Last thing I did on my laptop was download baseball team logos a couple days previous to problems.. Use mobile hotspot for internet and this is not working in SafeMode. These are the lap top specs, and can provide more if needed: [CODE]
View 9 Replies
I have been getting BSOD errors whenever booting into regular mode. Safe mode is fine (I have tweaked the registry so I have sound in safe mode) My system specs are in my profile, but used Winaudit for full specs. The winaudit report in formatted text is too big for an attachment. I have 2 attachments to this post, including zipped up minidumps. Could my registry tweak for sound have something to do with this? Perfmon /report was run, but it says:
An error occured while attempting to generate the report. The system cannot find the path specified.
After attempting to start my Laptop in Safe Mode, it loaded drivers normally only to crash a few seconds later. A prompt message appears but is impossible to read because Windows immediately reboots upon showing the prompt.
View 1 Replies View RelatedSo I am having trouble with my computer since last night it started to give me the blue screen of death every 10-15 minutes with all kinds of different reasons. I cleaned my pc, searched for viruses as much as I could, and I have restored to a different point in time twice. I have tried the windows memory diagnostic twice. No issues. I have tried the files check before start up, no issues were detected.Pfn_list_curruptan attempt was made to write read only memorysomething on the lines of service_system_exeption? Not sure about the last word to be honest I caught it while my computer restarted on its own. Memory_ managment Bad_pool_errorI am not sure what to do I have done all I can by myself. I will be doing a complete restore to manufacture settings after I get something to back up my files. In the meantime maybe I can figure out if it is a hardware issue or if there is something else currupt.
View 2 Replies View Relatedmy pc semi froze, wouldn't let me access control manager and browsers forze but other applications were working. So i decided to restart my pc and upon restarting it froze on the bootup screen (windows logo). I tryed accessing safe mode but got stuck on " windowssystem32DRIVERSCLASSPNP.SYS ". Once it crashes on the boot up and I press the reset button my main drive is no longer detected by my bios but when i fully shut down the pc and start it up again it gets detected no problem. I have browsed around and I have seen a lot of people stating it was bitdefender, but as I cannot gain access to my safe mode to restore or delete it I have no idea if it really is that. I would like to hear your suggestions on the problem, I could take my ssd out and put it in an external drive and plug it into my laptop to try and delete bitdefender but as its mounted to the floor of an antec 902 and its pretty jam packed in there id need to removed my gfx cards hard drive trays, and power supply just to get to it and that is something I really dont have the time for.
View 4 Replies View RelatedI am having a serious problem whenever I try and load windows it freezes at the main page. I can, however, access internet easily in safe mode.
View 2 Replies View RelatedMy computer has been stable for years, however recently I have been getting BSOD when doing any task. Windows will sometimes load to the desktop and I am able to watch video, run windows score, check email, etc before it will BSOD. Other times, it will BSOD before getting to the windows login screen.When I use safe mode, it logs in and stays there - no BSOD.I have tried removing all extra hardware in the machine, however this has had no affect. I have also tried one stick of RAM, then another, both BSOD.
View 3 Replies View RelatedAcer Aspire ZR7 model stuck on "Setup is starting services", never progresses.I can't locate o/s discs et.al.It will not open in safe mode using F8.I've also attempted Lft ALT + F10, no good And, F12 at Windows screen. No good.
View 7 Replies View RelatedI was on my computer today (Win 7) and programs just started shutting down and the computer reset. The computer starts back up (Asus) and when it gets to the point where windows starts, the screen goes black and there is a blinking cursor line. Not buttons work at that point.In my manual for the Asus and it says to select a boot device, press f8 when he Asus logo appears, to access Windows in Safe Mode press f8 after post. I start pressing f8 at all different times, but all I can get is the boot device menu or a blank screen.I put in the WIN 7 disc and told it to do a startup repair - it says nothing is wrong. I try a system recover from a few days ago, and it has an error and can't do anything.I was running Norton Virus and it didn't pick up anything before the crash, I also have Norton Ghost and I think I have a backup from a few days ago. But I can't seem to access anything
View 1 Replies View Relatedi have toshiba satellite A205 win 7 its been freezing a lot lately i dont know why so i tried to install Windows 7 OS again (its not genuine) i usually do this successfully if i get virus but i dont think its virus this time but during the installation it got stuck it passes the copying windows file up to completing installation but it says it needs to be restarted and i did this several times it either hangs up or tells me cannot be installed restart.whenever i start all over again a black screen comes up with listing windows 7 several times asking me to select 1.i select the latest but same thing happens allover cannot access safe mode either i tried to install win 7 ultimate geniune but same thing happens.i also tried the repairing option its not working keeps telling me to restart..i believe its the hdd thats corrupted.i need to get my files.
