i just nstalled windows 7 64 bit ultimate on a custom build. i have video at the start then with the windows circle spinning the video just goes to black. the system works good in safemode.
View 3 RepliesI have a new Dell laptop running W7. The screen tint is far too blue and I have found the controls in the display section where I can modify the colours (and gamma etc).
I can adjust everything with no problems, but much to my annoyance, when I boot up again, all the settings have reverted back to the factory, too blue settings.
(I think that the settings even get lost if the laptop powers itself down through the various hibernate/sleeps etc; although I'm not that familiar with all of those options so am not sure.)
So, my question is how can I get W7 to remember these settings?
Windows 7 64 turns off the monitor 1 signal after startup. At login, it powers off monitor 1 and powers on monitor 2. Windows 7 behaves as though dual display is working even though monitor 1 does not display. It's the same for single display, the monitor will not work on cable 1 except at startup.Both 'Extend these displays' in Windows Screen Resolution and 'Extend' in the Nvidia Control Panel is selected. And changing which one is primary does not turn on monitor 1. Nor does switching the position of display 1 in either (ex.left/right/top/bottom).GeForce 8400 GS; Dual Monitor Solution 59 pin (DMS-59) to 2 VGA adapter -tried two of these adapter cables.atest Driver: 306.23 - installed a clean reset install of the latest Nvidia driver released last week.Same Resolution: 2 of the 4 monitors I have tried have the exact same 'recommended' resolution (1280X 1024), both 60Hz, and even chose 16 bit color for both instead of 32 to reduce resources.
Linux worked: Dual display worked immediately when I tried it in Ubuntu 10. So, it's not the hardware. It works in Ubuntu 12 too but not properly -it won't transfer windows across displays. My Windows 7 64 is an upgrade from Vista 64. One person in another forum with the same problem resolved theirs by reinstalling Windows 7. But another got the same problem only after a fresh clean install of Windows 7 64 with the same GeForce 8400 GS and DMS-59 when it had previously worked in Vista. Dual Monitors - Only One Works at a Time
I just got a new 9800gtx+ . i have a 22" AOC lcd screen. whenever i start my pc , the motherboard screen appears but when the windows loading screen comes my monitor shows the message input not supported I have updated my drivers and checked fastpccheck.weebly.com. but no help. After that screen the user login screen comes to display and then everything is normal. i cant figure out what is making the problem.
View 5 Replies View RelatedWhen I turn on my HTPC it displays the Windows 7 Desktop for a bit before being able to open Media Center. Is there a way to have Windows 7 not display the Desktop if it knows Media Center will be opening thereafter?
View 1 Replies View RelatedI am rebooting "Windows 7" more than any prior version of Windows for one simple reason. When my computer comes out of a sleep mode and I click to log on to an existing session, the keyboard can no longer be used. Often when I attempt to type on the keyboard, the mouse is then lost as well.
If I instead log on and then immediately do a restart - everything is fine. So, now I have fallen into the habit of restarting every time. It takes less time for me to do that then getting something started with the mouse and then freezing the system by trying to type something. So I just accept the restart and avoid the reboot. But, essentially the restart is a reboot.
Very frustrating! Then a few times I have gone directly to the Microsoft website and they do not even mention the issue in their database. It's like no matter how many people mention the same "windows 7" "loses keyboard", Microsoft just does not care. It goes against all the other facts that say "Windows 7" is the most stable version of Windows.
When I start my computer with drivers installed my monitor loses the signal when I should be receiving a log in screen. I can boot up fine in safemode and/or if I'm using Standard VGA Graphics Adapter. To my knowledge I do not have an onboard graphics card as there is nothing to plug an avi or vga cord into aside from my graphics card. I should also mention I tried using an NVIDIA GeForce 8500 GT and experienced the same problem.
