Loading Drivers Via Win 7 Disk Boot
May 5, 2009
I'm installing the official MS downloaded 64-bit build 7100 RC (released May 5). I'm installing onto an Athlon 64 X2, 4 GB RAM, etc. I have integrated graphics card that I'm using to get it running, before trying to get my ATI 4670 to work. The int. graphics card is an ATI X1250 chip.
When I just boot it, everything loads fine, but the Windows screen is mostly white with black lines through it. You can see where textboxes are, but not what's in them. The mouse cursor is fine throughout. So, I figured my drivers were just bad.
So, I tried to load the system via the Windows 7 boot disk, then go to the Repair Windows option. This all works fine and the screen looks normal. I open up the folder with my drivers (downloaded directly from Gigabyte today), and select my .inf file. It brings up a list of drivers to install. I click on my chip (again, the X1250), and it loads for a bit before saying the driver failed to load. So, I don't know what I'm doing wrong here other than just being SOL. Any thoughts?
View 0 Replies
ADVERTISEMENT
May 22, 2012
my laptop running 64 bit windows 7 started freezing. Restarting helped for about 10 minutes, then it freezes again. I looked at my system log and noticed a couple errors, the most serious of which said that these boot-start or system-start drivers failed toload:CbFSctxusbmdiscacheMpFilterNIPALKnipbcfknipxibafnipxibrcSolutospldrVBoxDrvVBoxUSBMonWanarpv6I'm currently running Malware Bytes and GMER in safe mode, and it's not freezing
View 1 Replies
View Related
May 28, 2011
I'm ripping my audio CDs, and I just had a problem getting the drive to open, So I looked and saw a tiny hole on the drive, I stuck a paper clip in it and it opened. Now however I cannot get it to detect any CDs. It will not load anything.Now I looked and I realized that my CD/DVD drive was not listed on my computer.
View 3 Replies
View Related
May 28, 2011
Okay, so I'm ripping my audio CDs, and I just had a problem getting the drive to open, So I looked and saw a tiny hole on the drive, I stuck a paper clip in it and it opened.
Now however I cannot get it to detect any CDs. It will not load anything. Now I looked and I realized that my CD/DVD drive was not listed on my computer. I am trying to figure out what driver I had, so I can try re-installing it. I run a Dell Inspiron M5010 64 bit.
View 3 Replies
View Related
Nov 30, 2010
I recently upgraded my computer and part of the plan was to use two 2Tb drives in a raid setup for my main windows drive. I see that it only recognises about half of the raid volume and the rest is unallocated space. Is this a general limit on Windows or is there a work around this?
View 4 Replies
View Related
Sep 22, 2009
I'm at my wits end now though, After several attempts at installing Win 7 RC (64bit) I realised it wouldn't let me becasue I hadn't added the latest drivers for my motherboard. Now it appears to have installed but whenever windows starts, it reboots at the point where the first 'red dot' appears (the four colours swirl in to make the window).
I ran in safe mode and it appears to reboot whenever it gets as far as 'system32/drivers/disk.sys'
I have installed to three different HDD, both IDE and SATA. All clean before the start. I've used an IDE DVD drive and a USB external, and my BIOS is totally up to date. I've now striped the PC of everything none essential.
The latest drivers for the motherboard are the Vista 64bit variety because there are no windows 7 drivers (that I could see).
P.S. I also obtained a copy of the 90day release version of 64bit Ultimate, which a friend has successfully installed on his Vista laptop. I've tried installing this with all the same configs and same problem every time.
View 1 Replies
View Related
Dec 20, 2010
I have one hard disk 150GB on my computer. I want to install Windows 7 and divide the drive into two partitions. When I did it using the instructions that I had during setup, Windows 7 load only with the system drive! Where did all the other memory gone? Can I return the lost memory without installing again Windows 7?
View 2 Replies
View Related
May 26, 2012
Disk read error ctrl+alt+dlt to restart your system.
