Computer frozen on restore systems after power outage. I cannot use disc 2 reboot - all keyboard actions frozen. All I want to know is - would I have lost what's on my hard drive and how to be able 2 get it running again.
View 3 Replies
my internet recently stopped working and my computer was freezing alot so a friend suggested to me it might be a virus therefore I should use system restore. I chose the restore date from about 5 days ago which was before 5 'critical updates' were installed. the computer has now been restoring for around 8 hours showing only the message " please wait while your windows files and settings are being restored. system restore is initialising..." I'm fighting the urge to turn it off and reboot
View 1 Replies View RelatedI am running Windows 7 Home Premium and attempted to do a system restore. I set the restore back a few weeks ago and then it began more than two hours ago. The screen says "Please wait while your windows files and settings are being restored. System restore is restoring the registry...". I know that I probably should not attempt to reboot, but how should I handle this?
View 2 Replies View RelatedI had a power outage a few days ago and went to turn on my pc again and it is telling me to install a OS cause now there is no OS so i tryed to format the hard drive and install a fresh copy of windows 7 64 bit but partition any of the 3 wont install on it and it tells me its the wrong format on one and i cannot change it..
View 1 Replies View RelatedI made the huge mistake of booting my custom built machine during a storm and as luck would have it, the only time that the power was lost (for about 2 seconds) occurred at that time. Now my machine will not boot. Startup repair comes up and tells me that it could not find the problem and I must shut down. I have tried restoring, mem tests, hard drive tests, reseting my mobo to failsafe settings, booting from the windows 7 recovery disk, booting off of the original windows 7 install disk, forcefully kicking it and crying. Nothing has worked, however. No matter what method I use, even when successfully completed, I am still faced with the startup repair error. I built the PC myself, so I'm not a complete fool when it comes to computers.
View 1 Replies View RelatedI am hooked up to a UPS, but after that runs out and I am away, I sometimes need to remotely logon - in which case I need the computer on. If I need to change something in the BIOS, please give specifics of how to do this as I have looked in there and found nothing related to this.
View 9 Replies View RelatedThis HP computer is running Windows 7 - 64 Professional, version 6.1, build 7601 Service Pack 1. The last time I had a normal start up was last Saturday after turning off all the computers and unplugging due to thunderstorm activity in the area. Yesterday morning, Sunday, we had 4-5 momentary power outages where the electricity pretty much flickered a few times, then stayed on. This computer did start up, but the start up process took approx 20 minutes.
I restored the computer to 3 days prior with no noticeable difference, ran defrag with no noticeable difference, and ran chkdsk, which did make a difference. The 1st start after the chkdsk was a normal quick start, then subsequent starts take approx 3-4 minutes, so it has slowed down again, but not near as bad as the original problem. The start up goes as follows:
1.) The normal Blue HP start up screen for approx 20 seconds, then,
2.) The windows graphic with the changing colored "windows" on the black background, then,
3.) a completely black screen for approx 2-3 minutes with minimal flashing of the HDD light, then
4.) proceed to Welcome to Windows screen where everything loads and the HDD light is pretty much steady. Within 30-40 seconds of getting to this point the normal desktop is up, icons are loaded, and computer is ready to use.
My step 3 noted above - the black screen, is usually 15-20 seconds max, so it seems whatever the hangup is is occuring during that time. After the start up is complete everything works normally. There isn't any abnormal use of memory or CPU usage.
Aside from the surge itself, what other negative effects could arise from experiencing an outage while multiple programs are open and running? For example, if I lost power while regedit was open, could it change or possibly cause damage the registry itself? The machine in question is currently running Win 7 SP1 64-bit.
View 6 Replies View RelatedThere was a quick power outage and the computer was forced off. I rebooted and now after the windows logo there is a gray screen that remains a very long period of time before the desktop appears. I am able to move the mouse but that is the only functionality I have.
View 4 Replies View RelatedI run windows 7 on a laptop (Asus G74SX) w an SSD and i forgot to connect it to the battery when i took a nap.Lately my battery is not in perfect state and when this happens, reconnecting the plug won't let me resume system, i have to restart windows 7 and get the message that windows improperly shut down etc etc.
View 1 Replies View RelatedI have been having a serious issue with my PC. The PC will boot up without incident, but if I try to access explorer or the OS, it will slow to a crawl and eventually freeze. I have encountered this with firefox, the start menu, and when trying to access the task manager. The problem is consistent, occuring everytime I start the machine. Usually within the first few minutes of a boot-up, Windows has frozen and I must force a hard reset.
The only thing I can think of which may be the cause is a power outage which occured in the night. When I woke up, the PC was off and the problem began as soon as I booted up. The PC was plugged into a power strip which was not tripped by the outage.
I can boot up in Safe Mode, which delays the onset of the crash, but doesn't stop it. I have tried using system restore by accessing the menu during start-up (F8) but the system restore always fails at the very end. Looking at the inside of the PC, there doesn't seem to be any visible damage (that I can detect) and at no points does anything seem to be giving off any excess heat.
