I am running Windows XP on my PC. I have two WD hard drives. My C: drive is getting full (on my master drive). I have now an empty D: drive on my slave drive (I used to store my documents there, which I now moved to an external drive). Now I want to move everything from my C: drive to my D: drive. I know how to switch the jumbers so that the slave drive becomes the new master drive. But how do I move the system, files, everything, so that the System boots from current D: Drive (which will become the new C: drive). I do not want to reinstall everything anew, so I am not looking for a clean install, just a move of everything from C: to D:
I built a new computer w/ XP Pro. Its has a ASUS P4C800-E Deluxe MB w/ a 3.2 Mhz cpu. with a raptor hard drive. I set it up by installing the raptor alone, after xp was up and running I put the seagate 40gb in. It was running fine, when I took it out to put it back in the old system it was in it would not even start the check of IDE's. If I removed power from the HD it would say no IDE's found. I have award BIOS v4.51pg and when I hit delete I can't enter setup. (?) The only thing new to the old system is another video card (I put the old one in the new computer) I also removed the cd burner and dvd plyer and put it in the new computer, and a old dvd player was put back in the old computer. No setting were changed. I have tried to put the 40 gb back to the new comp and I get an error message w/ options to continue starting windows, start in safe, safe w/ com prompt, etc.
I have a Dell Dimension 8200 with a Pentium 4, 1.8 GHz. A while back, I installed a new ~75GB hard drive as the secondary drive (slave is the term, right?). Based on the fact that this is a newer drive, and on my own experience using the computer, I'm pretty sure the new drive is a lot faster than the original one. I'd like to make the best use of this additional speed, and was thinking about moving Windows and most of my program files to it. The older, 40GB drive could then be used for backup/archives.I've done some initial searches, both here and on MS's knowledge base, but couldn't find instructions for doing what I want to do. Also review www.michaelstevenstech.com, found the Move XP section, but still didn't seem like an exact match.
I have a Compaq Presario 900 which doesn't have a working CDrom drive.I took my harddrive out and put it in my friends Dell Inspiron B130 and installed Windows xp SP2. Now that all works fine but(there is always a but ....) when I tried to put the harddrive back into my laptop(Presario 900) Windows will not boot, even if I go to safemode first thing. I thought maybe I could install Windows from the USB port but my BIOS doesn't have a BOOT FROM USB option. Also there is no Bios update that will give me that option.I have tried deleting and installing all the drivers for the Presario then trying to boot like that but it still gets stuck.
I am trying to avoid reinstalling XP after moving to new hardware. I had SP2 installed and when I try to use the old XP CD SP0. some programs were not working and Windows update was not working and alot of other problems.
My main pair of raid drives crashed and burned. So I installed XP on my second pair of raided disks and recovered the data from the first pair. But now my boot/o-s disk is D and my drive is C.Any tools I can use to change drive letters around and move boot information and such automatically?
Let me be clear on this: I want to put in a larger drive than the old one, have Windows completely move itself to the new drive, and leave the old one blank - all without Windows' security hackles raising and saying, hey you changed something so you need to re-activate(I don't want to clone. I've done this and Windows has been a POS about it. I want to MOVE the installation.)Perhaps someone has some secret information that this is in fact possible?
I have 3 hard drives in my pc, and have been trying to move files and folders from one location to another. I do a Cut/Paste and XP starts to move my folders, showing that it will take say, 1 hour to complete.I come back an hour later and find that after a few files have been moved, the process paused because it ran into some "Read Only" or ".exe" file and it asks me if I really want to move it. This happens almost every time I move a bunch of folders.Is there some way to tell XP when you try to "Cut/Paste" not to keep stopping and asking if you really want to move certain of the files?
i am try 2 put things on 2 a usb device but it keeps coming up say this can not copy the disk is write protected remove the write protection is there anyway i can fix this thanks
I have a Dell computer where one of the loading .dll files came up 'missing' one day, so it won't boot. I want to get all the photos and other docs off the hard drive. I had downloaded one version of linux and was able to see the files on the internal hard drive, but was unable to copy them to a memory stick or external hard drive. Now I've downloaded ubuntu and booted off a memory stick... this time, it's telling me that the internal hard drive has all kinds of bad sectors and won't let me access any of the files on there.
My laptop died and I removed the hard drive.i hooked the hard drive up to my new laptop via a SATA/IDE cable.
I can see the old hard drive in the E drive and it appears that all the contents are there by the size of the hard drive (same as when I had it in the old laptop) but I can only see, actually view, a very small percentage of the drive.
My goal: I want to transfer all old music, word documents and photos from old laptop into new laptop.
current HD going bad, have second HD installed and using as back but now i need to make the second HD my primary, can i do this without having to reformat in order to add booting files.
using XP. am having wild swings in my hard drive space go from 46.1 to 44.1 and sometimes in between. have not installed any new programs recently. what could be causing it and how do i correct also am noticing my laptop as slowed appreciablydo know whether the two problems are correlated
i have a Compaq nx 7400 .i was hahving a lot of problems with the computer so i decided to put a new hard drive in and reinstall XP . well i have the new hard drive in and started up the machine and changed the bott options to run from the dvd and all went fine until i should press the ENTER ( return ) button to install XP now . as soon as i did that the next window said no hard drive found . this was also happening on the old hard drive that was in the machine .
