No Bootable Device Error, Can't Start Computer?
Nov 7, 2012NO BOOTABLE DEVICE--INBSERT BOOT DISK AND PRESS ANY KEY FOR REALTEK RTL8102EPCI-E ETHERNET CONTROLLER v1.07 (080320) media test failure, check cable
View 2 Replies
ADVERTISEMENT
No Bootable Device Error, Can't Start Computer
May 29, 2012My Toshiba Satellite L755 is receiving the following error at startup:
Check cable connection!
PXE-M0F: Exiting Intel PXE ROM.
No bootable device -- insert boot disk and press any key
This occurred after I used Toshiba Wizard to clear the hardrive. I was attempting to get everything back it's original state.
So far I have gotten into setup by holding f2 at startup. The boot tab reads:
1. HDD/SSD Hitachi HTS545050B9A300 (S1)
2. USB
3. ODD TSSTcorp CDDVDW TS-L633F (PM)
4. FDD
5. LAN Atheros Boot Agent
I have also tried disconnecting the battery and harddrive and then reconnecting them.
No Bootable Device Error?
Jun 30, 2012I have an Acer Aspire On 10inch Notebook that runs on Windows 7 Premium Edition (32bit). I'd been having some troubles with its speed for a day or so and since I'd neglected to do a Windows update. So, I restarted it and hoped that once it installed those updates everything would be fine. My first warning sign was the time that it took to turn off - probably 15 minutes was spent with the screen continuously saying "Shutting Down" and I took this to mean that it was probably a series of updates that I had missed. So, I left it to sit and came back to check on it afterwards.When it finally finished, a black screen took over and sat there for quite some time. Eventually I grew frustrated and restarted the computer, and saw the 'Acer' screen come up, and then the computer screen went black again and a command line started, where I received this message[CODE]
View 3 Replies View RelatedNotebook - No Bootable Device Error
Oct 4, 2011i have an acer aspire one notebook and one day it was working and the day after when i turned it on it goes to the normal acer loading sign then the screen goes black and makes a beeping noise for about 10 seconds then this error comes up
Intel UNDI, PXE-2.1 (build 082) Cpoyright (C) 1997-2000 Intel Corporation For Atheros PCIE Ethernet Controller v2.0.0.9(05/08/09)
Check cable connection! PXE-M0F: Exiting Intel PXE ROM. No bootable device -- insert boot disk and press any key When i click enter this message just appears again.
No Bootable Device Error On Toshiba Laptop
Oct 7, 2012I was just on the laptop browsing the internet as normal then all of a sudden out of nowhere it shuts off. Turn it on again.
I get this screen: [URL].
Then I got to the BIOS: [URL]
Then checked bootable devices: [URL]
The HDD is still connected: [URL]
So what do I do? I have valuable files and photos on this hard drive and do not wish to reformat or reinstall my OS.
Upgrade Error - Cant Find A Bootable Device
Nov 22, 2009I have XP Pro64 bitand I am trying to upgrade to Win7 64 bit, While it is unwrapping files there is a point where it needs to reboot. When it does it comes up with the error saying it cant find a bootable device or something in that effect. I removed the win7 dvd and hit the restart on the computer. Install continues. It completes but when I try to put all of the data back in I cant open up my user name (Documents and Settings ) folder has a lock on it. I finally gave up and I am reinstalling XP Pro64 bit again as I type.
I will try to upgrade again.
Can anyone explain why when it reboots it wont just continue to install with the disk in the Drive?
Why there is a lock on the folder and wont let me access the files?
Random MBR Error In Windows Update - No Bootable Device?
Jan 10, 2012I was in windows update when all of a sudden laptop went into dos mode an shutdown. Went to restart an I get "no bootable device"?
View 1 Replies View RelatedNo Bootable Device - Insert Boot Disc Error
Dec 16, 2012I have Windows 7 on a AMD Phenom Machine. Hard Drive died so I put another one in and restored Windows with Acronis True Image.
When I leave the Windows repair disk in the drive, the restored system starts perfectly, runs perfectly etc. But if I pull that repair disk out of the drive I get this error about "No Bootable Device" "Insert Disc". So in other words that repair disk has to be in the drive, else I get the error.
I have already:
1. Verified that the boot sequence points to my Windows Drive
2. Run system repair. That's useless. It just tells me everything is fine.
3. Run bootrec fixmbr, vixboot, rebuildbcd. No problems found
4. Run Chkdsk. No problems found.
Error At Boot : 0xc000000e - The System Has Failed To Start Because A Required Device Is Inaccessible?
