Access A Cable Modem Via Wireless Access Point?
Feb 19, 2012
This question may not be what you think it is. I am trying to fix an intermittent issue in my home environment. The issue is I am having to use wireless. Our Xfinity Cable/WAP modem sits on the top floor of our house. I am located in the basement. The wireless signal I get most of the time is very good, and by very good i mean at least 15+ mb/s on [URL]
I am taking the Cisco Network Academy classes and am familiar with network terminology and concepts. However, what I'm trying to do is take a router/WAP (using it downstairs where I'm located) and configure it to access our xfinity modem upstairs, so that I can plug in to it downstairs using a RJ-45.
Let me know what yall think. By the way the router/wap i would be using is a netgear model unknown at this moment but could easily find out.
View 4 Replies
ADVERTISEMENT
Jan 23, 2012
In a few days time I will be changing my ISP in the UK from Sky to BT.
BT are providing me with their newest wireless router free of charge as part of the deal and I'll be using that to set up my wireless network, which will consist of an HP Pavilion desktop, a Toshiba laptop, a Sony Vaio laptop, an HP wireless printer and a Samsung HDTV.
This means my Sky wireless router is surplus to requirements, so I was wondering if I could convert it to a wireless access point to improve the range of my BT wireless network.
I've read a couple of supposedly easy-to-understand articles on Google and have to say they left me more confused than ever.
View 6 Replies
View Related
May 26, 2011
I live in the UK and use Sky as my ISP.The wireless router they supply is OK as far as the internet side of things is concerned, but for a good wireless connection to my wife's laptop in the next room, it sucks.I have a spare Netgear DG834N Wireless ADSL2 modem router and was going to use this instead of my Sky router in an effort to improve the wireless range. Unfortunately, Sky's T's & C's insist that using a different router to the one they supplied could result in my internet service being withdrawn.In an effort to prevent people using a third-party router, Sky have encrypted theirs with a username and password (not the username and password used to logon for e-mail etc) that can be retrieved with a hack, but I prefer not to go down that route.What I would like to do is use the Sky router to handle the internet side of things, and then use my Netgear router as a wireless access point to give us better wireless coverage around the house.Is this possible and if so, how do I go about it?
View 8 Replies
View Related
May 26, 2011
I currently have the following network configuration:- Broadband Cable Modem (in my den) - Router (in my den) - Computer (in my den) - Wireless Access Point (family room)My broadband cable modem is connected to my router via ethernet cable. I also have an Ethernet cable running from the back of my router directly into my PC. My current setup is in my den (I will explain). In my family room (which is away from the den) I have my television and several other wireless devices (Roku box, etc). My signal strength is low in my family room due to many walls between my den and family room. I therefore installed a Wireless Access Point in my family room by running an Ethernet cable into my basement and connecting the router in the den to the Wireless Access Point in my family room. Now here is my question: I set the SSID (or network name) of the Access Point so that it is the same as my current network name (that way I see the AP on the network). Now here is where I need to understand how a wireless Access Point works. If I have a laptop or other wireless device in my family room and search for a wireless signal, am I connecting to my router (that has a weaker wireless signal than the AP) or to my Access Point (stronger because my Access Point is a foot away from my wireless devices) since they both have the same network name? And if I connect at that strong signal and walk into another room where the signal is weaker, does my laptop automatically connect to the wireless router? How do I tell if both my router an wireless Access Point are using the same SSID or network name. I guess what I'm trying to ask is where am I getting my wireless signal from, the Access Point or the Router or both (assume I am in wireless mode).
View 4 Replies
View Related
May 18, 2012
I am using Windows 7 and Netgear router and trying to set up the wireless network and keep on receiving the message - problem with wireless adpator
Is this a known problem with Netgear WGT624 router?
View 1 Replies
View Related
Oct 1, 2012
I cannot access the web either by cable or wireless. I tried to uninstall all of my network devices software but the WAN would not uninstall and would not update.
