3' from v1.00 to v1.20. I am running Windows 7 64bit Ultimate. I got the BIOS file from: [URL]. It did not register the BIOS file I had put on my USB drive when going to my BIOS settings. There is an "Instant Flash" function in there. I have tried to make a bootable USB-drive to do it directly from DOS, but my drive can't be formatted as an MS-DOS boot drive. I have tried using HP DriveKey which seemed to work as intended, but it didn't work, the drive was still not recognized in bios. Do you think it's my drive? I don't have another drive with me right now to try it out. I know this is a not really a Windows 7 issue, but I couldn't find a proper category.
I spilt some water on my laptop a few days ago but fortunately it's completely dried out and working perfectly.... apart from this minor (but important) issue.
Problem: the system time does not stay correct. Even after manually updating the BIOS time and also even after manually syncing it with the various servers available under the time options.
Fix: set the internet time sync interval to every minute rather than its default setting? How do I do this?
P.S. This couldn't be a CMOS battery issue surely because even when the system is on and plugged in the system time still deviates from correct. (I assume the CMOS battery is only used when the system is powered off.) If I need it replaced, how does that sit with my Dell hardware warranty?
I have a problem with the entries in the start menu. Normaly I have Swedish which is what the system is set to use. But for some reason the entries in the start menu is english now!How can I change that back? Maybe it hapened when I installed and run the program "Advanced System Care" which was suposed to be a good program, but I'm not sure. I didn't help to uninstall it by the way.
I just flashed my bios before trying to OC my new RAM and, as said, now Windows 7 won't start. Bios update seems successful, I can access it and the new version is written.
I'm guessing clean install but looking for some idea before that.
i5 2500k on Gigabyte P67-UD3 if it's any help. The bios update was from F3 to F7.
I recently ran into frustration trying to save or make new any files in the root C: directory, with Windows7 Home Premium being set by default, of course, to not allow this. I did a cursory skim of some information online about changing these settings, and made some changes a bit hastily. Specifically, for the C: drive I took ownership of every subdirectory and gave my account full permissions under security. Annoyingly, this didn't fix the original issue of saving to that drive (which I no longer care about anyway), and it caused (at least) two new problems. Now my start menu has far fewer listings than it used to have; I imagine some programs were listed in it based on the previous permissions. I tried to do a system recovery, both through the OS and with a recovery disc, and that does not work either. It lists restore points, but after restarting it says that the restore was unable to complete.Can I fix the permissions and ownership of just the restore directory and program components, enough to run one, and revert?Or, failing that, is there a way to undo recent ownership changes made? I poked around in the Event Viewer, but it's not laid out very clearly.It's ok if it's not possible or easy to do it this way; I can grab just my vital files and completely reinstall Windows if it's absolutely necessary, but it seems excessive. I doubt the system restore files are corrupted. More, let's say, confused.Let me know if you need any of the error message codes. Somehow they never seem useful. Screenshots forthcoming.
Is my CPU going bad? Startup error: "Warning! CPU has been changed. Please re-enter CPU settings"It is HomeBuilt, 6years old. ABIT AN8 mobo; Phoenix-Award Bios v6.00PG; Athlon 64 3500+; 4 Gig. Corsair XMS, 400 speed; CoolerMaster 650W PSU; Windows 7 home prem. on 200 Gig Sata HD.I like to shut down every night. Lately, it hangs with this error right after the flash screen of ABIT logo. It gives me the option F1 to continue, Del. to enter setup. If I punch F1, it promptly boots and runs just like always.The same time this showed up, my clock on desktop runs slow. Real Slow.So far I have scanned with MSE, then scanned with MBAM, I pulled the CMOS battery, then moved the CMOS jumper, waited several minutes, then re-set the jumper before I replaced the battery. Oh, yeh, "bout forgot I had a couple of extra hard drive hooked up, one Sata and another Pata, I unplugged both of them, also unplugged my USB flash drive also unplugged USB hub, and unplugged an old USB Zip Drive. I removed all that stuff before I re-set the Bios. Then, of course I reset both the calandar and the correct time.I googled the slow clock and somebody said to go into device manager> IDE ATA/PATA controllers and check the box "enable DMA" on each Channel. I did that.
I installed windows 7 to sony vaio that has xp before and now the bios is not popping up even if press the buttons. The laptop just open window without showing any option key or bios after switching on. What to do I need to boot a program on my usb drive.
1 SATA HDD Primary OS Disk 2x SATA HDD Backup Disks in RAID 1
TO:
1 SATA SSD Primary OS Disk 1 SATA HDD Backup Disk [No RAID]
Everything worked great, no problem. So, since I don't have a RAID array anymore, I decided that I could change my BIOS setting to AHCI instead of RAID. I have a Gigabyte GA-P35-DS3R v1.0 mobo.
These are my steps:Settings > Integrated Peripherals > "SATA RAID/AHCI Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Next Step:Launch BIOS settings Integrated Peripherals > "Onboard SATA/IDE Ctrl Mode" = RAID --> Changed this setting to AHCI Reboot Windows Start screen shows up, but as the color orbs are spinning into focus, BSOD and immediate restart Repeated reboot several times, same outcome Switch both settings back to RAID, reboot, and Windows starts up just fine, no issues.
What am I missing? Why can't I set it to AHCI mode without BSODs?
