I needed to upgrade anyway, so I bought a new motherboard, new SATA HDD and a new copy of Windows 7 Home Premium..I had problems with th initial install, it started hanging three quarters of the way through, I checked online and found that if I disconnected all USB connections it installed fine.Now installed it won't load up correctly, or if it does it crashes almost straight away, it runs fine in safe mode, but I can't use Windows Update in safe mode.Rather than reinstall again.I've got the feeling the problem may relate to the build rather than the software, but wanted to check if anyone had experienced similar problems?
I just put together this computer on the 2nd and since then I've blue screened 9 times. I've done some research and all the drivers are up to date, to the best of my knowledge, and I have installed all the updates from Windows Updates? I'm not sure what to try next.I downloaded the 'SF Diag Tool' and have attached both the minidump and the system information.
Last night, I built my first desktop machine. Most of my components were brand new, but I kept my old hard drive.(Which contained my Windows Home Premium 64 bit OS on it.)
When I finally went to power it up for the first time, it booted up normally, and then when it goes to the black screen with the colors swirling together to make the windows logo, right away it quickly flashed to a blue screen and then restarted.
I then went into the repair windows mode, but the automatic repairs failed. They left me with these details:
Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: 21200924 Problem Signature 05: Autofailover Problem Signature 06: 3 Problem Signature 07: No Root Cause OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 1033
The hard drive with the operating sytem was working fine for me yesterday in my old machine. So I am assuming it has to be a problem with the new hardware, or I failed to connect something, or i need to change a setting.
I have put together a computer, new motherboard, processor, hard drive, everything. Now I'm trying to install Windows 7 from a boot DVD, but obviously have no drivers installed, so my computer doesn't communicate with my monitor. I guess I'm stuck between needing the driver installed, but needing Windows to install the driver? Do I need to install MS-DOS or something first?I have a completely blank hard drive. Trying to install Windows 7 Pro, 64-bit.
I just built a new computer ordering the parts online & putting them together and I have come to the stage of trying to do a fresh Windows 7 install on the HDD. But, for some reason when I get to the step of selecting which hard drive to install on, Windows can't detect my hard drive. A Samsung 1TB F3 Spinpoint SATA II. The weird thing is that it shows up fine in the BIOS. I've tried changing SATA connection port on the motherboard (this changes which channel it is listed under the BIOS. i.e Channel 1/2/3 Master/Slave) but Windows still can't detect it. So apparently I need to format the hard drive before I can install Windows on it. I've been told this is easily done using the Windows 7 disk but I am still having no luck. It can't detect the hard drive to format in the first place. When I press Esc to go to the boot manager there isn't an option to format there either. And when I browse for drivers under Windows installation, I click on C and format and an error message appears saying check that it's connected properly or it's read-only. I have also tried burning boot disks and running them but they just won't run when I insert of disk and boot from CD-ROM.
For some reason, I cannot install Windows 7 onto this new gateway PC that I have, but am able to do it on my older PC. Both are capable of running 64 bit, both have new and working memory, hardware. Now I understand that when you do install windows for the first time, your hard drive "marries" your motherboard. Thus when I put the hard drive into the new machine after a fresh install, it gets stuck on "windows is starting" and refuses to boot (ClassPNP.SYS in safe mode).
I am going to build a new pc from scratch, I already have a windows 7 installation disc and an windows xp installation disc from my old pc that i bought. I am worried when I try install the windows 7 os on the new build it wont work because when i put the disc in my laptop the auto run comes up and says run setup.exe, but as far as I know that is a file that is associated with windows (and the new pc wont have an OS yet) Is that file just for upgrade purposes? because on the disc there are also many other files and folders.Does that mean I will be able to install the OS on my new system from the BIOS menu or will i have to install the old xp OS and then upgrade
So I recently put together a computer for a friend of mine. We booted it up, and everything seemed to be fine. Unfortunately, he has been having intermittent BSOD crashes, often when installing new software (though not always). We've tried reinstalling Windows 7 (64 bit) several times, and I've had him run various RAM and hard drive diagnostics, which have (so far) not indicated any issues. My suspicions are beginning to point towards the motherboard or power supply, but honestly I'm pretty inexperienced when it comes to analyzing dumps. I've attached the relevant dump files. I don't have a full list of hardware directly at my disposal, but if necessary I can have him run a dxdiag tomorrow.
I have just built a new computer and i am wondering if it is possible to use my old windows 7 OS on a hard drive on the new computer. old computer was a HP pavilion elite-141f and the new computer has AMD fx-8350 , asus GTX 660 TI and a gigabyte motherboard
I have built many computers but am having a little bit of a problem with some things and my new one. My new install went great. All programs installed without a hitch. Fast and furious is the way it went to get everything installed. Now, after a week or so I have started having a couple glitches. When I go to install a new program or update it the program just sits there for 4 or 5 minutes before doing anything and then finally starts to do its thing. The other issue is that I am trying to do a backup and image clone to get my new system backed up. The problem there is that the windows backup won't see my hard drives. I then tried Norton Ghost and the same thing happened. What is causing this?
