Stop Screen When Installing
May 2, 2008
I received the following Stop screen error code after installing SP 3 to my XP Home Edition OS.
Stop:0X0000007E (0XC0000005, 0XF781C756, 0XF79F7430, 0XF79F712C)
I had to reboot in safe mode and uninstall SP3 to get back to normal, which is Service Pack 2. The PC is an HP Compaq SR1520NX with 1GB Ram and 160GB HD with plenty of room. The only hardware I had a bit of trouble with was an Nvidia AGP card which they helped me with updating the driver several months ago. I don't seem to have any problems otherwise with it. Also, I installed a Pinacle USB TV
Tuner. I've had some problems getting it to recognize the tuner occasionally. Sometimes when I unplug it and re-plug it, it works.
How can I tell (from the error code) what is causing the stop screen?
View 6 Replies
ADVERTISEMENT
Jul 18, 2008
I put in My CD and it goes through the first blue screen (the one where is asks if you want to press f2 to do install drivers via A drive etc) and when it gets to "Setup is Starting up windows" (this is before all the HD formating and partitioning) I get the blue screen. it does not have much info on it all it says is:Stop: 0x0000007B (0XF78D2524, 0XC0000034, 0X00000000, 0X00000000)
View 5 Replies
View Related
Jan 7, 2009
I have just installed a Samsung CLX-2160 on my Dell Dimension 5150 PC,which runs Windows XP Media Centre.As soon as the PC started reading the installation CD, it crashed with the following (taken from event viewer):The computer has rebooted from a bugcheck.The bugcheck was: 0x0000007e (0xc0000005, 0x804f106f, 0xba4fbaac, 0xba4fb7a8). A dump was saved in: C:WINDOWSMEMORY.DMP.
I rebooted with F8 and chose last working config.After a little enlightened guesswork and advice I removed my old Dell 725 printer driver(which had started giving an error message on startup). Now I could load the Samsung driver etc and the new printer works.However, XP still crashes whenever I reboot normally I can still bring up a working system with F8 as above (but I have to reload my PCI card drivers again - 2 port serial and sound card - for some reason)
View 6 Replies
View Related
Feb 5, 2006
Installing windows on a pc built for my friend and it comes up with a stop code.
stop d1. driver_irql_not_less_or_equal then it states
acpi.sys
address fc40d3b4 base at fc3fb000
which i think refers to a stop a1 as well.
ive tried using 2 different type of memory on the m-board and still get the same error.
there are no other hardware besides a cdrom and hdisk, mosue and keyboard. i did have an old logitech mouse but swapped that as i read that can cause problems too.
i dont know how to go about fixing this as their is a hotfix for acpi problems but thatr equires u to actually have windows on teh pc in teh first place i.e safe mode.
i can get into bios and it performs POST no problems. the only other thing is it boots fromcdrom but it says no emulation.
View 6 Replies
View Related
Jul 11, 2005
Now when you visit some sites they will install some program onto your computer.
View 3 Replies
View Related
Jul 26, 2005
Every time I try to install Windows XP x64 on my newly assembled computer I get 0x000000A stop scripts (mostly 0x0000003b)
The farthest ive gotten in the Windows installation was 17 minutes left for completion.
can this be something to do with BIOS? (BIOS is updated)
Computer hardware includes:
-ASUS A8V-E Deluxe motherboard
-AMD Athlon 64 3800+ Processor
-Sapphire ATI Radeon x800 pro Video Card
-Corsair Dual Channel 1gb DDR 400 PC 3200 Memory
-Seagate Barracuda 7200.8 ST3250823AS 250GB 7200 RPM 8MB Cache Serial ATA150 Hard Drive
View 1 Replies
View Related
Oct 3, 2007
Over the last two weeks, I've reinstalled Windows five times. I'm literally at my wits end. Here's my problem...
Whenever I try to install almost anything, I get Stop error 0xF4, which is the termination of a system-critical process or thread. Sometimes it happens for no reason, but for the most part, it's usually just when I'm installing something. Unfortunately, I don't have all the parameters of the stop error, but according to the Overclockers Forum, my first parameter (0x03) denotes that it is a process that is being terminated.
There are sometimes when the sfc /scannow command can temporarily fix the problem (that is, to run it before installing an app, then install the application once it is finished) but that's not always the case.
It should also be noted that there are some instances when I get a 0x7A error, but this is seldom. I merely included it in the event that it may prove to be helpful.
I'm running Windows XP Home, with an ASUS A8N-VM-UAYGZ motherboard. I'm sure you guys need more specs than that, and if so, please tell me. Also, I intended to include the Stop error message in it's entirety, but I neglected to write it down (odd, since I've seen it 40+ times). So I will write a follow-up with the Stop error and ...
