Cannot Access Router With External Network Adapters
May 31, 2011
I am running Windows 7 Home Premium (64 bit) on a Dell Inspiron 560. I am using a DI-524 D-Link wireless router. I have an Acer Aspire One Net Book running Windows XP Home it is equipped with an internal wireless network adapter. I can connect/communicate with router and access the internet with no problems whatever. However, when I connect an external wireless network adapter e.g. Alpha AWUS036H I cannot get a connection when I disable my internal network adapter. I have also tried the Trendnet TEW-424UB USB external wireless network adapter and the symptoms are exactly the same. If I leave home and use another Wireless point of access I have no trouble connecting using the external adapters which means the problem is confined to my personal home network. I have removed and reinstalled my router, and the network adapters drivers etc. I have uninstalled my Norton Firewall and and disabled my Windows firewall to no avail. I have removed my WEP security features and tried to run it open with no improvement. I have connected the external network adapters on a neighbours computer running XP to see if I could connect to my home network. That didn't work as well. Bottom line is I simply cannot get an external wireless network adapter to work with my router. Yet my internal netbook adapter connects with no problems at all.
Today, I managed to redecorate my bedroom; where my computer sat on top of a shaky, wooden desk. That desk is now gone, caput, and replaced by a much bigger, sturdier and prettier glass replacement.Before I dissasembled the computer to re-decorate, I was able to browse the internet at ease. There were no problems at all...However, after the new desk was setup - and all wires replaced in their correct slots, I find that I am unable to connect to the internet, or even the house's network! For the past year, I have been wired to the router using a RTL8168C(P)/8111C(P) Family PCI-E Gigabit Ethernet NIC. It was plugged into an extension cord, in my room, into the Ethernet port in the back of my computer. Downstairs, it's twin was situated no less than 2 feet away from the router - plugged into the first port.Now, when I boot up the computer, the network notification presents the following message: "Unidentified Network. No network access", and sometimes presents a yellow ! next to it. So, I am reduced to typing on my mother's laptop - which has no problems connecting to the network.I am able to use the ipconfig /release command, but unable to use the /renew - it hangs in the command prompt, then tells me that the DHCP server cannot be located. The IP, beforehand, was reverted to 169.254.223.117 - before all of this, I was 192.168.0.5?
I am having a hard time configuring my Access point. I have a DSL Router connected to our telephone line and it works fine wirelessly, Yesterday I purchased TP LINK Router to configure as Access Point to extend wireless signal up to the second floor. Now, I am wondering, should I do some re-configuration on my DSL Router before configuring my TP Link Router? Guys, Please share your thoughts and if you have knowledge on how to configure my 2nd Router to my WifiNOTE: I followed the user guide manual that came with my TP LINK router but it is no USE. I just need to know if should I reconfigure my 1st Router in order to communicate with my 2nd Router.
For some reason my router and modem will not show correctly on my dell inspirion one desktop. Im running windows 7 and here are the net work connection deatils
Connection -specific DNS Belkin Description Realtek PCIe GBE Family Controller Physical Address 00-00-00-00-00-00 DCHP Enabled Yes Ipv4 Address 192.168.2.2 Ipv4 Subnet Mask 255.255.255.0 Lease obtained Wednesday, November 10, 2010 9:45 PM Lease Expires Sunday, December 18, 2146 4:17 AM IPv4 Default Gateway 192.168.2.1 Ipv4 DHCP Server 192.168.2.1 Ipv4 DNS Server 192.168.2.1 IPv4 WINS Server NetBIOS over Tcpip enabled Yes
The Connection was working about ten days ago and then suddenly stopped and read as an unidentified network no internet access. at one point is was not receiving packets but now it is but it still says no internet access on the IPv4 Connectivity. Media state is also enabled and the speed is 100.0 Mbps when i troubleshoot it says windows cant identify problem but in the details it says default gateway is available. when i use the cmd prompt ipconfig/all my local ethernet adapter has a physical address of all zeros.
At the moment I'm using Netgear AV200 powerline adapters and need to add 2 more adapters to my setup.Do I have to stick with Netgear or can I use another brand if they are both compliant with HomePlug AV1 standard and the same speed (200Mbps)Edit: Well apparently all powerline adapters are compatible as long as they are the same type (i.e. Homeplug AV or DS2), so I'll be getting more affordable pair of adapters...
We have just purchased a new computer with Windows 7 at our office and we were told there weren't any wireless network adapters that were compatible yet for 7. All of the other computers are Windows Vista and they have Ativa Wireless Network Adapters that work fine. It will not work with this new computer. Any suggestions of how to get up and running on the Internet?