View 1 Replies
View Related
Oct 22, 2011
can't connect to internet it says connection between access point router or cable modem and internet is broken
View 4 Replies
View Related
Nov 20, 2011
Just ordered the following router: TP-Link TL-WA901ND Advanced Wireless N Access Point: Amazon.co.uk: Computers & Accessories I have a garden shed 30 metres away so hopefully 802.11n should be able to reach. The aim is to use 802.11n so speed is better in my house and my shed. However I heard that 802.11g dongles and computers limit the network speed if you connect them to a router running 802.11n. (Can you do this?)So I might try running 802.11n on the new router (in the main house) and running an ethernet cable down from the new router to the shed where I will have my old Belkin (g) router running 802.11g (as a new access point, if you can do this- if not what are my options)On Amazon, this is the cheapest wire I could find but its not external so will it get damaged quickly if I have it exposed (will burying it underground make a difference?): High Quality 40M CAT5e RJ45 Ethernet Network Fast LAN: Amazon.co.uk: Electronics
View 5 Replies
View Related
Feb 5, 2011
I'll try to be detailed on this. I've worked on it and read on it for almost 7 hours and I'm stuck. I'm using a Win 7 Pro desktop that is hardwired and a Win 7 Home Premium laptop wireless. Both current on all updates.My Comcast modem is hooked into a WRT160N that is hardwired to a WRT400N which is being used as an access point, and to the desktop PC. Both routers have the latest firmware. Both routers have the same SSID and password but use different channels. (2 & 6) Internet works perfect both wired and wireless through both routers.The homegroup has been set up through the desktop but I've removed and added homegroups on both machines multiple times. My problem doesn't go away. The homegroup works when the laptop is either wired or wireless using the WRT160N. It will not work at all through the WRT400N. I can be in the room with the WRT160N on the homegroup, when I move to the other router so the wireless switches to the WRT400N, it drops the homegroup. The internet stays connected just fine. Once it drops the homegroup, it can't find it until I go back to the main router.Both machines have IPv6 addresses, auto discovery is on.
View 1 Replies
View Related
Aug 4, 2012
my son always keep looking Internet videos though my wireless modem. so is there any way to block modem for other devices. so that only i can access.
View 2 Replies
View Related
Sep 15, 2012
I am currently using internet on DSL on Local Area Connection. It is not a dial up connection. I also have a WiFi access point. Now, I want my all the applicatons like browsers, Yahoo, Live Messenger etc. to use internet through LAN as usual but there is this application for which I want to use internet for through WiFi, not LAN. Just like Proxy Firewall, you choose for different applications the different proxies. Like this, I want different connections for different applications.
View 3 Replies
View Related
Dec 25, 2011
how to access the secure WEB encryption wifi accesspoint?
View 2 Replies
View Related
Nov 25, 2011
In order to change my password a service provider had to reset my modem.I can go on the internet with my desktop, but I am having difficulties going on the internet with my laptop. It seems that my wireless router has to be reset also but he can't do it because it's not one of theirs. He did explain to me though that I have to put the I.P. address into the browser in order to get on the router's brand name and so on, which I did but I don't know what to do next. My router's I.P. address is 192.168.0.1 It is a NEXXT Nebula 150?
View 3 Replies
View Related
Nov 12, 2012
I am trying to configure a Netgear WNR3500 router to be used as an access point.My AT&T U-Verse Gateway router is in the basement of my house and the WNR3500 is in my office on the second floor of my house. I am using the Netgear Knowledge Base article ID 19852 titled "Set Up a Wireless Router as an Access Point on a Network".In Step 5 is says in Advanced tab Setup > LAN "In the IP Address field, change the LAN IP address of the router (WNR3500) to 192.168.1.100 (same IP segment of the main (AT&T) router (192.168.1.1) and uncheck the DHCP server box.I did that and the wireless access point doesn't work.The AT&T Gateway wireless router IP address is 192.168.1.254. I also tried changing the WNR3500 LAN IP address to 192.168.1.200 and the access point still doesn't work.
View 5 Replies
View Related
Apr 15, 2012
I have a problem with connecting to my modem. When I plug it in to computer I've got "Unidentified network" and no network access, when troubleshoot: "Local Area Connection doesn't have valid ip configuration", then when ipconfig /all: there is no default dns, and when trying to /renew cant do anything cause "media disconnected". Modem type is Netopia 3341-ENT...
View 9 Replies
View Related
Nov 23, 2012
i am pradhap, i am using a mobile that contains wifi. it performs wifi wireless n/w and a modem. so how to access wifi connection form my mobile to windows7
View 1 Replies
View Related
May 11, 2012
I am having a hard time configuring my Access point. I have a DSL Router connected to our telephone line and it works fine wirelessly, Yesterday I purchased TP LINK Router to configure as Access Point to extend wireless signal up to the second floor. Now, I am wondering, should I do some re-configuration on my DSL Router before configuring my TP Link Router? Guys, Please share your thoughts and if you have knowledge on how to configure my 2nd Router to my WifiNOTE: I followed the user guide manual that came with my TP LINK router but it is no USE. I just need to know if should I reconfigure my 1st Router in order to communicate with my 2nd Router.
