Windows 7 Cloned Drive Wont Boot?
Feb 16, 2013
I installed Win 7 to a SataIII drive/port with the intention of doing a bootable clone to a SataII drive/port. However on completion of the first install I realised that my cloning software was not capable of cloning the SRP (system reserved partition)Plan B ? Installed a second copy of Win 7 to the SataII drive/port on a single partition (no SRP) with the intention of cloning over the SataIII drive to eliminate the SRPWas hesitant to do this as the clone software wipes the SataIII drive so as a tester I cloned the SataII drive with the single partition to a spare SataII drive and it copied ok. Unfortunately when I disconnected the SataIII and SataII source drive the recently cloned spare SataII drive would not boot. The boot manager prompts the user to accept either of the two installed versions of Win 7 and whichever you nominate the spare SataII drive fails to boot. I installed the Win 7 repair disc to fix the start up but it displayed a message that it was unable to fix it.
View 1 Replies
ADVERTISEMENT
Feb 5, 2012
My problem is I have installed lion in one partition and cloned my windows to other partition. In GPT, Lion booting properly, but clonned system reserved and windows are unable to boot. If if use repair disc, it says not the proper version. ( created from the running windows). I don't have installation disc for windows ( home premium). I want to make the windows bootable.
View 1 Replies
View Related
Dec 23, 2012
I installed my sandisk pulse ssd 256gb sata iii on my sata ii moo via pcie sata iii card. every now and then I get the boot disk error messages - CTRL-AL-DEL to restart . I set it as my primary disk boot and disabled the wd blue from appearing on bios hasrd disk selection (which also has os installed)
I know I don't get sata iii speed on my mobo but am more worried about boot disk error messages.
any fix for this? should I reinstall my win 7 ultimate 64 bit upgrade on the ssd and start afresh? at the same time save all data to external hdd and wipe the OS clean off the wd 500gb - then copy all music and sundry back to the wd blue?
I plan to get windows 8 asap while the upgrade version is on offer till end of January 2013.
after my hardware plan works will a clean install of windows 8 pro upgrade wipe my ssd clean fixing the problem?
View 6 Replies
View Related
May 3, 2011
recently my 1Tb seagate decided that it's S.M.A.R.T. would fail so I went out and bought a 500gb to back up my data using HDClone as I've only used about 390gb on the TB and now I can't get the cloned HDD to boot at first when I booted it the screen would just stay at the flashing underscore which I recognized as an OS issue and I booted it with the recovery disk that did not recognize there was even an OS to fix. I can view all of the files if I use it as a removable disk so I know the clone worked I just can't get it to boot
View 9 Replies
View Related
Nov 22, 2012
My new ssd is running great, it feels like a new car.
But I am having trouble with my backups. When I unplug the ssd and try to boot off the hdd (which worked before I installed my ssd) I get boot manager screens.
How can boot off my clones? I'm using Windows 7 and did not change the BIOS except to boot off of CD for the ssd install.
View 1 Replies
View Related
May 16, 2009
I installed Windows 7 on my D: drive and it was only 80GB, and had everything running to my satisfaction. Started adding a few programs from my Vista install and thought the drive was to small, so cloned the drive unto a backup drive and installed a 1TB drive. Cloned the image back unto the new drive, but when I try to dual boot, it doesn't see Windows 7. I tried booting from the Windows 7 disk, to do a startup repair, but it doesn't see Windows 7 installed on the new drive.
Any ideas?
View 9 Replies
View Related
Jan 8, 2011
I have windows 7 x64 installed, and need to copy that partition to another partition on the same drive, and be able to boot between the two using EasyBCD. One will be normal/office stuff, the other will be music production stuff.I copied the partition (C) using Acronis (bootCD mode) no problem, then copied that Acronis clone to the new partition (D). Booted back in to windows and used EasyBCD to add the new partition (D) to the boot menu with a new name.Now when I boot I get the boot choices as expected, but no matter which one I choose, it always boots into the original partition (C)? I've used EasyBCD quite a bit before without problems but this one is driving me nuts.
View 4 Replies
View Related
Sep 29, 2012
So I have a system image from Windows Backup and Restore. Is it the same thing as a Cloned drive? If not, what differences are there?
