Pc Has Been Shut Down To Prevent Damage - Power Breaker
Jun 9, 2005
This problem just started yesterday, all because i think of when the power breaker went. It was in the middle of Shutting down windows and the power breaker went so my computer got shut off incorrectly. I started getting a memory dump screen when i tried to log into windows. So i put in the windows disk and did a Repair Install. that worked fine, I got it working and everything. Then I got a windows update installed from MS website... the whole Automatic Updare thing. Then I went to restart the comp cuz it was required, then my system could not load past the login screen, just always did a memory dump. so i went and tryed to Repair windows again, now i get this error
system is restarting automatically during the boot process. An error message is flashed briefly before it restarts: "A problem has been detected and windows has been shut down to prevent damage to your computer. "If this is the first time you've seen this stop error screen, restart your computer.If this screen appears again, follow these steps:"Run a system diagnostic utility suppied by your hardware manufacturer. In particular run a memory check, and check for faulty or mismatched memory. .
Try changing video adapters"Disable or remove any newly installed hardware and drivers. Disable or remove any newly installed software. If you need to use safe mode to remove components, restart your computer, press F8 to select Advanced startup options, and then select safe mode."Technical information: STOP: 0x0000007F (0x00000008, 0x80042000, 0x00000000, 0x00000000)"
I turned my computer on and after rebooting once, I pressed the F8 key and chose "disable reboot after system failure" and the blue screen said: A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen,restart your computer. If this screen appears again, follow these steps:Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated.Run CHKDSK /F to check for hard drive corruption, then restart your computer. STOP: 0X0000007B (0xF7B70528, 0xc0000034, 0x00000000, 0x00000000) I tried running it in safe mode but it never made it to the windows log-in
So first of all, I have a Dell Inspiron 600m with Windows XP Home SP3. Some background info that may or may not be relevant: I just had this OS installed though the computer is several years old (I had an ingenuine XP Pro before I cleared my C drive and installed a genuine XP Home). The XP installed was SP1 and then I did all the WUDs up to now I where I have SP3. Also, during that period, I had done a repair install because of some error I was getting following installation of a WUD. I don't know if any of that will be relevant at all, but just thought I should mention it.
I get this BSOD any time I unplug my laptop. It says, "A problem has been detected and windows has been shut down to prevent damage to your computer. .....
When i have had my computer on for a long period of time it sudely comes up with a blue screen sayying. " windows has had to shut down your computer to prevent damage.Does anyone know how i can over come this? Do you need the technical infomration to resolve this .
I have a ton of spyware and such on my computer and wanted to start fresh with a reformat. I put my XP disc in and tried to boot from the CD. When I tried to select a fresh partition I got the following error: A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you ahve seen this error screen, restart yoru computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.
Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as chaching or shadowing. If you need to use safe mode to remove or disable any components, restart your computer, press F8 to select Advanced Startup options, and then select safe mode. Technical Information:
*** STOP: 0x0000008E (0xC0000005, 0xF7418C13, 0xF6FD57E4, 0x00000000) *** setupdd.sys - Address F7418C13 base at F73EC000, Datestamp 41107c8f....
I was recently trying to install Medieval Total War II onto my computer. I've had it installed before in the past, and it worked fine on my computer. I wanted to play it again, so when I went to install it it gave me the blue screen. It said:Quote: A problem has been detected and windows has been shut down to prevent damage to your computer.PAGE_FAULT_IN_NONPAGED_AREAIt then said something about disabling BIOS memory options such as caching or shadowing, etc. Then it had what I'm guessing is the error code:***STOP: 0x00000050 (0x46263D6, 0x00000000, 0x804ED967, 0x00000001)
Computer keeps crashing and giving me this error. does anyone know what it means? A problem has been detected and windows has been shut down to prevent further damage to your computer. DRIVER_IRQL_NOT_LESS_OR_EQUAL If this is the first time your seeing this error, restart the computer. If it appears again, follow these steps. Check new hardware or software is properly installed. If this is a new installation, ask the hardware and software manufactuer for any windows updates. If problem continues, disable or remove newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safemode to remove or disable components, restart, press f8 to select advanced startup options, then safe mode. TECHNICAL INFO *** STOP: 0X000000D1 ( 0X0000000A, 0X00000002, 0X00000000, 0XA9BF66EB) *** ipnat.sys - address a9bf663b base at a9bf000, datestamp 415b3714 Begining dump of physical memory Physical memory dumb complete Contact your system administration or tech support group for further assistance. Then another time it crashed it game me the same top message, but a differn't technical info string...which is: *** STOP: 0X000000D1 ( 0X4D0FC400, 0X00000002, 0X00000000X 0X4D0FC400.
