Computer Fail To Wake Up Correctly After Hibernation?
Nov 28, 2011
Here's my problem:I have a netbook (HP mini 311) that came with Windows XP, and then I've installed windows 7 on it.When the computer goes to hibernation either because the battery is getting too low or that I close the lid (as I choosed these in the power options) , the computer won't successfully boot up to the "Resuming windows" screen. And what I should do is to turn it on and off 3 times, and so it starts normally (to resume windMore notes: at first boot screen (where the hp logo is) , at the bottom right of it, there's usually a "Press esc for startup options" text, that doesn't appear by the 3 first boot ups tries.
View 2 Replies
ADVERTISEMENT
Mar 26, 2011
Is it possible to wake my computer from hibernation to stream content to, lets say, an Xbox 360? Then after its done streaming put the computer back to sleep?
View 3 Replies
View Related
Mar 11, 2011
I want to say 2 days ago, my computer has decided to fail when going to sleep. It is Windows 7, completely updated with no problems to that point. When it falls asleep and I wake it up, the machine starts up and is active, but my monitors and external hard drive are never turned on as they once were and the machine just sits there running with a black screen. I restart, boot back into Windows and it says resume (as if it was in hibernation, but I have hybrid sleep on) and I just get a flashing underscore and no more. I restart once again, it says Windows could not restore the session, I start a new session and all is good again... until the computer falls asleep and the process starts over.
I have tried turning off hybrid sleep. No good. I have tried using hibernation instead of sleep. Same error. I found online where someone said they had this problem with an ATI card, but once the upgraded the Catalyst Control Center and drivers, they had no problems. That did no good. The only update I've done recenly is Firefox, but I have not seen any other reports of the newest Firefox causing sleep problems. I read where someone had a problem with waking up from sleep mode because of Firefox's memory leaks and they said closing Firefox before putting it to sleep helped.It does not matter if I put it to sleep and wake it up immediately or if it goes to sleep and when I get home from work, boot it up. The same thing happens no matter the length of time.I have a dual boot with Ubuntu, but that has been on there for months with no errors and Ubuntu will sleep and wake up just fine. There have been no hardware changes or any hardware driver changes other than the video card. I tried rolling back video card drivers to see if there was a difference with no change. My ASRock MB has the most up to date BIOS that has been out for over a year. My video card is a 5770, but like I said, I've tried older and new drivers. I tried the prevx black screen fix with no luck.
View 9 Replies
View Related
May 23, 2011
Earlier today, my laptop wouldn't wake up from hibernation, so i restarted it. I got it started and it said there was a windows error and suggested i boot up as normal. I did that and it was all running fine. But the sound wasn't working! The issue of sound not working has happened before so i just restarted the computer (because that has fixed the problem in the past). It started the boot up as normal and almost made it to the log in screen, but wouldn't pass the black screen before the log in. I thought that was very odd so i restarted it after waiting about ten minutes of nothing happening. It then started up with the suggestion to run the start up repair program. I highlighted that and hit enter. it started up, went to a black screen, then after about 3 or 4 minutes, loaded what looked like a blueish wallpaper. it didn't do anything after that for about 15 minutes, then it loaded the repair program. I ran that for 40 minutes but it didn't appear to do anything so i hit cancel. It then gave me the option to do a system restore, which i did. I restored my system to about 2 weeks ago, seeing as i didn't have any problems 2 weeks ago. It restarted and booted up, this time staying on the black screen for about 3 minutes, then going to the log in. It logged in perfectly fine, but there's still no sound. I tried opening the troubleshooter, but it won't open. For some reason, Google chrome works fine, and task manager does too, but some programs won't open. It's like, they try to open, and the task manager says they're running, but they won't appear on screen. Programs like, Steam client, iTunes, System recovery. Those were three different ones that i tried and didn't work. It appears to be quite random. I tried running Boost speed to see if it could diagnose a problem, but it said that it couldn't connect to the drives. I ran my antivirus software to see if it was a virus causing the problem, but it came up with the same error! I really am at a loss for what's going on! This laptop is only 5 or 6 months old. The drives shouldn't be failing already. [code]
View 2 Replies
View Related
Feb 11, 2013
I'm not sure if this is the right place to post this..but..my laptop HP ProBook 4540s..i just bought it...i make it to go to stanby mode..but when i press the ON button..from the lights I see the laptop is ON..i hear windows sounds..but I don't see any picture..if I'm not mistaken it happens with both standby and hibernation modes
View 5 Replies
View Related
Apr 20, 2011
I live in a place where we have power shortages from time to time. I have my Dell desktop pc attached to a UPS and i have configured the pc to go to sleep after 5 minutes when on UPS. Is there anyway to wake up the pc automatically once the power is on? I have connected my UPS with USB cable to the pc, and the pc treats the UPS as a battery. I use this pc as a media centre so this feature is something i really need.