View 4 Replies View RelatedI was on my computer today (Win 7) and programs just started shutting down and the computer reset. The computer starts back up (Asus) and when it gets to the point where windows starts, the screen goes black and there is a blinking cursor line. Not buttons work at that point. In my manual for the Asus and it says to select a boot device, press f8 when he Asus logo appears, to access Windows in Salf Mode press f8 after post. I start pressing f8 at all different times, but all I can get is the boot device menu or a blank screen. I put in the WIN 7 disc and told it to do a startup repair - it says nothing is wring. I try a system recover from a few days ago, and it has an error and can't do anything. I was running Norton Virus and it didn't pick up anything before the crash, I also have Norton Ghost and I think I have a backup from a few days ago. But I can't seem to access anything.
View 1 Replies View RelatedI recently just put together my very first Gaming PC Build and everything looked fine. The Gpu was running, motherboard fine, everything except the Motherboard with the CPU. I have heard from a lot of people that AMD Phenom II x4 965G + ASUS Motherboard 760G just glitches out even though I can run the system up and play all of these high CPU dependable games like L4D PERFECTLY with out any problems what so ever. I reboot the computer I am sent to the black screen with "PRESS F8" to open Boot Menu or Bios" I believe. Press DEL for what ever and TAB for EZ FLASH 2, I already updated the correct bios update from ASUS website of my model Motherboard but this will not go away and I have no way to access the "F8" for Safe Mode and all the other options, I am using Windows 7 Home Premium.
View 4 Replies View RelatedI forgot to plug in my computer and the battery died. When I tried turning it back on, it takes me directly to:
"Startup Repair - Your computer was unable to start. Startup Repair is checking your system for problems. If problems are found, start up repair will fix them automatically. Your computer might restart several times during this process. No changes will be made to your personal files or information. This might take several minutes."
Followed by a loading bar that says searching for problems. After leaving this on for a while it gives the system restore option, however this just takes me back to the previous screen. I cannot cancel the Start up repair and I can't access safemode. After searching for over an hour the only solution I've found so far is reinstall the OS, however my computer did not come with the OS disc and I have school related files on the computer that I can't lose.
I am using a Toshiba Satellite A505-S6981 T6600 That's 9 months old with windows 7, Specs (To my limited knowledge) say:
C2D 56600, 4GB DDR3
16", 400 GB HD, DVDRW
Windows 7 P 64 Bit, 80211bgn
When I start my computer everything seems to be working fine but after login it says Please Wait then freezes at Welcome screen and the cursor can be moved around the screen and shows the loading icon and the screen also flashes black every few seconds. I've restarted and attempted to access Safe Mode however it also freezes at Welcome screen. I went into the repair system screen and tried a system restore but it says there are no restore points available and I know I haven't deleted my restore points. I've tried disconnecting any of the hardware I've had installed but that hasn't helped either. There also isn't any faulty hardware. When it was last working it said there was a Windows update so I installed the update but when I tried to turn on the computer the next time thats when the problem started and I don't remember what the update was for. I upgraded from Windows Vista Home Basic 32-bit to Windows 7 Home Premium 32-bit about 2 months ago and up until now I've had no problems with it. What can I do?
Here are the system specs:
Dell Inspiron 530s
Intel Celeron 2.00 Ghz
3.00 GB DDR2 RAM (I added 2.00 gigs myself came with 1.00 gig from factory)
Windows 7 32-bit upgrade from Windows Vista Home Basic 32-bit
250 Gb Hard Drive
Earlier today I wanted to get into Safe Mode in order to cleanup up leftover files from an uninstall of Catalyst.I have a hard time getting into safe mode via my BIOS so I generally use msconfig. I always set it to run straight into Safe Mode (which is what I did today). When I restarted I got the 01E BSOD. I'm assuming it is another driver or that my system files are corrupted.I checked my hardware and individually ruled that out.Now I am in a situation where I cannot boot into the regular OS to try and figure out what is really going on (gather the dump files etc..). I have been trying to access msconfig via the command line from my DVD but can't figure out how to get the right permissions and actually run it to turn off the safe mode boot option. I use a RAID 0 startup so I have to load the RAID drivers when I pop in the DVD. Then I have to switch drives from the command prompt from "X" to whatever the RAID drive shows up as.
