Realtek PCIe GBE Network Controller Cannot Start Code 10
Sep 15, 2014
first off this is a new fresh install of windows 8 i had to download and install 8.1 via updates. This computer is fully updated.
It is an older computer but I only use it for my TV to store Movie/Videos
ASUS M3A78-EM
AMD Phenom 8450 @ 2.1ghz
2gb gskill ram
blueray drive
3tb seagate
2tb wd
kingston 120gb SSD
after a fresh install everything worked fine until i tried to connect to my local network the onboard NIC has an error (code 10) it is a Realtek PCIe GBE Family NIC. after finding this i uninstalled and went to Realteks website and got the newest windows 8 64bit drivers. ran the install and it updated the drivers... but the device still cannot start so i uninstalled again and picked the drivers manually and that didn't change the issue either.
So i checked the back of the computer and noticed that non of the activity lights were lighting up on the NIC so i pulled the ram and battery AND power cord and let it sit. (ive delt with a similar issue before where a NIC would stay asleep and not wake up) after a wait i turned it back on and noticed that i had an orange light glowing again on the NIC.
After setting up the bios i booted back into windows only to see that as SOON as the driver were automatically installed the lights in the back go out and of course..... the device cannot start error.....
At this point I cant think of anything else to do. I do have a wireless card in the pcie slot that works fine. could that cause the onboard not to work? or... am i Just SOL and this is just a Windows 8 issue? should i just go and buy a PCIe network card?
View 5 Replies
ADVERTISEMENT
Nov 18, 2012
I am using Windows 8 Professional. I am using a Dell XPS 1510 and am using a PCI Express Realtek PCIe GBE Family Expresscard.
I have already downloaded the latest driver from Realtek from 09/26/12. I have ran Windows Updates. No matter what the Realtek PCIe GBE Family Local Connection loses internet connection.
This card worked fine for months in Windows 7 Pro. The card works fine in Windows 8 Safe Mode. However, when logged into Windows 8 in normal mode, the card will allow and have internet connection for 1 min 12 secs to 1 min 32 secs, at which point the internet connection drops. The wifi and internal NIC (10/100) connection work fine. I've changed the NIC binding order. I've disabled the internal NIC, and Bluetooth (just in case) in the BIOS. I've tried uninstalling the WiFi to force using the Realtek PCIe GBE Family card.
I have ran procmon in order to try to figure out what if any application runs within the 1 min 32 sec timeframe that may interrupt the Realtek PCIe GBE Family card and have uninstalled any suspected applications. I've tried disabling services one at a time to see if it makes a difference.
I have tried DHCP and Static IP addresses.
The problem seems to be something within Windows 8. Something with Windows 8 disables the Realtek PCIe GBE Family internet connectivity. I've tried everything to keep the connection alive, internet works fine, I get perfect gigabit level speeds up until the 1 min 12 secs to 1 min 32 secs then all I get is no network connectivity.
The Windows 8 Troubleshooter is useless. Even though it is setup with static IP it says it can't find the default gateway. The issue is not with the router, somehow not being compatible with Windows 8 or something else. The card worked fine with the same router in Windows 7 and the internal NIC card works with the router in Windows 8 so its not that the router has problems with Windows 8.
I've also already disabled the "Allow the computer to turn off this device" option in the cards Power Management tab (first thing I tried). I've set the Power Management options on the laptop to be set to Maximum Performance.
Everything else with the laptop in Windows 8 seems fine, only this PCI express card that enables gigabit connection is failing. Don't want to use the slower WiFi or 10/100 connection those are too slow for what I need.
View 2 Replies
View Related
Jan 19, 2014
In the device manager, under memory technology devices, I have Realtek PCIE CardReader Properties displayed twice. The two locations are: PCI bus 2, device 0, function 0; and PCI bus 2, device 0, function 1. Dell offered a driver update for the cardreader which I installed. Only 1 of these 2 actually updated.
My question is do I need to update both or is one enough?
View 1 Replies
View Related
Feb 4, 2013
an error message in Device Manager when installing the network attached storage drives like MyBook Live, the drives themselves seem to work fine and i have access to them (most of the time) on my home netwok, however i keep getting that little yellow triangle telling me that something is wrong, specifically:
the device manager error code is This device cannot start. (Code 10)
View 1 Replies
View Related
Feb 5, 2013
I have two computers:
LOFT
mapped network drives M, N, O
BEDROOM
mapped network drives P, Q, R
If I am on the LOFT computer i can see all mapped network drives, M,N,O,P,Q,R
if I am on the BEDROOM computer I can see mapped network drives P,Q,R but not M,N,O. I click on M,N,O and it comes up with a windows asking for login and password and states the following, "the system cannot contact a domain controller to service the authentication request, after I type in the info I can then see the drives.
