Server 2008 C0000218 Stop Error: Installing The Internet Printing Client?
May 26, 2010
I'm in the middle of a basic networking lab and one of my VM's crashed. As our host, we use Windows XP. For virtualization we use VMware Workstation. I had a problem installing the Internet Printing Client for my lab. I got an error saying that there wasn't enough hard drive space. I then shut down my VM and added another hard drive. Upon startup I was greeted with: STOP: c0000218 {Registry File Failure} i did this:Removing the virtual HDD I added before the problems started. Restarting the VM. Restarting the host machine. Trying the VM on another machine. Booting to .iso and using the repair console with the command chkdsk C: /r.
laptop was infected with the Antivirus 2009 after surfing the web and I removed it using malwarebytes program. Then shortly after the laptop would show a blue screen, displaying "KERNEL STACK INPAGE ERROR" and then reboot. After the reboot, my laptop seemed to run fine, I downloaded AVG antivirus software to check if there was a boot sector virus (?) and after running the laptop for about 30 minutes, it showed the blue screen again and reboots. This kept on occuring.
Then I tried to reformat the laptop. The first time I tried to format it as FAT32, it got to about 60% before rebooting. The second time I managed to get past the formatting (FAT32 [quick])and I got onto the part of installing windows. About 20 minutes into the installation. A stop error appeared "STOP C0000218 Unknown Hard Error". Could the hard disk be corrupt
My computer keeps giving me this error when I start it up Stop: c0000218 Unknown Hard Error Unknown Hard Error I can boot it into safe mode, but I'm unable to really do anything with it. When I try to go on the internet I get directed to a Yahoo search of whatever I entered into the address bar... and any links clicked bring me to random pages. I also noticed that the address of the link in the search isn't showing up in the status bar.
I booted up my computer and got an error message saying "STOP: C0000218 {Registry File Failure} The registry cannot load the hive (file):System RootSystem32ConfigDEFAULT or its log or alternate. It is corrupt, absent, or not writable" I tried rebooting in safe mode, to no avail. Now I can't even get it to come back to the other "STOP" error screen because every time I boot up my computer a window pops up labeled "Dell PC Restore by Symantec" and states The Dell system recovery tool has detected an unsupported change in your master boot record. The tool cannot run at this time."
my laptop stopped working. After dwld some Excel service pack the pc refused to restart. The message is quite ominous: Stop error c0000218 and the hive affected is system root/system32/config/default It's impossible to recover the last working config or start in safe mode or do anything. It keeps looping back to the blue screen with the stop error. The pc does not recognize the hard drive, it does not have a recovery cd.
I'm gettting a blue screen when i try to start my laptop with Windows XP media. It's saying the registry cannot load the hive (file): /SystemRootSystem32ConfigSECURITY or its log or alternate. It is corrupt, absent, or not writable. I'm guessing I need the windows xp media reinstallation disk, but I can't seem to find it.
When I try to join a domain with a XP Pro client to a Windows 2K3 server and after going through Control Panel>System and entering the domain name and my Adminstrator credentials, I get "The following error occured when attempting to join the domain "computerlab.net": The account specified for the service is different from the account specified for other services running in the same process."The Administrator account for both server and client is identical if that affects it all? I seem to be very close to success except for this error message.
Installing windows on a pc built for my friend and it comes up with a stop code. stop d1. driver_irql_not_less_or_equal then it states
acpi.sys address fc40d3b4 base at fc3fb000
which i think refers to a stop a1 as well.
ive tried using 2 different type of memory on the m-board and still get the same error. there are no other hardware besides a cdrom and hdisk, mosue and keyboard. i did have an old logitech mouse but swapped that as i read that can cause problems too.
i dont know how to go about fixing this as their is a hotfix for acpi problems but thatr equires u to actually have windows on teh pc in teh first place i.e safe mode.
i can get into bios and it performs POST no problems. the only other thing is it boots fromcdrom but it says no emulation.
Over the last two weeks, I've reinstalled Windows five times. I'm literally at my wits end. Here's my problem...
Whenever I try to install almost anything, I get Stop error 0xF4, which is the termination of a system-critical process or thread. Sometimes it happens for no reason, but for the most part, it's usually just when I'm installing something. Unfortunately, I don't have all the parameters of the stop error, but according to the Overclockers Forum, my first parameter (0x03) denotes that it is a process that is being terminated.
There are sometimes when the sfc /scannow command can temporarily fix the problem (that is, to run it before installing an app, then install the application once it is finished) but that's not always the case.