When I press CTRL+ALT+DEL in an attempt to access the task manager, the screen goes black and the cursor turns to a wheel. After several minutes, the wheel will stop and a prompt will appear stating "The logon process was unable to display security and logon options when CTRL+ALT+DELETE was pressed. If the operating system does not respond, press ESC or restart the computer by using the power switch."
I had power outage reboot backgroud went back to default and so did the quick launch menu also some of my games act like i never played them before and have to re setup resolution and settings. Did some widows file get corrupt why did this happen?
View 6 Replies View RelatedYesterday, there was a short power outage which caused my computer to force shut down. When I turned it on, the screen resolution was off, so I managed to fix it by hardware (the auto button on my monitor) since software-based fixing didn't work (which has managed to solve this problem in the past, at least I think it was the same problem). Anyway, after I did this, the icons were strange; bigger than usual, not e.g. 128x128 but rather 140x128 (that isn't the exact size but they were higher than they were wide). This is quite annoying. The circular icons have become ovals and the square icons have become rectangular. By the way, the same thing has, I think, happened to the taskbar as well. It's harder to tell with things other than icons, but it's visible. So basically, everything is slightly higher than wider than it should be, not only the icons.
View 3 Replies View RelatedI am hooked up to a UPS, but when that runs out and I am away, I sometimes need to be able to remotely logon to my computer. Is there a way to get the BIOS to automatically restart the computer after the UPS runs out when the power goes out?
View 3 Replies View RelatedI literally just built this today and was able to enjoy a very fast boot up speed with wim7 64-bit installed on my ssd drive but the power cable of course found a way to get unplugged from the wall and now the it takes an extra 20-30 seconds in order t boot up (at the "windows starting" ) screen. Right after I turned it back on the computer wanted to go into system repair and then it reset the pc to the back up that I had just set,
Is there anything I can do in order to get it too boot up like it was at first?
I recently did a system restore late at night just so this problem would not happen (around 2am) with no weather and with my luck the power clips on and off. I use windows 7 home edition. When I start my computer it does not go to the login screen but shows a big bar at the bottom saying "windows loading files".I have tried several methods on the repair screen such as:
1) Trying all of the system restores which show it failed
2) Going to the command prompt and typing
diskpart
list volume (to get drive letter)
select volume D: (my drive letter)
detail volume (making sure readonly is off)
Then I typed chkdsk D: /f it went through steps 1-2 fine but at 3 it explains that it "failed to transfer logged messages to the event log with status 50" System repair fails even with the disk in the computer, and I have no clue what to do.
my computer doesn't have 'factory settings'.I'm not all that versed in computers and this is the first one I've build on my own, however, it's beginning to run very slowly and I would like to completely restore it back to it's original form, from when I first built it.I have my windows discs (but i don't have the drivers for my hardware, which I'm assuming I can find online).Is there a way to restore a home build computer? Everything I've read talks about 'factory settings'.
View 4 Replies View Relatedmy computer says windows is starting up, then windows is shutting down.
View 1 Replies View RelatedEarlier this evening I downloaded My Colors and put it on my computer. For some reason it wouldn't load up all the icons and was messing up my browser when I would go online. I did a system restore back to a previous date. Now I am in a huge mess. It will not boot up fully. I get a window with an easy access button in the lower left corner and a shut down button in the lower right corner and that is it. I don't want to do a full restore. I have a Dell Inspiron 1545 laptop. It is running Windows 7. I'm not sure what more information you need or that I can really get to you at this time.
View 4 Replies View Relatedso i dont know what happened to my hard drive but it went blank, so not it real life but i have a very very old computer. Its one of em hp media center pc's from the 2007 or the 2006. my intel thingy is intel platinum 4. my windows is windows 7 and when i launch the system repair disk it does not sense my hard drive and when i dont launch a disk in the computer and i boot it it says "please insert a boot disk or press a key to boot thingy"
View 9 Replies View RelatedI'm writing this from a different computer because I can't even get onto the internet on mine.Pretty much all programs fail to run. When I double-click on the icon, I get the usual spinning "loading" circle and then nothing happens.When I try to open straight from a saved file, I get an error message. For example, whenever I try to open a word doc, I get this error message: "There was a problem sending the command to the program."Symantec Endpoint Protection has been turned off and every time I go to the Action Center to turn it back on, nothing happens. I get the usual message that asks if I want to allow the change and when I click "allow," nothing changes.I've done several system restores, even in Safe Mode, and they have all failed. System repairs have all failed too. Obviously, virus scans are out of the question and Windows Defender (one of the programs that actually will run) keeps telling me that there is no malicious software to be found on my system.
