Remove Newly Installed Hard Disks Or Hard Drive Controllers / Blue Screen Error
May 19, 2006
A problem has been detected and Windows has been shut down to prevent damage to your computer.If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again follow these steps.Check for viruses on your computer. Remove any newly installed hard disks or hard drive controllers.Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
I recently installed a new Seagate 120 GB hard drive as a slave. I also installed iTunes and am importing songs from my CD collection. Since doing this I am frequently getting a blue screen on Windows XP w/ Service Pack 2. It also seems as though my system is a little sluggish.
having my laptop returned from service I found my Bios messed with where when I would start my computer but Bios wouldn't find my hard drive or an OS I found that my system was set to RAID instead of ATA. After resetting it back to ATA it boots up fine. However I wanted to reformat and start clean.I placed my XP disk in, reset my BIOS to read my optical drive first and no problems.However every time I get to partition drive all I see is "Unknown Device" If I press any key I get a blue screen of death. Most times it's the 0X0000008E.
I did a new hard drive install. When the new HD was complete I thought I would copy the data from the old drive to the new.They both still had os installed They were both connected to the system at the same time.When I finished, I removed the old drive. The new drive wouldn't boot. "Disk boot failure, insert system disk and press enter". After recovery disk completed, the system booted fine. I could reboot from the shutdown option.
The problem I have is when the system is shutdown completely. It requires the system disk again. It will reboot after the system disk is reinstalled. I continually get the "Disk boot failure, insert system disk and press enter" error message.During bootup after a shutdown, I can F2 into the bios before the error message. It will allow me to exit and then windows will boot without the error message.
hey good fellows out there. it seems the problem has struck again.
this is a error message: Error code 0000007a, parameter1 c03dcf3c, parameter2 c000000e, parameter3 f73cf642, parameter4 22808860.
started up then there was the error reporting to settle, so it's a hard disk error, but what exactly is still not known. here's what i was doing just BEFORE this error occured.
1.I have a dell digital jukebox mp3 player that allows for storage of data or music. I tried to copy a 600mb file from the mp3 player onto my hard drive. I had a little over 600 mb of space left on my hard drive (a total storage capacity of 6GB). It said i had run out of space. So i deleted some files, move some things around and i had 1.1 GB of space free for this transfer. i tried again and this time again the message i got was not enough space on drive c:/. So i cancelled out and checked to see what i had on my hard drive, 500mb free!!!?? So i have lost hard drive space and not gain a file...So i investigated and found that i have 1.81 GB of data on c: documents settingsuser. but once i get into user, i have 6 folders none of which display nearly that much data. They are, favorites, start menu, cookies, desktop, my documents, and a file named ntuser. the ntuser file is 1mb, and my desktop has 700 or so mb on it. So my question is how can i get back this lost hd space,
2.Blue screen. Im on xp pro sp1, i use adaware, registry mechanic, and im generally tidy with my windows; note, reinstalling windows did not solve this. I never used to have this issue, but lately when i go to open or close certain programs i jump to blue screen. it references trixdp.dll i think it was, and then "begin physical dump of memory" i must reboot at this point. I use VLC media player, and exiting this program mandates a blue screen. Just now i exited mozilla browser and this was the first time i got blue screen from this program.
I just installed a new hard drive then I installed windows XP SP2 on the disk and the computer keeps rebooting and I'm getting a blue screen c000221 unknown hard error. Then I re-install windows 2000 it works Ok. Then I installed windows XP SP1 it work OK, then I installed the SP2 and the computer started to reboot again. I used drive jujitsu and it was OK. So what is the issue with SP2 and the Maxtor drive anyone knows or has seeing this issue?
I want to downgrade the factory loaded Vista to XP pro on my Acer Aspire M5640 desktop. I found some detailed instructions on line for doing this, but I don't get very far before I get a blue screen error message while the computer is in the process of booting up from the XP disk and loading the files while in windows set-up mode. It reads as follows: "A problem has been detected and windows has been shut down to prevent damage to your computer.
"If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: "Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer. Technical information: STOP: 0x0000007B (0xF78D6524, 0xC0000034, 0x00000000, 0x00000000)
I have a HP pavillion laptop windows xp.I think i got a virus back and tried to remove them with some anti spyware stuff but in the end i tried to reformat and this is what happens. I have my set up disk in, i start up my computer. Blank black screen with blinking _ in the top left corner. After a bit of loading in this screen it says Press any key to boot from CDa blue screen with Windows Setup is in the top right. At the bottom it says "Setup is loading files" etc etc. Text flashes in the space beside.a screen tha tsays "A problem has been detected and windows has been shut down to prevent damage to your computer. If this so and so" I think this is the blue screen "of death"?
I was given an older machine that had win me installed. It was full of junk and would crash often. So I downloaded a startup disk for formating Win-Me. I ran thru the process - formated the hard drive or so it seemed but when I tried to install winxp it would go thru the process and then get a blue screen stop message. When I restarted the machine I got the message "hard drive capable but disabled". There are ways to enable the drive but you need an operating system to do that. The cd rom on this machine is scsi and I am not familiar with that process. Is there a way to enable a hard drive with out the operating system? The drive is an ultra DMA-mode 4.