It should also be noted that there are some instances when I get a 0x7A error, but this is seldom. I merely included it in the event that it may prove to be helpful.
I'm running Windows XP Home, with an ASUS A8N-VM-UAYGZ motherboard. I'm sure you guys need more specs than that, and if so, please tell me. Also, I intended to include the Stop error message in it's entirety, but I neglected to write it down (odd, since I've seen it 40+ times). So I will write a follow-up with the Stop error and ...
Recently I bought a very cheap Acer Aspire M1640-E1150 which came with an MSI motherboard, an Intel Pentium Dual Core E2200, 2 GB of DDR2 RAM, and a 320 GB HDD from Hitachi. The system came with Vista initially installed on it, and needless to say, it was very slow! I decided to do the right thing and go to XP, so I found all the drivers required and I proceeded to install Pro from a disc that I have from a previous computer. As soon as the screen booted up and the system was being checked by the program, the system gave me an error message, before I even got to partition anything, it was initial. I tried to restart, took one of my RAM sticks out, but nothing was working. I even tried to format the HDD through an external drive, but nothing was working.
The error message is "Stop: 0X0000007B" and something about a virus or a software or a hardware being the problem. The system was running smoothly on Vista, and I even formatted the C drive, and I am sure that there were no viruses.
STOP: C0000218 {Registry File Failure} The registry cannot load the hive (file):System RootSystem32ConfigSECURITY or its log or alternate. It is corrupt, absent, or not writable I got this on a screen last night.
one of my friend is having a problem with his Fujitsu Siemens Laptop (Win XP - Dot know the SP), whenever the laptop starts it shows the blue screen and restarts itself, so there is jo way you can login to the win xp, the following msg is displayed on the blue screen. the error is in Polish Language but i guess you can understand the error by the path it is giving
STOP: c0000218 {AWARIA PLIKU REJESTRU} NIE JEST MODLIWE ZAEADOWNIE PREZ REJESTR GAE-ZI (PLIKU): SystemRootSystem32ConfigSAM
I get a blue screen with following error. STOP: C0000218 {Registry File Failure} The registry cannot load the hive (file):System RootSystem32ConfigSECURITY or its log or alternate. It is corrupt, absent, or not writable. I tried starting in Safe Mode same error! Also tried starting with Last Known Good Configuration again same error!
I put in My CD and it goes through the first blue screen (the one where is asks if you want to press f2 to do install drivers via A drive etc) and when it gets to "Setup is Starting up windows" (this is before all the HD formating and partitioning) I get the blue screen. it does not have much info on it all it says is:Stop: 0x0000007B (0XF78D2524, 0XC0000034, 0X00000000, 0X00000000)
I have been trying to fix this problem for about three days now, and I am at the end of my rope. I was installing the Kodak EasyShare Software and when it was almost finished, my PC restarted. I disabled the automatic restart and received the BSOD with the above mentioned stop code. I have rolled back all of my drivers and reupdated them. I have installed new drivers for my chipsets on my motherboard. I can go into Safe Mode with networking with no problems. But as soon as I start Windows normally I get the BSOD. I don't see anything in my startup folders either. I have ran a HiJack this file and found nothing either.
Ok, using this help website, http://xphelpandsupport.mvps.org/how...air_a_stop.htm I am at the harder method, but encountered some problems.md tmp(nothing really happened not sure if anything was supposed to) copy c:windowssystem32configsystem c:window mpsystem.bak (copied fine) copy c:windowssystem32config software c:windowmpsoftware.bak (it says the file can not be copied). Do I go on with the rest of the tutorial, or where exactly do I go from here? Is there any possibility that I will not have to reformat and get my old computer back?
I have just installed a Samsung CLX-2160 on my Dell Dimension 5150 PC,which runs Windows XP Media Centre.As soon as the PC started reading the installation CD, it crashed with the following (taken from event viewer):The computer has rebooted from a bugcheck.The bugcheck was: 0x0000007e (0xc0000005, 0x804f106f, 0xba4fbaac, 0xba4fb7a8). A dump was saved in: C:WINDOWSMEMORY.DMP.
I rebooted with F8 and chose last working config.After a little enlightened guesswork and advice I removed my old Dell 725 printer driver(which had started giving an error message on startup). Now I could load the Samsung driver etc and the new printer works.However, XP still crashes whenever I reboot normally I can still bring up a working system with F8 as above (but I have to reload my PCI card drivers again - 2 port serial and sound card - for some reason)
I received the following error message yesterday morning when I attempted to access the internet via Internet Explorer:Microsoft Visual C++ Runtime Library Runtime Error! Program: D:Program FilesInternet Exploreriexplore.exe This application has requested the Runtime to terminate it in an unusual way. Please contact the application's support team for more information. Hitting 'OK' or closing the window makes another error message pop up: Server Busy This action cannot be completed because the other program is busy. Choose 'Switch To' to activate the busy program and correct the problem.