1. Have sony vaio E-series vpcea23en
2. Fail to load windows 7
3. Even recovery dvd stop to load
4. No option in bios to run diagnostics.
5. Try to install windows 7 64bit clean install but also failed to load it.
6. Have no money for new hdd.
7. How can I format my laptop. full
View 7 Replies
View Related
Jun 6, 2012
I have a Dell XPS 430 that came with Windows Vista and a Windows 7 upgrade disk. I set up my main hard drive with Windows 7 on one partition, Linux on another partition, and a third partition for storage. I recently needed more space for Windows, and no longer needed Linux, so using the Windows 7 disk manager I deleted the Linux partition and extended the Win partition using the newly unallocated space.
Upon restarting my machine, I am no longer able to boot into windows but instead am presented with the message:
GRUB Loading, please wait...
Error 22
I have a Windows 7 disk that I am using to access the repair utility, which I have run countless times. I have tried severel of the tutorials to rebuild BCD and FixMBR, etc etc. Frankly I am getting lost in all the commands and not even sure what does what anymore!
View 1 Replies
View Related
Mar 29, 2012
im usin 2tb segate new hard disk sir..in my system i cant able to boot my os and also my hard disk...its showin that hard disk boot failure insert system disk press enter ...i restarted many times its sayin the same problem...in my gigabite mobo bios my hard disk is not get detected sir....the problem is that wen im installin the new os for 2nd time its all went nice only sir but at the completion of the os it wil ask for the user name and password but in my system its frozen sir fully of black screen and i cant able to do anythin so i restarted my system from that im gettin this error as hard disk boot failure insert system disk press enter.....that my new hard disk and all of my data is in that hard disk only..this problem arises wen im installing the os for 2nd time sir.
View 6 Replies
View Related
Jan 5, 2012
windows 7 disk boot failure insert system disk and press enter
View 1 Replies
View Related
Aug 27, 2011
I woke up this morning, and I found that my computer was displaying this message"Disk boot failure, insert system disk and press enter". There are a ton of needed documents on the computer, and I'm hoping that they can be saved some way.
View 5 Replies
View Related
Oct 13, 2010
I've been having this error even after reformatting and reinstalling Windows 7 on my desktop. I've done reformatting / reinstalling Windows 7 several times, yet the problem still occurs. I'm thinking of my HDD as being corrupted or messed up. The problem occurred after I accidentally hit the CPU when I was stretching my foot. The screen froze after that. Upon rebooting it, 'Disk boot failure, Insert system disk and press enter' occurs. After I entered the DVD installer of Windows 7, the screen just hangs.
View 9 Replies
View Related
Feb 17, 2010
I have been having a bit of trouble with windows 7 lately, namely that it won't start up right. When I boot from the drive normally, it gives me the classic "BOOT DISK ERROR: INSERT SYSTEM DISK AND PRESS ENTER" message.
However, I soon discovered that if I boot from the Windows 7 cd and do not boot from it (By ignoring the "Press a key to boot from CD or DVD..." Windows 7 boots up fine.
I've tweaked my BIOS over and over, but the same problem persists. The drive is brand new and fine. What can I do?
View 10 Replies
View Related
Jan 10, 2013
My friend bought a new PC and needed to put am OS on it. He put in the W7 disk and the error message 'disk boot failure insert system disk and press enter' appeared before installation was shown. He has tried changing around BIOS and it also recognises the hard drive and DVD/ CD ROM drive. Here is the specification he was given:Case : CIT Reaper Black Mesh fronted Tower CaseMotherboard : Gigabyte 78LMT Motherboard TechnologyCPU : AMD Bulldozer FX 4170 4.2ghz 8mb CacheHard Drive : 1tb Sata Hard DriveMemory : 8gb DDR3 1600mhz MemoryOptical Drive : 24x Dual Layer Sata DVD WriterGraphics Card : Nvidia Geforce GTX 650 2gb GDDR5 With HDMIPower Supply : 750 Watt Branded Power Supply Also, he has tried booting BIOS in different order
View 3 Replies
View Related
Mar 6, 2010
Just installed my new rig and trying to get Windows 7 on it. I'm using an Upgrade DVD from Acer 64-Bit, and trying to boot from the CD-ROM setting in BIOS or boot mode. I am unable to get past the "Starting Windows 7" screen with the logo. It just freezes there or loads and goes to a black screen. I don't have other OS DVD/CDs to try out other than the old Windows 7 RC I had a while back. That wouldn't load either. Now I tried to use a different DVD-ROM and it wouldn't load either. What could be the problem?
