Flashing Cursor On Boot?
Nov 9, 2012
Wonder if anyone could help or provide some ideas.I'm trying to get my spare laptop to work.Every time I turn it on it just boots to a flashing cursor on a black screen.The hard drive in it is new - without windows 7 installed yet.I've tried booting from my windows 7 disk. Set optical drive to first in boot order. Just goes to flashing cursor, does not say "press any key to boot from cd" Tried booting from usb. Set usb hard drive to first in boot order. same as above.Mem test says ram is ok, reports cpu and ram amount in bios ok Laptop is hp compaq nc6320
View 5 Replies
ADVERTISEMENT
Nov 5, 2012
I was watching a football game on firstrowsport.eu and my computer (a hp pavilion desktop) just shut down uncommanded. I waited for it to restart, and after the BIOS screen, it just had a flashing cursor. I used the disc version of PartedMagic to get into my computer and ran the fdisk-l command. [code]
View 10 Replies
View Related
Oct 5, 2011
First off I have a Dell Inspiron n7010 system running Windows 7 Home 64bit
OK the other night I shut down my system and all seemed fine until next day. I went to reboot and got the normal Dell splash screen with both the Set Up (F2) and Boot (F12) options. After the Dell screen finished it then went to load Windows, but instead I got a Black Screen with Flashing Cursor. Can't move cursor at all.
On the Dell screen I can access the Set Up (F2) bios pages. I can also access the Boot Options (F12) Page. What I can not gain access to is the Restore (F8) menus.
I did not know to make any sort of boot disk or boot repair disk so I do not have either of these and I do not know of anyone who is using windos 7 that could make me one to use. Also Dell puts the rstore on the hard drive so onlyhave a MS Works CD and a Drivers & Utilities CD l ran the diagnostics utility but forgot to plug in my computer so when it was almost done the battery must have died so will redo the test later as tired tonight as been up half the night with this issue. But for memory the first 6 of the 8 memories areas it was scanning tested fine. Will post an update later today when Iget chance to run the whole thing again!!
I know others have had this screen. Is there a solution as have spent the last day or so googling it and seems very mixed results depending on the user and their own case with this black screen w/cursor.Some have said bad hard drive (I HOPE NOT THE CASE FOR ME AT LEAST!!!) Some have said bad mother board. Some have said virus or malware Some have referenced a software update both Microsofts and also specific computer companies. So what can I do to get to my files at least to back them up that is providing the drive is OK! I do know from the boot menu my hard drive is showing in the boot menus. Does this mean that the drives OK but maybe a corrupted boot area or something?
View 9 Replies
View Related
Feb 20, 2011
System is Windows 7 home 64 bit with amd athlon II 255 Processor 3.10 GHz and 4gb of ram. Avast anti-virus. I have windows firewall on, but haven't really made any other changes.My cursor flashes the busy symbol about once every 4-5 seconds, and it does so whenever the mouse is on the desktop or anywhere it shows the regular icon. When inside this text window it changes to the text cursor and ceases to flash, however. I changed the icon only to have the new one act the same.
View 28 Replies
View Related
Aug 11, 2011
my son has a toashiba satellite pro L450D-12x it goes past set up screen then to a blank screen (in black ) with a flashing line in the left corner how can i get it to load properley? before it did this it said media cable fail or something like that and i restored bios back to restore settings and it was also turning itsself off now and again.
View 12 Replies
View Related
Nov 8, 2012
I am having trouble with my Toshiba Sattelite MG45. When I turn it on, I get a black screen with a flashing cursor. I have tried the F8 method, nothing happens. Also, I am running Windows 7 with an Intel Core. I am by no means tech savy.
View 2 Replies
View Related
Feb 15, 2012
system goes to a black screen with a flashing cursor.
View 1 Replies
View Related
May 29, 2012
Ive had this computer for about 5 years and recently it has started to boot up really slowly
It goes through post like normal and then hangs on a black screen with a blinking cursor in the top left for up to 3 mins (maybe more, i didnt actually time it) before the windows 7 splash screen comes up I rarely re-start my computer, but now when i do im always afraid that it wont start up with how long it sits at that screen
The stuff ive found in searching about it has been about computers that dont boot at all when they have this screen, so im worried that will happen to me Ive also found that it might be the MBR being damaged, but in all those cases the people with that problem have more than 1 OS installed, i only have 1 installed
I would just do the steps to repair the MBR but i want to make sure there isnt another/better solution before i do
The computer runs fine other than this problem I've never formatted it (i know i probably should after 5 years but i dont want to) I didnt know where to post this sort of thing, debugging seemed like the best choice
View 1 Replies
View Related
May 26, 2012
I'm having an issue with my mouse's cursor constantly flashing the loading sign (blue circle) over and over. It only ever stops if I mouse over something that changes the normal cursor picture.
