Unidentified Network When Using Powerline Adapters

Dec 27, 2010

My problem is that i bought some 1gb belkin powerline adapters to give me a better connection in my house than my wireless previously did. However i plugged them in and boom "Unidentified Network - No internet access".Now at first i thought it was because i had them plugging in through and extension lead downstairs so i removed all than and plugged them straight into the wall. This didnt help at all.I read some forums about turning of IPV6 cos apparently.

View 9 Replies


ADVERTISEMENT

Unidentified Network; No Network Access - Powerline Adapters

Dec 1, 2011

Today, I managed to redecorate my bedroom; where my computer sat on top of a shaky, wooden desk. That desk is now gone, caput, and replaced by a much bigger, sturdier and prettier glass replacement.Before I dissasembled the computer to re-decorate, I was able to browse the internet at ease. There were no problems at all...However, after the new desk was setup - and all wires replaced in their correct slots, I find that I am unable to connect to the internet, or even the house's network! For the past year, I have been wired to the router using a RTL8168C(P)/8111C(P) Family PCI-E Gigabit Ethernet NIC. It was plugged into an extension cord, in my room, into the Ethernet port in the back of my computer. Downstairs, it's twin was situated no less than 2 feet away from the router - plugged into the first port.Now, when I boot up the computer, the network notification presents the following message: "Unidentified Network. No network access", and sometimes presents a yellow ! next to it. So, I am reduced to typing on my mother's laptop - which has no problems connecting to the network.I am able to use the ipconfig /release command, but unable to use the /renew - it hangs in the command prompt, then tells me that the DHCP server cannot be located. The IP, beforehand, was reverted to 169.254.223.117 - before all of this, I was 192.168.0.5?

View 2 Replies View Related

Use Different Powerline Adapters On Same Network?

Jul 21, 2011

At the moment I'm using Netgear AV200 powerline adapters and need to add 2 more adapters to my setup.Do I have to stick with Netgear or can I use another brand if they are both compliant with HomePlug AV1 standard and the same speed (200Mbps)Edit: Well apparently all powerline adapters are compatible as long as they are the same type (i.e. Homeplug AV or DS2), so I'll be getting more affordable pair of adapters...

View 1 Replies View Related

Any Compatible Network Adapters ?

Dec 30, 2009

We have just purchased a new computer with Windows 7 at our office and we were told there weren't any wireless network adapters that were compatible yet for 7. All of the other computers are Windows Vista and they have Ativa Wireless Network Adapters that work fine. It will not work with this new computer. Any suggestions of how to get up and running on the Internet?

View 5 Replies View Related

Network Constantly Changing Between Unidentified Public Network And Home

Aug 30, 2012

Home network with Wifi and ethernet. Using 3x Notebooks and 3x workstations. One of the workstations (W7 ultimate) keeps changing between Public and Home. When this happens, the internet connection dies. I cannot see other workstations either when on public network. Workstation using wifi. Does the same on cable. When it changes to Public, it disconnects from the internet and I cannot get to the router even though it has the workstation has an IP(DHCP or static). Default gateway and subnet is correct. TCP v4 is being used and nothing else is enabled.

Why is this happening?
- I have tried DHCP as well as Static addresses
- Reconfigured NIC(Netgear WG311T), uninstalled and reinstalled it.
- Removed Wifi connection and re-added it.
- Changed auth type, encryption type and keys to connection

Have I covered everything? The only thing different is that I installed a new router - Duo Plus 300wr. It cannot be the router because all the other notebooks connect to it wireless and so does my iPad, Android device and tablet...so it rules that out?

View 3 Replies View Related

Network Adapters Not Working In Windows 7

Jul 27, 2011

I am having problems with any type of Network Card or Network USB adapter working with my PC running Windows 7. I had a LinkSys WMP54G PCI card working on this computer about a year ago as I was needing to use a wireless connection but then I didn't use it for 6 months. When I went to use it again, it wouldn't pick up connections at all. Thinking it was an issue with the card, I picked up a Edimax 7612UAn USB adapter thinking it should work out of the box.

When I plug the USB adapter in, the standard Windows driver installation tries to run but an error message occurs stating "Device driver software was not successfully installed" accompanied by "Realtek RTL8191SU Wireless LAN 802.11n USB Failed". If I try to install the drivers manually, nothing changes and in Device Manager the following error message is displayed under Device Status "This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)".