Alright I am running Windows 7 ultimate x64 on my newly built computer. My computer can successfully boot past the bios and get to the logo screen. Then I get to the Windows logo which is a hit or miss. Sometimes it will boot successfully and I will have no problems whatsoever and I can enjoy my computer without worrying about anything. Then sometimes it will get hung on the logo and it will just stop responding. I don't know if this is an issue with my HDD or maybe my power supply. I think that this may be a problem with my power supply because I notice that my keyboard LED turns of when it hangs like that. The only question then is "why is this not a consistent problem that I can isolate?"
Here are my specs: Case: Coolermaster HAF 922 CPU: Core i7 3930k (3.2 ghz stock; will OC to 4) Motherboard: x79 Asrock Extreme 4 (x5 sata 6.0 Gb, x2 usb 3.0 ports, PCI-e 3.0 support, and quad-channel memory) RAM: 8 gigs (2x4 gig's) of 1600 DDR3 GPU: x1 Radeon 6870 PSU: 600 Watts HDD: 500 gig's 7200 RPM (Seagate baracuda) Cooling: closed loop liquid cooling, Tuniq TX-2 High Performance Thermal Compound, and the standard fans on the case Optical drive: LG 12x Blu-Ray reader and DVD combo drive Monitor: 22" LED 1920x1080 -- ASUS VS228H-P (21.5 viewable)
I have recently built myself a PC (Windows 7, i5) and it's running fine except for one problem. Every now and again, when I've been away from it, I find that it's reset itself. I don't think it's overheating as the machine has two extra case fans and the temps seem fine.How should I go about starting to investigate this as it has never reset itself while I've been there.
i built this computer on june 23rd, had zero issues. i oc'd it to 4.5ghz on the 25th, have been playing crysis 1, and nfs undercover with no issues. i've run both at the same time while running prime95, and having core temp up, averaging 53c.
[code]...
listed above is all of my components.the crash happened while i was transferring files from my slave drive to my external drive.my cousin was using the computer, watching a video on Internet.the dump file is attached to this thread, i'd analyze it myself, but i haven't the slightest clue how.the bsod error said: stop 0x00000124
why a newly built PC keeps getting BSOD and doing random shutoffs. I have replaced the memory and MB and have tested with and without the video card or OB video. I have also tried a different PSU to see if that would help. I am leaning towards a bad CPU or incompatible memory, but wanted to see what you folks think first. Also, the system has been reloaded twice. The first time was a new install and then I reloaded everything after I installed the new MB.
edit: forgot the system specs: OS - Windows 7 Pro 64 MB - Gigabyte GA-Z77-D3H CPU - Intel i7-3770 RAM - Patriot PD000256-PXQ316G1866ELQK PC3-15000 1866MHz 16GB (4x4GB) Kit Video - AMD FirePro V4900 1GB DP/DVI HF PSU - Rosewill Hive-650
I just built a new computer and whenever I play the game CoD:mw3 my computer randomly crashes, sometimes it'll show pale blue on my screen sometimes it'll be yellow and there really is no specific timing for it either. I've already upgraded my drivers.
So I built a new computer yesterday and when I ran a speed test today I was only getting 9.5mbps when I usually get over 30mbps. It has something to do with this computer since my other computer is getting 30mbps. And yes this computer is connected directly through and ethernet cable.
When I first installed windows it started to work just fine but I soon noticed that it would randomly freeze every 15-30 minutes of use, but not on a particular program or anything. I assumed it was drivers so I installed the latest drivers for my GPU and MOBO and keyboard. It seemed fine again until it started crashing again. I ran a GPU burn test and a CPU burn test it passed both. (I tried runing memtest86+ but it froze at like 12%) Then I tried fixing the registry so I downloaded ccleaner and fixed the registry problems. Freezes continued. I finally decided to re install windows so I did and the problems still continued. I am at a loss of what to do and can't think of anything else.
I got all the motherboard drivers and the video drivers installed then when i installed the drivers for my wireless network card and restarted and it froze on the starting windows screen.