View 3 Replies
View Related
Sep 16, 2012
The HDD had bad sectors and CHKDSK didn't complete, so I cloned the bad HDD onto a new good one.When I try to login I Explorer appears to crash and I get an the error code: 0xc0000022. I am able to login to safe mode though.Here is what I have tried1.Ran CHKDSK 2. Ran SFC /scannow3. Tried to run Win 7 Ultimate x64 SP1 setup.exe but I get "unknown error has occured" following the repair guide (Repair Install)The last thing I want to do is a new format, though it is looking like that will be my option
View 4 Replies
View Related
Nov 25, 2012
Desktop runs Windows 7 (64bit) Laptop runs XP (32 bit)I have programs on my laptop that I want to be able to run on my desktop. Programs that I no longer have install information/CD keys for. I have no trouble making partitions. A 'clean' install of XP onto the partition allows me to dual boot flawlessly using EasyBCD.What i *want* to do is be able to 'clone' my XP drive to the partition to be able to run those programs.
View 3 Replies
View Related
Feb 11, 2010
I had been thinking about upgrading to Windows 7 for sometime, and after my Raid array failed I wasn't forced to but it happened to be perfect timing.
Instead of waiting till my replacement drive arrived, I installed Windows 7 on a different drive temporarily.
After I received my new drive, I setup my array again and installed Windows 7 once again without a hitch. After installing all of my programs, games, etc. I started to notice both the User folder and Documents & Settings folders were both identical and were being updated simultaneously.
I know I didn't properly remove the old installation, but I've never seen Windows do this before. Very Odd. I've formatted the other drive and everything is good now, but I thought it was odd and wondered if it was a bug or a known issue.
View 3 Replies
View Related
Jan 3, 2012
I just purchased a second Dell M6300 and cloned the hd using Acronis. The cloning is supposed to produce a bootable drive. My problem is that the M6300 I just purchased has a 64 bit processor. After installing the 32 bit cloned hd my 64 bit unit won't boot. I tried using the Windows repair utility but that could not fix the issue. I tried installing Windows 7 32bit software again but it won't allow me to install it without booting to windows as I want to keep the programs and data already on the hd. Any ideas on how to get my cloned 32 bit os to boot on a 64 bit computer?
View 5 Replies
View Related
Jun 15, 2011
I just upgraded my XP system to Win 7 home premium 64bit.But after I installed it, I realized that the my HD is pretty old and may go out soon. So I ordered a new HD and it should be here in a few days.I know I can clone my current installation and copy it to the new HD, but will I have to reactivate win 7 if it is cloned to the same system?
View 5 Replies
View Related
Feb 23, 2012
I just purchased a second Dell M6300 and cloned the hd using Acronis. The cloning is supposed to produce a bootable drive. My problem is that the M6300 I just purchased has a 64 bit processor. After installing the 32 bit cloned hd my 64 bit unit won't boot. I tried using the Windows repair utility but that could not fix the issue. I tried installing Windows 7 32bit software again but it won't allow me to install it without booting to windows as I want to keep the programs and data already on the hd. how to get my cloned 32 bit os to boot on a 64 bit computer?
View 1 Replies
View Related
Oct 21, 2012
i copied the old hard drive from a lenovo laptop onto a samsung 830 SSDeverything works great except it won't recognize USB when i plug something in (in this case, a USB backup drive).it's strange because i hear that sound like it's in, and the light comes on the USB device, but "my computer" does not show the USB and the backup software does not show the USBwhat i've done so far is go to device manager and check everything under USB, they all say they are working properly.
View 1 Replies
View Related
Oct 4, 2012
I just cloned my ssd to my external hdd for work. On my external is an 80 gb partition that holds the clone of the ssd, the remainder of the space is a partition called G: When I boot from my ssd I can't access either partition on the external drive, although windows sees both partitions in the disk manager and says that it is in conflict with the data on my ssd. When I boot from the external I am unable to see let alone access the G: partition. I am aiming to be able to access the G: partition both from my ssd and from the ssd clone partition. Just a side note, when I plug the external into my netbook, everything is fine and I can both see and access both partitions.
View 3 Replies
View Related
Jan 10, 2013
had a hard drive fail on a netbook, and I put in a drive from another of the same brand that had died for other reasons. The new drive took like fish to water - no blue screens, etc. And Windows even updated, as did MSE.
But I'd like to make this machine honest by entering the Windows 7 product key that's associated with the motherboard, so the next owner will never have a problem. Will I have a problem doing that? I don't want to lose what I already have.