View 4 Replies
View Related
May 2, 2012
I've got it to work flawlessly on my desktop, however on my laptop, a Dell D630, I can't seem to get it to work. I've created a task triggering on a specific time and running the operation '/c "exit"', which should just start a command prompt and close it again. I've set it to "run with highest privileges" and "wake the computer to run this task". However, it just doesn't boot as scheduled.
The history of the scheduler says nothing at the moment that the trigger is set to go off, but a minut later (probably when I manually boot) I get a "Task scheduler "{....}" instance of the task "Wakeup" due to a time trigger condition."
View 3 Replies
View Related
Dec 8, 2012
When I put my computer in hibernation, sometimes when I wake it, it hangs at the user select screen, or it just shows a black screen. Sometimes I can reset the computer after it has hanged, and try again resuming from hibernation, and many times it will work after a couple of tries. Other times after resetting I won't get the prompt to try again with resuming (the other option is to delete hibernation data and reboot the system) but I will get the usual screen that says that Windows was not shut down correctly (with all the options for safe mode, etc). If I cannot resume and I get the screen with safe mode and all the other crap, I finally log in I get a notice that there was a critical error, in the details I see BlueScreen and other data, but I actually never get a blue screen. In the dump folder, there are no dmp files related to the hibernation hanging.
Anyway, when it happens, I see several Event 18 WHEA-Logger in the event viewer, about 6 of them every time.What's weird though, is that I literally have NO problems with this computer other than this. The only times it hangs is when I resume it from hibernation. I can play games or run stress tests with or without overclock and the system is 100% stable. But there is some problem that prevents it from resuming from hibernation correctly, so every time I use it is basically a gamble because it has like 50% chance of working.I tried EVERY SINGLE solution I found with google related to hibernation problems, and it's still there. I even formatted and reinstalled Windows from scratch, and it's still there. I'm positive I updated every single driver for every hardware I have and nope, no solution.I know the WHEA error is related to the hardware but like I said, everything works PERFECTLY once the system starts up properly, or when it resumes from hibernation properly. [code]
View 6 Replies
View Related
May 28, 2011
My computer wakes from hibernation.I�m using windows 7 x64. My BIOS doesn�t support any configuration settings about wake, and the LAN device driver states that it doesn�t support wake on LAN.It�s a Dell Lattitude laptop, about 2 years old.No events are relevant.This started about 6 months ago when I went out and updated all my drivers, so some driver is apparently having fun. I had already run for long enough when it started that I didn�t want to roll back, although I have tried earlier versions of the LAN, WAN and WLAN drivers. None of them have an option for disabling wake on LAN that can be checked.
C:>powercfg -lastwake
Wake History Count - 1
Wake History [0]
Wake Source Count � 0
C:>powercfg -devicequery wake_armed
gives no output.
View 4 Replies
View Related
Dec 4, 2012
My new HP desktop is in hibernation mode and the monitor displays a message that says it can't come out of hibernation. What can I do?
View 3 Replies
View Related
Dec 21, 2012
I just bought a NIB (New In Box) Windows 7 computer and I have run into a problem I have not seen and don't know what to do with. I keep my computer password protected due to financial and other sensitive information I have on it. Whenever I am away for an extended period I lock my computer using the Windows Key - L combination.If I am only away for short periods of time everything is fine but if I am away from my computer for an extended period and I try to wake my computer up it won't come out of hibernation and I have to use the power switch to shut it down and restart it and of course I get the "Windows did not shut down normally" screen.I like to leave my computer on for convenience and to get Windows updates but I now hesitate to do this if I am going to have to deal with it not coming out of hibernation every time I am away for a long period. I suppose I could always leave it on but this uses a lot of power as well as wear and tear on moving parts.
View 2 Replies
View Related
Oct 25, 2011
I recently built a new rig and I had a problem with one stick of memory. The other stick worked alright, but I've been getting random failures. Can bad memory be inconsistent? Right now, I can't start my OS up at all. It goes straight to the Windows Repair Launcher, which fails. When it gets there, I can either find a restore point or let it 'attempt to fix' for as long as I can endure. The restore point option results in 'instruction xxx failed. memory reference xxx failed.'This leads me to believe there is a problem with the memory. But, could it be the motherboard? I played a video game for hours last night, as well as surfed the web and ran other applications. Everything was fine, until I shut down. This isn't the first time this happened. Last time, I 'fixed' it by switching the 'good' memory stick with the bad. The bad resulted in getting the OS up, but lots of BSOD's
View 7 Replies
View Related
Sep 16, 2012
Since early August all my Security updates have been failing. It adds time to each boot up period as it goes through the updates and then at the end will say it's failed and is reverting all the changes. I have already done some research on this issue and ran "sfc/scannow" as well as "chkdsk/f/r." Both seemed to go through with no problems. After that I did a Windows update and 12 updates seemed to go through with no problem until the required reboot where we're back to the same issue of failing and reverting.
