I have seen a similar problem posted previously on this forum. But after reading it i think this is a different problem, so, here goes: I recently bought a new graphic card: Radeon all-in-wonder x1800xl. Installed it on a clean system (did a reformat before i installed). The problem occurs after usually 30-60 minutes of gaming (so far with oblivion, black & white 2). The game freezes for about 30 sec and then goes into blue-screen mode.
The message is as follows:
Kernel-Data-inpage-error stop error screen
then there are a lot of numbers etc.
I have sometimes noticed a slight change in fan noise prior to freeze (speeding up)
After reebot everything's back to normal.........
When I start the computer, it asks if for the choice of Safe Mode, w/ Networking, w/Command Prompt or Normally.
I've tried them all and if I try it normally, it won't get past the XP loading screen. It's loading and then it flashes a blue screen for a second and then restarts the computer again.
I tried pressing F8 at boot and selected 'Disable automatic restart on system failure' and this is what I get
I even tried using this http://forums.techguy.org/6669592-post28.html to get to chkdsk At boot, F12, chose CD/DVD, but still nothing, I even tried disabling boot from +HDD, FDD and LAN from the bios setup menu to see if it works and this is what I got, it just keeps going on and on unless I enable boot from +HDD
Four or five months ago I installed a new HD in my Dell Inpiron 700m laptop. I used Acronis True Image, as I've done previously with my Latitude. Initially, I had some trouble, because apparantly one or two drivers were missing. I found a discussion about this online and ran through the steps to fix the problem and everything seemed fine. A couple days after the installation I received the blue stop error screen for the first time. Restarted the computer and hadn't had it appear again until last week. The other night, it was coming up every five minutes, shutting down the computer.
About a week ago, I performed a fresh reinstallation of Windows XP Home (I posted here about it) in order to allow it to work with my new motherboard. Since then, everything had been working fine until I experienced a sudden Blue Screen of Death, yesterday, while playing the game 'The Chronicles of Riddick: Escape From Butcher Bay'. I rebooted and attempted to play the game again, but experienced another almost identical Blue Screen at a different point in the game.
I get this almost everyday, I even restored the laptop to how it was out of box and it keeps crashing. Here is the error.MULTIPLE_COMPLETE_REQUESTS ***STOP: 0x00000044 (0x862df368, 0x00000D60, 0x00000000,0x00000000)
I'm getting a BSOD with the following Stop Error DRIVER_IRQL_NOT_LESS_OF_EQUAL *** STOP:0x000000D1(0x00000018,0x00000002,0x00000000, 0xF72BD25F) iastor.sys - Adress F72BD25F base at F72AE000 DateStamp 42b2df42 This happens every time I start up and also I am unable to boot into Safe Mode as it is getting hung on whatever file is after Mup.sys.My plan was to go into safe mode and update iastor.sys to a newer version but I cant. I also find it stange that this file is an issue as I only have a single hard drive and I was under the impression that this file had something to do with RAID.
2 months ago I ordered system from Cyberpower PC and it was shipped a week later.Set it all up,formatted Windows XP Home Edition and got it running. Shortly there after, I started blue screening and it seemed RAM related, so I swapped the sticks and it seemed I would only BSOD with one of the sticks, so I called the company, shipped it back, and got a new stick.
Then I started to BSOD again with the error message of IRQL_LESS_OR_NOT_EQUAL and then 0x0000000A (0x0000F78A, 0x0000002, 0x0000001, 0x806E4A8F), and this particular error would only occur while I was playing World of Warcraft. So first I pulled the new stick of RAM and tried playing... and everything went fine for a day, and then I BSOD'd again, same error
Man, my computer for the last two weeks have been crashing like an emo. I mean, when I play GTA: San Adreas, in 20 minutes, I get a BSOD with a stop error. When I put hardware acceleration to full, in a half an hour, I get a BSOD with a similar error. Believe me, I got three kinds of errors, and some were from different time. I believe the problem either came from the either the PSU, new 512 mb of ram, old 512, CPU, system board, or the graphic card. I'll try to post the error as best as I can. So, is there a solution to this? Error Message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER (Q293078) This is one of them, but there another one with KMODE that I can't seem to remember. Also, sometimes, after it tries to recover from a serious error, the computer shuts down during the bootup before I can choose which XP version I can choose. Also, I hate to say this, but I'm not using a legit windows copy sp1, but I have updated to sp2.
I have a problem J, I cant get XP to boot up. My pc blue screens mid way through the loading windows screen and then re-sets. I had a GPU hardware failure, after windows automatic installed some software a month or so ago (not sure what it installed as I wasnt using the pc at the time). My pc would not post and the mbos gave a GPU beep error message. I have just brought a new GPU and now I can get to the pc to part load. Tried using my recovery cd, but that only gets half way and then blue screens with a STOP 0x000000c2 error. I think its a driver issue but as Im unable to get into the recovery to troubleshoot further, im not sure what I can do. The only thing I can do is rig up my pc hd to my laptop as a slave, does anyone know any software that can check an OS that not being used on a hd? Is there anything else I can try? I have flashed the BIOS to the latest version.