View 5 Replies
View Related
Mar 15, 2006
The windows installer on my computer keeps popping up every now and then wanting to install a program I had downloaded on the net but do not want anymore. I have deleted the downloaded program file but windows installer still keeps popping up wanting to install the program.
How can I stop windows installer from popping up?
View 7 Replies
View Related
Oct 17, 2009
Recently I bought a very cheap Acer Aspire M1640-E1150 which came with an MSI motherboard, an Intel Pentium Dual Core E2200, 2 GB of DDR2 RAM, and a 320 GB HDD from Hitachi. The system came with Vista initially installed on it, and needless to say, it was very slow! I decided to do the right thing and go to XP, so I found all the drivers required and I proceeded to install Pro from a disc that I have from a previous computer. As soon as the screen booted up and the system was being checked by the program, the system gave me an error message, before I even got to partition anything, it was initial. I tried to restart, took one of my RAM sticks out, but nothing was working. I even tried to format the HDD through an external drive, but nothing was working.
The error message is "Stop: 0X0000007B" and something about a virus or a software or a hardware being the problem. The system was running smoothly on Vista, and I even formatted the C drive, and I am sure that there were no viruses.
View 6 Replies
View Related
Aug 24, 2005
I have an ailian computer with XP Home on it. After installing sp2 my usb ports stoped working. In device manager the usb root hubs and ports say that they are working but the mouse and game controler do not function. I do not get power to my mouse either.
View 2 Replies
View Related
Mar 8, 2008
I put everything together, went into bios, changed the time. Made sure everything else was alright, (boot order basically) then put in my XP disc (that ive used for computers before) and restarted. It recognized it, went to the windows blue screen where it tried to load everything. Loaded everything (at the bottom in the gray bar) then the last thing it says is "Starting Windows Setup" (or something close to that) the screen flickers and up comes a blue screen saying "A problem has been detected and windows has been shut down to prevent damage to your computer. If is the fi."
Then Technical Information:
*** STOP: 0x0000007e (0xC0000005, 0xF78E0BF, 0xF78DA208, 0xF78D9F08)
*** pci.sys - Address F748E0BF base at F7487000 DateStamp 3b7d855c
At the moment i am completely lost, my only thought was to take out the video card and see if that helped (since it said something about video drivers) but everything is brand new, and plugged in correctly (i believe) so i dont understand what is going on!?
View 13 Replies
View Related
Mar 8, 2008
Hi.I just bought an Asus P5N-D ATX SLI-ready mobo. Have 512 mb of memory to start with so I figured I would set everything up and make adjustments as I received my new parts. Started with a 250 gig Western Digital SATA 1.5 harddrive, a 600 watt Ultra PSU, 512mb of DDR2 PC6400 800fsb single channel, a P4 Dual Core 3.0 processor, and a Windows XP Home Edition 32bit disk. This isnt even close to the setup I plan to use but I thought it would be nice to tweek this processor to see what it would do before I got my new Wolfdale E8400 3.0 processor which I expect great things from. Its the 45nm series. I also have 2 gigs of DDR2 PC6400 800fsb Dual Channel OC memory in shipment. My problem is during my setup I formatted my harddrive for a clean install and when its close to being done I get this error message on the forbidden blue screen: STOP 0x000000A IRQL-NOT-LESS-OR-EQUAL. So I browsed through my BIOS checking settings and ran into this in PCU settings: cache 2x1024 memory. Assuming this could be changed I browsed some more changing settings and taking note of what I changed and what the original settings were,but never could disable the cache. It doesnt seem to be an option at all. I think this is my problem. I think the sytem is trying to access unaccessable memory to finish downloading XP, but I also took note when I was searching the net that it could be a driver issue. If anyone knows anything that may help me resolve this, or if you are aware of a way to disable the cache before downloading an OS, please let me know.
View 4 Replies
View Related
Nov 19, 2008
here is the problem: when I plug in an USB device, windows will install the driver for the device automaticlly if:
1. the driver comes with the system.
2. the device driver has been installed.
I wanna stop windows installing driver automatically but ask me the location of the driver when I plug in a device every time. How do I do that?
View 1 Replies
View Related
Aug 27, 2008
i am trying to install winxp on my wifes older computer....now it is older but it does meet all of the winxp hardware requirements for installation....3 times now it has seemed like it was going to take the installation but I keep getting different stop errors....the 3 I have gotten so far are 0x00000024; 0x000000D1; 0x0000008E .....does anyone know what is going on so i can install winxp already.
