Homegroup Through Access Point NA?
Feb 5, 2011
I'll try to be detailed on this. I've worked on it and read on it for almost 7 hours and I'm stuck. I'm using a Win 7 Pro desktop that is hardwired and a Win 7 Home Premium laptop wireless. Both current on all updates.My Comcast modem is hooked into a WRT160N that is hardwired to a WRT400N which is being used as an access point, and to the desktop PC. Both routers have the latest firmware. Both routers have the same SSID and password but use different channels. (2 & 6) Internet works perfect both wired and wireless through both routers.The homegroup has been set up through the desktop but I've removed and added homegroups on both machines multiple times. My problem doesn't go away. The homegroup works when the laptop is either wired or wireless using the WRT160N. It will not work at all through the WRT400N. I can be in the room with the WRT160N on the homegroup, when I move to the other router so the wireless switches to the WRT400N, it drops the homegroup. The internet stays connected just fine. Once it drops the homegroup, it can't find it until I go back to the main router.Both machines have IPv6 addresses, auto discovery is on.
View 1 Replies
ADVERTISEMENT
Feb 19, 2012
This question may not be what you think it is. I am trying to fix an intermittent issue in my home environment. The issue is I am having to use wireless. Our Xfinity Cable/WAP modem sits on the top floor of our house. I am located in the basement. The wireless signal I get most of the time is very good, and by very good i mean at least 15+ mb/s on [URL]
I am taking the Cisco Network Academy classes and am familiar with network terminology and concepts. However, what I'm trying to do is take a router/WAP (using it downstairs where I'm located) and configure it to access our xfinity modem upstairs, so that I can plug in to it downstairs using a RJ-45.
Let me know what yall think. By the way the router/wap i would be using is a netgear model unknown at this moment but could easily find out.
View 4 Replies
View Related
Nov 20, 2011
Just ordered the following router: TP-Link TL-WA901ND Advanced Wireless N Access Point: Amazon.co.uk: Computers & Accessories I have a garden shed 30 metres away so hopefully 802.11n should be able to reach. The aim is to use 802.11n so speed is better in my house and my shed. However I heard that 802.11g dongles and computers limit the network speed if you connect them to a router running 802.11n. (Can you do this?)So I might try running 802.11n on the new router (in the main house) and running an ethernet cable down from the new router to the shed where I will have my old Belkin (g) router running 802.11g (as a new access point, if you can do this- if not what are my options)On Amazon, this is the cheapest wire I could find but its not external so will it get damaged quickly if I have it exposed (will burying it underground make a difference?): High Quality 40M CAT5e RJ45 Ethernet Network Fast LAN: Amazon.co.uk: Electronics
View 5 Replies
View Related
May 26, 2011
I live in the UK and use Sky as my ISP.The wireless router they supply is OK as far as the internet side of things is concerned, but for a good wireless connection to my wife's laptop in the next room, it sucks.I have a spare Netgear DG834N Wireless ADSL2 modem router and was going to use this instead of my Sky router in an effort to improve the wireless range. Unfortunately, Sky's T's & C's insist that using a different router to the one they supplied could result in my internet service being withdrawn.In an effort to prevent people using a third-party router, Sky have encrypted theirs with a username and password (not the username and password used to logon for e-mail etc) that can be retrieved with a hack, but I prefer not to go down that route.What I would like to do is use the Sky router to handle the internet side of things, and then use my Netgear router as a wireless access point to give us better wireless coverage around the house.Is this possible and if so, how do I go about it?