It started happening after my computer just froze randomly while playing Dota 2. I had to manually shut down the computer and when I turned it back on that is when this problem started happening.
Also, I can't do a system restore (as far as I know) because I had savepoints turned off before the issue so there is nothing to restore to.
View 7 Replies
View Related
Aug 15, 2012
I have an Acer aspire 5733-6607 with Intel Core i3 CPU 2.40GHz.
My mom was on it playing a game on the internet and stepped away to wash dishes when she came back it was on the black screen with the blinking cursor in the top left corner. I tried system repair disc, the recovery disc that it had me make when I first got the laptop and windows defeender offline nothing worked. I tried F8 and it goes to the black screen with acer and where I can press F2 or F12 and then back to screen with blinking cursor. I tried restoring default settings in the F2 menu also.
View 2 Replies
View Related
Dec 23, 2011
My computer was working fine a couple days ago and all of a sudden got a terrible Trojan that would spam me with random IE ads. So I ran ad-aware and it got rid of the problem. I went to bed relieved but woke up to my computer in a black screen with just a single cursor "_" flashing. I figured it was a fluke and restarted. same problem.
So I decided to open up the computer and check the SATA drive connections. Everything looked fine but the problem still persisted. I decided that it could just be slot number 1 and moved it to slot 3. The computer would start up and go to desktop but all of my icons disappeared and the computer would just hang if I tried to open any file or go on the internet or any program.
Obviously, it was because the SATA drive was now in a new slot?? I'm not sure. But I put it back into slot 1 and went into the BIOS setup and sure enough, it was a "not detected" for slot 1. The main HDslot.
I tried to reset the BIOS using the jumper method and it still just hangs on black screen with cursor "_" flashing...
Specs:
- windows 7 ultimate edition
- Intel duel core @ 3.2ghz
- 4gb RAM
- Asus P5Q-PRO motherboard
- geforce 8800 GTX graphics card
View 14 Replies
View Related
Aug 11, 2011
Have my Dad's Fujitsu Esprimo laptop to uninstall Searchqu, Bandoo etc for him which were causing problems. That went fine, computer shut down and tried to install Windows updates. Now won't restart.Hangs on Fujitsu screen with options for "<ESC>: Diagnostic Screen, <F2>:BIOS Setup, <F12>: Boot Menu" and Blue progress bar. Progress reaches about 75% complete VERY slowly (hour) but then hangs on black screen with white cursor in top left corner. Been like that for 2 hours now.Have tried solutions from Google - click F2 then re-setting boot order in Bios to "default order", click F12 and choose different options, tried F8 for safe mode, but F8 doesn't do anything.I don't know if it's related to Searchqu, to the updates or if it's just a creepy coincidence and the computer itself is actually broken. He doesn't have a Windows7 installation cd.
View 5 Replies
View Related
Oct 10, 2012
Earlier this week my HP desktop forced shutdown while browsing the Internet using IE9. Upon reboot the HP screen loaded, afterwards a black screen with a flashing cursor appeared. I had used CTRL+ALT+DEL function in which my computer rebooted.Showed the HP screen and immediately showed the black screen with a flashing cursor. Again no mouse cursor was available. I performed a diagnostics check in which the CPU, HDD, etc. checked out, restored BIOS to factory settings, even placing the HDD as priority 1. I inserted the Windows recovery disk and attempted a start up repair, and a restore point with no favorable results. Through the recovery disks command prompt I accessed all my music and documents, so I assume the hard drive is still functioning. I'm thinking as a last resort of performing a repartitioning of my hard drive and performing a clean install of Windows 7.
View 2 Replies
View Related
Jul 15, 2012
Recently I got this problem on my Acer Aspire 5742G where my laptop gets stuck on black screen with a flashing underscore at the top left corner right after the Acer splash screen. I can get into Bios but I can't get into safe mode (normally I could press F8 to get into Advanced Boot Options but this no longer works).
The problem started when I decided to try out Windows 8 Preview a few days ago. I managed to set up dual boot windows 7 home premium/windows 8 preview and it worked fine. But I only gave 20GB to the windows 8 partition and I decided I needed more. I thought it's a simple matter to transfer space by shrinking the volume of the win7 partition, format the new unallocated space and extend the volume of the win8 partition. But after I did this, all the partitions apart from the recovery one became "simple partitions" instead of "primary partitions". I don't know the difference between the two terms and I didn't think it was a problem so I just turned off the laptop once I finished with it. The next time I turned it on the problem started. Could this have caused problems with the hard drive? It's the only thing I can think of that caused the problem.