My computer is not booting up. A while back while using my computer a blue screen popped up saying that windows encountered an error and that it would shut down to prevent damage. When that happened I simply restarted my computer and everything was fine. This happened one or two times later and everything was fine. Today it happened again and when I went to restart it it the blue screen popped up immediately after that. On the third time I went to restart it the computer just said boot failure and did nothing. Every time I try to restart it does the same thing. It will let me press f2 for the start up settings but when I press f8 for safe mode it does nothing.
My friend got a blue screen with error message saying; A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time. Technical information: *** STOP: 0x00000024 (0x00190203,0x82346610, 0xc0000102, 0x00000000)
She can't get into windows at all. When I turn on her computer it goes to a black screen that gives me a choice to boot in safe mode, safe mode with command prompt, last known good configuration. It is Windows XP Dell Laptop. I've tried them all, everytime it just goes straight to the same Blue Screen with same message. She doesnt have a recovery cd with her.
I have an intel pentium4 system with 506 processor with intel motherboard (d101ggc) running on windows xp home with 512mb memory with one sata hard disk and two pat hard disks.Of late I have been having problems while shutting down after installing a software. the blue screen reads as follows."A problem has been detected and windows has been shut down to prevent damage to your computer. ****DRIVER_IRQL_NOT_LESS_OR_EQUA IF THIS IS THE FIRST TIME YOU'VE SEEN THIS STOP ERROR SCREEN, RESTAART YOUR COMPUTER. iF THIS SCREEN APPEAR AGAIN FOLLOW THESE STEPS.
My laptop won't even start windows in safe mode. I have the following blue screen:A problem has been detected and windows has been shut down to prevent damage to your computer.UNMOUNTABLE _BOOT_PROBLEM then a heap of stuff about checking the installation of any hardware or software. Technical information ***STOP: OXOOOOOOED (Ox8433BDD, OXCOOOOO9C,OXOOOOOOOO, OXOOOOOOOO)
I have recently been getting a "blue screen of death" or windows crash screen and have been trying to get a solution. I was running a computer game several days ago and began to notice crackling in the speakers every now and then and became concerned. When out of no where the game crashes and I get a blue screen thats says stop: A problem has been detected and windows has been shut down to prevent damage to your computer and it goes on to sya a bunch of other crap and at the bottom the technical code for the error reads 0x0000009c (0x00000004 0x8053FAf0 0xB2000000 0x00070F0F. I decided the best way to go would be a re-installation of windows. But anyways.
It has an MSI board, Celeron D cedermill at 2.2ghz. Western Digital 160gb sata drive. I don't think any of that really matters, but heres the problem. When trying to install windows XP, after loading all the drivers it needs and it gets to 'starting windows' a blue screen comes up saying something like 'your system was turned off to prevent further damage. The hard drive works fine in another system, and so doesn't installing xp. I put the hard drive with xp installed. It tries to load, same screen. But it installs windows 2000 without glitch.
My dell 9100 got a virus (Trojan horse XP antivirus) I got it off but avg anti virus would not update could not change the screen saver it posted and began getting the dreaded blue death screen problem has been detected and windows has shut down to prevent damage. the stop message is 0x0000008e (0xc0000005, 0xf84ca245,oxf808d7b4,0x00000000). So i reformatted the hard drive and when I go to reload xp it does not recognize the dell xp/media edition dvd. I have an XP home edition so I tried it and it allows me to get to the point where you partition the drive and then i get the same error message
Before I explain my problem, I'd like to say that this seems to be a registry problem. I tried installing Taksi three days ago and got this message "The system administrator has set policies to prevent this installation." and it didn't really bother me, checking out different software is a hobby of mine, it's not like I actually I needed it. I thought it was the developer's fault. But anyways, now I realize can't install anything that is packaged as an msi. I'm an administrator on my computer, but not the root, sadly. (I received the computer as a gift from someone who had no use for the computer and had forgotten their password.) First, I installed Windows Installer 3.1 over my current installation to no avail. After awhile, I found this: http://support.microsoft.com/default...;en-us;Q227181
my laptop just keeps on crashing. everytime i open my laptop, when it goes to the part where windows is loading it will reboot again and again, ive tried to use saftey mode, it doesnt work as well, and somehow i came to this blue screen. A problem has been detected and windows has been shutdown to prevent damage DRVER_IRQL_NOT_LESS_OR_EQUAL if this is keeps on.etc STOP: 0x000000D1 (0xF44690000, 0x00000002, 0x00000000, 0xF45695QE) rdbss.sys - Address F4469000 base at F4453000, DateStamp 445b1f4b ipsec.sys - Address F456950E base at F4569000, DateStamp 41107ec3 before this happened, my pc keeps on scanning while i restart my computer properly, normally if i shutdown normally with pc it shouldnt have done the scanning part
right i have laptop the windows is not english so i want to install new windows by booting when i try to do that the following errie comes up p#Blue screen, white text, following message (in summary): A problem ha been detected and windows has been shut down to prevent damage to your computer. PAGE_FAULT_IN_NONPAGE_AREA Suggestions: Restart computer, if problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing.Tech Info: ***STOP: 0x00000050 (0xBF32E9E4, 0x00000001, 0x805F87F4 0x00000002)[/COLOR][/COLOR]
I have an intel pentium4 system with 506 processor with intel motherboard (d101ggc) running on windows xp home with 512mb memory with one sata hard disk and two pat hard disks.Of late I have been having problems while shutting down after installing a software. the blue screen reads as follows."A problem has been detected and windows has been shut down to prevent damage to your
Im running Windows XP SP2 On a AMD Athlon 64 bit 3400Mhz Processor with a gig of ram. When i insert any disc into either the cd writer or dvd writer i get the blue screen of death saying the pc has been shut down to prevent damage to your computer. this one id doing my head right in
I am facing problem is starting my laptop.I get a blue screen saying windows have been shut down to avoid damage.And then it says 'UNMOUNTABLE_BOOT_VOLUME'and says this is caused due to new software or hardware installed. I have not installed any such application/software or hardware. So I dont know whats causing this problem.Can someone please help me at the earliest I am stuck badly.I need to work from home but my laptop is not working.
