Started laptop (Lenovo) opened fine, but no connectivity to internet. Desk top PC close by, has internet.Tried to RestoreLaptop did not, shut down after 30 minutes. Tried System Repair, did nothing for 45 minutes. Shut down, restarted, did not open.
Win 7 no boot to windows or safe mode Startup cannot repair or System Restore Drive has changed fron C to D, PC was showing black screen 2 options Start windows normally or Launch Start up repair 1 beepthen launches startup repair.checkingsystem, then cannot repair and send info about this problem.
my Windows 7 64-bit computer acted oddly (after it accidentally got unplugged while on, tho not sure that's what did it). now when i boot i get as far as the windows 7 logo starts to show, then i get that it can't boot.
i changed nothing that i know of. repair says it can't. restore, which only lists points from 3 days ago, doesn't work. i did a memory test. it was fine. am i doomed to do a clean re-install of Windows 7?
btw, if i get that Windows 7 logo, and also a stage where it says it is loading files, that means it is reading from my hard drive, right?
my Windows 7 64-bit computer acted oddly (after it accidentally got unplugged while on, tho not sure that's what did it). now when i boot i get as far as the windows 7 logo starts to show, then i get that it can't boot. i changed nothing that i know of.
repair from my bootable Windows 7 disk says it can't. restore, which only lists points from 3 days ago, doesn't work. i did a memory test. it was fine.
am i doomed to do a clean re-install of Windows 7?
btw, if i get that Windows 7 logo, and also a stage where it says it is loading files, that means it is reading from my hard drive, right?
Problem: This morning I had a brief 1 second power outage while I was using my computer which forced it to shutdown. It just stood there shutting down for about 15 minutes when i decided to click force shutdown. After restarting, computer ran checkdisk and startuip repair because windows was not loading.
Issues; I ran chkdsk a couple times, lots of bad sectors./index files repairing recovering, but it ends up hanging at stage 4 at a certain spot. I left it running at that spot for over 5 hours and just stood there(I went to sleep and woke up at same spot). I booted with windows 7 cd and tried startup repair, the first 3 times it said it couldnt repair. It only showed 2 restore points available and both gave error messages saying they couldnt load. I ran a checkdsk /r again and was fixing a lot of stuff and hung at same spot again. Tried another startup repair, this time it said it worked but still the same problem, windows isnt loading. However, I am able to get to the login screen now after waiting about 10 minutes at the windows logo however my kieyboard/mouse functionaility seems to be gone so i cant even type my password to login at that point. I ran a diagnostic in the boot menu, when checking the harddrive it gave me an error. Ive tried booting to every option available, safe mode, safe mode with networking, safe mode with command prompt etc, nothing works. It brings me to logon screen after a long time but keyboard./mouse dont work at that point. Now, like i said i dont want to reformat my computer and lose all my files. My keyboard/mouse work with the windows 7 bootup cd doing those menus but not when it gets to logon screen booting the normal way. I was thinking of buying an external drive and installing windows on there and booting from there but im not sure if my computer would recognize it since it wont recognize my keyboard and mouse at login screen.
I think I must have lost Windows Installer using Revo uUninstaller and messed up the registry somehow. I'm a bit afraid to use the Win 7 repair disk 32 bit I created; I might mess things up further. I've tried to download a 32 bit installer update to no avail; it says it's not compatible with my version of Windows (Professional, SP1). Anyhow, does the Win 7 repair disk have a fix for the lost Win 7 installer? If so, I might give it a try if you can provide some guidance in doing so. I have everything backed up in Carbonite, Seagate external drive, Acronis True Image, memory sticks, etc.
I've had prolonged problems with my computer; blue screen crashes around 5-10 times a day, everyday for past 2 years. Anyway my problem today is that finally it will not start up. I get the start repair (recommend) or start windows normally. The latter of the two just fails and restart the computer. When clicking repair it say it cannot repair automatically, I have also gone into advanced boot settings and tried safe mode which also failed and restarted the computer the same goes with trying last good configuration which also does the same. I have also tried repair disc and back up disc I have but I don't if it some I'm doing wrong but they are not loading.
I was being an idiot and messed with Msconfig memory. Restarted and gave me bsod. After that I ran Startup repair system restore failed.I checked the memory box I think it was 0, not sure. if you need additional information let me know.
I recently downloaded a damaged file, which caused my computer (not this one) to be unable to start up normally. The computer now boots up in Startup repair, which is unable to repair my computer "automatically" and when I then click "View advanced options for system recovery and support" and go to the "System restore" tab and choose a Date and time for the restoration, it tells me that "There is not enough free space to restore the disk". I seem to have no options to try and sort out the missing space on the harddisk, which should be unnecessary because I am pretty sure there is still alot of disk space on the C.
i got a hp pavillion running windows 7 i was installing the windows update and pressed restart now, after this the force restart thing came up but i pressed cancel and it didnt like this, after 2 minutes of program errors it restarted and went straight into startup repair. running it on normal mode doesnt work and safe mode is not available. when it runs startip repair it wont fix anything and tells me to restore, i can get to the windows restore part and have restore points but they do not work and an error is shown, x8000xffff if i remember correctly.