I am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all. Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box.
When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".
My problem is that i bought some 1gb belkin powerline adapters to give me a better connection in my house than my wireless previously did. However i plugged them in and boom "Unidentified Network - No internet access".Now at first i thought it was because i had them plugging in through and extension lead downstairs so i removed all than and plugged them straight into the wall. This didnt help at all.I read some forums about turning of IPV6 cos apparently.
I have several VPNs and Virtualizing software installed, and they have this virtual network adapters in the network and sharing centre. In the "connect to a network menu", one shows working internet connection, while the other one shows no internet access, How do I get rid of those entries? I dont mind messing with the registry or the system files.
Whenever I boot up or disable/enable a network adapter it takes 1-3 minutes before I actually connect. After waiting, I'll see the little round circle spinning in the system tray and then i'm able to connect.While waiting for my adapter to work I noticed under tcp/ip settings that my gateway field is blank. If I put it in and go back, it's still blank. When the adapter finally connects it then shows up in the gateway field.Tried uninstalling AV, different drivers for LAN and wireless and reloading OS.
I have this device "WAN Miniport (IKEv2)" under Network Adapters and it's always listed as not working. I disabled it a long time ago but it always comes up as an error when I scan my computer. It won't update the driver, Windows always says that there was an error, and as far as I can see it doesn't do anything but it won't let me remove it even though it isn't working.
Win7 64 bit reports a problem with the driver for Microsoft ISATAP Adapter and Toredo Tunneling Adapter. Troubleshooting does not automatically fix it and reports that the drivers are OK. I have seen several other reports of this problem but not yet found a cause or fix
Upgraded to windows 7 ultimate 64bit from vista ultimate 64 bit. That didnt fix it. I'm desparate. I've tried everything I can find. It has a realtek 8169 nic on board sabertooth x85. I tried USB adapter and where it normally loads it just says it's installed but shows up in device manager. Like thw tealtek nic with yellow triangle on it. If I try an update driver it returns "parameter is incorrect" message. Its not connected and the is no IP using ipconfig. I Lost all my software CDs and emails with serials etc in a house fire last year.
I have over 50 virtual networking adapters in device manager, I have posted this question in many forums, and still cannot get rid of these pesky unused extra adapters. I know they have been created by using Virtualbox, and by creating many virtual machines and updating virtualbox. Unfortunately, I have tried uninstalling virtualbox and the drivers all remain in devicemanager. DeviceMgmt also does not allow me to uninstall or delete the adapters, (When I do they just stay there, even after rebooting.)I most likely have to go into the registry and delete them, but they are in so many different places there, I need to know the correct place to delete them. I have a bet that this is the forum where I will get the answer for this even though I have posted in virtualbox forums, technet, MSDN, superuser, serverfault, and stackoverflow.
Anyways my problem is that my vaio is running Windows 7 64bit and suddenly one morning NONE of the network adapters were working. No WiFi, no ethernet, no nothing. I figured something just happened to the drivers (happened before) so i'd just reinstall them...except this time I'm hit with:
Code :This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
I have tried everything short of a full restore. I tried downloading the drivers straight from Sony, just the driver files for Atheros, I can't do a restore point since I don't have any from before the problem. I have searched everywhere for a working solution but haven't found anything yet. I would like to avoid sending it in.....it's still under warranty but I don't have a Sony store near me and I'm gonna be going out of town in a couple weeks..
How do you download legacy hardware i need to install network adapters ISATAP and teredo tunneling and 6to4 adapters cause its giving me a code 10 error
My Network Adapters has suddenly disappeared after a Critical update by Windows update, now my network is X'ed out. I already did reformat and still nothing and in the past all I do is to System restore but after a while it had errors and I was forced to reformat but after that there's still no connection.
In Windows Home Premium 64bit we encounter this problem on a machine after trying to uninstall a norton product manually.The norton software led to serious problems of randomly emerging BSODs.As system uninstall did not work we researched a tutorial on how to manually uninstall the soft.t can be found here Enterprise Support - Symantec Corp. - How to manually uninstall the Symantec Endpoint Protection client from Windows Vista, Windows 7, and Windows 2008 R2 64-bitEverything worked smoothly until the last three steps of the routine failed (12.-14We can not uninstall/delete the wireless network adapters as described. After clicking "uninstall" there is the window that asks for confirmation (to uninstall) but after clicking "yes" the device manager window simply refreshes - and the device remains unchanged.