View 3 Replies View Related

How To Hide VPN / Virtual Network Adapters

Aug 18, 2012

I have several VPNs and Virtualizing software installed, and they have this virtual network adapters in the network and sharing centre. In the "connect to a network menu", one shows working internet connection, while the other one shows no internet access, How do I get rid of those entries? I dont mind messing with the registry or the system files.

View 2 Replies View Related

Slow Network Startup On All Adapters

Apr 22, 2010

Whenever I boot up or disable/enable a network adapter it takes 1-3 minutes before I actually connect. After waiting, I'll see the little round circle spinning in the system tray and then i'm able to connect.While waiting for my adapter to work I noticed under tcp/ip settings that my gateway field is blank. If I put it in and go back, it's still blank. When the adapter finally connects it then shows up in the gateway field.Tried uninstalling AV, different drivers for LAN and wireless and reloading OS.

View 7 Replies View Related

Download Network Adapters For Windows 7?

Nov 24, 2012

miniport network adaptor

View 2 Replies View Related

Drivers And Network Adapters Hp Windows 7 32?

Feb 18, 2013

where and how do I get drivers and network adapters for hpg6 without installing into my friends computer

View 1 Replies View Related

WAN Miniport (IKEv2) Listed Under Network Adapters

Dec 27, 2011

I have this device "WAN Miniport (IKEv2)" under Network Adapters and it's always listed as not working. I disabled it a long time ago but it always comes up as an error when I scan my computer. It won't update the driver, Windows always says that there was an error, and as far as I can see it doesn't do anything but it won't let me remove it even though it isn't working.

View 8 Replies View Related

Windows 7 Network Adapters Error Code 10?

Dec 20, 2010

Win7 64 bit reports a problem with the driver for Microsoft ISATAP Adapter and Toredo Tunneling Adapter. Troubleshooting does not automatically fix it and reports that the drivers are OK. I have seen several other reports of this problem but not yet found a cause or fix

View 6 Replies View Related

Network Adapters Won't Install - Parameter Is Incorrect

Mar 30, 2012

Upgraded to windows 7 ultimate 64bit from vista ultimate 64 bit. That didnt fix it. I'm desparate. I've tried everything I can find. It has a realtek 8169 nic on board sabertooth x85. I tried USB adapter and where it normally loads it just says it's installed but shows up in device manager. Like thw tealtek nic with yellow triangle on it. If I try an update driver it returns "parameter is incorrect" message. Its not connected and the is no IP using ipconfig. I Lost all my software CDs and emails with serials etc in a house fire last year.

View 6 Replies View Related

Cannot Access Router With External Network Adapters

May 31, 2011

I am running Windows 7 Home Premium (64 bit) on a Dell Inspiron 560. I am using a DI-524 D-Link wireless router. I have an Acer Aspire One Net Book running Windows XP Home it is equipped with an internal wireless network adapter. I can connect/communicate with router and access the internet with no problems whatever. However, when I connect an external wireless network adapter e.g. Alpha AWUS036H I cannot get a connection when I disable my internal network adapter. I have also tried the Trendnet TEW-424UB USB external wireless network adapter and the symptoms are exactly the same. If I leave home and use another Wireless point of access I have no trouble connecting using the external adapters which means the problem is confined to my personal home network. I have removed and reinstalled my router, and the network adapters drivers etc. I have uninstalled my Norton Firewall and and disabled my Windows firewall to no avail. I have removed my WEP security features and tried to run it open with no improvement. I have connected the external network adapters on a neighbours computer running XP to see if I could connect to my home network. That didn't work as well. Bottom line is I simply cannot get an external wireless network adapter to work with my router. Yet my internal netbook adapter connects with no problems at all.

View 2 Replies View Related

Delete Many Duplicate Virtual Network Adapters?

Sep 9, 2012

I have over 50 virtual networking adapters in device manager, I have posted this question in many forums, and still cannot get rid of these pesky unused extra adapters. I know they have been created by using Virtualbox, and by creating many virtual machines and updating virtualbox. Unfortunately, I have tried uninstalling virtualbox and the drivers all remain in devicemanager. DeviceMgmt also does not allow me to uninstall or delete the adapters, (When I do they just stay there, even after rebooting.)I most likely have to go into the registry and delete them, but they are in so many different places there, I need to know the correct place to delete them. I have a bet that this is the forum where I will get the answer for this even though I have posted in virtualbox forums, technet, MSDN, superuser, serverfault, and stackoverflow.