Everytime i boot my comp i get the same things happening. I let windows load and get a BSOD just b4 i get to my account logon. The BSOD states: STOP: c0000218 (Registry File Failure) Registry cannot load hive (file): SystemRootSystem32ConfigSoftware or its log or alternate. Corrupt, absent, or not writable. Ive tried to work around it by using my Windows XP Home SP2 disk and booting from that but then i get stuck in the loading process of the disk saying that: aic78xx.sys is corrupt press any key to continue
When I start PC, it automatically takes me to the startup options part to reboot in safe mode, safe mode w/ networking, safemode w/ prompt, last known good config, & normal startup. Getting Stop c0000218 {Registry File Failure} The registry cannot load the hive (file) SystemRootSystem32Config
I install Server 2003 Standard SP1 downloaded and installed on a PII 400, 256Mb RAM with IIS, ASP.Net 2.0, SQL server 2000 SP4, Mysql 5, and PHP5, and all without a single hitch...too good to be true. I went ahead and tried on what will be my server PIII600, 512 MB RAM, First try, Server 2003 couldn't find a file when installing, retried and it worked. Downloaded SP1 and when I was extracting it said "file is corrupt", downloaded 4 more times with same result. reformatted and reinstalled 5 more times and cannot get past "file is corrupt" on SP1 and sometimes extracting the .Net 2.0 installer got the same error. I swap all hardware with PC from first try (except RAM, Mobo, CPU, CDROM) with no change. Win98 and XP installed fine on the second PC just can't get server 2003
windows 2000 pro, seems to run ok until you try to get on the internet. you can get around on it ok going to control panel you can download programs etc but the min you plug in a network cable you really even need to doubleclick on the internet if you wait a few seconds after you plug in the network cable right away a blue box pops up with this stop error Stop 0x0000001E (0xC0000005) and then three more sets of all zero's KMODE_EXCEPTION_NOT_HANDLED.
We rebooted the computer yesterday and when it all came up i had the followin error. xlm page cannot be displayed. underneath it has the following ///c:/documents and settings/candy/localsetting/temp/mr... Does this mean anything to any one.
Alright this is the first time I see something like this:i am working on a client's pc an I cannot connect to the internet.
PC specs: Compaq, Presario M2000. XP HOme.
Both the Local and Wireless connection gave a message saying the network didn't assign the computer an IP Address.So I went to Properties, Internet Protocol (TCP/IP) and manually assigned both the IP address, Subnet Mask and Dafault Gateway, so now the Local area it's connected and the wireless too (with excelletn signal). but I am not able to go online yet
My system is slow, Malwarebytes came back with error 714 (0,9), so uninstalled using add/remove programs - but even that continually showed error code thru process. Have now reinstalled Malwarebytes and running scan - nothing detected on scan yet. Tried to print on Dell 924 Photo printer (which has worked fine for 5 years) and came back printing error. Tried to add/remove MS SQL 2005 program, wouldn't allow me to uninstall. this program had error messages at startup, wasn't even sure what it was or how it got on the system, so decided to uninstal after inquiring on techguy software forum. but it wouldn't let me uninstal it. I think the program was probably related to high school technology class with the boys.
How do you do this please? its not a prob with my printer, I think I remember adjusting something in windows but can't remember how. I print out a page off the net, but a portion of the right hand side is always missing .. What is the solution to fixing that please??
When booting up my PC, I am receiving the following error message 'STOP: c0000218 {Registry File Failure} The registry cannot load the hive (file): SystemRootSystem32ConfigSOFTWARE or its lor or alternative. It is corrupt, absent or not writable'. I understand that the OS needs to be recovered from the XP bootup disk but the OS was pre-installed so I do not have a copy of this.
Im getting: Stop c0000218 {Registry File Failure} The registry cannot load the hive (file) SystemRootSystem32Config|SOFTWARE or its log or alternate and it goes on to say how its dumping physical memory.
I cannot bootup the computer. It gives me the following error STOP:- c0000218 Registry file failure. The registry cannot load the hive (file) or systemrootsystem32configsecurity or the log or alternate. It is corrupt, absent, or not writeable. Cannot boot to safemode, also tried last known good configuration without success. I have also tried the microsoft KB 307545 fix but could not copy or delete the security file.