View 4 Replies View RelatedEarlier this week my HP desktop forced shutdown while browsing the Internet using IE9. Upon reboot the HP screen loaded, afterwards a black screen with a flashing cursor appeared. I had used CTRL+ALT+DEL function in which my computer rebooted.Showed the HP screen and immediately showed the black screen with a flashing cursor. Again no mouse cursor was available. I performed a diagnostics check in which the CPU, HDD, etc. checked out, restored BIOS to factory settings, even placing the HDD as priority 1. I inserted the Windows recovery disk and attempted a start up repair, and a restore point with no favorable results. Through the recovery disks command prompt I accessed all my music and documents, so I assume the hard drive is still functioning. I'm thinking as a last resort of performing a repartitioning of my hard drive and performing a clean install of Windows 7.
View 2 Replies View Relatedmy computer was running fine then yesterday i suddenly got shut down and anytime i turned it back on i would get a BSOD after a few seconds unless i went to safe mode its a page_fault_in_nonpaged_area 0x00000050.the only thing different is i downloaded borderlands from steam, played for about 8 hours, then got the packs running, then 10 mins later it shut itself down on its own currently system restore only had 2 options for 8am when i downloaded borderlands, 1 said critical system update adn the other was direct x 9 im not good with computer hardware so if u need any more info tell me, but heres some system stuff System Info Processor: Intel(R) Core(TM) i7 CPU 960 @ 3.20GHz
[code]...
getting BSOD after boot and desktop comes up. i can get in safe mode without BSOD coming up. Attached SF Diagnost. from my Dell Laptop.
View 3 Replies View Relatedi recently tried removing some malaware from a laptop that kept rederecting my webpages. I used Hitman Pro and after scanning with it it asked me to reboot for the changes to take affect. One it rebooted igot the BSOD message. i Cant boot in safe mode so im lost on what option i have left. The main point is that i dont want to preform a clean install, and delete my documents.
View 3 Replies View RelatedMy set up is or was dual boot Windows 7 rc712 x64 and vista x64 on 2 partitions on the same drive. Suddenly bsod and looped rebooting with windows 7 and I can't even load windows 7 in safe mode. This ocurred after a video crashed in windows 7. I could not load safe mode but I could load vista x64 reguarly(it was a fresh OS I never used). I did a windows 7 upgrade install over the vista when I meant to reinstall on the windows 7.
I had tried to boot from windows 7 disk and couldn't repair the old windows 7 installation. How do I get back to my original windows 7?
Some other babkground info. Prior to all this but maybe unrelated were dreaded nvlddmkm.sys errors even after fresh installs of windows. This error was under my old 32 bit vista right after I changed video cards and occured after windows loads or windows media player opens. My solution was reinstall windows thus I upgraded to windows 7.
My orginal windows 7 custom install(not upgrade) still had some errors though not as many errors and I could boot into safe mode, shut down, then everything was back to normal until the next error. XFX(my video card manufacturer thinks it is a software driver issue and not hardware).
my laptop looks like it has a massive problem. i have been on various forums for advice but unable to solve - this is the problem
* it turns on & I CAN get into advanced menus
* it will not repair itself no matter what
* it will not go into any other modes , safe Etc....therefore I cannot restore to factory settings etc....
* ive Tried all tricks such as F8, Alt & F11 etc..... to get into advanced menu settings - all lead to the black screen
* everything i click on enter leads to a black screen - only a white curser appears.
its as if there is no way of accessing the computer disc/ hard drive in anyway from boot up. there is clearly a hardware problem but i cannot access anything internal beyond ordinary & advanced menus i just keep being led to the black screen & no activity. the menus work & that is all.
i run Windows 7 on a Dell inspiron 1564
So last night I updated my computer (which I don't often do). Then today I go to play a game and I bsod. Try again, same thing. I boot in safe mode. Bsod again. I boot in safe mode once again and revert to a restore point from three days ago. I go to play the game again, bsod. There's only the most recent bsod saved from all of it, which I've uploaded here: [URL]. I didn't write down the information to "find solutions" for, unfortunately, suffice to say that the error given was just BlueScreen.
The updates I installed were:
KB2588516
KB2617657
KB2620704
KB2641690
KB890830
As well as a small handful of office 2010 updates.
I have been having nonfrequent bsod errors for quite a while, and since playing a game of Starcraft 2 today (~3 hours ago) my computer started to constantly bsod. I can not log into windows for more than a minute or two (if that) before it BSOD's again. I am currently posting with my laptop, and the desktop that is BSOD'ing is dualbooting linux (ubuntu) which has no BSOD issues whatsoever. I also ran the memtest that comes with installing ubuntu and no issues were found. Attached are my minidumps.