View 2 Replies
View Related
Sep 5, 2011
When starting the computer, I keep getting "Disk boot failure, insert system disk and press enter". Nothing works other than putting in the boot disk and hitting the restart button on the tower. Then it will boot up and run fine. But how do I stop it from having to have the disk in order to load? Checked in the BIOS and the hard drive is the first load.
View 3 Replies
View Related
Nov 15, 2009
Ok, so iv put this computer together, installed windows 7 Ultimate 32bit and i got it up and running perfect for like a day.
The next morning i switched it on and was working good for couple of hours then it seemed like the whole computer started to slow down and i got a blue screen error. so i rebooted and tried to start windows but, it then says windows is loading files then goes to the logo loading and after that it just goes to a black screen!? iv tried everything to get it back running safe mode, low res mode, repair, boot from disk etc but nothing.
So i thought i would try and put the HD in another computer and wipe it to re-install windows but when i put it in another comp it does the same thing.. does the logo loading and then to black screen
Iv found that when i remove the HD from my PC and boot from the windows 7 disk then it gets to the windows 7 installation bit so do you think it could be a problem with the HD?
View 2 Replies
View Related
Jan 21, 2012
Fresh installation on a raid 0 array and I am at the pre-load drivers step.I have no idea which drivers I should be loading here (if any)The RAID is 2x Vertex 3 120GB SSDs on an ASUS P8Z68-V PRO motherboard. (i7-2600K chip)I've done a complete install without pre loading anything and it all seems functional - except a couple weeks after install upon boot up it shows one of the drives in the array as Error Occured (0). Again everything is functional but still annoying.
View 2 Replies
View Related
Dec 9, 2012
I haven't touched this laptop in a while. I received a virus which then slowed down my computer and made it really really slow to get into the windows log in screen. It wouldn't go past that. Now, 2 months later, I'm trying to install Ubuntu as my only OS. I hope this will get rid of whatever past problem I had. Is this true? The problem with this, is when I power it up and turn it on, the computer only goes to the "Toshiba Leading innovation" H2 BIOS screen. From here, the laptop screen keeps turning black/blank at random intervals (the disk drive kicks up after it turns blank). The screen returns to the BIOS screen... and I keep hitting F12 and nothing.
View 4 Replies
View Related
Dec 6, 2009
So this is not the first box I've built but it is the first time I have not been able to boot easily for so long. The symptoms are that it hangs at the windows logo on the start screen, most times. If I do a safe boot, then sometimes it will boot successfully afterwards.
I can play Call of Duty 4: Modern Warfare, watch movies but opening a picture would cause a BSOD. I fixed the last symptom by reseating the card and installing the latest driver (195.62) while only the vga monitor is connected. It still hangs at the start screen though on a cold boot.
I have used the Windows 7 mem test to confirm it's not memory. I have then done a boot log (ntbtlog.txt) and I can see the following lines repeated as it tries and retries to load drivers:
Did not load driver @hal.inf,%acpi_amd64.devicedesc%;ACPI x64-based PC
Did not load driver @cpu.inf,%intelppm.devicedesc%;Intel Processor
... (more of the previous line)
Did not load driver @oem6.inf,%nvidia_dev.05e3.01%;NVIDIA GeForce GTX 285
This happened on the driver that came with the device too. I can tried repair installs and clean installs of my OS. I tried deleting the driver altogether and then letting windows load a driver for it and same result. Aside from sending the card into the manufacturer for testing, are there any ideas out there on what i can do?
Sadly, I am actually enjoying the challenge. Mostly because on the rare occasion I can boot normally and use my pc normally and leave it on for easy's sake.
View 9 Replies
View Related
Mar 10, 2011
Just after booting-up my system is prompting me that two dll files are not loading. I have investigated the necessity of the dll files and they have no relevance to the OS or anything I am using. How would I stop the system from attempting to load these files?