View 4 Replies
View Related
Apr 3, 2012
internet connecting thru modem but unable to access web page dns - error, I have a Internet connection by the Lan provider, If I connect thru his connection it works but If I connect thru Data Card - In network section I find that there is no "internet connection". But the modem showing the connection. If I try to open any webpage it gives DNS error or web page not reachabl
View 2 Replies
View Related
Jul 19, 2012
I'm a 3g dongle to connect to the net, I previously set up the ps3 to connect through same via the wired connection. That work fine for a bit, until I updated the firmware, Since then the PS can't seem to obtain an IP address and after setting a static IP it gives me a DNS error. On the flip side, my LAN is giving me a no internet access problem(ipv4) and also an unidentified network
I've changed the cable, released and renewed and reset the ipconfig and also flush DNS. I'm having the same problem with my laptop. Both were able to share the connection with the PS3 before.
(Pc runs windows 7 32 bit and laptop win 7 64bit)
View 2 Replies
View Related
Jul 19, 2012
My laptop suddenly stopped being able to connect to the network in my house and for that obviously it doesn't have any internet. It doesn't work either by connecting a cable or trying to use the wireless, here are the detaills for each case: When I connect the cable, the laptop detects it, but doesn't detect any network, it doesn't seem to even be trying. I checked on the network adapters, and it clearly says "enabled" when connected and when disconnected it changes to "No network cable plugged in". When I try to connect to my network, it always ends up saying "Limited access", when I tried troubleshooting, it said that there may be an error with the network drivers, I tried the fix there, and then it says that there must be an error with the network adapters.
Here's what I have tried so far:
-Reinstalling the devices and drivers, when I check them in device manager, it says that both the wireless and network driver are working properly.
-I tried resetting the router.
-Tried resetting the bios of the computer to it's factory ones.
- Tried resetting IPv4 and IPV6, along with the IP/TCP using the command prompt, still no go.
When I try to ipconfig /release or ipconfig /renew, I get an error saying the next thing: "An error ocurred while releasing interface Loopback Pseudo-Interface 1: they System cannot find the file specified. The operation failed as no adapter is in the state permissible for this operation."
Here is my info when using ipconfig /all:
Host name... : Jorge -NB
Primary Dns Suffix : Empty
Node Type : Hybrid
IP Routing Enabled: No
Wins Proxy Enabled: No
Tunnel adapter teredo tunneling pseudo-interface:
Media state: Media disconnected
Connection-specific DNS suffix: empty
Description: Teredo Tunneling Pseudo-interface
Physical Adress: 00-00-00-00-00-00-00-E0
DHCP Enabled: No
Autoconfiguration enabled: Yes
View 2 Replies
View Related
Mar 24, 2012
I have internet sharing on my mac turned on, so trying to get the PC to read the laptop as an access point via said cable. I know this has been done on XP, but I'm having issues with Windows.
View 1 Replies
View Related
Nov 11, 2010
For some reason my router and modem will not show correctly on my dell inspirion one desktop. Im running windows 7 and here are the net work connection deatils
Connection -specific DNS Belkin
Description Realtek PCIe GBE Family Controller
Physical Address 00-00-00-00-00-00
DCHP Enabled Yes
Ipv4 Address 192.168.2.2
Ipv4 Subnet Mask 255.255.255.0
Lease obtained Wednesday, November 10, 2010 9:45 PM
Lease Expires Sunday, December 18, 2146 4:17 AM
IPv4 Default Gateway 192.168.2.1
Ipv4 DHCP Server 192.168.2.1
Ipv4 DNS Server 192.168.2.1
IPv4 WINS Server
NetBIOS over Tcpip enabled Yes
The Connection was working about ten days ago and then suddenly stopped and read as an unidentified network no internet access. at one point is was not receiving packets but now it is but it still says no internet access on the IPv4 Connectivity. Media state is also enabled and the speed is 100.0 Mbps when i troubleshoot it says windows cant identify problem but in the details it says default gateway is available. when i use the cmd prompt ipconfig/all my local ethernet adapter has a physical address of all zeros.
View 9 Replies
View Related
Apr 28, 2012
I wouldn't go so far to say, I'm totally computer illiterate, but not far from it.. If there's anyone out there, who's up for a challenge I'm running windows 7. I am the administrator. Someone I don't trust at all, used my PC a while back. After he (did whatever he did) I noticed I couldn't access several files. I get a "access denied" or you don't have permission to view this file, owner info etc.. I can see a lot of the files, but their either empty now or I can't view them. I have used restore many times in the past, but now I get a message " no restore points".. I don't know what he did, or if he did anything.. It could be one of my kids changed properties by mistake, before I wised up and created a basic user acct w/ limited access for them.. I almost forgot. When I go into file properties there is a red x by my user name (administrator) Not in every property, but several.. Sometimes there is a red x by other user names, as well, but mostly mine.