View 6 Replies
View Related
Jul 24, 2010
2 months ago, I installed windows 7 pro with no problems at all. Fast forward to today, I decided to reformat because the boot would get stuck in the middle of trying to boot into windows, it wouldn't flash the windows logo. I didn't think much of it so I just reformatted. This is where my real troubles began.So I reinstall windows 7 pro with no problems (the boot disk is in there the cd drive the entire time) I install my programs and what not and install my updates. All 100% Fine. Then I take out the boot disk and restart again... and I get this error message saying:
Nvidia Boot Agent 229.0525
Copyright 2001-2005 Nvidia Corp
Copyright 1997-2000 Intel Corp
Client Mac Address: 00 30 1B BC1F59 GUID: 12973077-FFFF-FFFF-FFFF-FFFFFFFFFFFF DCHP....
Then I press escape, then it says this:
PXE-EA0: Network Boot Canceled
PXE-M0F: Exiting Nvidia Boot Agent
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
So the first time I got this error, I just thought, Oh, something must have happened no big deal, so I reformatted again and again. But I kept on getting the same exact error. It'll load into windows just fine when my install disc is in the cd drive, but when I take it out, that error pops up. *My windows is authentic, each time I have been able to validate my copy.* I have tried installing from my hard drive and from the install disc with same error.*
This is my current set up:
Shuttle XPC SN27P2 (Barebone) Comes with motherboard, PSU, and case.
AMD Athlon 64 X2 5200+ @2.6GHz 65W
PNY XLR8 GTS 250
OCZ Reaper Memory 4GB PC-6400 DDR2-800
WD 74GB Raptor
WD 640GB Internal
WD 2.0TB Internal
WD 1.5TB External
WD 400GB External
Cavalry 1.0TB External
Shuttle 450 Watt PSU
Logitech G15 + MX518 + FuncPad 1030 Blk on Blk
Sony Optirac 18x DVD-/+RW drive
Dual Samsung SyncMaster 225BW 22" LCD Wide Screen Monitors
So how can I get windows to boot up with out having the boot disk in the cd drive...It worked the very first time I installed windows 7 on my PC...
View 6 Replies
View Related
May 29, 2012
My HP laptop HD crashed, am trying to replace it with a Kingston HyperX 120GB SSD. I do not have Windows installation disks, only have Windows Recovery Disks. All installation instructions I have found for SSD's is for cloning, which I cannot do since the HD is deadI have installed the SSD, booted into BIOS, this simple BIOS version doesn't allow me to change anything on the HD, but it does recognize it and let me do a HD test, so it does recognize the SSD. I then put the Windows Recovery disk in the CD drive, attempted to boot up, but the CD drive just spins and spins but never boots up. I thought the CD drive might be bad, so I tried an external USB CD drive with the Recovery disk, but it does the same (just spins). I even got a new Windows 7 installation disk (from another PC) to see if it will boot from it, but get nothing but a spinning CD I have not done anything yet to the HyperX SSD, haved not formatted or partitioned it.I thought this would be done by Recovery on the OS installationThe BIOS is set up to first boot from the CD drive, so the boot order is not the issue.
View 4 Replies
View Related
Jul 10, 2012
I recently built my computer and installed a ssd and a hdd, the OS is on the ssd which is the c drive but since it is smaller than the hdd I tried to change the letters around and make the hdd the c drive using regedit because the default install location seems to be the c drive and after restarting the computer it boots up and says preparing your desktop then goes to a blue screen with just the cursor. I tried booting in safe mode and all I get there is a black screen also
View 9 Replies
View Related
Jan 25, 2012
Check my Hardware specs for full information
Current setup:
C: Boot, Corsair SSD
D: Files, samsung HDD
D:/boot files/user/(all user account directories moved here, when possible) I'm wondering if it's possible to install games such as Assasins' Creed or Skrym, but install all game data to this folder?D:/boot files/programs/* Many installers allow you to define a custom installation path, But I am unsure if these games would ask for one or force me to install to the default directory?
View 9 Replies
View Related
Sep 30, 2012
I have a 1T SATA system drive and a 1T SATA working drive. I installed a 3T SATA storage drive, and now my system won't boot from the C:. I have to go into the BIOS and boot from there, or use a boot disk. How do I get the system to boot from C: again?
View 3 Replies
View Related
Mar 23, 2012
I have a partition question and after scouring the Web, can't find anyone with the exact same situation as mine. Basically what I'm wondering is if I can delete a primary partition and then extend another, non primary into that space.