Aug 10, 2012Okay, so this just happened out of nowhere. Nothing seems to have led up to this -- the system booted and shut down successfully, and no software updates or installs were done during the period of time it was on when it was last working. I've attempted many things, but none seem to work. /ScanOs reports no OS detected, while startup repair said the OS was booted successfully. bcdedit also shows no directories linked to "unknown". CHKDSK reports no bad sectors, so such can be discarded. This happens every time I attempt to boot to Windows 7 (Home Edition, x64). I have a copy of Fedora 17 set to dualboot with it
View 14 Replies View RelatedNo Bootable Device?
Oct 7, 2010when i turn on thers a blank screen saying f2 and f12,iv,e pressed both and nothing happens,just a other blank screen saying no bootable devices, i connected a external hard drive and put a windows disc in to try reinstall windows,but still nothing ,windows goes through the motions,and then says something about not been able to find a hard drive
View 9 Replies View RelatedNo Bootable Device Found
Jul 21, 2011I have a Dell Inspiron 546 running Windows 7 Ultimate.Last week after a reboot I got an error stating no bootable device found. I checked the Bios everything seemed in order and out of desperation I reformatted the drive and although shes runnning like new again the same error appears. If I insert the installatin DVD it boots normally.
View 3 Replies View RelatedHow To Make A USB Multi-Bootable Device?
Aug 3, 2009I have a 16GB USB drive sitting here calling me.. I have a project I want to do with it as well.
I would like to have Windows 7 32bit, Windows 7 64bit, Hirens Boot CD 9.9, and Windows XP all on the usb drive for install.
So basically I would boot from USB a menu would pop up and a choice of one of these 4 systems would be presented. Once you pick that Disk it would bootup to the install or application selected.
I was able to make a x32 USB Windows 7 stick but im confussed how to do a menu and allows multiple bootable images on a USB drive.
Compaq C700 Laptop: No Bootable Device
Jul 27, 2010I have a Compaq Presario C700 which is giving me the following error: No bootable device -- insert boot disk and press any key.
I'm a technical user and have been able to fix just about anything, until now. I've done some research, and I've found that this Compaq C700 is a terrible computer that just can't be fixed. They're probably right.
I've tried to boot off an external optical drive, but this failed to load the system. I've checked the boot order is correct and that the optical drive was enabled in the BIOS, but this still did not allow me to boot from the optical drive. I knew that it recognized a system there because it had an underscore, which meant it was trying to boot from the disk, but sadly, no luck.
As for the hard drive, I've replaced it with a spare, couldn't install Windows 7 on it directly from the laptop, so I installed it on my desktop system, then put it back in. Still, the message. No bootable device -- insert boot disk and press any key.
I've verified every available BIOS setting to the last detail. The only thing I could think of and haven't yet tried is to try to see if there's a CMOS battery anywhere and disconnect that, but I'm not sure where that could be on a laptop, and taking this thing apart is practically impossible.
I know the CPU and system board and everything else seems to be in working order, it's just that it can't seem to work off of a Windows 7 disc or installation. A red flag for me was when I went into the BIOS (InsydeH20) it mentioned that Vista was the factory installed OS. I wonder if it's doing this because it's expecting, and is proprietary to, Vista.
No Bootable Device Insert Boot Disk?
Nov 20, 2012the hard drive failed... i like to install an external hard drive. I have inserted the recovery CD...removed the failed hard drive yet the error stops to recover
View 1 Replies View RelatedAcer Aspire One Had A Message Displayed Saying 'No Bootable Device
Jun 19, 2012My Acer Aspire One net book displays a message when I switch it on. It says 'No bootable device..please restart system'. How do I do this?
View 2 Replies View Related0x80070002 Error Can't Start Computer
Jun 6, 2011I recently have had major issues with my HP pavilion dv6 laptop. I bought it about a year ago, and it has worked reasonably well until now. I downloaded some iso files, and I wanted to run them, because they were an old game that I really liked of my friends, but he sold it. I tried to copy it onto a disk, but the disk was playing up, so I downloaded DAEMON tools lite so that I could install it. I then had to restart the computer, as you have to with new software, and It seemed fine. I then turned on the computer the next day, and the CHKDSK program ran. I didn't worry about this too much, it happens occasionally.but when the computer started up properly; it wouldn't run any programs. when I tried to get things to go, it would always come up with a balloon in the corner saying that the file system structure is corrupt or unusable, please run CHKDSK on file system C:. So I did. The next day(today), everything worked fine. I could do just about everything. I told CHKDSK and the memory diagnostics tool to run while I was at school. I didn't notice anything bad at the time. Everything worked when I got home from school; except that most of my gadgets had no writing on them, which concerned me a little, and some of my startup programs didn't start.