View 9 Replies
View Related
Jan 19, 2014
What is going on with my network connection. I have tried updating the drivers, refreshing my computer, installing all updates.
Type of computer: HP Pavilion 20-b010
Code:
Windows IP Configuration Host Name . . . . . . . . . . . . : Desktop Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : NoWireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Wi-Fi Direct Virtual Adapter
[Code] ....
Ethernet Adapter: Realtek PCIe FE Family Controller
View 9 Replies
View Related
Dec 30, 2013
I got a speed camera detector thing for Xmas. I've downloaded the software for the device and when I plug the device in, the software doesn't detect it. The manufacturer sent me an email with a link to download and install the driver. The driver installed, but it still doesn't work. When I looked at the driver status in device manager, it says...
This device cannot start. (Code 10)
{Not Enough Quota} Not enough virtual memory or paging file quota is available to complete the specified operation.
I'm on a windows 8 HP Pavillion 15.
View 1 Replies
View Related
Aug 19, 2014
In my network 4 Desktop running windows XP all are connected LAN cable and my modem is tplink and 1 laptop running windows 8.1 pro accessing network through wireless in my laptop network place all the pcs are visible but I am not able to ping them and when I click I am getting message that Network path not found Error code 0x80070035
View 2 Replies
View Related
Nov 23, 2013
I have to PC's that belong to the same homegroup. When I go to explorer, there is a delay before the other PC shows up and yet another delay when I select to browse that PC. If I close and go back I'll often get this error code and then there are time when I get the code on the first try. These PCs are running Windows 8.1 Pro and powered on 100% of the time. I noticed this nonsense while on Windows 7 as well.
View 7 Replies
View Related
Nov 3, 2013
I'm having trouble with my HP laptop. I've had this happen before and I had to completely reset my laptop because of it.
Basically I went to log in this morning, it said my profile couldn't be found and signed me out. I then tried again to log in and the Start menu has been flickering continuously and I can't select anything, it has also 'lost' all of my stuff so it looks like a temporary profile..
I have tried googling for an answer and cannot find anything that works, when I try to 'refresh' my laptop via going to safe mode it comes up with the error code: 80070490. I've tried to do a 'clean boot' in safe mode but that won't work properly..
View 7 Replies
View Related
Jun 11, 2013
I'm have a problem with a high definition audio device, it says This device cannot start. (Code 10). I have tried updating the driver and deleting and reinstalling the device, nothing has worked.
I can hear sound, but I can not record anything. I have tried several recording devices, like Audacity and MS Recorder and nothing works.
I have attached captures of my computer information.
I run Windows 8, 64 bit. The computer is only six months old.
View 8 Replies
View Related
Dec 5, 2013
I am making applications with Live code in Windows 8 and when saving them as exe's they were launching then due to some bad code I had to end the explorer process and reboot my PC and now when I try to run these programs I get the error The application was unable to start correctly (0xc0000142). Click OK to close the application.I tried using sfc /scannow and it found errors but could not repair them.
I have uploaded the log file. With system restore as a last resort.
[URL]...
View 1 Replies
View Related
Apr 5, 2013
i Am trying to build my first PC with a Asus P8Z68M motherboard I have managed to get it all going but when I start it up its says - Using PCIE Gen 2 - cant find any device. What does this mean? Also, why does the PC beep at me whilst booting up?
View 9 Replies
View Related
Sep 15, 2014
I have a newly home built MSI AM1i motherboard and have it running fine with Windows 8.1. I am trying to expand the number of SATA ports it has (comes with only 2). The mobo has a mini-PCIe card slot.
I purchased a AsMedia 106x, 2-port, mini-PCIe card (had to use a ribbon-cable extender to get it connected).
That all appears to be fine. I struggled a bit with drivers, but eventually found a Windows 7 AsMedia 106x driver set. Loaded that, seems ok.
Problem: When I go to device mgr, it does not see the added 2-ports. When I first boot up, during the black-screen phase, it does report that the AsMedia device is loading and will actually find/name a hard drive that I attach to one of the new ports. It then almost looks like it will load windows, give the nice little blue windows 8 flag and just sits there. I can hear a drive cycle every 2-3 seconds, but nothing.
I eventually have to hit the power button to shut down. If I disconnect the drive added to the new card, it will start up. The AsMedia device looks to load during a black-screen phase, but reports no device found, and then loads Win 8 Correctly. When I get in, again, no SATA ports shown for the new device.
View 3 Replies
View Related
Apr 23, 2014
My Windows 8.1 installation started developing some problems including malware. So I decided to reinstall Windows, but in order to make it without a hurry, I used a separate disk. This way I could use the old installation for everyday work until the new installation was ready for the switchover. But, I didn't have a spare SATA hard disk to start with, so I decided to use an old IDE hard disk.
