Okay, so I'm ripping my audio CDs, and I just had a problem getting the drive to open, So I looked and saw a tiny hole on the drive, I stuck a paper clip in it and it opened.
Now however I cannot get it to detect any CDs. It will not load anything. Now I looked and I realized that my CD/DVD drive was not listed on my computer. I am trying to figure out what driver I had, so I can try re-installing it. I run a Dell Inspiron M5010 64 bit.
I'm ripping my audio CDs, and I just had a problem getting the drive to open, So I looked and saw a tiny hole on the drive, I stuck a paper clip in it and it opened. Now however I cannot get it to detect any CDs. It will not load anything.Now I looked and I realized that my CD/DVD drive was not listed on my computer.
View 3 Replies View RelatedI have one hard disk 150GB on my computer. I want to install Windows 7 and divide the drive into two partitions. When I did it using the instructions that I had during setup, Windows 7 load only with the system drive! Where did all the other memory gone? Can I return the lost memory without installing again Windows 7?
View 2 Replies View RelatedI'm trying to fix a vaio laptop at the moment and am a bit stuck. The screen doesn't go past the vaio. It just before the windows logo would normally appear. I tried using the windows 7 cd to try a repair or cmd/chkdsk etc, but the OS wasn't found/listed. I also tried to do a clean install and the HD wasn't detected by windows 7 setup. I also tried booting up with ubuntu and the HD still wasn't detected. Can I assume this is a busted HD? Should I still shoot for a bootage diagnostic cd for the hard drive?
View 1 Replies View Relatedhave two hard disks in my PC one is IDE(120GB) and the other is IDE(60GB). My PC is not detecting my IDE(120GB) hard disk. I have been replaced my jumper cable but it still not recognizing
View 1 Replies View RelatedLogitech usb hub is not detecting external hard disk seagate 320 gb fr. i have windows 7 ultimate 64 bit while connecting external hard disk directly to usb port its working but when i connecting this hard disk using logitech 4 port usb hub on the same usb port its not detecting but my pen drive is working through usb hub.
View 2 Replies View RelatedSo recently my desktop PC has been freezing at random times, and then sometimes restarting after not responding for a couple of minutes (no BSOD, just restarts as far as I've seen). It sometime freezes as soon as I turn the computer on, while Windows is loading, and sometimes it will start freezing after an hour it's been on. Most of the time it will just freeze for around a minute, and then unfreeze, but sometimes it does freeze and then restart. By freeze I mean everything, mouse included, and ctrl+alt+delete doesn't work.Also at bootup sometimes, it will fail to detect my SATA hard-drive and hang at Detecting SATA drives at the bios screen. This will be following by a disk read error.This problem started occuring a couple of weeks a go, so I reinstalled Windows 7 and it worked fine after that.
Running Windows 7
Bios: Phoenix - AwardBios v6.00PG
Processor: Intel Core2 Duo CPU E6550 @2.33GHz
2GB RAM
Graphics Card: Nvidia GeForce 8600 GS
The bios is detecting all of them but Windows 7 is not. The floppy's power is on all the time and it is enabled in the bios. My 3rd hard drive is not being detected, however I did delete some windows 7 files and it was working before that. And I have no idea about my dvd drive. My other drive is working though.
View 1 Replies View RelatedI gave my pen drive to my friend she used it in internet cafe but it doesn't working from that day.it is not showing in my pc when i insert into my laptop
View 1 Replies View Relatedone day i was playing mafia ii and all of the sudden everything stops my desktop was empty error message everywhere my pc couldnt find my hard drive . i used sistem restore now every picture and all my music is gone
View 4 Replies View RelatedI'm installing a fresh copy of Windows 7 Ultimate on an Asus UL80J. When asking where I want to install windows, I get "No drives were found. Click to load a driver". The drive is new, has no problems, and is detected in the BIOS fine. Also, my Windows XP CD detects the drive just fine. I've tried both options in the BIOS for setting SATA to IDE and AHCI. I assume I'm missing a SATA driver needed at installation time, but I can't find one online or from the manufacturer.
View 8 Replies View RelatedIm upgrading to windows 7 on a new hard drive and it will not detect my seagate hard drive?