I had this idea, see if anybody has an opinion about this. My wife has an old XP computer I want to buy her a new one but she doesn't like the vista and she wants to keep the old xp operating system. What I want to do is take the old hard drive and put it in the new computer as the master and take the new hard drive and put it in as the slave erasing the vista off it. Then using the master slave way can I transfer the xp operating system and all her files and data from the old hard drive to the new one.
I recently helped someone save the documents off of their computer after it crashed (it was missing a Windows file. I tried the repair command and it wouldn't work, so I decided to save the files and reformat the hard drive).I plugged the hard drive into a working computer and pulled all the documents off of it (VERY slowly) onto an external hard drive.
Every once in awhile I wouldn't be able to pull a picture or document off because of a cyclic redundancy check error. I just moved on and saved what I could. I assumed it was because the hard drive was already bad so I just moved what I could.
I am cloning my existing hard drive in my laptop (sata) to an external hard drive (pata) in preparation for installing a new larger hard drive (sata)in the laptop. Can I, or how do I transfer the cloned data from the external (pata) to the new internal hard drive (sata)? Thanks in advance and I apoligize if this is a rudimentary question as this is my first time attempting something like this.
I can not access hard disk properties because Windows Explorer hangs whenever I Right click on a hard drive icon. I am running WXP pro SP2 completely up to date with updates.
A problem has been detected and Windows has been shut down to prevent damage to your computer.If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again follow these steps.Check for viruses on your computer. Remove any newly installed hard disks or hard drive controllers.Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.
I am facing two problems with my lap top hp campac presario 2100. 1.The loptops battery to be changed. I dont know how many batteries are there. Any cmos battery there like any other pc. Pl advice. What would be the cost. and the model number . The hard disk requires replacement. I want to know the model numberor exact type of hard disk would be fit in. and the cost thereof.3. Windows xp home edition has been preloaded in the laptop. How to take a copy of the os and copy in the new hard disk. I have the serial number etc for the OS.
When installing a larger main drive, how do I get the drivers copied onto the slave before I take out the main one I wonder is there a simple way of doing this, I am using Windows XP home edition, the PC is an oldish one and isn't any specific make, so I can't get any clever programs from the manufacturers site
I use Cobian Backup to produce a zip-file containing all files and folders, except for temporary-folders (I added an exclude-filter), of my system.Before I can rely on this method, I need to find a way of restoring the 27 gb zip-file, which I store on a networked drive, easily. how booting up a laptop with a formatted harddrive, be able to access a network-drive and extract all the contents of the networked zip-file to the hard drive?
A little over a year ago I purchased a used IBM Thinkpad laptop from ebay for my wife. It came with Windows 2000 Professional installed and everything worked fine. No CDs or floppies came with the computer. A couple of months later, it was stolen by one of her business associates. It eventually was recovered, but the thief had installed Windows XP along with the OS that was already installed. In trying to remove XP and return the machine to its original state, I somehow managed to eventually not be able to use either OS. As it stands now I have no OS and cannot even access my hard drive.When I boot from a floppy then try to change to C: drive, I get the error message: Invalid media type reading drive c: Abort, Retry, Fail?
A friend gave me a laptop, my problem is that it came from Japan thus everything is japanase thus I can't hardly use it. The reason I accept it is bcoz he said I can try to reinstall a win xp with english version (btw, the OS is win xp pro in japanase version). Thus I bought win xp pro sp2 and try to reinstall it, so I reboot fm cd rom and while the windows setup is starting, the system stopped and the message on my screen read as:A problem has been detected and windows has been shutdown to prevent damage to your computer.If this is the first time you've seen this error screen, restart your computer. If this screen appears again follow these steps:Check for viruses on your computer, resume any newly installed hard drives or hard drive controllers, check your hard drive to make sure it is porperly configured and terminated. Run CHKDSK/F to check hard drive corruption. then restart computer. how in the world I can follow the above steps if everything written on it are in japanase language? I also try to visit the manufacture's website, thinking that perhaps it help solve the problem but....i also need a japanase translator to understand it.
I had to reinstall XP because of spyware issues. I saved important data on my slave drive. I reinstalled XP. Now the bios, device manager, and disk manager recognizes the slave drive but didn't assign it a drive letter. In disk manager it shows as a basic disk, NTFS, Healthy (Active), 18.65 GB,Online. When I right click the volume to assign a drive letter it is grayed out.
i screwed up my registry, and of all things it was the keyboard driver or something, so theres no hope of fixing it on my computer. ive got the drive hooked up as the slave on a different computer, but i cant figure out how to edit the registry on my drive rather than the primary drive. is there any editors that will open it from a file? any way of decompiling it? theres got to be some way to edit it. also, they are both xp.
I have just bought and installed (to the point of completing initialization under Disk Management) a new 1 TB hard drive. Originally, I was planning to use it solely for data storage.However, I am thinking of installing Windows XP Pro and all the programs I currently use on it, thereby making it the new OS and programs drive, while using the original 120 GB HD as a data/backup drive.I think the main appeal of doing this, for me, is that it also presents an opportunity to reinstall Windows on a machine which hasn't had this done for more than three years, and which currently seems to take at least five minutes to boot to a "usable" state, despite having a reasonably high spec for its age (it was bought in 2001, but as a result of the upgrade