My granddaughter downloaded some kind of game on my computer yesterday she said that while she was playing a box came up and the screen went blue well it has been blue ever since the error Disable or uninstall any anitvirus disk defragmentation or back utilities Check your hard drive configuation and check for updated drivers Run chksk/f to check for hard drive corruption and then restart your computer techincal info stop:oxooooo24(oxoo190203,0x81364008 ,oxcooo102 ,oxooooooo)
My computer keeps giving me this error when I start it up Stop: c0000218 Unknown Hard Error Unknown Hard Error I can boot it into safe mode, but I'm unable to really do anything with it. When I try to go on the internet I get directed to a Yahoo search of whatever I entered into the address bar... and any links clicked bring me to random pages. I also noticed that the address of the link in the search isn't showing up in the status bar.
I put in My CD and it goes through the first blue screen (the one where is asks if you want to press f2 to do install drivers via A drive etc) and when it gets to "Setup is Starting up windows" (this is before all the HD formating and partitioning) I get the blue screen. it does not have much info on it all it says is:Stop: 0x0000007B (0XF78D2524, 0XC0000034, 0X00000000, 0X00000000)
Toshiba Laptop My buddy just came over and has his Toshiba Laptop and it is having a blue screen stop error. Wanna see if we can get some help.He has windows 2000.you turn it on and it goes through every thing and then you put your password in and get to the desk top and all that is ok, when you click to get on the internet it would flash a blue screen and then shutdown. I went into system and advanced and unchecked auto reboot so now it doesn't shut down but you get the blue screen and you can't go anywhere when it comes up.
having my laptop returned from service I found my Bios messed with where when I would start my computer but Bios wouldn't find my hard drive or an OS I found that my system was set to RAID instead of ATA. After resetting it back to ATA it boots up fine. However I wanted to reformat and start clean.I placed my XP disk in, reset my BIOS to read my optical drive first and no problems.However every time I get to partition drive all I see is "Unknown Device" If I press any key I get a blue screen of death. Most times it's the 0X0000008E.
I have just installed a Samsung CLX-2160 on my Dell Dimension 5150 PC,which runs Windows XP Media Centre.As soon as the PC started reading the installation CD, it crashed with the following (taken from event viewer):The computer has rebooted from a bugcheck.The bugcheck was: 0x0000007e (0xc0000005, 0x804f106f, 0xba4fbaac, 0xba4fb7a8). A dump was saved in: C:WINDOWSMEMORY.DMP.
I rebooted with F8 and chose last working config.After a little enlightened guesswork and advice I removed my old Dell 725 printer driver(which had started giving an error message on startup). Now I could load the Samsung driver etc and the new printer works.However, XP still crashes whenever I reboot normally I can still bring up a working system with F8 as above (but I have to reload my PCI card drivers again - 2 port serial and sound card - for some reason)
I was working on my computer, Windows 2000 Pro.I was moving my foot under the desk and accidentally switched off the surge protector.I turned the protector back on and restarted my computer.I get a royal blue screen that says Stop Error.Inaccessible Boot Device.None of the F8 options work for restart, they all say the same thing.I really don't want to have to reformat.
I'm gettting a blue screen when i try to start my laptop with Windows XP media. It's saying the registry cannot load the hive (file): /SystemRootSystem32ConfigSECURITY or its log or alternate. It is corrupt, absent, or not writable. I'm guessing I need the windows xp media reinstallation disk, but I can't seem to find it.
Encountered a Blue Screen of Death error. The error stated that I should run Chkdsk and then proceeds to restart and bring me to the Windows boot selection screen (safe mode, last known good configuration, normally). No matter which choice I pick, it always leads to the BSOD then restarts. Since this is getting me nowhere fast, I want to just format and reinstall windows. I do not have my recovery CDs, and when I enter the BIOS to change the boot sequence I cannot change it so the CD drive is above the hard drive in priority. The reason it gives me in the bios is that "All items on this menu cannot be modified in user mode. If any items require changes, please consult your system supervisor. Any ideas on how I can boot off the cd and reinstall windows from scratch?