Unfortunately I can't find my recovery disc either.
View 5 Replies
View Related
Oct 6, 2012
my dell computer xp windows 7 when i try to boot up it will just get to blue screen but does not bring up accounts or allow to boot up any further then blinks or flashes blue to black screen and back. I can boot in safe mode and i have scanned computer with mal-ware, mcafee, and eset scanner . have not found a virus. I did lose the ability to watch you-tube videos, and the last error i got was adobe crashed. i don't know what to do from here. I have windows disk and thought about booting from it and doing a system repair but when i put that disk in i do not have the system repair option just an installation option.
View 14 Replies
View Related
Nov 19, 2012
When I get to the splash screen it just blinks. It won't boot. I've tried going into the safe mode by pressing F8 at the previous screen. I've tried booting from a start disk. It won't go into the advanced boot options, and booting from a disk made no difference. This has happened before but I was able to get in through safe mode. Once I get in I can do a system restore and it will work for a while. How can I get in to my machine?
View 3 Replies
View Related
Jul 4, 2012
I have just bought a new ssd for my desktop and have winodws running on my old 500GB hard disk.I installed windws 7 home 64 bit on my new ssd and have winodws ultimate on my old HDD.I the booted it from my ssd and it ran fine then I formatted my HDD with the old winodws using mini-tool Partion and had to restart to format. The HDD did have a system restore Partion but my ssd did not, now when I boot from my ssd a white line just shows up In the top left corner.I have Tryed windows startuP repair but no luck.
View 3 Replies
View Related
Nov 30, 2012
I wanted to install more RAM, but Supermicro support told me I needed to update BIOS (flash it) to enable it to accept higher RAM.After I did this, the BIOS seems to have lost the record that boots my Windows 7 installation. After going through the checks, it just comes up with "Operating System not found."So I thought that, since I have two SATA drives, I could try installing Windows on my redundant disk to see if that might generate a dual boot menu.I was able to successfully install a fresh copy of Windows on the 2nd disk, but it will only boot into that one. It seems my system has completely forgotten about my other, working, installation.Is there a process for recovering the boot information and setting it up such that I can go back to using my other installation?
View 2 Replies
View Related
Dec 11, 2011
Attempted to run chkdsk after Windows Update failed. When I restarted computer to run chkdsk, I got the black screen with the flashing "_". No pointer, if I push crtl, alt, delete, it just attempts to reboot. No other key does anything. I have removed the battery, unplugged the computer, but still get the same results. I am unable to get any boot options when pressing F8. Unable to boot from Repair disk, either. Ran diagnostics in F12, which showed all fine
View 1 Replies
View Related
Mar 4, 2011
About a month and a half a go my laptop was infected with 2 trojan viruses and ever since I haven't been able to start it up as it stays on a black screen with a blinking cursor after the toshiba splash screen. I am able to use my computer by booting with Hiren's boot cd and have since cleaned up my computer and gotten rid of any viruses..but have to continue booting via disc and it is getting sickening to do so.
View 3 Replies
View Related
Nov 3, 2011
I built my own computer last year. The computer boots up just fine but before it bios screen comes up there is a blinking cursor that runs for almost 20 seconds and then bios kicks in and everything goes on normally form there.
View 3 Replies
View Related
Aug 3, 2011
I just rebuilt my computer, but reused my old WD HDD, OS and all. It used to be hooked up to an AMD rig, but my new CPU is an i5-2500k and mobo is an MSI P67A-GD53 (B3). So when I hooked everything up and booted for the first time, the computer showed an error saying that the memory or cpu had been changed and that I needed to run the setup, which I did. That led me to the blinking cursor on a blank screen.It stayed that way for several hours before I decided to reboot. That time "A3" "99" "B4" flash on the screen, then it goes straight to the cursor. So I decided to give a new hard drive a try. I went out and got an SSD, hooked it up, same problemMy best guess right now is that the mobo was DOA. I'm still kinda new at this PC building thing
View 7 Replies
View Related
Sep 19, 2012
I started IT for a company a couple weeks ago. I get this tower with no idea what OS is installed.Is there a file that I can load through Trinity Rescue Kit that will tell me what version of Windows is installed on the system?
View 2 Replies
View Related
Jun 6, 2012
So I installed Windows 7 on my HD. The installation process went well. I chose my Username, password, etc, and then Windows prepares the Desktop for the first use, and then the PC automatically reboots.
The problem is that when the pc reboots after the final stage of the installation, Windows won't boot up and I get stuck with a blinking cursor. The only way I can boot up is when I turn on the PC and keep pressing F5 and then it takes me to a GRUB 0.4.4 Red Window like this one
When I chose the "alternative method", Windows boots with no problem. Is there a way to choose the alterative method as the default?