View 9 Replies View Relatedi just built a computer today. and its the famous windows 7 not detecting hard drive but first here is my set up
amd fx 4100
gigabyte 970a-d3 mobo
kingston 4 gb ram (1 stick)
WD 500gb hard drive
now its the famous install. everything is brand new the new computer can not get any updates its not hooked to the internet, nor do i have a flash drive im on a crappy laptop right now that is surprisingly not fried yet, so i cant do anything updating yet, all i want to do is install windows 7 to my new pc, but it says no driver found, ive even tried putting in the mobo disc like gigabyte said to and still nothing. what can i do? my bios recognizes my cd/dvd rom drive and it also recognizes my hard drive. its all there. but windows 7 wont. is there something in the bios i need to change, i called microsoft and they told me i needed to reformat my hard drive but wouldnt tell me how, gigabyte told me the same thing and the computer store where i bought all my stuff wont touch my computer unless i give them $41 for diagnostics and $41 for install, the guy there is rude and doesnt seem to care about customers who made a HUGE purchase 2 hours before. everybuddy is saying update this update that but i cant the computer has no OS. it has boot screen, bios and windows install.
my pendrive name is cruzer edge 8gb it detected in my computer but i can't use it properly.
View 1 Replies View RelatedI soon as I play a dvd it stops workig & optical driver not detected, needs dvd decoder.
View 1 Replies View Relateddell laptop not detecting pen drive?
View 2 Replies View Relatedmy pc was running fine but suddenly it switched off on its own, as if there was a power failure (it might have been due to a virus cause i just then had downloaded a file that contained a exe file that shut up my anti virus... but i've never heard of a virus killing hardware) on restart after the windows startup screen, a blue screen flashes and restarts again ..startup recovery doesn't work either .. when i try reinstalling windows using the disk . it doesn't detect any hard drive.i've tried to remove all the components of the pc and reconnect them but it still doesn't work.
View 11 Replies View RelatedI recently bought a SSD (Solid State Drive) it is a Samsung 64GB. My computer is an Asus with an i5 Processor.
Anyway I know the SSD works fine because currently I have Ubuntu downloaded on it, running just fine. For some reason however, Windows 7 is not detecting my drive. Under my computer, or upon booting from a disk, it will not detect it. The reason I am wanting to detect it, is because I would like to backup windows 7 onto my SSD and boot from there.
I installed Windows 7 64-bit on my computer which has only 1 hard drive (640GB). I partitioned it using XP to have 4 partitions: 1) XP Partition 2) Linux Partition 3) Linux Swap 4) Windows 7.The problem is Windows 7 cannot detect any partition besides it's own partition, so I cannot access any of my data from the other partitions (XP and ubuntu --- I don't care about ubuntu but I need the data on the XP partition). I know the other partitions exist since I can access XP still, and I believe XP can detect all 4 partitions.I went to start->menu then searched for partition and selected "Create and format hard disk partitions" and it actually detected all the partitions. The problem was the other partitions did not have drive letters associated with them.So I just right clicked and changed the drive letters.
View 4 Replies View RelatedI recently built a new computer and connected my old hard drive to copy files across to my new one. Both drives had Windows 7 installed and while staring up I had to select one to boot from. I have since removed my old hard drive but am still asked to select one to boot from even though there is now only one connected. How do I remove my old hard drive so that it will automatically boot from the new one?
View 8 Replies View RelatedI'm installing the official MS downloaded 64-bit build 7100 RC (released May 5). I'm installing onto an Athlon 64 X2, 4 GB RAM, etc. I have integrated graphics card that I'm using to get it running, before trying to get my ATI 4670 to work. The int. graphics card is an ATI X1250 chip.
When I just boot it, everything loads fine, but the Windows screen is mostly white with black lines through it. You can see where textboxes are, but not what's in them. The mouse cursor is fine throughout. So, I figured my drivers were just bad.
So, I tried to load the system via the Windows 7 boot disk, then go to the Repair Windows option. This all works fine and the screen looks normal. I open up the folder with my drivers (downloaded directly from Gigabyte today), and select my .inf file. It brings up a list of drivers to install. I click on my chip (again, the X1250), and it loads for a bit before saying the driver failed to load. So, I don't know what I'm doing wrong here other than just being SOL. Any thoughts?