I have never had the need t use this disk till now but as I am getting problems starting up I tried System Restore and it didn't work (I have tried 2 restore points).Can I use the repair disk that I created on my HP desktop to mend the system or to restore it to an earlier time ? When I open the repair disk on the computer it just shows a couple of folders (boot ,sources as well as a file called bootmgr but I can't see a hrep file to let me know what I can do...
Last night I closed my laptop without shutting it down. I woke up this morning and turned it on and it went to the system repair screen and ran through that. It says there are problems but they are not automatically repairable. I then tried to do the system restore to an earlier point in time and had one option for a couple days ago. I ran through that but it says there is an error and when I expand to see the error one of the things listed is no OS installed. I have windows 7 64bit. Why it would say I don't have an OS installed but it is running through the system start up repair as well as listing a date that I could restore it back to. I have not tried installing the hard drive into a new computer yet.
I have a few friends that would like me to fix some virus/malware issues. Most are Win 7 users(a few running XP), but don't have any of their installation media or driver disks or anything. I've had a few personal instances where I used Norton or a similar program to scan for viruses before, and when it did so it removed some of the boot files, or some other system critical file. I don't want that to happen here, cause I don't want to give them back useless machines.
Can I just create a "Repair Disk(DVD)" in Windows? Will that take care of an issue like the one I described above? Should I use an external to create images of each, one at a time, run the scans and then use the image if anything goes wrong? And if something does go wrong, how would I restore from the image? I've never done that before, and I'm eager to learn.
My Sony vaio just turned off last week and wont boot up. It turns on an flashes Sony vaio but that's all. I made a recovery disk and I can get into bios so I tried booting from internal disk and tried startup repair got nothing, tried system restore for every restore point and none will finish. Took each piece of ram out an tried starting it up to see if bad ram was the problem and it starts the same way. I also tried the restore from previous image but I have no image. So I don't know what else to try. Windows 7
A few days ago, I went to turn on my computer and it just gave me a black screen after the "Starting Windows" screen. I attempted to use System Repair, which failed. It said there was an unspecified error possibly caused by a change in system configuration. I have not changed anything on my computer, for the record, between the last time it worked and now. My husband said it downloaded updates, which would explain why it was off in the first place instead of just being on stand-by. Anyway, I then tried System Restore, which also failed. I can get it to start in Safe Mode with Networking, but it seems that everything I try to run to figure out what the problem is, is saying it can't find the problem. I enabled bootlogging and found this...
Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter Did not load driver @nettun.inf,%isatap.displayname%;Microsoft ISATAP Adapter Did not load driver @nettun.inf,%teredo.displayname%;Microsoft Teredo Tunneling Adapter Did not load driver @hal.inf,%acpi_amd64.devicedesc%;ACPI x64-based PC Did not load driver @battery.inf,%*compbatt.devicedesc%;Microsoft Composite Battery Did not load driver @netavpna.inf,%mp-agilevpn-dispname%;WAN Miniport (IKEv2)
I have recently installed windows ultimate x64 on my computer.i have an asus p6t deluxe v2 mobo, i7-960 cpu and a wd velociraptor hdd. The install went ok, I even managed to restart my computer a few times after but after windows updates installed it won't boot. I tried to boot into safe mode, restore from the installer, and repair, none worked. After startup repair it says: "a patch is preventing the system from starting" and I get a 0x1f error code.(Preventing windows from downloading any updates didn't work either)
XPS L401X Base Genuine Windows(R) 7 Home Premium 64bit (English) Intel(R) Core(TM) i7-740QM Processor 6GB 1333MHz DDR3 SDRAM (1 x 2GB + 1 x 4GB) 640GB 7200RPM Hard Drive
Lately whenever i try to start my computer it pass the Dell Bios and then directly goes to the screen which states Repair your system or Start windows normally When i chose repair system , it start downloading windows files and then launch the windows , but hung up at the sky blue login window with only movable cusor . When i choose to start windows normally it gives me BSOD momentarly ( hard to see the message) and then restarts again . i tried with the advanced boot up options like repair my computer , all safe modes , restore to last good configuration but it does the same and hangs at windows loging sky blue window .I Tried to run the Dell PSA+ Diagnostic and it returns with 2000-0146 error . As per the Dell online solutions for this type of error ,I tried to reinstall the Hard disk but the problem still exist.