View 5 Replies
View Related
Jul 29, 2011
I have been getting an alert that I have updates to windows 7, but they never seem to actually install. Tonight it didn't seem like my audio drivers were working anymore.On my other computer I realized that Custopack tools, which is a theme customization program that alters uxtheme.dll, wasn't working with the new service pack. So with this laptop I restored the default windows theme and rebooted, and got my audio back. However, I went to shut down, which would also install the update, and when I booted back up, Windows won't even start.I get past the bios, and then there's just a blinking cursor. The door on the CD-ROM works but the caps lock and num lock do not.
View 2 Replies
View Related
Apr 30, 2011
I used to have win xp installed after which i decided to try out the win 7 so i installed it on another HDD. After thhe install everything worked fine so i decided i can format the drive on which xp was installed before. Althought win 7 did let me format it because it was a system drive ( the old xp drive) i used some other tools to get rid of it thinking i can just do a fixboot and restore win 7 boot files. Now that the old system partition is gone win 7 wont boot, all i get isa black screen and a blinking cursor. I tried to boot from the win 7 dvd and do startup repair but still get the same issue.
i really dont want to reformat win 7 and install it again?
View 1 Replies
View Related
Jan 8, 2012
I use an Asus Bamboo U43 series running Genuine Windows 7 Home Premium x64. I was using it as usual and what I thought was a normal update occurred. When computer went into a typical update restart, upon reboot a black screen with a blinking cursor appeared (normal for start-up I know) but then the cursor dropped down a few lines as a cursor would do if you hit enter a few times, and that is it. The computer will not continue to the windows start-up screen. Pressing F8 or F9 during reboot does not respond. I can us ESC or F2 options and that is it.
View 9 Replies
View Related
Oct 20, 2009
I have a problem when booting up Windows 7.
When I boot, I see the 4 particles, but after that, i get a black screen with my mouse cursor, but that's all.
If i wait for about 7 minutes, i get the login screen and everything works fine.
I haven't installed anything or done anything that could cause this.
Is this normal? I hope not because i hate waiting :P
I have read some other topics that seemed to be almost the same problem as mine. Some say you have to get a new videodriver. have done that, didn't
work. Restoring to a restore point didn't work either.
Any suggestions?
EDIT: Forgot to say, it is a dual boot (win xp/win 7) (maybe usefull information)
View 9 Replies
View Related
Mar 20, 2012
I'm having regarding my Dell with Windows 7 x64. Initially I got the message "Loading PBR for descriptor 2... Done". That's all it said, and did not continue to boot. I researched the error message and found many users with similar problems that solved it by booting the Windows 7 dvd and running bootrec.exe from the command prompt, so I attempted this. I tried bootrec with the /fixmbr, /fixboot, and /rebuildbcd options. After trying to fix my problem with bootrec, the "loading pbr" message no longer appears, all I get is a blank screen with a blinking cursor after the BIOS. I'm not sure what the problem or solution is at this point. I'm not sure if I've made things better or worse. I tried running chkdsk /r but it won't run, complaining that the disk is write protected. Edit: I just realized that System Recovery Options is showing "Operating system: Unknown on (Unknown) Local Disk"
View 3 Replies
View Related
Jul 11, 2012
My laptop (Hp Pavilion dvx4 1 1/2 years old) suddenly won't load Windows 7. It turns on, fan and DVD drive run but the mute and Internet icons on the keyboard remain red and there are two flashing lights on the keyboard (one beside the caps lock key and the other is above the scroll key). That's all it does. No beeps, sounds or cursor. I had noticed a problem with my sound on a couple web sites prior to this but no error messages ever displayed indicating any problems. I bought this laptop at Best Buys and they installed a recovery disc but other then that I don't have the original Windows 7 disc in order to try to boot from CD-rom.
View 6 Replies
View Related
May 12, 2012
Been having 9 RootKit issues popping up on our Laptop found by the AVG scan for about a month now. I wanted to just do a complete Restore to get things running normally again. Problem is I have a huge amount of pics on there that are not backed up. Been trying to come up with a quick & easy way to do it.Did a Google search the other day & read that I could use a Bridged USB-USB cable & transfer the pics to our PC. Went to Best Buy to get it & they told me that the Belkin Easy Transfer Cable would do it. Well, I attempted to run the thing last night (I don't think it was even doing what I wanted) and now the laptop will not boot at all.There was an error message (that I didn't write down) on it when I got up this morning & now all I get is a black screen with the arrow cursor on it.
View 14 Replies
View Related