The start of my problem is that I was receiving an error 'cannot initialize lsass.exe service'.After repairing XP SP2, the following is displayed every time that I boot:SAFE Mode - black screen with 'safe mode' in bottom corners of screen Windows Mode - blue screen.The mouse is responding.There are no icons.There is no text (except for 'safe mode' as above)CTRL/ALT/DEL does not display task manager.CTRL/ESCAPE does not display anything.Clicking on various parts of thescreen has no effect.I have replaced Explorer.exe from c:i386
I couldnt start up windows. It would hang at the windows loading screen and go no further. So I was told to try a repair-install. And thats where even more trouble has started. So I started to repair-install. During the Windows Install setup, it gets almost to the point of being completed, but gave me a blue screen error STOP message at around the "18 minutes left" mark. During "Registering components". It would do this every time at the same spot. So I searched a bit about how to solve the problem. One suggestion I found on the interwebs was to try it with only one stick of ram installed, I have four overall at 2gb. So I tried that, next time I boot up to the comp, it loads up the bios, and then goes to the black windows loading screen with the loading bar, then starts with a blue screen saying "Setup is being restarted" So I figure its restarting my windows installation since it never was completed, after that message, the screen goes black with a cursor, and stays that way forever. I immediately put all the ram back in, and no luck, same thing. I tested each individual ram stick, same thing, just goes black. So now, I can't even seem to re-install windows. Did my hard drive just crap out? Some hardware issue? Im already thinking about buying a new fresh hard drive, installing windows on there, and just moving all my files from the old hard drive over to the new one. Though that would be a pain, I really want to save my current drive! And all the data on it.
I occasionally get a stop message and blue screen. It happens randomly, sometimes I am just on my desktop with no programs running. Here are some details:
STOP: 0x000000D1 (0x00000008, 0x00000002, 0x00000000, 0xF3C70140) atinyvxx.sys - Address F3C70140 base at F3C52000, Date Stamp 41f70216
i installed a new printer hp laserjet 4015 from the installation cd. previously 2015 version was installed. the installation went ok and the printing was also ok. system was shutdown normally. the next work day the system rebooted after the login was entered. this was solved by choosing 'last know good configuration' option of startup. however on re starting the same issued erupts. the system xp sp2 boots only when the last know good config option is chosen. the blue screen when opted for shows this error stop: 0x00000024 (0x001902fe, 0xf7a76854, 0xf7a76650, 0xa2c83692)
I've been having some issues with the DRIVER_IRQL_NOT_LESS_OR_EQUAL_TO_ZERO (0x000000d1) as well as IRQL_NOT_LESS_OR_EQUAL (0x0000000A)and STOP: 0x1000008e and 0x1000007f.I'm crashing only while playing games. The crashes seem to occur more often if I'm playing a game while running something else such as streaming a podcast. The crashes are also occuring with greater frequency with each day that passes. I reformatted after these started happening, and i replaced my RAM as well, as that seemed the most likely culprit.
I have borrowed a school computer for the summer, it runs XP. Today, when I booted it up, it displayed a blue screen with a stop message. "c0000135 <unable to locate component> winsrv was not found. I have spent the afternoon searching for a way to fix this, but all the windows help sites require you to download stuff, and since I can't get the OS to actually turn on, I obviously can't log on to a website.
I'm working on an HP 530 and when I boot up, it blue screens with a stop code.The code is 0x0000007B So far, I have attempted F8 w/o success, tested and swapped the RAM, and run checks on the Hard Disk.G-Parted can see and partition the Hard disk , but Windows Repair disk can't see the Hard Disk.I have re-imaged this unit and it completed successfully, but when I rebooted, it BSOD'd again.There is nothing in the BIOS to change it to IDE from SATA and the self-test is reporting no errors.
The Technical Information is this: *** STOP: 0x0000008E (0xC0000005, 0x00000000, 0xF2F22A50, 0x00000000) I'm getting tired of this happening every day.
well i just installed trial version of webroot spysweeper and then i go on to TSG then my computer goes all blue and it says things about dumping files on disk or something
I built a pc back in Apr 2005 and it has been a nightmare from the 1st day. Ive reformatted twice only to encounter the same problems. BLUE SCREEN CRASHES AND STOP ERRORS. This occurs during every single task I attempt. I am not even able to run a virus scan without it crashing. There are a few yellow ?? in the system device menu box thingy but the drivers wont install. It seems that every blue screen crash has a different code and always end with system dump.
I was able to use ad-aware SE to remove the spyware garbage but it didnt help. I did a chkdsk /f and there were many, many bad sectors on the hard drive a majority of them are system32/dll (upside down LL) Cache dll (again upside down LL)files, I ran the scan several times and each time many many bad sectors were found from what I can tell new bad sectors with each scan. What does this mean.
No matter what program I try to use about 5 minutes into it the pc will blue screen crash. It doesnt matter what its is looking at the system device manager, trying to update drivers. I everything I do CRASHES.I cant even get my important data off of the pc & onto a cd without it crashing. I dont know what to do. I can download something on a different pc test to ensure its working right then put it on this pc and I get a message saying that some file is corrupt or it will crash. It doesnt matter what it is a few minutes into it the system crashes. Even when try to run software of the mobo cd still crashes I tested the memory and 1 test program says it passed and another test program says it failed.