View 8 Replies
View Related
May 26, 2011
I currently have the following network configuration:- Broadband Cable Modem (in my den) - Router (in my den) - Computer (in my den) - Wireless Access Point (family room)My broadband cable modem is connected to my router via ethernet cable. I also have an Ethernet cable running from the back of my router directly into my PC. My current setup is in my den (I will explain). In my family room (which is away from the den) I have my television and several other wireless devices (Roku box, etc). My signal strength is low in my family room due to many walls between my den and family room. I therefore installed a Wireless Access Point in my family room by running an Ethernet cable into my basement and connecting the router in the den to the Wireless Access Point in my family room. Now here is my question: I set the SSID (or network name) of the Access Point so that it is the same as my current network name (that way I see the AP on the network). Now here is where I need to understand how a wireless Access Point works. If I have a laptop or other wireless device in my family room and search for a wireless signal, am I connecting to my router (that has a weaker wireless signal than the AP) or to my Access Point (stronger because my Access Point is a foot away from my wireless devices) since they both have the same network name? And if I connect at that strong signal and walk into another room where the signal is weaker, does my laptop automatically connect to the wireless router? How do I tell if both my router an wireless Access Point are using the same SSID or network name. I guess what I'm trying to ask is where am I getting my wireless signal from, the Access Point or the Router or both (assume I am in wireless mode).
View 4 Replies
View Related
Sep 15, 2012
I am currently using internet on DSL on Local Area Connection. It is not a dial up connection. I also have a WiFi access point. Now, I want my all the applicatons like browsers, Yahoo, Live Messenger etc. to use internet through LAN as usual but there is this application for which I want to use internet for through WiFi, not LAN. Just like Proxy Firewall, you choose for different applications the different proxies. Like this, I want different connections for different applications.
View 3 Replies
View Related
Dec 25, 2011
how to access the secure WEB encryption wifi accesspoint?
View 2 Replies
View Related
May 18, 2012
I am using Windows 7 and Netgear router and trying to set up the wireless network and keep on receiving the message - problem with wireless adpator
Is this a known problem with Netgear WGT624 router?
View 1 Replies
View Related
Oct 23, 2011
I have 7 on both my laptop and tower PC, I share my entire D drive from my tower over the network (homegroup)... i like to keep a mirrored copy of the drive, so I can copy everything from the D drive to the laptop.Absolutely everything copied EXCEPT one folder. I have no idea why this folder will not copy... windows just says "you do not have permission to access"I've done this plenty of times before, never changed the attributes of the folder or anything. I recently formatted both of the systems so everything is nice and clean, no system problems or anything.
I tried moving the folder to another location on the D drive but it's still says I do not have permission... I try just sharing that particular folder, full control, but it sill says no permission.However, I've copied a few of the sub-folders to another location, and I CAN access them. So it must have something to do just with that folder
View 1 Replies
View Related
Nov 12, 2012
I am trying to configure a Netgear WNR3500 router to be used as an access point.My AT&T U-Verse Gateway router is in the basement of my house and the WNR3500 is in my office on the second floor of my house. I am using the Netgear Knowledge Base article ID 19852 titled "Set Up a Wireless Router as an Access Point on a Network".In Step 5 is says in Advanced tab Setup > LAN "In the IP Address field, change the LAN IP address of the router (WNR3500) to 192.168.1.100 (same IP segment of the main (AT&T) router (192.168.1.1) and uncheck the DHCP server box.I did that and the wireless access point doesn't work.The AT&T Gateway wireless router IP address is 192.168.1.254. I also tried changing the WNR3500 LAN IP address to 192.168.1.200 and the access point still doesn't work.
View 5 Replies
View Related
Jan 17, 2012
how to access my desktop that is on my Homegroup. When I try to access my desktop from my laptop I get asked to "Enter Network Password". The password I used for my router and my homegroup are both not working and I tried changing my homegroup password without avail.
Can I just completely turn off the homegroup password? On both computers I have opted to turn off password protection for the network but it doesn't seem to change anything.
BTW, I can access my laptop via my desktop but just not vice versa.
I have tried to find user guides but nothing seems to help. I can't even leave the homegroup on my laptop which I find weird.
View 12 Replies
View Related
May 11, 2012
I am having a hard time configuring my Access point. I have a DSL Router connected to our telephone line and it works fine wirelessly, Yesterday I purchased TP LINK Router to configure as Access Point to extend wireless signal up to the second floor. Now, I am wondering, should I do some re-configuration on my DSL Router before configuring my TP Link Router? Guys, Please share your thoughts and if you have knowledge on how to configure my 2nd Router to my WifiNOTE: I followed the user guide manual that came with my TP LINK router but it is no USE. I just need to know if should I reconfigure my 1st Router in order to communicate with my 2nd Router.