I purchased Dell Inspiron i14z Ultrabook, it has a hybrid SSD, it have 32gb SSD and the rest 470gb hard drive. It had Windows 8 and I couldn't stand it...I changed the BIOS settings from Intel Smart Response to AHCI, used Wipe Drive, (which detected the hybrid SSD as two separate hard drives) to format both hard drives, installed Windows 7 on the 32gb Hard Drive (I assume this is the SSD part), and everything went great.But when I click MyComputer, it only shows 32GB as my hard drive, how do I set the settings where it would show the rest of the hard drive that is not SSD?Whenever I change the AHCI setting back to Intel Smart Response Technology, it gives me a brief Blue Screen of Death briefly, then restarts in a loop.
View 1 Replies View RelatedI recently upgraded my computer and part of the plan was to use two 2Tb drives in a raid setup for my main windows drive. I see that it only recognises about half of the raid volume and the rest is unallocated space. Is this a general limit on Windows or is there a work around this?
View 4 Replies View RelatedI'm at my wits end now though, After several attempts at installing Win 7 RC (64bit) I realised it wouldn't let me becasue I hadn't added the latest drivers for my motherboard. Now it appears to have installed but whenever windows starts, it reboots at the point where the first 'red dot' appears (the four colours swirl in to make the window).
I ran in safe mode and it appears to reboot whenever it gets as far as 'system32/drivers/disk.sys'
I have installed to three different HDD, both IDE and SATA. All clean before the start. I've used an IDE DVD drive and a USB external, and my BIOS is totally up to date. I've now striped the PC of everything none essential.
The latest drivers for the motherboard are the Vista 64bit variety because there are no windows 7 drivers (that I could see).
P.S. I also obtained a copy of the 90day release version of 64bit Ultimate, which a friend has successfully installed on his Vista laptop. I've tried installing this with all the same configs and same problem every time.
Just purchased Windows 7 oem, when I insert the CD the system doesn't see the disk in the CD drive.I've just installed a fresh install of Windows XP without any issue. Everything is operating correctly on my system.AMD Athlon 1.11 GHz Processor150 GB RAM 32 bit System board
View 5 Replies View RelatedDisk read error ctrl+alt+dlt to restart your system.
1. Have sony vaio E-series vpcea23en
2. Fail to load windows 7
3. Even recovery dvd stop to load
4. No option in bios to run diagnostics.
5. Try to install windows 7 64bit clean install but also failed to load it.
6. Have no money for new hdd.
7. How can I format my laptop. full
I have a Dell XPS 430 that came with Windows Vista and a Windows 7 upgrade disk. I set up my main hard drive with Windows 7 on one partition, Linux on another partition, and a third partition for storage. I recently needed more space for Windows, and no longer needed Linux, so using the Windows 7 disk manager I deleted the Linux partition and extended the Win partition using the newly unallocated space.
Upon restarting my machine, I am no longer able to boot into windows but instead am presented with the message:
GRUB Loading, please wait...
Error 22
I have a Windows 7 disk that I am using to access the repair utility, which I have run countless times. I have tried severel of the tutorials to rebuild BCD and FixMBR, etc etc. Frankly I am getting lost in all the commands and not even sure what does what anymore!
main problem on this computer is thats it a windows XP motherboard trying desperately to run Win7. It can to a point, but is having issues as Win 7 improves etc. etc. Now my gaming rig is Win7 has a far better graphics platform but has a small C drive. Initially it ran Rfactor (online car racing, and I organize races for a team of guys, we do this weekly and consequently I have several other related programs) and that was all it was going to run. So since then another group of us play BF3 and I've always liked the golf games so I ported those to games across to the gaming rig - hence the reason they are on another drive. I could get another larger drive and start again from scratch but it is to damn awkward at the moment because of the racing season has started. Obviously there is a problem with TW writing log files to my I: drive but I would have thought Origin Had thought of that when they are saying that you can install the game on another drive (other than C: Drive)
View 8 Replies View RelatedMy C: drive seem's corrupt. Can't boot my win7, neither in safe mode. Did try to repair my version 64 with the installation disk, no luck, same problem.
How can i do a repair disk on the drive like chkdsk on it. Is there a tool in the installation disk?
I just moved my Windows 7 partition to an SSD. While everything loads much faster, I still hear the mechanical drive being accessed on the boot logo screen and for a few seconds after the desktop appears. I have the page file, temp folder, and other system stuff all on the SSD. The only thing I think it should access on a mechanical partition is the wallpaper, but that's 2 MB max. Is there a way to have Windows log all of the files that are being accessed during boot?
View 3 Replies View RelatedI am loading windows 7 on my PC. Keeps on saying cd/dvd drive device is missing.
View 1 Replies View Related