View 7 Replies View Related

Windows 7 Won't Load Drivers For Network Adapters

May 30, 2012

Anyways my problem is that my vaio is running Windows 7 64bit and suddenly one morning NONE of the network adapters were working. No WiFi, no ethernet, no nothing. I figured something just happened to the drivers (happened before) so i'd just reinstall them...except this time I'm hit with:

Code :This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

I have tried everything short of a full restore. I tried downloading the drivers straight from Sony, just the driver files for Atheros, I can't do a restore point since I don't have any from before the problem. I have searched everywhere for a working solution but haven't found anything yet. I would like to avoid sending it in.....it's still under warranty but I don't have a Sony store near me and I'm gonna be going out of town in a couple weeks..

View 6 Replies View Related

Ralink Based Belkin Network Adapters - Install

Apr 9, 2010

How to Install Ralink based Belkin Network Adapters ?

View 0 Replies View Related

How To Download Legacy Hardware Need To Install Network Adapters

Mar 23, 2012

How do you download legacy hardware i need to install network adapters ISATAP and teredo tunneling and 6to4 adapters cause its giving me a code 10 error

View 1 Replies View Related

Wireless Connection Network Says It Is An Unidentified Network?

May 12, 2011

Recently when I try and connect to the internet my wireless connection network says it is an unidentified network with no internet access. This never happened before.

View 2 Replies View Related

Unidentified Network - Cannot Change It To HOME NETWORK

Oct 22, 2009

Okay so I've installed windows and everything is working okay except i can't connect my laptop to my computer via LAN because it won't let me change it to a HOME NETWORK. It is just gets set to an unidentified Network. any possible suggestions?

Also I've look at removing this from the services but its not running it when i go under task manager, unless it somewhere else.

"##Id_String2.6844F930_1628_4223_B5CC_5BB94B87 9762 ##"

View 1 Replies View Related

Network Adapters Not Appearing In Device Manager After Critical Updates?

Jul 17, 2012

My Network Adapters has suddenly disappeared after a Critical update by Windows update, now my network is X'ed out. I already did reformat and still nothing and in the past all I do is to System restore but after a while it had errors and I was forced to reformat but after that there's still no connection.

View 5 Replies View Related

Unable To Uninstall Wireless Network Adapters From Device Manager?

Jun 18, 2012

In Windows Home Premium 64bit we encounter this problem on a machine after trying to uninstall a norton product manually.The norton software led to serious problems of randomly emerging BSODs.As system uninstall did not work we researched a tutorial on how to manually uninstall the soft.t can be found here Enterprise Support - Symantec Corp. - How to manually uninstall the Symantec Endpoint Protection client from Windows Vista, Windows 7, and Windows 2008 R2 64-bitEverything worked smoothly until the last three steps of the routine failed (12.-14We can not uninstall/delete the wireless network adapters as described. After clicking "uninstall" there is the window that asks for confirmation (to uninstall) but after clicking "yes" the device manager window simply refreshes - and the device remains unchanged.

View 4 Replies View Related

Deleted Registry Entry To Fix Code 31 / Network Adapters Won't Work

Jan 12, 2013

The comp started BSOD'ing out of nowhere, a new adapter I think called ISATAP or something like that shows up under network adapters in device manager which had a yellow exclamation icon. (Code: 31). Disabling or uninstalling its drivers resulted in BSOD's. Googled around and found the only way to fix it was to delete some registry entries, so without backing up the registry I deleted some keys. I don't remember which keys but the image above is the result. I got Ubuntu live booted up and using it to post this because my Win 7 installation obviously can't connect to the Internet.

*I tried reinstalling drivers (Marvel Yukon & Belkin), disabling and enabling stuff but nothing seems to be happening.

*Got some registry fixing tools or whatever, still the same.

View 6 Replies View Related

Unidentified Network

Sep 6, 2009

I just moved to a new home, and i cannot connect to my local LAN ! I am on a Mac right now ( arghh ) and the Internet works fine on this one.