My motherboard Asus P8H61 doesn't have an onboard IDE controller, so I used a Logilink IDE/SATA PCI-E card (JMicron JMB36X chipset) to connect the disk. I then managed to transfer some data to other places and freed a spare 500GB SATA disk so I could clone the installation since the old IDE disk was only 120GB. I used Acronis True Image 2014 and did an "As is" clone to make sure that the transfer would be successful and bootable. I would later extend the partition to take all the available space. So far so good.
The problem is that the disk works only connected on the Logilink card (JMicron JMB36X controller) and not when connected onboard (Intel controller). I attempted to repair Windows startup using the DVD-ROM but didn't manage to start Windows successfully, unless I connect the disk on the card. I wouldn't mind too much about it, but the card sometimes blocks when there are too many programs open increasing disk access freezing the system and I have to reset the computer. Not really convenient.
So what can I do to make the installation usable on the onboard Intel controller? Is there any workaround? Of course I would like to avoid reinstalling everything and waste a week's effort!
View 2 Replies
View Related
Oct 21, 2013
Since I updated to Windows 8.1 I cannot get my PC to charge my controller. Is there anyway to get the driver I need to enable my PC to do this again?
View 9 Replies
View Related
Mar 8, 2013
Why does every new O/S decide to remove undesired drivers and software? Same thing happened when moving from XP to Vista, and once you had Vista you sure had to get out of it!
Win 8 Pro N has physically deleted 3 multimedia controller drivers;
1. Type: Other unit, Mfg: Unknown, Location: PCI-bus 1, unit 0, function 0
2. Type: Other unit, Mfg: Unknown, Location: PCI-bus 1, unit 2, function 0
3. Type: Other unit, Mfg: Unknown, Location: On Microsoft ACPI-compliant system
Also, why hasn't Microsoft Fixit 50548 been adapted for Win 8 (i e possibillity to print picture or graphics to printer by right-clicking on file, then left-klick on Print on Menu that appeared. Also works to list contents of a drive on a printer output.
View 1 Replies
View Related
Mar 7, 2014
I am running into a problem with newly upgraded windows 8 computers not being able to register DNS with our existing domain controller that is currently on server 2003.
I am getting the following error: The system failed to register host (A or AAAA) resource records (RRs) for network adapter with settings:
Adapter Name : {0D2F7524-B997-4850-BE6E-50B502FE46A8}
Host Name : ########
Primary Domain Suffix : #####.#######.com
DNS server list :
172.29.1.10, 172.29.1.12
Sent update to server : <?>
IP Address(es) :
172.29.5.145
The reason the system could not register these RRs was because of a security related problem. The cause of this could be (a) your computer does not have permissions to register and update the specific DNS domain name set for this adapter, or (b) there might have been a problem negotiating valid credentials with the DNS server during the processing of the update request.
You can manually retry DNS registration of the network adapter and its settings by typing 'ipconfig /registerdns' at the command prompt. If problems still persist, contact your DNS server or network systems administrator. See event details for specific error code information.
I blanked out the computer name and domain name.
View 5 Replies
View Related
Sep 15, 2014
This evening I went to use by portable USB drive and noticed it wouldn't work. I tried another port and it still didn't work. I then tried another device on the same ports and it also did not work.
I opened up device manager and saw that my VIA USB xHCI controller was no longer listed under USB controllers. I turned on Show Hidden Devices and it then appeared as a hidden device. I attempted to re-install the drivers for it but the installer wouldn't run because it said it didn't detect the hardware on the system.
I last used the ports 2 nights ago and didn't have any problem then. I thought the problem may have been caused by the Windows updates I installed today so I uninstalled them all, but the USB controller still doesn't work.
System Info:
Gigabyte GA990FXA-UD3 motherboard
AMD FX-8350 CPU
16GB RAM
GeForce GTX 770 GPUs
Windows 8.1 Pro 64-bit OS
View 7 Replies
View Related
Jul 1, 2013
To me, this is a huge oversight on Microsoft's part. Imagine being able to boot up your PC, go to Metro, then fire up Steam big picture mode and play your games without ever needing to touch your mouse and keyboard (except, of course, if you are playing an FPS or RTS :3 )
I don't get why this is not supported. It is just such a massive oversight. When I hit the Xbox logo on my controller I would want my PC to switch to Metro mode and allow the navigation of my PC using the thumbsticks, D-pad and face buttons.
Microsoft are trying to be very universal about their devices. Xbox, Zune, Windows, they are trying to get everything into one interface and one brand, so why is the Xbox Controller not supported with Windows for navigational purposes?
View 2 Replies
View Related
May 3, 2013
I have tried everything that I know how to do to find this with no success. I have a dell precision m4600.
View 3 Replies
View Related
Jan 1, 2013
I'am trying 8 hours now to install Windows 8 to an Acer Aspire 5920g.