View 5 Replies View RelatedWindows 7 keeps minimizing every hour to desktop no matter what is running. I ran process explorer just before the time it should lose focus and only one program launched a minute before it does so, taskhost.exe. I tried to run with all processes killed (including explorer.exe) and that also gave good result, it didn't minimize, however I know not which of the processes does this.I first noticed the problem as screensaver quits on it's own after a while (despite the fact it has to quit on click or key press)
View 1 Replies View RelatedI keep losing LAN connection within 1 minute after my computer wakes from sleep modeI cannot ping the router, the DSL modem and anything outside.Windows "repair connection" tool fixes the problem until the next time I put computer to sleep.have Windows 7 32 bit, integrated Intel LAN card. Can't blame McAfee because when I uninstalled it and replaced with Microsoft Essentials this behavior didn't change
View 1 Replies View RelatedI don't know if this is a harware issue with my SSD, disk controller (motherboard), power supply or something else, but depending on what I'm doing, the computer will operate for a few minutes then freeze and eventually reboot itself. When it reboots, I get the "Bootmgr is Missing" message until I cycle power a couple of times. I've tried booting from the Windows 7 repair disk and typing "bootrec /fixboot", but the problem eventually returns.I can't get a full image update from Acronis because it hangs in the middle of the image, even if I say to ignore bad sectors. If I run the HDTune diagnostic on the SSD, it seems to always stop after about 3 minutes and always in the same spot, at 15,432MB. Is this a problem with the SSD or the disk controller?
Configuration:
O/S: OS Microsoft Windows 7 Ultimate (6.1.7601 Service Pack 1 Build 7601)
Motherboard: Gigabyte GA-MA78LMT-S2
CPU: AMD Phenom(tm) II X4 840 Processor, 3200 Mhz, 4 Core(s), 4 Logical Processor(s)
BIOS Version/Date:Award Software International, Inc. F13, 8/31/2010
SSD:Microcenter SSD G2 series 64GB ATA Device
HDD:Hitachi HDS721010CLA332 ATA Device (1TB)
RAM:8GB
I don't know if this is a harware issue with my SSD, disk controller (motherboard), power supply or something else, but depending on what I'm doing, the computer will operate for a few minutes then freeze and eventually reboot itself. When it reboots, I get the "Bootmgr is Missing" message until I cycle power a couple of times. I've tried booting from the Windows 7 repair disk and typing "bootrec /fixboot", but the problem eventually returns.I can't get a full image update from Acronis because it hangs in the middle of the image, even if I say to ignore bad sectors. If I run the HDTune diagnostic on the SSD, it seems to always stop after about 3 minutes and always in the same spot, at 15,432MB. Is this a problem with the SSD or the disk controller?
Configuration:
O/S: OS Microsoft Windows 7 Ultimate (6.1.7601 Service Pack 1 Build 7601)
Motherboard: Gigabyte GA-MA78LMT-S2
CPU: AMD Phenom(tm) II X4 840 Processor, 3200 Mhz, 4 Core(s), 4 Logical Processor(s)
BIOS Version/Date:Award Software International, Inc. F13, 8/31/2010
SSD:Microcenter SSD G2 series 64GB ATA Device
HDD:Hitachi HDS721010CLA332 ATA Device (1TB)
RAM:8GB
My netbook loses its IP address after it has been asleep overnight or longer. I cannot do an ipconfig /release or ipconfig /renew. It says there is no media. My only recourse is to restart. My laptop does not have this problem.
View 7 Replies View Related1. Computer, at start up, sometimes can't find my monitor. Only way is to start the computer with the monitor switched off; then turn the monitor on at a certain time during the booting process (when I here a motherboard-beep). Occasionally the connection will be broken anyway (and I'll have to mess with the 'reset/-start button). I generally get to the motherboard page and BIOS settings. But sometimes not even that and then the only solution is to leave everything off for a while (minimum a couple of minuts – but not exactly sure).
2. Computer lose monitor when it to goes into sleep mode. This only happens if I leave it inactive for a long enough time. I can usually retrieve it if the display's gone out only for a short while, as usual - by pressing keyboard or moving mouse.
My hope is to find a solution that doesn't involve buying a new monitor.