View 5 Replies View Related[code] I couldn't do a health report due to being stuck with safe mode with networking. The BSOD started about two months ago while the gf was using it and didn't happen for me till yesterday. As of now I can get it to start normally but It crashes any time I open anything. I tried swapping ram and no change. I honestly don't know a whole lot about windows 7.
View 9 Replies View RelatedAcer AO522 64 GB SSD by Transcend
0x000000F4 (0x0000000000000003 , 0xFFFFFA8003418B30 , 0xFFFFFA8003418E10 , 0xFFFFF80001D9B8B0 ) BSOD ( disk drive related I guess ? )
Like in the topic - BSOD shows up at startup, even in safe mode.
I don't have any minidumps - just the memory dump.
I'm frankly not that familiar with Windows 7. Also, this isn't a computer that I used, so I'm not familiar with what exactly was happening, if anything, before the situation it's in now.My friend has the following system:Gateway NV7915uIntel Core i3 330M 2.13Ghz500 GB SATA HDD4 GB DDR3 SDRAMWindows 7 Home Premium 64 BitOn Start Windows Normally, it just freezes on "Starting Windows" I have left it like this for days with no progress.On Launch Startup Repair, "Windows is loading files..." OK Then when "Starting Windows" appears, BSOD:DRIVE_IRQL_NOT_LESS_OR_EQUALSTOP: 0x000000D1On Safe Mode, BSOD at classpnp.sys:PAGE_FAULT_IN_NONPAGED_AREASTOP: 0x00000050On Debug Kernel, freezes on "Starting Windows"On Windows Home Premium 64-Bit Recovery Disc (I downloaded this, I did not make it from this system, the owner never did this), Windows Setup [EMS Enabled].... "Windows is loading files..." OK, Progress bar moves a bit and then:STOP: c00021a {Fatal System Error}The initial session process or system process terminated unexpectedly with a status of 0x00000000The system has been shut down.
If I use a Retail Windows 7 Disc, "Windows is loading files" OK, then "Starting Windows" the logo forms, and boom:STOP: 0x0000008EI took the HDD out of this system and popped it in my tower. I ran a virus scan (as expected, nothing found), ran an Advanced System Care 5 scan/cleanup. Then I ran a Check Disk (Checked - Automatically fix file system errors and Checked Scan for and attempt recovery of bad sectors), finished fine. no issues.All files are accessible and everything seems fine on the HDD when it's a slave in my tower.So at this point, since I cannot boot into any form of Windows or repair or command prompt that I am aware of, what can I do?
i been getting bsod alot in the past week a few time i got a few with ROQE LESS OR EQUAL something like that but i think i solve that already. now i getting the 0x000000f4 it just appear yesterday when i was watching a movie online snice then no matter if i start it on normal or any safe mode it appear after like 5 second after the restart so i cant get the dump files. the only thing i overclock is the cpu fan thats it.
View 9 Replies View RelatedI have a Compaq persario CQ62 laptop i was on facebook about a week ago and signed out and my computer froze i powered it down and when i turned it on i thought it was going to start and then it went to a blue screen. I am doing this from another computer because i cant get that one to boot from anything disk or drive. I can not access safe mode or repair mode If i try to load safe mode it does not even show me the file its loading.
View 9 Replies View RelatedI can only run Windows 7 Home Premium (different computer than the one I'm posting from) in safe mode. When I try to use the Diagnostic Tool, it says that it is saving the files but then it doesn't finish up with giving me the folder on my desktop. How I can get the files to show so that I can attach them to this thread?
View 3 Replies View RelatedThe CPU, heatsink, motherboard and RAM came premade by 3XS from SCAN. I have made sure it's all seated properly etc.
Intel i7 2600 @ 3.4gb
8gb RAM Corsair Vengeance
Win 7 64 fresh install
Radeon HD 7850 Graphics Card.
Asus z77 motherboard.
However after about a week of usage with no errors all of a sudden I have started getting the odd BSOD, and today I have had about 20, even in safe mode.
Dell Inspiron laptop, working fine, shut itself down last night mid work and now will kind of start up but only go so far. am left with Black screen with a blinking cursor in the top left hand corner. Managed to get f8 to work after a while. It runs the pre-boot system assessment build 4116 - everything gets a "pass" except The hard drive which gets a "running". All memory tests "pass" also. After this it will go no further, no more screens. Running windows 7....F2 and F12 will not work either so cannot start in safe!
View 2 Replies View Related