View 4 Replies
View Related
Jul 25, 2011
i have big mindf*** going on here..i have 3 computers,
A - Windows 7 ultimate x64 (PC) (LAN connected)
B - Windows 7 professional x64 (laptop) (WLAN connected)
C - Windows 7 ultimate x32 (laptop) (WLAN connected)
Theyre all connected on the same HUAWEI B260a wireless gateway, and theyre all under the same workgroup and connected within a homegroup Standard shared public libraries (music, picture..) are visible and accessible for all of them with each other.PROBLEM is @ network location
1) when i access from computer A to comp's B hard drive partition its all ok but it cannot access shared partition on computer C (but its visible)
2) computer B cannot access either one of their partitions
3) computer C can access everything and all All of the HDs partitions are shared?
how can i share my PARTITIONS and make them accessible for each computer without having permission troubles?ive even assigned static ip adresses for each computer (though they comunicate with each other ok so it wasnt necessary to do that)ofc, partitions are shared, FWs are disabled, all of the necessary services are enabled, there are no AVs blocking traffic - but because of line under * stated above, nothing of this is actually important?
View 4 Replies
View Related
Jan 23, 2013
I have setup a Homegroup for a desktop and 2 laptops. All computers have joined the Homegroup and the 2 laptops can see files on the other computers. However, when I try to access the other computers from the desktop, I'm asked to sign in. I enter the other computer user's name and since neither has a password I just click on OK. Then I get a message that says I don't have permission to access the files. Why am I asked to sign-in only on my desktop? Do I need to setup passwords on the laptops?
View 9 Replies
View Related
Jun 2, 2012
I have two computers running Windows 7 and both belong to a Homegroup. From one computer I can access both computers and from the other I can't access the other. It say's I don't have permission but I gave it everyone permission when I shared it. I can't figure out why?
View 1 Replies
View Related
Nov 26, 2012
The HomeGroup shares have been a recurring issue that I haven't been able to solve, but the really perplexing one is the shared folder issue which just cropped up. Some of my shared folders still work, but e, g and h (music and video respectively) for some reason spit back "Access Denied" on all of the other computers in my house, this is in spite of the fact that Permissions on them are set to Full Control for Everyone.With regards to HomeGroup shares, they simply don't show up no matter what I do, I'd like to fix that one too, but I'm not sure what I can do to fix that.
View 1 Replies
View Related
Apr 28, 2012
I wouldn't go so far to say, I'm totally computer illiterate, but not far from it.. If there's anyone out there, who's up for a challenge I'm running windows 7. I am the administrator. Someone I don't trust at all, used my PC a while back. After he (did whatever he did) I noticed I couldn't access several files. I get a "access denied" or you don't have permission to view this file, owner info etc.. I can see a lot of the files, but their either empty now or I can't view them. I have used restore many times in the past, but now I get a message " no restore points".. I don't know what he did, or if he did anything.. It could be one of my kids changed properties by mistake, before I wised up and created a basic user acct w/ limited access for them.. I almost forgot. When I go into file properties there is a red x by my user name (administrator) Not in every property, but several.. Sometimes there is a red x by other user names, as well, but mostly mine.
View 3 Replies
View Related
Jan 23, 2012
In a few days time I will be changing my ISP in the UK from Sky to BT.
BT are providing me with their newest wireless router free of charge as part of the deal and I'll be using that to set up my wireless network, which will consist of an HP Pavilion desktop, a Toshiba laptop, a Sony Vaio laptop, an HP wireless printer and a Samsung HDTV.
This means my Sky wireless router is surplus to requirements, so I was wondering if I could convert it to a wireless access point to improve the range of my BT wireless network.
I've read a couple of supposedly easy-to-understand articles on Google and have to say they left me more confused than ever.