Problem is that when the usb flash drive comes to hdd presenation point the hdd isnt being displayed.
My guess is that Sata AHCI/IDE controller driver for the 5920g's chipset is missing from Windows 8 installation dvd.
I googled very much and i can only find XP and Vista Sata Drivers while oi need 8's.
Is there an alternative? I must get 8 installed in that laptop.
View 9 Replies
View Related
Mar 19, 2014
With the following problem regarding media streaming in windows 8. Up until recently I could stream video films from my HP laptop & HP desktop onto the TV via DNLA.
After following several posts on various sites it seems that when I try to start the windows media player network in the services I get the error message "windows could not start the windows media player network sharing service on the local computer.
Error 1068. The dependency group failed to start."
In the dependencies tab in the lower box of the two "the following system components depend on this service"
The box is greyed out and the words no dependencies is displayed.
View 3 Replies
View Related
May 11, 2013
I just reinstalled my PC, obviously with windows 8. And I can't seem to play games, i mostly play COD4 and whenever I join a game, I get an Dirextx error, or my PC just reboots..
I don't know if it has something to do with my LPC INTERFACE controller.
LPC One:
on Intel(R) ICH8/ICH8R Family LPC Interface Controller - 2810
The drivers for this device are not installed. (Code 28)
To find a driver for this device, click Update Driver.
Games one:
directx unrecoverable error
And I used to get 'AMD Driver timed out, and succesfully rebooted" something like that.
This is my setup:
OS: Windows 8
MOBO: FOXXCONN p9657aa-8ks2h
CPU: Intel Core2Quad Q6600
RAM: 2GB ddr2
GPU: Club3D Radeon HD 6970 Coolstream Edition
HDD: dont know really, 300gb
View 1 Replies
View Related
Feb 14, 2014
After deciding to give windows 8 another shot and installing windows 8.1 i still stumbled upon the same issue i had before. sound - YouTube In first part of the clip you can hear sound in windows 7 and in second how it sounds in windows 8. While windows 7 sounds perfect, windows 8 has this kind of "in fishtank" sound, not sure how to describe it and also really heavy and loud bass.
Both windows are using the same realtek hd audio drivers. I guess there is something that needs to be either disabled or changed in windows 8, but im not sure where to look for it anymore.
I have been messing around with realtek control panel but no luck so far. Since everything driver related were the same on both windows it's something inside windows 8 that does this.
Windows 8.1 pro / Realtek R273.
Also using usb sound card for headset and realtek for my mic, i can use realtek for both but the issue is still there.
View 2 Replies
View Related
Dec 29, 2013
I'm having a little problem with my onboard audio, having just installed Windows 8.1 (clean install). I have an Asus P8Z77-V LE PLUS motherboard, which includes a "Realtek - ALC889 8-Channel High Definition Audio CODEC" onboard.
I have installed the latest realtek drivers; R2.73 from the official website.
Now, here's my problem: when I was using Windows 7 on this same machine, I could plug headphones in the front panel connector, as well as speakers in the green back panel connector. This would give me two audio outputs in the device manager/sound list, which was pretty practical and enabled me to output different applications through the speakers or the headphones.
Now, however, there's only one output, irrelevant of whether or not I have two outputs plugged in at the same time. They appear in the device manager as a single device called "speakers" (see picture). Instead of both having separate outputs, they both output exactly the same audio.
View 7 Replies
View Related
Jun 23, 2014
I downloaded the most recent version of the realtek drivers from toshiba site and i have no sound when plugging in headphones.
View 6 Replies
View Related
Jul 21, 2013
I have no sound from internet explorer nor do I find a realtek audio driver but how do I know what to download
View 1 Replies
View Related
May 3, 2014
I bought a Gateway E56R41u to replace my Acer netbook. However, I downloaded the free upgrade to Windows 8.1 and my audio quit working. I've downloaded all the drivers that I could find and nothing works. Is there a driver for another machine that will work with my Gateway?
View 1 Replies
View Related
May 28, 2013
So i am going to Reset my PC cause of different issues, and i want to export my Presets i made in Realtek HD Audio Manager, the one you make in the Equalizer and then save. I want to know, where are these save, so i can take them over to a USB drive and after the PC is reseted, i only put them back there, and load them into the Audio Manager.
As example: C:UsersUserAppDataRoamingRealtekEQpreset1.cfg
View 1 Replies
View Related
Apr 21, 2013
My audio disappeared and stopped working. my audio icon has a red x on it and when i click it it wants to detect problems (it doesn't work).
what should i do? how should I diagnose the audio? I feel like this is hardware problem as it just happened out of the blue. The audio board has a USB connection (which is working) so the connection from it to the mother board is fine.
Installing and updating the driver did nothing. I can't get the device manager to detect the hardware (scanning does nothing).
View 9 Replies
View Related