I've been trying everything i can think of to fix this. I pulled the extra memory out, switched the power supply with one from another rig, switched the hard drive out for another one that i had.
after that, since it was a fresh build and nothing was saved on it i tried to reformat the hard drive and re-install windows, but the install disc also freezes on the starting windows screen.
so now i can't get it boot normally, in safe mode, from the disc or from another hard drive. when i try and boot in safe mode it stops at ClassPNP.sys
I'm working on a computer that appears to have gone through the "Windows Recover" virus/malware. The user appeared to do a good job of removing the virus and used System Restore to dial the system back about a week (which unfortunately is the furthest back the restore points go for some reason). Everything seemed to work except for the main users account, which had it's profile locations changed to something like c:usersTEMP.username-PC.000. It was pointing to this directory instead of the original directory. I then opened up regedit and found the entries atHKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionExplorerShell Folders all pointing to the wrong folder, so I manually edited every entry to point to the correct folder and restarted.
This ended up working against me. When I logged into the account none of the shell folder shortcuts in the start menu would do anything when you clicked on them. The menu would stay up and it was as if I was clicking on nothing at all; no response.Instead of reversing the edits I had just made manually I decided to try using System Restore to revert the system back to the earliest date, which the owner of the PC said they had done themselves before I got there. I figured the worst that could happen would be it would be just as it was when I first looked at it.After performing system restore I can only log into the Administrator account.Every other account on the system produced the error message "The User Profile Service service failed the logon. The user profile cannot be loaded."
I just had my newly installed Windows 7 32 bit system crash. Here is the error code from the event viewer. Can anyone tell me what I can do to resolve this error?Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected.
Some when we're installing applications they're requesting for "Restart PC before use that Software" (You must restart PC before use this software). So are there any way to run that newly installed application without restart PC or longing-off PC.
I have an ASUS G73 laptop and have installed an OCZ 240GB SSD drive. The laptop currently has Windows 7 Home premium 64 on it on the original drive. I would like to install a new Windows 7 Professional 64 version on the new drive and be able to dual boot. I have formatted the new drive and it is recognized in My Computer and I can save files on it.When i tried to install 7 Pro, it would not show the new drive as an option to install on. I tried this by inserting the disc in the DVD drive and by rebooting with the DVD in the drive. I also took the original drive out of it's bay and tried to reboot and could not get it to install. I then moved the new drive to the original drive's bay and rebooted and could not get it to install.When you all finish giggling about all the stuff I went through, could you post a guide on what I can do to get it to install?
Installing W7 using an old HDD on an old machine to install W7 on a new SSD to be used on a new machine.I'm currently using this old machine from '09 and its performance levels have died down a lot. I bought all the components to build a new machine except I didn't want to spend extra money on another HDD to install the OS on my new 180GB Intel SSD. So basically, I want to use the HDD from my old computer, install W7 onto the SSD, then transfer the drive to my new computer, and use it on the machine and just reinstall all my other files.
A newbie and i want to build my own computer..i would like to assemble the parts on my own..can u guys give some guide to install the OS on a new built computer..can i install win 7 using usb drive on a new pc? im planning to buy two HDD..can u guys give a guide to set up RAID0
I plan on reformatting Windows 7 x64 due to some hardware issues. Basically, I would like to be able to have things like Windows 7 settings, themes, ect imported. Any tips on how to do this? I do have separate partitions/harddrives to backup files, program data, ect.
I need to upgrade from Win XP 64 to Win 7 x 64. 1/ What is the difference between Win 7 Oem version and Win 7? Can I use either - are there problems? 2/ Occasionally I need to do a clean re-install ( Upgrading PC neds HDDs etc). With XP 64 re-activation is not a problem, I bgelieve Win 7 only permits one activation - is this correct and if so how are cases such as hardware upgrades and fatal crashes handled?
I just built a computer, but it will not load an OS. I got Windows 7 x64 to load once, and everything worked perfect for about an hour while I updated my drivers and whatnot, but then it froze and erased the hard drive. I've been trying to install it the exact same file in the same way off my flash drive and it just won't work. I've tried to switch the ram around and remove one each time, using the cd, using a friends cd, using new connectors from the cpu to each drive and I even tried installing Windows Xp pro but it didn't work for any of that. Here are the parts that I put in my computer, maybe some aren't compatible with each other? [code]
First time building a new pc. A new motherboard, new dvd/rw ram, old hard drive. I used the old case from my old computer - power supply was already connected so did not change it. System boots up fine but when I start to install windows computer shuts off. I have a seagate hd so I downloaded seagate tool and wiped the hardrive because I was thinking that may be the problem. Tried to install windows again computer cuts off. Whet in and checked the ram using windows.
I guess my title says most of what i want. I've ordered parts for a new pc, but because of my budget I did not buy the cd drive in order to buy better parts for my pc. For two years, I've never used my cd drive so I didn't need it anyway. But now I need a way to install windows 7 on my pc without using the cd drive. I have a question if there is a way to install windows with a usb. I have a laptop at home which i can use to create the usb.