Here's what I have and why I want to do this: my laptop came from the factory with one 500GB SATA drive, split into two partitions (C, primary, and D, logical, each 250GB). The Win7 install was on the C drive. Recently, I installed a 120GB SSD as a second drive, and using the tools with it, copied the contents of my existing C partition to the new SSD, and then made the SSD the boot drive labeled as the C drive. So far so good, everything works fine.
Now, what I'm left with is this: C: 120GB (SSD, now the boot drive with the Win7 install) D: 250GB (SATA, the original D partition, Disk Management IDs it as a logical drive, extended partition) E: 250GB (SATA, the original C partition, Disk Management IDs it as a primary partition)
So, I have the original "C drive" on E now... it's no longer the system/boot drive. Obviously I don't need the files on it as they are all on the new SSD. What I want to do is to delete all those files and then combine what's on D and E into one 500GB D drive as I have no reason to have the two partitions. Is it possible to just delete the E partition and then extend the D partition into the unallocated space? I'm confused because it seems as though the D partition may rely on the E partition being there since the E drive IDs as primary. Or would the D partition become primary?
I know I could just back up the D partition to an external drive, delete both D and E partitions, and reformat as one new D and restore the files, but I don't want to create more work for myself if I don't have to. Obviously I don't want to mess up the files on the D drive though, which is why I'm asking.
View 6 Replies
View Related
Jan 10, 2013
How can I move programs and files from my ssd boot drive to my data drive (Windows 7 x64 PC)?
View 3 Replies
View Related
Apr 26, 2009
ok so im having a weird problem thats probably very easy to fix.
background info: before my Windows 7 install i had 3 partitions
vista 64
xp 32
empty (soon to be linux)
when i downloaded the newest win 7 build i deleted my xp 32 partition and installed Windows 7 on that partition. because Windows 7 creates that "reserve partition" or what ever, it extended my EMPTY partition with my vista partion. which cause it to become a "logical drive" rather than a "boot" drive. aka i cannot figure out how to access my vista OS.. rather annoying since im just toying with Windows 7 atm.
View 9 Replies
View Related
Nov 26, 2009
For some odd reason, after doing some changes to my partitions in Windows 7 and restarting my computer, I got the ol' "BOOTMGR is missing" message. I have the Windows 7 Repair Disc image file and a 4GB USB Flash Drive, but, sadly, no CDs. Is there any way that I can put the image file onto my USB Flash Drive and boot from it with my Acer Aspire X1200 desktop computer?
View 1 Replies
View Related
Jul 25, 2009
I deleted my existing OS then created two new partitions on the same drive. Then I installed Vista on one partition and that partition was properly named "c" as ususal. Then I started Windows 7 setup.exe from a different hard drive and let Windows 7 install itself into its own partition. When I got to "My Computer" the Windows 7 partition was labelled as "I" instead of the expected "C" which had never happend before when I did the same thing.
Does anyone know a save way to label the Win 7 drive as "C" while in Windows 7?
View 9 Replies
View Related
Sep 14, 2011
is it possible to boot Windows 7 from a usb drive? does the bios support usb booting?
View 1 Replies
View Related
Aug 11, 2011
I've just purchased a notebook HP touch smart 13" tm2-2101 sl (the one you can turn the screen and use it like a tablet) without the DVD reader.I want to know if it's possible to create a bootable file to restart Win 7 after a reset of the system on a pen drive USB instead of the DVDs.
View 3 Replies
View Related
Feb 14, 2011
I'm not quite sure if I myself can fix this but I've been using my computer for about a year now just keeping the installation disk in the drive.. If I remove it, it will not boot when powered on. It hasn't always done this. When powered on without the disk it says something like "please insert cd or dvd"
View 7 Replies
View Related
Jun 3, 2012
I didn't really know if this is the correct forum to ask, but my usb 3.0 drive (Western Digital) is not being seen upon boot into Windows 7 on my homebuilt system. If I plug it into the usb 3.0 port after it is booted, Windows will see it and initialize it, etc, but not if it's alreay plugged in when I first turn on the computer. My comp specs are below.
comp:
ASUS P8P67 mobo (standard, not Pro)
intel i2500k CPU
8 gigs Ram
500 gig WD main drive
ATI vid card (can't remember model off hand)
View 11 Replies
View Related