The comp started BSOD'ing out of nowhere, a new adapter I think called ISATAP or something like that shows up under network adapters in device manager which had a yellow exclamation icon. (Code: 31). Disabling or uninstalling its drivers resulted in BSOD's. Googled around and found the only way to fix it was to delete some registry entries, so without backing up the registry I deleted some keys. I don't remember which keys but the image above is the result. I got Ubuntu live booted up and using it to post this because my Win 7 installation obviously can't connect to the Internet.
*I tried reinstalling drivers (Marvel Yukon & Belkin), disabling and enabling stuff but nothing seems to be happening.
*Got some registry fixing tools or whatever, still the same.
I recently uninstalled all of my wireless network devices, these were a simple Wireless Card which was in a PCI slot and a wireless USB adapter, I uninstalled them from the device manager, and now under "Network Devices" I have about 32 'Microsoft 6to4 adapters' all with the yellow triangle on them, and then also there are 2 Microsoft ISATAP adapters, again with the yellow triangles. also, when I click on them, they say "This device cannot be started (error code:10)"And also now, my fast ethernet port has a yellow triangle on it too, but windows cannot find a driver.
I have a brand new acer aspire notebook and I'm trying to connect to my airport extreme card built into my iMac desktop. The laptop sees the signal just fine, but it will not connect to the Internet and I get "limited access". What can I do to connect?
I have a little problem with installing my new router. There were quite a lot of problems with the old smc, so I've bought a TP-Link router. I installed it just alright, it said congratulations, you have internet. I don't have though, not even on the directly plugged computer. It's kind of frustrating, since the old router is still working like before. So I plugged an ethernet cable from the old router's lan to the tp-link wan and with that, the new network is working just fine. The problem with the internet access occurs only, if the router is directly plugged to the modem. (The computers do find the network but the connection is kind of offline.) I don't really know what could be the problem, since I'm a little new to routers. I've read almost everything in the new router's manual and I'm pretty sure it's installed correctly. (ISP username and password copied from the old settings, mac address copied, all ip addresses pinged, done power cycle etc..) I also tried all of this on two different computers, in case eset is in some magical way blocking the router. Turned out this wasn't the problem. Well, I may have overlooked something though. I thought about resetting the modem, but I'm a bit afraid of losing the old router's internet connection as well.
I have 2 laptops - both run Windows 7 x64. Different brands (Asus G73 and Alienware M11x) with different network cards. I have found that neither will access the guest accounts on 3 different routers, all different locations and different brands. Tried latest versions of both IE and Firefox... no go. The tab shows the page is starting to load, where you enter the guest passwords, but the page never loads. It just times out.
I can get into the main admin accounts just fine, but ever the gust accounts. I show a connection via the network icon in the taskbar....then the yellow exclamation shows up. I get the popup that states 'More information is needed to log on - click here to open your browser'. But when I click on that, the browser opens but the page never does. I've set the default browser to both IE and FF... tried opening them via the click and via start button... both 32 and 64 versions...
Is this a Windows 7 x64 thing, as that seems to be the only constant between the two machines...?
I have just received a new window 7 pro computer. I have a net gear 3400 router. When i run the setup cd it tells me router is unresponsive. I put in 192.168.1.1. In URL it hangs I can access some sites except www.microsoft. com and Allentown, Lehigh Valley news from The Morning Call and mcall.com - mcall.com are just two. Router has been reset numerous times and has latest firmware. I was on the phone with net gear for five hours . I can ping router ok. I move it to my old xp machine everything works great. This all through wired connection. Have changed all cables. Bybass router all is ok
I reinstalled windows 7 home premium on my notebook, and downloaded the NIC & other necessary drivers from the manufacturer's website. I have no other software on the N/B. When I connect the LAN cable I can successfully ping my router, but not www.google.com. I can see the other PC's on the network. The icon on the bottom right shows a yellow triangle and I have no internet access. I have an automatic IP & DNS server set in the IPv4 & v6. I have a desktop PC running Windows 7 on the network that connects to the internet with the router.
I can't understand how a newly formatted PC struggles to connect to the internet (via LAN), when my username & password is already setup on my router.
Details of notebook: Packard Bell, i5 430M, 4GB RAM, 640GB HDD, ATi Radeon HD5650 VGA, W7HP 64 Windows IP Configuration Ethernet adapter Local Area Connection:
I am on a cabled LAN network with internet access. I can also access the internet through a different wireless router. When I am connected to the LAN by internet access is also through it. I would like to stay connected to the LAN network but at the same time have the internet access through the wireless. Is there a way to set this up?