My computer seems to work fine except when I try to do a copy in Casper XP to backup my hard drive to external HD. I also got this stop code last night when trying to do a disk check to correct errors. Stop 0X0000000A (0X00000188, 0X000000FF, 0X00000000, 0X804E35E9). I have located online page for stop 0X0000000A codes which states could be driver problem... that last one parimeter 4 -- 804E35E9 how/where would I find out which/if this is associated to a particular driver so I can possibly correct it?
When starting my computer, I have started getting a "Hard Drive Not Found" error on the black screen just as the pc starts booting up. I've not written down all the details, but I see the MAC address displayed and a cursor blinks just after the letters DHCP, there is something about "boot filename not received", then "Hard Drive not found" and then it defaults to the Windows boot screen and will boot up fine. The pc seems to run normal once up...but, I'm somewhat concerned about a "Hard Drive Not Found" error. It just doesn't sound good. I'm going to try to get more specifics as to what I'm seeing on the boot screens, but wondered if anyone here might have some suggestions as to what my issue is?
My pc specs should show in my signature. Also, I recently upgraded my graphics card, but that's the only hardware I've been playing with lately. Don't know if that would make any difference because I wasn't getting any trouble until now and that graphics card has been in about a week already.
I have a second hard drive installed on my computer. Lets call this F:My main hard drive, were I am running WXP SP2, Home Ed., and were my program files are kept. Lets Call this drive C:IP3, 733mhz, 384 mb, HOMEMADE. works well, very happy $5.99 OBO.I am filling up C: and have tons of room on F:. Can I put program files on F:, easily that my computer will recognize and be able to use effectivley and effciently? With out jack-ups? Yes I understand that this an imperfect world, but If I could do what I wish within this situation, I will be closer to.
i have use more than 10 disk of windows xp to format compaq pressario v3000.. when i press enter to format.. it shown that the hard drive is not installed. what should i do sir?
In addition to my other posting here, I want to ask you professionals, if it is possible to mirror my existing hard drive onto a much larger hard drive?My partition C became way too small over the years, the Windows XP files have blown up their size. Partition D (which contains all installed programs) is still fine. But I was never able to use software like "Partition Magic" to adjust the space between these two partitions.So I might just have to buy a new hard drive. But I want - I even HAVE - to keep the installed XP the way it is now. Lots of software installed. So I wonder, if there is any way just to "mirror" the existing version of XP onto a new hard drive, and then just to exchange the old hard drive with the new one?
I have a 2nd hard drive installed on my computer and i noticed yesterday that everything on it except for one folder has been deleted everything from my music to my videos. However, when i check the properties of the hard drive it still shows that space is being taken up on that 2nd hard drive as if all my files are still there. I went into my itunes and tried to play the music i have on my 2nd hard drive through itunes and to my surprise it still plays which it shouldn't if the files had in fact been deleted.
installed second hard drive,moved program files from c drive to folder i created in new drive.installed farcry onto new folder.but farcry files where scattered allover & not in folder of its own.uninstalled farcry with program called my uninstaller.pc then froze couldnt get into task manager,so switched off pc.when i restarted,disaster, folder in new drive had gone along with my programs ,mostly games,
Help. I've installed a 2nd hard drive (windows XP). Everything went smoothly, however, when I was prompted to copy all files over to the new drive, I opted not to do so, not realizing that would cause me to not be able to install programs on that drive. Now my new drive is just used for storing music, pictures and movies. Please tell me what I'd need to do so I can install programs on that drive. Thanks
I have been given the above laptop to see if I can do anything with it as there are problems. My problem at the moment is where is the hard drive and how to I remove it to replace?
I've been using an USB enclosure successfully for some time with no problem. I upgraded to a Maxtor 100 gig in the same enclosure. When turned on it does the "plug and play" chimes and it shows up in the device manager as installed and working properly. But it is not shown in My Computer as a drive letter.
Dell dual core, 1 gig RAM, Windows XP service pack 2
just installed a second internal hard drive. tried to access bios at start up (to setup hard drive) but system doesn't respond to ANY keyboard keys. system just continues with normal Windows boot-up. once XP is running all functions and software seem fine. no matter how many times I try at "Press Del to enter Setup" nothing works. Jusat before I had this problem, I had a problem with software (which I have removed) that caused my system to lock up. when I rebooted system stopped and offerred reboot options, ea: Safe Mode, but I the arrow keys would not work, system just went directly to Windows boot up.how can I access the bios if system doesn't respond to keyboard?
I just recently installed a new hard drive and uploaded windows xp professional. To my surprise I continue to get this box that pops up and says" Critical error message! Registry damaged and corrupted. To fix this problem: open IE and type www.registryxp.com Once you load the web page, close this message window. After you install the cleaner program you will not recieve any more reminders or pop ups like this one". I went to that page and it wants to charge me to sign up for a registry cleaner. This box pops up every 2 minutes or so . I've tried other registry cleaners and pop up blockers, spyware removal, deleting cookies, add/ remove programs, everything I can think of but to no avail. I know that it's hiding somewhere but I'm not too computer literate to go to far into my system without the proper help.