I have 3 corrupt installations of the same OS (Windows 7 U. 64 bit) in the same hard drive. I can't install any OS(es), and my original (working installation) no longer works. These corrupt installations are corrupt because windows installed incorrectly twice they left old windows instead of creating a windows.old file.When I try to start up any of these three installations, I get the same error: "The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer, and then restart the installation."This also happens upon completion of reinstalling windows.I have tried to wipe the drive:most programs I see need windows to operate...I've tried a few programs that can be booted, DBAN boots, but I get the same error every time: That DBAN has encountered a non-fatal error and that the error is usually caused by damaged disks.
Living is south FL can be a bitch when the rains come as there often is a ton of accompanying lightening that plays havoc with the electrical system, even though I have surge protectors inside and outside the house. We just had some very heavy rains with lightening and my computer shut down several times, but I could restart it each time...except for the last time when Windows wouldn't startup. At that point, Start Up Repair came into play. Although I routinely backup on an external drive, of course I never did it this month-DUH!Results from SUR were error free (error code=0x0) on all the parameters tested, however there were the following error codes reported:"Unspecified change to the system configuration might have caused the problem." Failed: 0x1fRepair Action: System FilesFailed: x490There were more options to select for a recovery task, but I didn't try them as they didn't seem to be as salient as the two above.
I installed a new MOBO last night (17/02/2012) and booted up and my Windows 7 could not boot. It went into repair mode and could not repair.
So I installed a new Windows 7 and now see the Windows.old folder. I would like to recover the huge amount of settings and personalisation from the old Windows system.
I have not communicated with anyone who has REALLY had a Windows recovery ever work. If anyone knows, this is the perfect time for me to be shown the light.
The other day I was trying to figure out what coral paintshop pro meant by security key, so I googled it. Something popped up and asked me if I wanted to download, and I wanted to say no, but my laptop's mouse is too sensitive at times, so I accidentally clicked yes. My computer automatically shut down right after that. Every time I turn it on now, it goes straight into System Repair and it doesn't work, it says it cannot repair. I've tried System Restore, but since that doesn't get rid of the documents that have been downloaded, it isn't helping either. My computer won't even let me enter any form of Safe Mode, it just goes straight back to System Repair.
System Restore will not create a restore point or restore to a previous date & time.The error message was: A restore point could not be created: An error was detected in the Volume Shadow Copy Server (VSS).The problem occurred while trying to contact VSS writers. Verify that the Event System Sevice and the VSS service are running & check for associated errors in the event logs (0x80042318).Volume Shadow Copy is started & running (done in system events).Event System Sevice and the VSS service are started and running. But no cigar, SR still broken.
have got windows 7 ultimate version of operating system on my system, . but i also want to install windows xp in it for some reasons related to my education. can i install an other operating system along with the existing one, such that at every start up i could select the required os to be functioned
How to move my systems on partitions ? i have 2 system partitions. vista 50gb, 2 years evolved seven RC1, working stable enough both on the same hd. how to i toggle them? i guess boot-manager than will not exist anymore.
I was just wondering about the 32bit RAM range, if im not mistkaen a 32bit system can recognize up to 4GB of ram right?
If so how much does Windows 7 have reserved? because i have 4gb ram installed but windows only reveals 2.99GB RAM useable in the control panel. Anyone can clear this up?
I have 2 internal HDDs. My primary is Ubuntu and the second is Windows 7. The system time is correct is Ubuntu but 4hours ahead in Windows. I reset it, but after I boot into Ubuntu my Windows will be 4 hours ahead again the next time I log into it.
I've spent the last couple of days trying desperately to resolve this issue. I have looked everywhere but cannot find an answer... PROBLEM: I have thousands of PDFs in hundreds of folders. When I go to a particular folder, I use the slider to change the Explorer views from "Content" to "Extra Large Icons" but cannot get a thumbnail preview of the PDFs - all I see is an Acrobat Icon preview.I know that this is an issue on the X64-bit verson of Windows 7, but I'm running 32-bit Windows 7 (Ultimate)! ATTEMPTS: I've tried several ways to resolve this but nothing worked so far. Specifically, I: 1. Made sure that the File Type Associations are correct.2.Unchecked Folder options>View>"Always show icons, never thumbnails".3. Made sure that Folder options>View> "Display file icon on thumbnails" is checked.4.Made sure that Performance>Settings>"Show thumbnails instead of icons" is checked.5. Tried the simple method suggessted at other forums: going into Adobe and opening the directory to preview the files as thumbnails from there and then refreshing the folder in Windows Explorer to display a thumbnail preview of the PDF file - Didn't work either!6. Ran "Repair Acrobat Installation".7. Uninstalled and Reinstalled Acrobat 9 (including associated registry files).8. Installed the latest version of Reader.9. Tried installing other software (PDF-XChange and Foxit) but these don't create PDF thumbnails in Windows Explorer either.
I looked in System Configuration on my W7 Ultimate.....There are 80 systems running. Which ones can I shut off to make my pc run faster with W7 and not mess it up. This is just after I rebooted I didn't have anything open yet. [code]