This all started yesterday afternoon. I was running Firefox as usual and had a word document open that I was typing in. I walked away from my laptop and when I came back, there were three pop-ups on the screen from a virus that I had just managed to get rid of several days before. I closed them out and was preparing to run Malwarebytes when my computer shut itself down suddenly. There haven't been any pop-ups or anything that would indicate that this is a virus. However, I tried the same fix that I used to remove the virus the first time (copying the Malwarebyes file 'mbam.exe' to the desktop and naming it as 'mbam.COM' so that it will open) but even that does not work. I've tried the regedit fix that I've found in forums here but that didn't work either.
My computer has been stuck at "please wait while your windows files and settings are being restored System restore is restoring the registry" for almost 24 hours. I have a Toshiba with Windows 7 home premium 64bit .
View 1 Replies View RelatedSystem Restore will not create a restore point or restore to a previous date & time.The error message was: A restore point could not be created: An error was detected in the Volume Shadow Copy Server (VSS).The problem occurred while trying to contact VSS writers. Verify that the Event System Sevice and the VSS service are running & check for associated errors in the event logs (0x80042318).Volume Shadow Copy is started & running (done in system events).Event System Sevice and the VSS service are started and running. But no cigar, SR still broken.
View 9 Replies View RelatedI recently did a system restore to factory settings and now my computer is running very slow. I have done all the windows updates and checked for any updates on the drivers. I also defraged it. I noticed that the physical memory is always very high between 85 and 100. The CPU is 10-50.
View 5 Replies View RelatedI am losing my system restore points and my computer is not creating them on its own.
View 5 Replies View RelatedDoes anyone know how to schedule/automate a rollback to a system restore point at a set time each day?What i'm trying to do is:1. Disable the standard system restore behavior for creating restore points when installing apps and drivers.2. Automatically/schedule a restore point to be created every morning. (probably using Task Scheduler)3. Automatically/schedule a rollback to that morning restore point every night.This should allow users to mess up the workstation during the day, and restore a working rollback point at night when users are not using a workstation.Updates are scheduled at nighttime, so before that happens, it should rollback to a good restore point, apply updates, then create a working "new" restore point with the updates in the morning....etc.
View 4 Replies View RelatedI have an Acer Aspire timeline computer I bought 2 years ago. This computer advertised great battery life, internal cooling, and all sorts of other cool things....unfortunately, it was all a lie. But enough about that, As of like 3 days ago, I noticed my computer would respond slowly and take forever to complete a shutdown. I thought nothing of it until I decided to scan it usingSuperAntiSpyware. It came back with 40 tracking cookies, which I deleted. Upon rebooting my computer, I noticed it was still running slowly. So I decided a system restore would be niceI tried the first availible restore date. That apparently failed. Then I tried several others, with no success. I kept getting error codes telling me that the system restore failed to extract the file. It said the disk failiure might have been caused by bad sectors....I have no idea what that means. Ive tried multiple restore dates, they all come back with the same message.
I do not have Norton on my computer ( I read this was part of the problem in many other machines with the same restore error, but just to make it clear, that is not part of the problem with my computer). I can only use my computer in safe mode, because the regular boot mode is wayy too slow and laggy. Also I have plenty space on my computer so it couldnt possibly be slowing down because its getting full or something.
A few days ago, I went to turn on my computer and it just gave me a black screen after the "Starting Windows" screen. I attempted to use System Repair, which failed. It said there was an unspecified error possibly caused by a change in system configuration. I have not changed anything on my computer, for the record, between the last time it worked and now. My husband said it downloaded updates, which would explain why it was off in the first place instead of just being on stand-by. Anyway, I then tried System Restore, which also failed. I can get it to start in Safe Mode with Networking, but it seems that everything I try to run to figure out what the problem is, is saying it can't find the problem. I enabled bootlogging and found this...
Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter
Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter
Did not load driver @nettun.inf,%teredo.displayname%;Microsoft Teredo Tunneling Adapter
Did not load driver @hal.inf,%acpi_amd64.devicedesc%;ACPI x64-based PC
Did not load driver @battery.inf,%*compbatt.devicedesc%;Microsoft Composite Battery
Did not load driver @netavpna.inf,%mp-agilevpn-dispname%;WAN Miniport (IKEv2)
[code]....
i've tried to set the option for pressing the power button to 'Do Nothing' so no body can shut the computer, and yet it shuts down by pressing the button, so why is that and how can i work this out?
View 1 Replies View Relatedmy desktop computer won't boot. When I turn it on it displays the welcome splash screen and then goes black. A message will then display that says CMD failed to start and then it will shut down. It does the same thing in safe mode as well.My question is. I have already set up the HD from the desktop as an external to my laptop so I could get files off it. Is there any way to do system restore on the hard drive when it is set as an external? Because I did this last night and I think if I restore the drive it will fix it.
View 2 Replies View RelatedI turn on my computer and it will take me to the log in screen but the mouse is stuck in the middle of the screen and my keypad wont work. So I can't log in and get to my desktop. I've turned my computer off and retried several times. It was doing this yesterday too. I've tried restarting it in all the different types of safe modes, and still nothing.
View 1 Replies View Related