View 2 Replies
View Related
Sep 5, 2008
Is there any way in XP to install a device driver manually. I've tried using update driver in the device manager but it tells me I already have the best driver. If I unistall the driver, when I use the add hardware wizard, windows automatically installs its own driver.?
View 1 Replies
View Related
Feb 15, 2008
The computer uses XP home and is set for automatic updates.Every time I switch off it says it is installing update 1 of 1 even if I have not been connected to the net.When I tried using manual update I was told that the installation of <Windows Installer 3.1> had failed.Is the computer trying to install this same thing every time?If it is how do I get it to install properly or remove it from the list of programs ready to be installed?I think that when I installed the drivers for the motherboard this installer, or an earlier version, was installed by the Intel download.
View 11 Replies
View Related
Mar 13, 2007
I have been trying to fix this problem for about three days now, and I am at the end of my rope. I was installing the Kodak EasyShare Software and when it was almost finished, my PC restarted. I disabled the automatic restart and received the BSOD with the above mentioned stop code. I have rolled back all of my drivers and reupdated them. I have installed new drivers for my chipsets on my motherboard. I can go into Safe Mode with networking with no problems. But as soon as I start Windows normally I get the BSOD. I don't see anything in my startup folders either. I have ran a HiJack this file and found nothing either.
View 7 Replies
View Related
May 26, 2010
I'm in the middle of a basic networking lab and one of my VM's crashed. As our host, we use Windows XP. For virtualization we use VMware Workstation. I had a problem installing the Internet Printing Client for my lab. I got an error saying that there wasn't enough hard drive space. I then shut down my VM and added another hard drive. Upon startup I was greeted with: STOP: c0000218 {Registry File Failure} i did this:Removing the virtual HDD I added before the problems started. Restarting the VM. Restarting the host machine. Trying the VM on another machine. Booting to .iso and using the repair console with the command chkdsk C: /r.
View 1 Replies
View Related
Oct 5, 2010
Toshiba Satellite running on windows XP
When I start the computer, it asks if for the choice of Safe Mode, w/ Networking, w/Command Prompt or Normally.
I've tried them all and if I try it normally, it won't get past the XP loading screen. It's loading and then it flashes a blue screen for a second and then restarts the computer again.
I tried pressing F8 at boot and selected 'Disable automatic restart on system failure' and this is what I get
STOP: 0x00000024 (0x00190203, 0x83306788, 0xC0000102, 0x00000000)
I even tried using this http://forums.techguy.org/6669592-post28.html to get to chkdsk At boot, F12, chose CD/DVD, but still nothing, I even tried disabling boot from +HDD, FDD and LAN from the bios setup menu to see if it works and this is what I got, it just keeps going on and on unless I enable boot from +HDD
Intel UNDI, PXE-2.0 (build 082)
Copyright (C) 1997-2000 Intel Corporation
For Realtek RTL8139(X)/8130/810X PCI Fast Ethernet Controller v2.13 (020326)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.
View 7 Replies
View Related
Apr 7, 2006
I have seen a similar problem posted previously on this forum. But after reading it i think this is a different problem, so, here goes: I recently bought a new graphic card: Radeon all-in-wonder x1800xl. Installed it on a clean system (did a reformat before i installed). The problem occurs after usually 30-60 minutes of gaming (so far with oblivion, black & white 2). The game freezes for about 30 sec and then goes into blue-screen mode.
The message is as follows:
Kernel-Data-inpage-error stop error screen
then there are a lot of numbers etc.
I have sometimes noticed a slight change in fan noise prior to freeze (speeding up)
After reebot everything's back to normal.........
View 4 Replies
View Related
Jan 18, 2008
I have a celeron/p4 machine with 256 RAM and 160 G Hard Disk. Well i installed a service pack 2 for xp. After installing my screen freezed so i restarted the pc and I got a blue screen. What can i do please?
View 1 Replies
View Related
Oct 2, 2007
It was initially having problems loading her desktop and profile, sometimes rebooting itself several times after the log-in before successfully starting windows. I attempted to export the registry this morning in regedit and as soon as it started, it rebooted. Now it always gives a stop screen no matter what start up option I try stop: 0x00000024 (0x001902fe, 0xf89b16dc, 0xf89b13d8, 0xf8171f81) ntfs.sys - address f8171f81 base at f8122000, datestamp 41107eea
I downloaded the microsoft startup disks and even booting with all of them, when I type r for the recovery console it takes me right to the same blue screen. From what I've read it seems like chkdsk might fix things but I cannot get a command prompt. Perhaps the Maxtor harddrive is failing and I downloaded Seagate diagnostics for DOS because their windows version isn't going to help me since I can't start that. I booted off the disk and get a screen full of mostly general info but then it tells me the command interpreter is not found and wants me to give it the full path for command.com. It can't recognize anything I try to type here but I don't know what syntax to even use here. If I can come up with an ASR disk from another XP Pro PC, I'm wondering would running the automated system restore found on the first microsoft disk be an option? Is there any other way to get to run chkdsk because I can't even get into recovery console?