Got a PC with Nvidia GeForce 6150 graphics card with no overclocking. Sometimes the monitor loses signal and does not work. Sometimes it works just fine. I've tried different VGA cable and different monitor, situation didn't change. I've got 4 different connectors.
- 1 VGA and DVI on Nvidia
- 1 VGA and DVI built in into motherboard.
Sometimes, when the Nvidia doesn't work, I connect to built-in card and monitor starts working. Next time when it's out, I connect back to Nvidia. There have been situations when only one of the four connectors is working. This means that on one graphics card there may be only one connector which is functioning. I don't get this. Problem isn't in the display nor the cable. It also doesn't seem to be in the graphics card as the built-in connectors aren't fully functional neither.
All of a sudden Snipping Tool is losing anything I try to save in jpeg format. It says it saves in the folder where I asked it to but nothing is there. When I redo the snip it tells me that file already exist. When I do a search the file shows up as being in as a Recent file used but nowhere else.
View 2 Replies View RelatedI turn on the computer, goes past the bios screen as normal, does the windows loading screen as normal, then the screen goes black and the "No Signal" message is displayed.
Now, here is why it is different. I type in my password and press enter, without being able to see and wait for the logon sound to play, then if I unplug monitors cable, I hear the noise of windows telling me a device has been disconnected, I plug it back in again the device connection noise then plays and low and behold, there is the desktop.
I have been running Windows 7 build 7100 for roughly about three weeks until this started happening about one week ago.
MONITOR: ViewSonic VX1932wm
GPU: Sapphire HD4850 512mb
Also, I have noticed too after logging, randomly Aero will disable itself, I have to open the 'Personalize' option and run the troubleshoot to get it to fix itself again.
I assume this is the correct section, as I am experiencing visual issues. Apologies if this is not the correct section.
I am noticing that if the OS is unexpectedly shut down then all the state data in IE is lost. I am assuming it is cookie data. An example is Google preferences. I set it to display 100 results per page, not filter my results and open in a new window.
Every time the computer is "accidently" powered off upon reboot Google reverts to showing 10 results per page, filtered results and opening in the same page (the default settings). This goes for every site that I have remember my login name.
I am runing Windows 7 Build 7100 RC1
I am curious if anyone else is experiencing this issue.
Whatever modem/router I use (except my old 2Wire that died in Dec. 2010), I lose connectivity after I resume/wakeup. The tray icon says "connected", but my browser (Firefox) or my email client (Thunderbird) say "no"!
View 3 Replies View RelatedIts been like this for a while now. That is every time i leave my computer on for over a day it loses its ability to load webpages. A simple ping to [URL] gives a timeout while any other computer on the network can still access any other website (including google.com). I suspected a failure of my computers DNS to convert DN's into IPs however a flushing and reactivating of the computers DNS cache still does not solve the issue. If i still have MSN or uTorrent running they seem to be able to connect to peers over the internet which is strangely odd, however signing in and refreshing trackers no longer work. I have tried accessing websites with the latest version of IE and FF while this problem persists.
All network settings are on automatic and i use Windows 7 SP1. I have a phone that alerts me to new mail and i have suscribed to this thread.
Fujitsu M1450G is losing its internet connection after a few minutes of internet browsing, the wireless connection says it is still connected, but internet doesnt work. I also do a repair on the connection but it doesn't solve the problem. I have to restart the laptop each time to have internet again, and it will only last a few minutes usually. What can the problem be and how can I solve it?PS Laptop location doesn't seem to be the issue, tried it just a metre away from the router and it has the same problem. Other laptops in the house have no problem at all.
View 9 Replies View Relatedi just recently built a new gaming rig and am running an SSD for boot up.
Everything turns out just fine except when after the windows logo appears, I can hear a little crackle noise from my headphone then the monitor loses signal and my g15 keyboard LCD turns off, then a few moments later my monitor and keyboard comes back to normal and i am a the login screen. It is not a big deal but am just puzzled at why it would do this.