View 9 Replies
View Related
Jun 9, 2012
I have a one year old Lenovo Thinkpad Edge E420s. I'm using Windows 7 Ultimate x64 with an Intel i5-2410M @2.30GHz. I bought the Ultimate OS retail as an upgrade to the Windows 7 Home edition. Recently, when I put my computer in hibernate or standby, when I turn the computer back on, it causes the BSOD and the computer restarts.I have attached the dump files.Here is the error message I get when the computer finally starts:Windows has recovered from an unexpected shutdown
Problem signature:
Problem Event Name:BlueScreen
OS Version:6.1.7601.2.1.0.256.1
Locale ID:1033
[code]....
View 4 Replies
View Related
Nov 28, 2012
Recently, my computer will not wake up from sleep mode. Once it enters sleep mode, the only way to get it functioning again is to hold the power button, completely shut it off, and then boot my system back up. It appears as if everything starts back up once I open the lid or press the power button to wake it up, but the screen never turns back on. The fan starts up, the backlit keyboard lights up, the leds all blink, but nothing I try will turn the screen back on forcing me to press and hold the power button for a complete shut down.I have reinstalled the latest Intel HD Graphics driver as well as the latest NVIDIA graphics driver (both the stable and beta release).I do not get a blue screen or any sort of error. Upon the restart, I am not prompted with any error from windows or any signs of the forced shut down.
View 1 Replies
View Related
Jun 1, 2012
I have heard of WOL. If I am located at a different location then my computer (different subnet,network) then how can I wake my computer up ?
View 1 Replies
View Related
Oct 27, 2010
my computer sometimes wont resume from sleep when i hit a button on the keyboard, if i do it fires up then just dies out completely. its like someone hit the power switch on the p.supply. it just does this randomely, not all the time but its extremely annoying because i have to boot from scratch everytime. my specs are gigabyte ma790xt-ud4p, Amd x4 955 phenom 2 G-skill ripjaws 4gb ddr3(2x2gb) Seasonic 700w P.S CM v8 cooler and so on.im running windows 7 Ultimate 64
View 1 Replies
View Related
Mar 8, 2012
Computer has been working perfectly and decided to try the sleep mode last evening as opposed to turning it off. Bad move, now the keyboard, mouse and monitor are unresponsive. No way to communicate with the computer whatsoever. Tried re-booting but can tell from the sound of it, is only powering back on in sleep mode.
View 2 Replies
View Related
Apr 18, 2011
On a brand new, freshly installed Windows 7 Ultimate 64. I get the following error when resuming from Hibernate: "Your computer can't come out of hibernation. Status 0xc000009a". No other info, no reference to any file such as hyberfil.sys. I have tried to "powercfg -h on/off", reboot defrag and reactivate hibernation, however the problem is still there.....what can I try?
View 9 Replies
View Related
Dec 30, 2011
First and foremost, details of my lappy:Asus A43SWIndows 7 64 bitAMD Radeon HD 673Intel core i7 8gb RAMIt is a new lap, just bought 2 mths ago.Noticed the first problem with it is 1) THe computer becomes slow and cranky and even crashes after resuming from the hibernation or sleeping (fall short of a BSOD, eg can't move mouse, etc...and have to hard restart the laptop). Managed to reduce the frequency of i from always to infrequent by setting the hard disk turn off, sleep and hibernate option in the power option to never. Lots of forum explained such similar problem, but despite updating BIOS, display driver, asus ATK utility driver, etc...still persists2) Now coming to the 2nd question which I am wondering is it related to the problems after resuming from sleep/hibernate.
Got repeated BSOD today.....after I update the power4gear hybrid utility (by asus to a newer version) version 1143 to 1150. Managed to generate and use debuggin tool to see the dump file...which shows ntoskrnl.exe as possible cause. MInd you that this also the same culprit that appears in the dump file in my problem number 1(which has once BSOD during resuming from hibernate/sleep)So is number 1 and number 2 related?What is wrong actually with number 1 problem?What is ntoskrnl.exe, and how to fix it?
View 3 Replies
View Related
Dec 16, 2011
Every time I manually start hibernation it will begin the process; the monitor will go blank, the harddrive starts making the image and after about 30 seconds the the monitor comes on and the computer is in normal operation. I have tried enabling it with the command line (powercfg -h on) as the administrator with no success. This just started yesterday. I have not installed any new applications or any new updates.