View 3 Replies
View Related
Jul 7, 2012
My internet connection shows 'no internet access' even though my ISP shows the connection is coming into the house just fine. I usually use a router (NetGear-WNR3500U) but I right now I have the Ethernet connection plugged directly into my PC. I tried directly plugging into my laptop and the internet works just fine. So I know the problem resides in the PC.
Some troubleshooting things I have tried.
-Power cycled my modem, router and PC.
-Repinged my connection from my ISP(Comcast Xfinity)
-Used the reset option on the router and the modem
-I was walked through the internet options needed with the tech support from my ISP to make sure DHCP was enabled and every other setting was correct, and he cleared me that all settings were correct.
-Tried ipconfig commands to /renew and /release my IP When I tried ipconfig /renew I get the error 'An error occurred while renewing interface Local Area Connection : unable to contact your DHCP server'
-Restored my PC to a restore point where the Internet was working
All of these options did not work.
What I think the problem is and I am not sure how to fix it, when I run the ipconfig /all command my Auto configuration IPv4 Address shows 169.254.112.76 which I was told is a router IP address even though I am plugged directly from the modem to my PC with an Ethernet cord. So I think that's my problem? But I am not sure.
View 4 Replies
View Related
Jan 6, 2013
I have a laptop and regular computer and a new modem sent by comcast also a wireless modem. I can only get one to work. what am i doing wrong?
View 3 Replies
View Related
Apr 17, 2011
New computer - Dell Inspiron 15R laptop. Windows-7 home premium 64-bit. Trying to access internet. 7 gives connection option of Broadband where ISP requires ID and Password. However, my ISP does not require this info to log on....its just "plug-n-play" I have run every test and diagnostic that I can find and the only prob I can find is something to do with the DNS, but have no way to fix the problem. The connection is Cable Modem, via LAN wire. One of the diagnostics recognizes my ISP, but still won't let me connect.
View 9 Replies
View Related
Aug 27, 2012
tw-Roadrunner rents cable modem for 3 bucks/month - What device can I buy that will do a good job of this so I don't pay rent forever, if any?
View 6 Replies
View Related
Jun 22, 2010
I've been using wireless internet for months with my new computer which has Windows 7 64-bit. Today I disabled the wireless security for a bit, then tried to enable it, now I can't connect to anything. The problems are: 'The DNS server isn't responding' and 'Local Area Connection doesn't have a valid IP config'. My wireless icon keeps switching between a yellow exclamation point icon and a circular blue loading icon. It says it's connected but I cannot browse the net, I can access my router information though. My router/modem are definitely on and connected. I've done many power cycles on those and my computer. My modem is Comcast and my router is a Netgear WPN824 V2. The router has the most recent firmware.
Here is my ipconfig data:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersVector03>ipconfig
Windows IP Configuration
[code]...
View 3 Replies
View Related
Apr 22, 2012
Already reset tcpip as admin, reset the modem, disabled bonjour, set Internet protocols to auto. Can connect on itouch, other laptops can as well. Only me and my friends laptop can't.
View 3 Replies
View Related
Nov 10, 2009
I rarely need to send/receive a FAX, but I would like to know how before I need to. In the past, I had a dialup FAX modem, but now I'm on cable, and I never thought about FAXing until just now. My printer also has a FAX function, but the only driver available for it on Windows 7 is the one that Windows 7/Windows Update installs.In the Windows FAX/Scan program, the scanner works perfectly, but When I try to creat a new FAX, it says that I need a FAX modem. I have no idea of whether my cable modem is capable of that or not, but when I select to send a FAX, a window appears stating that I need a fax modem or server, but when I select to use a local modem, an error appears saying that I need to contact the administrator (me). From the interface, the only thing that appears to be for setting this up is the Tools>Options menu, but when I click on that, nothing happens.The first question is whether it is typical for a cable modem to be able to handle a FAX or not?
View 9 Replies
View Related
Dec 3, 2012
my pc was causing a lot of problems. i have a verizon wireless jetpack,with a netgear wireless adapter. I tried uninstalling netgear, then wanted to reinstall it. But I cant install it. It keeps saying no connectivity can b found. like there is a connection missing to the modem. A VW tech guuided me through the jetpack, everything was fine with that. What do I need to do?
View 2 Replies
View Related