There's a very annoying program called dfg shutdown installed on my computer that shuuting down my computer at certain time.I can't uninstall that program.Is there a way to prevent my computer from shutting down?
I have this problem and i really don't know what to do....it always happens except when i am playing some games in full screen...A Problem has been detected and Windows has been shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen, follow these steps. Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to restart your computer, press F8 to select advanced Startup Options, and then select Safe Mode.
Technical Information: *** STOP: 0x0000008E (0xC0000005, 0x806FF94F, 0xB59E33C8, 0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact your system administrator or technical support group for further assistance.
I'm using Windows XP Professional as my O/S. I have a peculiar problem with my keyboard Logitech New Touch Multimedia with DIN connector. I have created two users, both with Administrative Rights.The problem is that the keyboard is detected only in one User. If I log off that user (the one in which the K.B is detected) and login the other, the keyboard stops working and all the LED's are switched off as if the Power to the keyboard is shut down. But on logging in the previous user, the keyboard starts functioning again.
My notebook has had a lot of trouble shutting down lately. When I go to Start-TurnOffComputer-Restart it goes to the Windows XP screen and says Windows is shutting down, but it won't ever restart. I lose my patience and hold down the power button after waiting for over 10 minutes.I've also had trouble with my USB devices. I have a printer connected as well as a Kensington Pocket mouse. These devices randomly shut off, yet the mouse never has problems when connected to my desktop.I sent the notebook off to Circuit City's national repair center about year ago under warranty. They fixed a burnt out backlight. Ever since they touched it, I have had problems with booting up and shutting down. A tech rep told me to re-install XP and I have several times, but it never solves the problem. I've run CCleaner, Norton Anti-virus, CWShredder, Ad-aware and Fixwareout. What else can I Do?
My neighborhood had a transformer blow and knocked out the power out within like 2 blocks and ironically im within that and when it happened my computer shut off and wouldnt turn back on anymore. (Prior to this happening every time i turned my computer on it gave me a windows message before loading saying something like "Alert, your power supply is low .. something something" im not sure if that has anything to do with it but yea..) now when i press my power button it flashes like its going to turn on but doesnt just stays off.
I have just had a mate of mine build a pc for me, from scratch, with all new parts. However, for some reason I get a random freezing of the screen resulting in a hard shut down from the Power button. This has happened a few times now, more than twice while in IE6 and once on the desktop. I originally thought it might be IE6 so I have installed IE7 and firefox just to be sure, then it froze while on the desktop straight after i logged in. The PC isn't running hot at all, as I said it froze after I logged in and there is definately no spyware or anything as its a new PC and the only thing i've installed on it is AVG & IE7.
Desktop Manager allows you to switch between multiple desktops creating more elbow room for those who like to stay organized while pushing the max thread limit.1. First grab XP PowerToys from microsoft.com Once installed right click then check: task bar > toolbars > Desktop ManagerYou may now view up to four new desktops. I prefer not to have "Shared Desktops" on as it reminds me more of linux (and is cleaner).Now you may hide the buttons etc. and use Windows key + 1-4 to switch between desktops and Windows key + v to preview.
I'm running WinXP pro and have lost all the reguler power schemes from the power options propreties window. Also I'm unable to Save a new scheme.I beleive the schemes where deleted from the power properties window by right clicking and selecting delete. They used to be there anyway Unknown is listed above Turn off monitor-Turn off hard disks-System standby-System hibernates and everything is greyed out. They are still listed in the registry but with no value set.How do I go about getting the schemes back?
My PC has old configuration, the Max Power Supply can be only up to 350W. You know that every parts of the PC, either external or internal hardware will consume power. What I would like to know is that, what would happen to my PC if the total power consumption exceeds the MAXIMUM VALUE of the power supply unit.