View 1 Replies
View Related
Feb 18, 2011
I have a perplexing situation with my three-year-old Toshiba laptop. If I resume working after allowing the computer to hibernate, a bit after that (maybe 10 minutes) the screen goes blank--no mouse--no background. Hitting Ctrl+Alt+Delete does not bring up the Task Manager. Nothing I do seems to work except physically shutting the on/off switch, waiting a bit, and rebooting. I get a message upon reboot that the machine was not shut down properly. The machine has an AMD 64 X2 Athlon processor 1.7Gb. I have 2 GB of RAM installed and Windows 7 Home premium.The drivers seem to be all up to date. I have an active antivirus/firewall running.What would cause such a problem? Any suggestions in solving the issue? This is driving me nuts. If I don't allow the computer to hibernateHere are some member answers to get you started, butplease read all the advice and suggestions that ourmembers have contributed to this question
View 29 Replies
View Related
Nov 11, 2012
I built this computer in March of this year and everything worked great. I had my power options set up so I could switch between high performance and power saver for when I'm not using it. Power saver was set up to turn off display and put the computer to sleep after 1 minute. I don't recall changing any of the advanced settings but maybe I forgot something.
I used to wake it up simply by hitting the space bar and everything would come back on. I just did a clean install of Windows 7 two days ago and since then when I choose power saver and it goes to sleep after whatever time I set it to, it no longer wakes up. Well, this is where I'm lost because it still makes the same noises like the fans spinning harder and all that but nothing appears on my monitor. At first I thought it had something to do with my monitor but I just realized that the lights on my mouse don't come on either. Which they used to before when I'd hit the space bar.
My build:
Windows 7 Home Premium
Processor: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz
(RAM) 8.00GB
System type: 64- bit
View 9 Replies
View Related
Dec 5, 2011
I'm trying to use WIN7 task scheduler to wake the computer and run a program. I have checked "Wake computer to run task", but the task doesn't run until I manually wake the computer---then it runs correctly. Are there any other setting I need to adjust to allow task schedule to wake the computer
View 3 Replies
View Related
Mar 30, 2012
Should I tweak anything? I just tried "powercfg -energy" today and it shows about 15 warnings in my Energy Report. The reason I did this is because my computer does not wake up from sleep mode sometimes.
View 3 Replies
View Related
Jan 23, 2012
I have an inspiron 1545 running windows 7 (x64) and I am having problems waking up my computer from sleep . Usually, when I put my computer to sleep, I have problems waking up my computer. The screen stays relatively dark when I move my mouse although I can see some light coming from the bottom part of the screen (so the screen seems to be on, just not showing anything sueful). When I try to press the space bar multiple times, my computer gives me a warning ding and it plays a sound when I insert or remove my usb mouse.
View 1 Replies
View Related
Dec 6, 2011
My computer is several years old, and just a few weeks ago started having a problem waking from standby. Up until now, it had no issues going into and coming out of sleep.Now, whenever it goes to sleep (whether due to inactivity or putting it to sleep manually), it won't wake up. The lights come on, the fans come on, but the monitor stays in standby. I've looked around online and found that many people get a black screen when booting up, i.e. the monitor comes alive and they may get a mouse cursor, but that's not what's happening to me. I don't get a black screen--my screen is never getting a signal from the computer. I have to do a hard reset, after which I get the 'Start Windows Normally' screen.I've tried uninstalling and reinstalling the graphics drivers, changing hybrid sleep settings, using hibernate instead of standby, uninstalling random programs, etc, to no effect. I don't think I had any major windows or driver updates that caused it.
View 1 Replies
View Related
Aug 26, 2011
It does this every once in a while. It happened twice in the past 2 days. I'm not sure if it's something I left open before going into sleep mode or something else.So the computer's been in sleep mode, usually for at least an hour. I do the usual thing to wake it up, move the mouse. After a simple movement fails, I try again, moving vigorously and clicking all the mouse buttons. I have also tried pressing all the keys on my keyboard.
View 3 Replies
View Related
Sep 17, 2012
my mouse and keyboard are frozen. I've rebooted. I get the message that 'the system closed down unexpectedly and a choice for starting in the safe mode, etc., comes up yet the keyboard and mouse still do no work
View 11 Replies
View Related
Nov 24, 2011
So when I came back from class today, my computer was off and so I turned it on. It never got passed what seems to be the BIOS screen (I don't actually know what it is, but that's what I think it is).
I have a Predator G Series G5900, with no modifications. Attached is the photo of the screen I have when I turn on the computer.
What I have tried:
- Unplug every USB device and take off the power supply. Hold the power button for 30 seconds. Reboot.
View 2 Replies
View Related
Jul 17, 2012
trying to format my computer,but each time i try to put windows 7 on my dell inspiron 350.i must have about 3 different windows7 on my computer now and its slowing it down.what can i do to make it run faster.
View 3 Replies
View Related