I am using a cable to a router, wich is connected to a modem. The router is fairly old but has always worked fine ( using a direct cable doesnt work aswell ). Windows 7 says it is connected to a 'Unidentified Network'. The ipv4 settings for the adapter are; Automatic ip/dhcp.

ipconfig gives an ipv6 address. The automatically generated ip is: 169.254.241.20. There is nothing at Default Gateway. The driver settings are correct, as far as i believe. I downloaded the latest x64 Windows 7 marvell yukon drivers.

I disabled sleep mode on my pc. I don't have the Bonjour service running. On the Mac, i only had to enable DHCP and it recognized the network correctly. These are the ip's that it got:

ip: 83.87.107.135

subnet: 255.255.248.0

router: 83.87.104.1

This is getting frustrating since i cannot see where the problem could be.

here are my specs;

Asus p5w DH Deluxe

win 7 ( 7600 )

q6600

2 integrated network adapters on the mobo: Marvell Yukon 88E8053 pci-e Gigabit Ethernet Controller

View 7 Replies View Related

Microsoft 6 To 4 Adapters & ISATAP Adapters?

Jun 24, 2011

I recently uninstalled all of my wireless network devices, these were a simple Wireless Card which was in a PCI slot and a wireless USB adapter, I uninstalled them from the device manager, and now under "Network Devices" I have about 32 'Microsoft 6to4 adapters' all with the yellow triangle on them, and then also there are 2 Microsoft ISATAP adapters, again with the yellow triangles. also, when I click on them, they say "This device cannot be started (error code:10)"And also now, my fast ethernet port has a yellow triangle on it too, but windows cannot find a driver.

View 1 Replies View Related

Unidentified Network No Network Access

Jul 18, 2012

I have 2 different laptops. both running Windows7 and connecting to the internet wirelessly. within a few days of each other they both began to display "Currently connected to: Unidentified network No network access" and they will not let me get on the internet. It is not my router becuase It shows the same thing no matter where I try to connect. I have tried my gym and a local restaurant that I have always had success connecting to before. Furthermore my WindowsXP desktop is directly connected and is connecting to the internet without any problems. My laptops are both running AVG for antivirus.

View 4 Replies View Related

Unidentified Network - No Network Access

Apr 8, 2011

my laptop doesn't connect to my wireless network, neither by cable (wired).

View 9 Replies View Related

Unidentified Network - No Network Access

Dec 31, 2011

Yesterday it worked and when I booted today it didn't I have absolutely no idea what the problem is and I have checked everything I know with no use.

- I am using d-Lan (PowerLan) and have had no problems with it until today.

- My router, modem and the d-lan devices are functioning properly which I have tested multiple times so I'm sure the problem lies with my computer.

- I have tried Troubleshooting with no effect

- It isn't an IP conflict

- It isn't a 3rd party program (I started it in safe mode, same problem)

- Internet still works over my W-Lan but is incredibly slow and unstable

View 6 Replies View Related

Unidentified Network - No Network Access

Dec 26, 2009

For boxing day, I bought myself a new Computer case, a Cooler Master HAF 932. After setting it up and booting my computer, without any problems, my Internet would not work.

I attached the Network & Sharing Centre screen to show you what it says. I've tried many things, switching cables, direct input from modem (I use a router), and all sorts of guides that have similar problems.

View 9 Replies View Related

Unidentified Network In Windows 7?

Mar 7, 2011

I have got a desktop computer and a laptop at my home. I have got a single internet connection. So I added an extra NIC card to my desktop PC. Then I connected my desktop to the internet and then connected my laptop and desktop using a crossover network cable. Both my machines have got win 7 installed. So when I created the network my laptop identified the network and allowed it to me to choose between home, work and public networks. I am able to share the internet too. But my desktop keeps on saying unidentified network which prevents me from joining my home-group.

View 2 Replies View Related

Cant Change Unidentified Network

Jul 27, 2009

Ive just installed Windows 7 7600 HP on to one of our work PC's and it says its connected to an unidentified network. I cant change it to work network or even Home network but the strange thing is its working fine. All our other PC's can see it and share files on it etc and i have internet access on it.

This is the second time ive installed HP and the second time this has happened. In the past ive been using Ultimate and this didn't happen.

We use static IP addresses for our internal network with no DNS server.

Anyone got any ideas how i can change this network location. Im using HP as im testing it out for when my copy arrives in Oct but if this is a problem related to HP i might think again.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved