Win7 64 bit reports a problem with the driver for Microsoft ISATAP Adapter and Toredo Tunneling Adapter. Troubleshooting does not automatically fix it and reports that the drivers are OK. I have seen several other reports of this problem but not yet found a cause or fix
View 6 RepliesThe comp started BSOD'ing out of nowhere, a new adapter I think called ISATAP or something like that shows up under network adapters in device manager which had a yellow exclamation icon. (Code: 31). Disabling or uninstalling its drivers resulted in BSOD's. Googled around and found the only way to fix it was to delete some registry entries, so without backing up the registry I deleted some keys. I don't remember which keys but the image above is the result. I got Ubuntu live booted up and using it to post this because my Win 7 installation obviously can't connect to the Internet.
*I tried reinstalling drivers (Marvel Yukon & Belkin), disabling and enabling stuff but nothing seems to be happening.
*Got some registry fixing tools or whatever, still the same.
I am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all. Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box.
When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".
miniport network adaptor
View 2 Replies View Relatedwhere and how do I get drivers and network adapters for hpg6 without installing into my friends computer
View 1 Replies View RelatedToday, I managed to redecorate my bedroom; where my computer sat on top of a shaky, wooden desk. That desk is now gone, caput, and replaced by a much bigger, sturdier and prettier glass replacement.Before I dissasembled the computer to re-decorate, I was able to browse the internet at ease. There were no problems at all...However, after the new desk was setup - and all wires replaced in their correct slots, I find that I am unable to connect to the internet, or even the house's network! For the past year, I have been wired to the router using a RTL8168C(P)/8111C(P) Family PCI-E Gigabit Ethernet NIC. It was plugged into an extension cord, in my room, into the Ethernet port in the back of my computer. Downstairs, it's twin was situated no less than 2 feet away from the router - plugged into the first port.Now, when I boot up the computer, the network notification presents the following message: "Unidentified Network. No network access", and sometimes presents a yellow ! next to it. So, I am reduced to typing on my mother's laptop - which has no problems connecting to the network.I am able to use the ipconfig /release command, but unable to use the /renew - it hangs in the command prompt, then tells me that the DHCP server cannot be located. The IP, beforehand, was reverted to 169.254.223.117 - before all of this, I was 192.168.0.5?
View 2 Replies View RelatedAnyways my problem is that my vaio is running Windows 7 64bit and suddenly one morning NONE of the network adapters were working. No WiFi, no ethernet, no nothing. I figured something just happened to the drivers (happened before) so i'd just reinstall them...except this time I'm hit with:
Code :This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
I have tried everything short of a full restore. I tried downloading the drivers straight from Sony, just the driver files for Atheros, I can't do a restore point since I don't have any from before the problem. I have searched everywhere for a working solution but haven't found anything yet. I would like to avoid sending it in.....it's still under warranty but I don't have a Sony store near me and I'm gonna be going out of town in a couple weeks..
3 PC's all running Windows 7 Ultimate
1 Desktop connection via wire to router
2 Laptops connected via Wireless (Linksys wrg54g)
All 3 PC's are visible on all 3 PC's via the Homegroup in Windows Explorer. I can browse/copy/write files on all 3. All sweet. All 3 can print to the 2 Printers connected to the Desktop.
Laptop A is configured to Backup using the Windows 7 Backup to the Desktop. This works fine.
Laptop B however when trying to backup to the desktop I get an error message after I have selected the Drive in the setup screen and I've entered my username/password credentials
The error code is 0x80070043
I've tried everything and I'm quite experienced.
Both laptops for all intents and purposes are identical.
I have a Desktop computer with Windows 7 (32 bit) and a laptop with Windows 7 (64 bit). I'm trying to set up a network printer, so I can print from my laptop using my desktop computeer printer. I've set up my wireless computer which uses Windows Xp just fine, and can print from that computer. But when I try to add a network printer on my laptop, as it's finishing installation, an error message pops up saying "cannot connect to printer" error code 0x0000000d. Any feedback would be greatly appreciated. Is it possible to set up a 64 bit with a 32 bit computer?
View 3 Replies View RelatedI installed Windows 7 on my computer a little more than a week ago from Windows Vista Home Premium. My home network worked fine, and I was able to connect to the internet, share files and everything perfectly. However, starting yesterday other computers on the network could not see me and I could only see one or two other computers on the network, and I couldn't see the main computer, i.e. the one with the wireless router.
When I try to click on that computer in Windows Explorer, the green loading bar starts to fill up, but then a window pops up that says "Windows cannot access "(Name of the computer). Check the spelling of the name. Otherwise there might be a problem with your network.
To try to identify and resolve network problems, click Diagnose. Error code: 0x80070035. The network path was not found." I click Diagnose and no errors were found. I tried removing the network from my network list and resetting it up, and nothing. What should I do?
I keep getting Error code: 0x80070035 The network path was not found error whenever I try to connect to any other computer (running windows 7 ultimate) on my network. I have another computer with windows 7 ultimate that does not have this problem. Firewalls are disabled on all computers.
Computers all ping fine. Can ping by name too. If I try to connect via IP address, I get Error Code: Error0x80004005 Unspecified error
Ok, I have a laptop and a desktop. Desktop is currently running 7 x64 and laptop is running 7 x86.
Few weeks ago I was able to access my LAPTOP from my DESKTOP normally by using the Network in the explorer. I was prompted to key in my Username and Password of my LAPTOP and I gained access after.
Now, I have no idea what happened to my DESKTOP. I am able to access other computers but not my LAPTOP. It keeps stating Network path not found with error code 0x80070035. Troubleshooting indicates no problems found.
I do dual-boot with Vista x64 on my DESKTOP and I am able to gain access to my LAPTOP using Vista.
One of the workaround I got for Windows 7 is to create HomeGroup and use my LAPTOP to join it and I can gain access to Network after that.
So, is this a HomeGroup bug and any fix for it?
EDIT: Never mind, I just re-create my password on my laptop and it's fine now. So, it's really weird.
When I try to create a system image on a network location Windows asks for Network credentials for the target location. The credentials I enter are correct but I always get an error message that the location can't be used because the password is not correct (Error code 0x80070056).
Is this a bug in Windows 7? Any way to fix or work around this?
At the moment I'm using Netgear AV200 powerline adapters and need to add 2 more adapters to my setup.Do I have to stick with Netgear or can I use another brand if they are both compliant with HomePlug AV1 standard and the same speed (200Mbps)Edit: Well apparently all powerline adapters are compatible as long as they are the same type (i.e. Homeplug AV or DS2), so I'll be getting more affordable pair of adapters...
View 1 Replies View RelatedWe have just purchased a new computer with Windows 7 at our office and we were told there weren't any wireless network adapters that were compatible yet for 7. All of the other computers are Windows Vista and they have Ativa Wireless Network Adapters that work fine. It will not work with this new computer. Any suggestions of how to get up and running on the Internet?
View 5 Replies View RelatedI keep getting Error code: 0x80070035 The network path was not found error whenever I try to connect to any other computer (running windows 7 ultimate) on my network. I have another computer with windows 7 ultimate that does not have this problem. Firewalls are disabled on all computers. Computers all ping fine. Can ping by name too. If I try to connect via IP address, I get Error Code: Error0x80004005 Unspecified error.
View 9 Replies View RelatedOnce I've started my computer the "Network" icon is kind of "searching" but after a while it becomes red like I have no internet access. But I do got internet, I can go the internet but I can't open anything in the start menu. Then after a while again, the icon becomes "normal" and everything works fine. The code I get when I troubleshoot is "0x80070426" and the troubleshooter wont start. This is kind of annoying, I am using Windows 7 ultimate.
View 2 Replies View RelatedMy problem is that i bought some 1gb belkin powerline adapters to give me a better connection in my house than my wireless previously did. However i plugged them in and boom "Unidentified Network - No internet access".Now at first i thought it was because i had them plugging in through and extension lead downstairs so i removed all than and plugged them straight into the wall. This didnt help at all.I read some forums about turning of IPV6 cos apparently.
View 9 Replies View RelatedI have several VPNs and Virtualizing software installed, and they have this virtual network adapters in the network and sharing centre. In the "connect to a network menu", one shows working internet connection, while the other one shows no internet access, How do I get rid of those entries? I dont mind messing with the registry or the system files.
View 2 Replies View RelatedWhenever I boot up or disable/enable a network adapter it takes 1-3 minutes before I actually connect. After waiting, I'll see the little round circle spinning in the system tray and then i'm able to connect.While waiting for my adapter to work I noticed under tcp/ip settings that my gateway field is blank. If I put it in and go back, it's still blank. When the adapter finally connects it then shows up in the gateway field.Tried uninstalling AV, different drivers for LAN and wireless and reloading OS.
View 7 Replies View RelatedI have this device "WAN Miniport (IKEv2)" under Network Adapters and it's always listed as not working. I disabled it a long time ago but it always comes up as an error when I scan my computer. It won't update the driver, Windows always says that there was an error, and as far as I can see it doesn't do anything but it won't let me remove it even though it isn't working.
View 8 Replies View RelatedUpgraded to windows 7 ultimate 64bit from vista ultimate 64 bit. That didnt fix it. I'm desparate. I've tried everything I can find. It has a realtek 8169 nic on board sabertooth x85. I tried USB adapter and where it normally loads it just says it's installed but shows up in device manager. Like thw tealtek nic with yellow triangle on it. If I try an update driver it returns "parameter is incorrect" message. Its not connected and the is no IP using ipconfig. I Lost all my software CDs and emails with serials etc in a house fire last year.
View 6 Replies View RelatedI am running Windows 7 Home Premium (64 bit) on a Dell Inspiron 560. I am using a DI-524 D-Link wireless router. I have an Acer Aspire One Net Book running Windows XP Home it is equipped with an internal wireless network adapter. I can connect/communicate with router and access the internet with no problems whatever. However, when I connect an external wireless network adapter e.g. Alpha AWUS036H I cannot get a connection when I disable my internal network adapter. I have also tried the Trendnet TEW-424UB USB external wireless network adapter and the symptoms are exactly the same. If I leave home and use another Wireless point of access I have no trouble connecting using the external adapters which means the problem is confined to my personal home network. I have removed and reinstalled my router, and the network adapters drivers etc. I have uninstalled my Norton Firewall and and disabled my Windows firewall to no avail. I have removed my WEP security features and tried to run it open with no improvement. I have connected the external network adapters on a neighbours computer running XP to see if I could connect to my home network. That didn't work as well. Bottom line is I simply cannot get an external wireless network adapter to work with my router. Yet my internal netbook adapter connects with no problems at all.
View 2 Replies View RelatedI have over 50 virtual networking adapters in device manager, I have posted this question in many forums, and still cannot get rid of these pesky unused extra adapters. I know they have been created by using Virtualbox, and by creating many virtual machines and updating virtualbox. Unfortunately, I have tried uninstalling virtualbox and the drivers all remain in devicemanager. DeviceMgmt also does not allow me to uninstall or delete the adapters, (When I do they just stay there, even after rebooting.)I most likely have to go into the registry and delete them, but they are in so many different places there, I need to know the correct place to delete them. I have a bet that this is the forum where I will get the answer for this even though I have posted in virtualbox forums, technet, MSDN, superuser, serverfault, and stackoverflow.
View 7 Replies View RelatedI have had my vista pc and my windows 7 (basic) net book setup to let me share files (through an Netgear DG834PN Route) for around 18 months with no problems.
However as of 3 days ago I can no longer do this and non of the network tools can fined or solve the problem. I can uses the internet though my rooter, see my vista pc on the network as well as the media streaming (windows one) thing.
I can also access my net book hard drive from my pc no problem and transfer/delete files as well?
When I do try to connect the following error message is given: "Error code: 0x80070035 The network path was not found"
P.s. I know windows 7 basic has not create home group ability, but it worked with the one I made on vista. I can not afford to upgrade my copy of windows 7 so that is totally out of the question.
How to Install Ralink based Belkin Network Adapters ?
View 0 Replies View RelatedHow do you download legacy hardware i need to install network adapters ISATAP and teredo tunneling and 6to4 adapters cause its giving me a code 10 error
View 1 Replies View RelatedMy Network Adapters has suddenly disappeared after a Critical update by Windows update, now my network is X'ed out. I already did reformat and still nothing and in the past all I do is to System restore but after a while it had errors and I was forced to reformat but after that there's still no connection.
View 5 Replies View RelatedIn Windows Home Premium 64bit we encounter this problem on a machine after trying to uninstall a norton product manually.The norton software led to serious problems of randomly emerging BSODs.As system uninstall did not work we researched a tutorial on how to manually uninstall the soft.t can be found here Enterprise Support - Symantec Corp. - How to manually uninstall the Symantec Endpoint Protection client from Windows Vista, Windows 7, and Windows 2008 R2 64-bitEverything worked smoothly until the last three steps of the routine failed (12.-14We can not uninstall/delete the wireless network adapters as described. After clicking "uninstall" there is the window that asks for confirmation (to uninstall) but after clicking "yes" the device manager window simply refreshes - and the device remains unchanged.
View 4 Replies View RelatedI recently uninstalled all of my wireless network devices, these were a simple Wireless Card which was in a PCI slot and a wireless USB adapter, I uninstalled them from the device manager, and now under "Network Devices" I have about 32 'Microsoft 6to4 adapters' all with the yellow triangle on them, and then also there are 2 Microsoft ISATAP adapters, again with the yellow triangles. also, when I click on them, they say "This device cannot be started (error code:10)"And also now, my fast ethernet port has a yellow triangle on it too, but windows cannot find a driver.
View 1 Replies View RelatedI'm using Alienware desktop with ATI Radeon 5900 graphic Card I have problem though whenever I play World of Warcraft game not always but a lot of times I get a blue screen error but before the blue screen error I get disconnected from the game then It tells me that my display adapter stopped working somehow..I don't know why then the blue screen of death appears and my pc get restarted I have this problem for 3 months now
View 6 Replies View Related