It does slow down my boot speed by a lot especially for an SSD. Anyone know how i can speed this up? Someone told me disable USB 3.0 to speed things up. Any problems with Asrock MOBO drivers that could affect this?
I have desktop that is less than 2 years old and it is having two problems: First, if I step away from the computer for a few minutes and come back to the computer, the screen is black and none of the keys will wake up the monitor. Also, I am unable to turn off the tower, even when holding down the button for 10 seconds. The only way to turn it off is to unplug the tower. When I plug it back in, I get everything back on the screen just like it was before I walked away.
The other problem is that the system clock will not keep time. This just happened a week or so ago. Whenever I manually update the sync, it resets, but won't keep time for long. From reading other posts on this forum, it seems that the CMOS battery may be an issue. Since the computer isn't that old and isn't used constantly, does that still seem reasonable? Is that normally covered under a warranty? I have never had a problem with other computers.
For some reason , my computer restarts without notice , just seems to lose power all of a sudden, then it will start up again..This generally happens when CPU usage is at 90+% some games that have been doing this areCrysis 2 << (even on low)ApB Reloaded <<(lowest settings as well)Nba 2k11
View 3 Replies View RelatedSo. Running XP.2 (can't run XP.3; it kills Adobe's CS2 apps, which I need). Had a spare partition. Before putting Ubuntu back on it, I figured I'd install the Win7 Ultimate that'd come (unused) with another computer.
(The install was smooth enough. The updates were slower'n snail poo. But after turning almost everything back to the Windows Classic theme, it's almost bearable. Only two of my devices were unrecognized and unsupported, and they're no surprise; the tablet's nearly twenty years old (even the manufacturer doesn't support it) and the scanner's older still.)
Installed copies of my must-have software--Office 2003 (I've had to suffer through Office 2007, and will never ever ever put it on a machine I have to work on), Photoshop and InDesign CS2, Winamp .
I got my first real exposure to User Access Levels when, the first time I ran Word 2003, Win7 wouldn't let me save the new Normal.dot. I later went and copied my much-customized normal.dot from its XP location, so the file's at least there.
But: I run Word on a portrait-oriented monitor. Under XP, Word remembers the window size and position, and it's exactly where I want it, all the time. So far, every time in Win7 I've opened up an existing document, the Word window has instantly shrunk to around 40% of the size it's supposed to be.
I'm curious if this is a cling-on permissions issue with normal.dot under Win7, or a registry setting that simply hasn't gotten made (in XP, Word seemed to take care of remembering where I put and closed it by itself). Did a search, but didn't see any questions that seemed to relate to this, so I'll ask.
(I'm trying to like Windows 7, I really am. I don't much, but I'm trying. I don't mind the thought of getting a new tablet, and I've got another scanner I can use. But I really dislike having to resize my windows every time I open a document--I spend 75% of my time on the PC in Word, just writing.)
And again, I hate, loathe and despise Office 2007 and 2010. I do most emphatically not like the "death by honey and marshmallows" interface that microsoft seems to think is so great.
I have an Asus G50vt-x5 laptop (with windows 7 now, originally had vista), and my old battery was losing charge so quickly. So, i got a new one. I did everything you were supposed to, charged it up, discharged it, charged it again, etc.For some reason, i can just be playing or doing things on my laptop, and it'll randomly just lose ALL power. For example, i was playing a video game the other day and was at roughly 65% battery, and suddenly the computer just instantly died. And i don't know if any of you have seen an asus, but there is a little light on the panel with the power button for like a "quick start", and that light is ALWAYS on. but when the laptop died it wasn't. Which i take it means absolutely no power was going to the laptop.
View 9 Replies View RelatedEver since I bought my new computer and installed Windows 7 64 bit Pro I have noticed that sometimes when I start my computer the startup locks up or crashes, requiring me to restart or it takes me to the system repair screen and running this process does nothing.