View 5 Replies
View Related
Aug 31, 2006
It happens typing OUTLOOK messages or messages on online forums. I'll be typing and suddenly everything freezes; but I keep on typing and about 5-8 seconds later the characters suddenly catch up.Seems this began after a recent Windows XP update, but I don't know. I've experienced it on my laptop as well, but since some of the same software is installed, could be that. I have VCom's Fix-It 6, but don't know whether that could be the problem or not. Oooops...did it just now.
View 8 Replies
View Related
Jul 27, 2008
I got the blue screen error code stop: c0000218 have no idea what this means.
View 1 Replies
View Related
Sep 7, 2005
I occasionally get a stop message and blue screen. It happens randomly, sometimes I am just on my desktop with no programs running. Here are some details:
STOP: 0x000000D1 (0x00000008, 0x00000002, 0x00000000, 0xF3C70140) atinyvxx.sys - Address F3C70140 base at F3C52000, Date Stamp 41f70216
View 4 Replies
View Related
Jul 30, 2010
i installed a new printer hp laserjet 4015 from the installation cd. previously 2015 version was installed. the installation went ok and the printing was also ok. system was shutdown normally. the next work day the system rebooted after the login was entered. this was solved by choosing 'last know good configuration' option of startup. however on re starting the same issued erupts. the system xp sp2 boots only when the last know good config option is chosen. the blue screen when opted for shows this error stop: 0x00000024 (0x001902fe, 0xf7a76854, 0xf7a76650, 0xa2c83692)
View 4 Replies
View Related
Nov 5, 2008
I've been having some issues with the DRIVER_IRQL_NOT_LESS_OR_EQUAL_TO_ZERO (0x000000d1) as well as IRQL_NOT_LESS_OR_EQUAL (0x0000000A)and STOP: 0x1000008e and 0x1000007f.I'm crashing only while playing games. The crashes seem to occur more often if I'm playing a game while running something else such as streaming a podcast. The crashes are also occuring with greater frequency with each day that passes. I reformatted after these started happening, and i replaced my RAM as well, as that seemed the most likely culprit.
View 14 Replies
View Related
Jun 28, 2005
I have borrowed a school computer for the summer, it runs XP. Today, when I booted it up, it displayed a blue screen with a stop message. "c0000135 <unable to locate component> winsrv was not found. I have spent the afternoon searching for a way to fix this, but all the windows help sites require you to download stuff, and since I can't get the OS to actually turn on, I obviously can't log on to a website.
View 4 Replies
View Related
May 15, 2008
I have been given a desktop with win XP Pro. it will boot to the log in screen and i do not know or have the password for the previous user. I have a legal copy of XP Pro and try to boot using the cd in the cd drive. it will run setup and load all the drivers and when it would normally start windows, i get the stop screen error. I have tried several boot disks with the same results. I tried Morphix (Linux) and a ERD with same results.
View 1 Replies
View Related
Jan 14, 2008
I have another long thread kinda ending up with this, but it died. The thread. Everyone ran away. This was long ago enough so I think posting again is not duplicating.Now, since getting this sytem around 6 mos ago. which now has new mobo---tho the original one was fine and now I have a spare and now good thermal paste, but the symptom manifested on both boards.I have, very occasionally been getting pool error stop screen.I was asked to post the speicific error with the premise that someone might understand the code and provide more info.i waited until it presented again.took pics and posted them. It has not presented since.I will now upload those again.if anyone knows wut this particular code means, that would be amazing. Cause I have done everything I can to find out, including on MS..and they have a page there which made me throw up, forget is not about my individual code.
View 14 Replies
View Related
Jun 25, 2010
I'm working on an HP 530 and when I boot up, it blue screens with a stop code.The code is 0x0000007B So far, I have attempted F8 w/o success, tested and swapped the RAM, and run checks on the Hard Disk.G-Parted can see and partition the Hard disk , but Windows Repair disk can't see the Hard Disk.I have re-imaged this unit and it completed successfully, but when I rebooted, it BSOD'd again.There is nothing in the BIOS to change it to IDE from SATA and the self-test is reporting no errors.
View 12 Replies
View Related