View 4 Replies View RelatedComputer Can't Start Mpfilter,sys Error
Jan 5, 2013So when ever I try turn on my computer it fails to do so and has a \windows\system32\drivers\mpfilter.sys error.I'm Running off Windows 7 Gigabyte ATI motherboard,I've Tryed Booting in to Safe mode doing a system Resystem restore to previous working point and everytime I do it goes strait to saying \windows\system32\drivers\mpfilter.sys error...
View 1 Replies View RelatedError 0xc00000e9 ; Computer Won't Start
Jan 4, 2013i have a dell inspiron Laptop and I'm running (or trying to run) windows 7 home 64 bit
1.)One morning windows would not start all or a sudden (i'm guessing due to an automatic windows update), it would only let me go into the recovery mode.
2.)I tried several of the recovery options to no avail until i finally got one to work.
3.)After that windows was working but was EXTREMELY slow despite my best efforts
4.)I decided to do a complete factory restore using my restore disks (the ones you make when you first get the computer)
5.) this worked perfectly and windows seemed to be running great until I restarted, and on the restart it took me to a black and white screen that gives me the 3 instructions (none of which help). the status on that screen says 0xc000000e9
6.) the only thing i can do is boot to the recovery disk and reformat again, and the same thing then happens: windows works great until i turn off or restart, then I'm back at the black and white screen.
Unable To Start Computer Without Receiving Error
Dec 19, 2011I have an Asus laptop with Windows 7 Home Premium. Last night it started having a problem where it cannot boot and gives the following error on a blue screen:"STOP: c0000135 The program can't start because %hs is missing from your computer. Try reinstalling the program to fix this problem."I've found some threads linking this error to AVG, so I've already followed these directions:url...However, I'm still unable to start the computer without receiving this error.The computer has also attempted to run "Startup Repair" but it just says it "cannot repair this computer automatically."
View 4 Replies View RelatedKeep Getting Runtime Error 2 At 00004ad4 When Start Computer?
Mar 25, 2012i keep getting runtime error 2 at 00004ad4 when i start my computer.
View 6 Replies View RelatedWindows Cannot Start The WLAN Auto-config Service On Local Computer, Error 1068
Aug 12, 2012I am unable to connect to the Internet on wireless home network.I have carried out the following:'Click Start, type services.msc, then press Enter. Scroll down to "WLAN AutoConfig" and right click on it and select Properties. Set it to Automatic and not Disabled, and press the Start button, then click OK.That should start the service.'I received the following message:"Windows could not start Wired AutoConfig Service on local computer.Error 1068: The dependency service or group failed to start."
View 1 Replies View RelatedThis Device Cannot Start. (Code 10) Imaging Device
Dec 9, 2012My webcam is not working on skype and when i go to check the image device i get this (This device cannot start. (Code 10)... message on the property.
View 2 Replies View RelatedComputer Says No Bootable Devices?
Oct 10, 2012my laptop when i turn it on says no bootable devices??? what should i do??
View 1 Replies View RelatedComputer Hangs After Post (unless There's A Bootable CD In Tray)?
Jun 12, 2011Computer posts, then checks hard disk RAID status (Healthy), then a white blinking cursor appears on upper left corner on black screen, and hangs there forever, UNLESS i put in a Windows bootable CD, then based on my boot priority order (CD ROM, HD) it reads the CD, then it displays "Press any key to boot from CD or DVD...", for which i don't press anything, and the computer proceeds to boot Win 7 OS correctly. So basically it doesn't boot unless i just have a bootable CD in tray.
View 10 Replies View Related'Error While Opening Sound Device. Check The Input Device Settings And The Project Template'
Mar 1, 2010I have an emu 1820m soundcard installed in my computer. It seems to be functioning perfectly. I can play dvd'd, cd's, iTunes, etc and the sound plays through my speakers without a problem. I want to record some sounds from a dvd but i cant get anything to record. Recording device is set to Wave EMU DSP as the default device. Im using Audacity to record and have set the recording preference device to be Wave (E-MU _-DSP). When I hit record I get an error 'Error while opening sound device. Please check the input device settings and the project template'And I cant record anything.In the built in Windows sound recorder, when I hit record, I get this error 'An audio recording device cannot be found' Everything seems to be functioning perfectly, yet i just cant record anything.