View 6 Replies
View Related
Aug 3, 2012
I installed Windows 7 on my laptop, and I also have a desktop running Windows 7. I am trying to connect my laptop to my homegroup with the password for my homegroup, but my desktop will not reveal it. Is there any other place that I can find it?
View 1 Replies
View Related
Aug 28, 2011
I have an issue which I can't find anything obvious on.I have 4 Windows 7 machines, 1 x W7 Pro, 2 x W7 Home Premium & 1 x W7 Starter all in the same Homegroup.The W7 Pro machine can see all the others under Homegroup in Windows ExplorerAll 3 of the others can see each other in the same way but the W7 Pro machine isn't listedThe 3 others can access the Shares on the W7 Pro Machine by going to Network rather than Homegroup in Windows Explorer.
View 1 Replies
View Related
Oct 6, 2012
I dont know what happened to me suddenly my antivirus AVG 2012 detect an intruder on the web browser and remove the browser morzila and after that I have no restore point but i dont know what happens and I feel that my PC has something strange how I can solve this problem?
View 1 Replies
View Related
Dec 1, 2009
As I've read over and over, it seems to take at least 4GB RAM to unleash the power of 64 bit computers. That being said, why do the PC makers install only 2GB and says it's not upgradable. In the future, will I be able to get a 4GB RAM upgrade for it. Had I paid attention when purchasing, I would have noticed.
However, my PC runs fine for me now, but what if I want to install some RAM hog programs? This is almost 2010, not 2000, when if you had 512MB RAM, you had something. But I assume that in the not too distant future, a 4GB option will be available to me.
View 9 Replies
View Related
Aug 25, 2012
can u do a restore point for another hard drive and not c:drive system disk?
View 4 Replies
View Related
Jul 4, 2012
Ive used DOS then Windows all my computing life (which happens also to be all my life) and i recently converted over to primarally using Unix Derivitives. Now Unix derivitives such as linux have a etc directory which stores all the conf and unmarked configuration files while DOS uses interdirectory INI files for configuration... WHile windows uses INI files, appdata directories in each user directory, a program data root directory, configuration directories in the windows/system32 directory AND the registery...... What is the point of it all, the registery is a great single point of failure and its redundant.
View 4 Replies
View Related
Aug 6, 2011
I need to a system restore point file without getting into the desktop through Windows 7.
View 3 Replies
View Related
Jan 30, 2012
I have a PC with win 7 pro 64 bit which has been working fine for months. A few days ago, I fired up the PC and noticed an old wallpaper and some application icons in the desktop were missing and some that I had deleted suddenly back there. I looked at the restore points and there are none older than a few weeks, but this particular config is 8 months old. When I try and restore to a more recent recovery point I get an error message telling me that there is an invalid parameter.I rebooted the PC and all was well again for a day but now it has reverted to the old config and nothing seems to shift it.My data is intact ( backed up as well ) but I am at a loss as to a) what to do next and b) what caused this problem
View 6 Replies
View Related
Oct 26, 2012
hey should i create an restore point right away before i start scheduling them in ? just to be sure it all works first?
View 1 Replies
View Related
Dec 31, 2010
I have two hard drives. C: drive and a D: drive.
Is there any way to point the Recycle Bin away from the C: drive to the D: drive in Windows 7 Professional?
View 9 Replies
View Related
Nov 18, 2009
I was having problems with my i7 system freezing during installation. After reading through these forums I removed 2 sticks of RAM, my sound card, and my wireless PCI adapter and both of my WD hard drives. Everything's working now!
My question is at what point should I start reinstalling my hardware? Should I install my mobo drivers first? Can I also add everything back in at once now?
By the way, these forums seem really helpful! I'm looking forward to browsing through the different forums here!
View 4 Replies
View Related
Feb 24, 2012
How do I pdf A TABLE FOR THE THUMBNAIL point to the document
View 3 Replies
View Related
May 10, 2012
I have received email PPS, 13 Mb. But I cant open it with my new laptop. OFFICE HOME and STUDENT 2007 is installed. But I can open it with my old computer of 32 bits where Office home and Student 2007 is also installed (same CD).
View 2 Replies
View Related