I am having a problem understanding when I load windows xp pro.before I did it without no problems,what I mean by that is my hard drives.I have two of them both are 500gb.one I had for avid editing and the c drive for other stuff like software.I guess I just got lucky before.I had both of them 500gb.but what I need to know please remember I am not a genius
Bought a new barebones PC and want to transfer my old hard disk with XP pro on it to the new machine.Back in the good old / bad old days of Win98 etc, it was easy to do this as Windows saw IDE as IDE and made no other requests to the system to fine tune, AFAIR.Now though if I transfer the drive I get a reboot, safe mode does the same.I can furnish more info from the boot log if required later but does anyone have a sure fire way of getting the GUI up and running so that it can start updating drivers etc.I'm also transferring the cdrom, dvdrw and most importantly the AGP graphics card so it's not an issue with that
a friend asked me to install a new hard drive for him because his crashed. So i purchased a new hard drive (maxtor 60 gb) set out to partition and format the drive, using a win 98 boot disk. I partitoned the drive ( for large volume drive.) Formatted the drive ( format c: /s ) to include system files.and proceeded with Os install Windows 2000. Everything went as smooth as silk... the when install finished, I was prompted to remove the disk from cd rom and complete installation with the onscreen prompt. I removed disk, clicked finish and the computer rebooted upon loading, when it went to start windows it said DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
I put the Win 2K disc back in and hit enter. It started windows perfectly no errors at all... then I took disk out re-started ( to check system stability) and back to the same error message: DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER. I of course freaked out, I feel like an idiot cause I cant get this thing to work right. tried reformatting without the sytem files, re-partioning tried win 98, winXP, nothing same stuff! So I talked to a pal got a hard drive wipe program off the net "killdisk", wiped the drive and tried to reinstall Win 2K, same problem.
Installed new hard drive, along with XP Home (recovery disk).Before my system crashed all my motherboard drivers were on D: partition.XP loads okay, but it is unstable - for example I cannot start msconfig under "Normal" start up. It crashes. I will not list all the BSOD - but XP doesn't like something.I have no devices connected apart from basic graphics card (which XP loaded the drivers for okay). I am waiting for XP Pro to be delivered, so I am hoping that my unstable XP will become stable after I upgrade (or full installation) of a retail version.
Prior to installing my current XP (one time of at least 30 others - as kept crashing),I tried to load my motherboard drivers from the disk my manufacture supplied.is it possible that my XP Home is unstable BECAUSE I do not have my motherboard drivers loaded? That might seem a naive question - but I honestly do not know, and I've started to become a tad paranoid as these problems have been ongoing for 5 weeks.
I just installed a new hard drive on my computer, it is a dell dimension E521, it had windows vista os on it, this was installed on the pc when I bought it ,after putting my new hard drive in I didn't have a recovery disk with windows vista but I did have an xp cd from my laptop so I've used it. The windows xp installed just fine on my pc but the problem I've run into is the drivers, the disk that came with it wouldn't work so I went to dell's website put in my service tag and downloaded all the drivers that it says my pc needs. everything installed ok except for my broadcom, which is not allowing internet, my warranty on this computer is out so I can't get any advise from them without paying a fee even though I bought the hard drive from them, and the computer! Just hoping I could get some help, and wondering if I have to install vista for everything to work right.
I have had a 60G external hard drive that has worked flawlessly for 2 years with both my desktop computer running Win98SE, and my newer laptop with Windows XP. This external drive was formatted with FAT 32 and NO PARTITIONS for all 60G. Because I have a Lot of music files and digital pictures, I have filled up the 60G drive, so bought an IOGear 160G external drive. This drive arrived partitioned into 6 partitions, of 20-32G sizes. This is completely wrong for how I want to use the drive. All my mp3 programs requires the library to be all in one volume, so I need 60-80G all in one volume just for music. IOGear support says that Windows XP does not allow volumes any larger than 60G in FAT 32. (This seems crazy since my older drive is all one volume and is FAT 32.
I have a Dell computer where one of the loading .dll files came up 'missing' one day, so it won't boot. I want to get all the photos and other docs off the hard drive. I had downloaded one version of linux and was able to see the files on the internal hard drive, but was unable to copy them to a memory stick or external hard drive. Now I've downloaded ubuntu and booted off a memory stick... this time, it's telling me that the internal hard drive has all kinds of bad sectors and won't let me access any of the files on there.
In the last few days, I installed a game I download from Downloads.com.During installation, this product installed SecuRom's copy-protection files to my C:Documents and Settings<User>Application Data folder,creating a folder there (SecuRomData).After uninstalling any downloaded games, and during a routine inspection of the <User>Application, I noticed the SecuRom folder.Since I have never had any such folder after doing a fresh install of XP, I began to wonder what this was. So I attempted to delete the folder, after using JV16 powertools to search the Registry for any SecuRom entries, and removing them.