View 8 Replies View RelatedWindows 7 Usb Camera Device Shows Up In Device Manager But Not Computer
May 31, 2012Have recently purchased a small usb inspection snake camera with led light and when testing it plugged it into two desktops computers (one xp pro not sure of the other as it was a network work computer) It automatically loaded the drivers and brought up a screen automatically with the realtime image.(no driver disc came with it). However plugging into my windows 7 64bit sony laptop it signals a connection beep, loaded drivers automatically but wouldn't open or show up on my computer disc manager as an external usb source to click on. It does however show up on device manager as a usb camera and when I unplug and replug in it disappears and reappears so I know I have the right camera (not the lap top webcam inbuilt one that shows USB 2 Camera). Have tried updating drivers automatically and uninstalling it etc. Need it to work on the lap top so it can act as the movable screen for it?
View 29 Replies View RelatedHard Drive Failure While Making USB Bootable Windows 7 - DRMK Error
Aug 28, 2012My system is Dell Inspiron 17R SE (7720), 1 TB Hard Disk 5400 rpm + 32 GB mSATA, 8 GB RAM, 3rd Gen i7. I was trying to make a bootable USB flash drive for windows 7 from Windows 7 Home Premium Reinstall disk that came with my Dell laptop, using the WinToFlash utility. But in starting the process, the PC froze, all applications (even explorer.exe) stopped, and Alt+Ctrl+Del refused to work. I turned the laptop off and back on, where it refused to even show the OS list and showed a DRMK message instead with a command prompt C:> as:
Loading DRMK V8.00...
DRMK Version 8.00
COMMAND.COM Build 37 - Jul 28, 2008
DRMK KERNEL Build 15 - Aug 8, 2008
Copyright (c) 2006-2008 Dell Inc. All rights reserved.
C:>
I tried booting from Windows 7 reinstall DVD but none of the repair options worked. I tried reinstall and repair options but my Hard Drive did not show up. It rather asked to Load Drivers for the Hard Disk. However, it did show any of the USB drives I connected to it, along with an X: drive, which must be the recovery drive for Dell's factory restore. I tried looking for Hard Disk drivers in that but no luck.
Then I downloaded from another PC a USB utility for Seagate Hard Drives from Dell website that makes a bootable USB. I ran that utility and it showed all the test passed (But there was no firmware update during the tests). Another thing I tried was using list disk command on command prompt in Windows Repair, but It did not show any drives, not even the X: drive. It only showed the USB drives I attached to it, or the DVD drive in list volume command.
I cannot boot to windows, I cannot install new windows, I cannot repair the windows and I cannot even factory restore my laptop. The hard drive shows up in BIOS, but not in Windows Boot or Windows Installation. Is there any way I can get my Hard Disk back without losing data? I have two partitions of that drive. I don't care about formatting C: Drive (Windows) but I wanna preserve E: Drive (the one filled with personal data but no programs).
Computer Doesn't Start Can't Get Into Bios Or Advanced Start Up Setting
Sep 17, 2012When i got home today didn't my computer work, my girlfriend has been the last one using it. So don't know how things were just before the shutdown or anything.when i turn on the computer i get to the screen where "touch bios" is and where i can see the options like Bios settings, boot menu, xpress recovery.but i cant press anything, and after about two seconds on that screen the PC shuts down again.The keyword lights up so there is a responds on it, but just doesn't work to press anything before it shuts down.I've got BSOD upto several times a day for a few months time.believe that my computer is affected by some virus or something is delaying my computer. might be an combination of several things.I got no external things hugged up to the stationeer computer right now.it is a windows 7 x64 machine.
usually when i get issues i can access advanced boot up or bios, but can neither in this case..I wonder if it might be a hardware issue.
Device Cannot Start
Jun 19, 2011Microsoft Teredo Tunneling Adapter
View 1 Replies View RelatedDevice Cannot Start Code 10
Oct 16, 2012I am getting this error in device manager over and over and over, i have uninstalled the driver, and reinstalled it over and over, i keep getting the same error, my hauppauge colossus card was working perfectly then all of a sudden i get this error, i have used ccleaner to repair my registry all to no avail, I think i need to do something in the registry to fix this but have no idea exactly what. What do i do?
View 12 Replies View RelatedDevice Cannot Start Code 10
Jan 12, 2013I have a Nikon Imaging scanner which my PC detects on connection. I have the correct driver which device manager installs with a code 10 error, the device cannot start.My PC is running Windows 7 64bit. I should point out that the scanner works correctly on my old PC running Windows XP, so there is no problem with the hardware. Anyone got any ideas why I might be getting the code 10 error on my new PC?
View 6 Replies View Related