View 9 Replies
View Related
Nov 9, 2012
My PC goes through the BIOS stage and starts to load Windows 7, the GUI comes up and then it just stays there, goes into space with nothing happening. I have booted in Safe Mode and that works, but it won't boot into Safe with Command Prompt or Networking. I have tried the Repair my Computer option but that did not fix it. Then I did a System Restore but that did not fix it either. Not sure as to what to do next.
View 2 Replies
View Related
Sep 16, 2009
My problem is that windows 7 wont get past the loading screen when its loading the OS. I have noticed that it will work when i have only 2GB(one stick) in but when i try to put all 8GB(4 sticks) in, it wont work. This same thing happened when i was trying to install windows 7 from a fresh install.
View 9 Replies
View Related
Jun 23, 2010
I have sony vaio laptop and i was running windows vista on it. I did a partition and dual boot the system with ubuntu 10.4. Then i download easybcd tool to set windows vista as a default OS to boot with, but accidently in easybcd software i unistalled vista boot loader. now when i reboot the system ubuntu works fine but when i try to load vista its says NTLDR is missing Press Ctrl+Alt and Delete to restart. Then tried to boot from cdrom because i have a fresh copy of Windows 7. the system doesnt boot from cdrom. So now i am stuck with ubuntu on my system.
View 1 Replies
View Related
Jul 28, 2011
I like to use my mouse on the left side even though I'm a rightie, so I have the primary buttons switched. Unfortunately, Windows 7 loads that config almost at the end of the boot up process, which of course is annoying if you're trying to click on a few things while the boot finishes (and not knowing which button to use
View 2 Replies
View Related
Jun 10, 2010
I really want to go back to a dual install (Windows 7-64 Pro and Windows XP) but I want to add XP to Windows 7 which is already loaded. I know how to load Sata drivers when loading XP first (have drivers on CD) but after looking at the tutorial it mentions adding Sata drivers to XP using 3.5 disk. I do not have 3.5 drive. HP Pavilion a6130n/3 internal 1TB drives. XP and 7 will be on separate hard drives.
View 8 Replies
View Related
Dec 28, 2011
So, I need to know if I can install windows 7 x64 via direct boot when I start up my computer it is in ISO format. So like my default boot will be my DVD drive to install it. can I do that with it being ISO format?
View 12 Replies
View Related
Mar 25, 2012
I tried to add a new 1TB HDD into my computer. not realizing what i was doing wrong. i just threw it in there no software or anything. now my PC is getting "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" and i no longer have my windows 7 disk. is there anything i can do ?
View 1 Replies
View Related
Dec 7, 2010
Loaded 7Ultimate and got to Install screen. Selected drive and made new partition. Clicked next. Received error: Quote: Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more info. I don't know how to get to the logs, but what does this message mean? I have tried almost 6 or 7 times and even once with my 7 Home edition disk. Ran the startup repair a couple times. Tried formatting the drive from my XP Pro sp3 disk.So now here's where the real problem comes in: ERROR LOADING OPERATING SYSTEM. Now I can't get back into XP! Tried booting from ERD Commander 05, but I get an error code 4096 with that, and "File SETUPREG.HIV could not be loaded".How can I get XP back to booting properly? Maybe it's a faulty hard drive and needs returning. But it is extremely important that I get this computer back up and running immediately.
View 5 Replies
View Related
Mar 14, 2012
The first problem was that it kept booting into the windows startup repair. For a split second i can see windows 7 loading but then it automatically went to the startup repair , after many many reboots i opened the command prompt in windows startup repair and tried fixing the master reboot.Now it gets stuck at loading operating system.Even when i try to boot from the windows 7 CD and Truecrypt rescue disk it still gets stuck at loading operating system.The whole harddrive was encrypted with truecrypt and it use to go to truecrypt bootloader after loading the operating system but it doesn't do that anymore.
Specs :
mobo : Gigabyte GA-890FXA-UD5
cpu: phenom ii x6 1090t
gpu : radeon hd 6950
hard drive : western digital black caviar 1TB
View 2 Replies
View Related