View 9 Replies View RelatedI have a Dell Inspiron and a while ago I shut down my PC and the next morning I was faced with options to repair my computer. It hung on the screen for ages before it actually came up with startup repair and supposedly fixed the problem. A few days later, everything got very slow and started to freeze a lot and before long, booting the computer got very slow as well as it hung for about ten minutes on a black screen after the 'welcome' screen before finally starting up. I decided to reinstall the operating system (I did NOT reformat the C drive), so I borrowed my Grandma's external hard drive and copied my files. After reinstalling using a Dell Windows 7 64-bit Home Premium Re-Installation DVD, I copied and deleted the files off the external hard drive onto my PC (I didn't know it would create a Windows.old folder) and started installing programs. Then I left it overnight to install quite a big program. This morning, somehow it had turned off. I turned it on and it gave me the safe mode options and a 'start windows normally' option. I chose the latter and after typing my password it hung on the welcome screen again. I left it for ages and it just went back to the user login screen again. I pressed the red button in the corner to shut it down but it just hung once again on an empty screen so I did a hard shutdown (held down the power button). I turned it on again...startup repair. It gave me the option for system restore, which I did (then realising when it finished that I hadn't made a backup). I booted it, and again it wouldn't start properly. At this time, safe mode booted fine. After trying various things (even using a compressed air can to get rid of dust) and a few hard shutdowns, suddenly every option from the advanced boot menu took me to startup repair except 'Repair your Computer' which gave the normal options for repair (although now it only gives me 2, Startup Repair and DataSafe Restore and Emergency Backup. Now when I do startup repair, some times it says it has fixed the problem, and sometimes it says it cannot be fixed automatically and gives me information on the problem (a few things it said were: 'StartupRepairOffline', 'AutoFailover' and 'CorruptRegistry').
I can't reinstall my computer because then I would lose my precious files.
Is there some way I can save my files and reinstall or even just save my files somehow or am I screwed?
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit
Processor: AMD Athlon(tm) II X2 240 Processor, AMD64 Family 16 Model 6 Stepping 2
Processor Count: 2
RAM: 2815 Mb
[code]....
Antivirus: The Shield Deluxe Antivirus, Updated and Enabled DISPLAY MODEL: All I got with it was mouse and power cord On Startup, I get icons for the Administrator and Standard user. Clicking on the Administrator gives me a desktop with an on-screen keyboard; the computer keyboard disabled, and a panel saying,"FAILED, The application has failed to start." Going back and clicking on the Standard User icon gets me running for the most part. Here's the BIG problem. Every time I try to install any program, the User Account Control box drops down and asks for the Administrator Password, plus the question,"Do you want to allow the following programs to make changes to your computer?" You click "Yes", but, since no one is in the Administrator office, your installation comes to a halt. This blocks "Install" and "Uninstall". I get lots of messages I need Adobe Flash Player. I've trie over and again to install it, going to Windows 32 bit, but can't uninstall my previous tries. It will always download, and that's all. I've tried to install my digital camera's CD, but can't.
the display/monitor uses the generic driver for display and it is 1024×768 or 800x600 but it looks very odd it should be bigger because my screen is bigger. I have a acer monitor but is there something I can download to fix the display size?
View 3 Replies View RelatedI hate it when this happens and so far, the startup repair has always been able to fix the problem. Today, I'm not so lucky.
I'm using my other built right now coz I have to work. I don't remember what updates I did last night but I do remember the dvd drive firmware was updated.I popped in the system restore disc, start it up and the same page appears: Start with windows start up or Start windows normally. Tried both and neither one of them would bring up system restore. This built was only a month old and was hardly used so far so no system restore point was created at this point. I have files in it that I would like to keep but I can't get to them right now so a clean fresh install is needed but I can't get it up.
i used to get the BSOD very often so i decided to recover the system to the initial state . i did that and everything was fine , then i updated the windows 7 service pack 1 and finished the installation and rebooted my computer , the start-up at least took half an hour at that time and the service pack 1 installation showed "not successful " i tried to again to update the service pack1 which showed 73.6mb - 892.6mb so i updated it again and again the same thing happened.
View 7 Replies View Related