I did a clean install of Windows 7 ultimate 32-bit on my laptop. It booted well and I thought of changing the harddrive letters. After shutdown the laptop could not load windows again. Going through the process to revive it I found out that the harddrive order changed making the back up drive to be drive C:. I am now stuck and cannot find a way around this.
View 9 Replies1. i had a problem with google that redirected me to advertisements whenever I searched.
2. i booted the computer into safe mode and ran malwarebytes and bitdefender to scan my computer and i just let the programs do their thing.
3. upon restarting my computer after the scan my laptop was stuck in a continuous loop.
4. i tried every setting after pressing f8 such as safe mode, safe mode with networking, etc. and everytime i can't get past the boot up.
5. finally i try "disable automatic restart on system failure" and then it leads me to the BSOD and it says
STOP: c0000135 The program can't start because %hs is missing from your computer. Try reinstalling the program to fix this problem I saw several posts about this but a few of the answers scared me by saying something to the effect of "this will only work with this user, don't try it with your computer" Just to reiterate i can't even get into safe mode and so have no clue how i'm going to follow your procedures. i also misplaced all discs that my laptop came with edit. I have a Dell Inspiron N5010?
My windows 7 toshiba laptop wont get past a screen that says
Intel UNDI, PXE-2.1 (build 082)
Copyright (C) 1997-2000 Intel Corporation
For Realtek RTL8101E/8102E PCI-E Ethernet Controller v1.07 (080320)
PXE-E61:Media test failure,check cable
PXE-M0F:Exiting PXE ROM.
No bootable device--insert boot disk and press any key"
The problem is I dont have a boot disk and i cant get past this screen. P.S. it happens when i turn it on, it goes to a black screen saying that.
i just bought an asus u31s laptop a couple of weeks ago for school and all was great until today. it suddenly crashed and gave bsod. i was just on Internet or something, nothing special, but it had been running for a few hours. so now it won't boot up, it simply reboots constantly. i can't even get into safe mode. bios i can get into, but i'm unable to do anything, since it appears to freeze, when i get in there.
View 9 Replies View RelatedI've seen many different discussions about this but they don't have the same problem I have.but in the recovery disk but this is what it says
Problem Event Name:StartupRepairOffline
Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown
Problem Signature 04: -1
Problem Signature 05: ExternalMedia Problem Signature 06: 1 Problem Signature 07: NoOsInstalled
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
I have a Lenovo ThinkPad X60 laptop with Win7 32-bit Ultimate and an SSD (I know, I know, just go with it. I'm building a desktop soon). I could list the specs, but that's useless for this problem (I'd think).
At times (not always), when either resuming from hibernate or booting up from a shut down, the computer generally freezes at the point right after the BIOS screen. So it's just a black screen. This is before the window that says "starting up" (literally a window... the Windows logo). Whenever it freezes, it NEVER goes to the boot screen of Windows. I'm assuming this is an error with the hard drive, since the OS is on the SSD and the boot screen is from the mobo. However, this only started happening after a rather heavy fall to the ground that cracked many parts of the plastic shell on the computer. It still works occasionally when I can get it to boot up (nothing different when it boots up... same settings and everything. Spontaneous).
I have tried:
1) Cold reboot
2) Removing battery
3) Going off only battery
4) Unplugging EVERYTHING from the computer
I have not tried chkdsk yet. Is it necessary? Also, would there be a log somewhere of what happened? It never booted into Windows.
My HTPC runs win7 32bit.
For whatever reason, it now fails to work. The boot works fine. It then logs me in automatically, I get either the welcome screen or the desktop, then the cursor hang still, the disk stops churning, and the windows is frozen solid. It does not respond to any key combination familiar with, nor to the mouse.
I ran the rescue disk boot troubleshooter, but that's for early stage problems. I used msconfig to disable all startup programs, ran combofix, lookes at ntbtlog.txt, moved to the previous automatic recovery point, still the same issue.
I'd rather not format and reinstall. I'm desperately looking for ways to save it.
I am trying to dual boot Windows 7 Home Premium and Ubuntu 10.04 on my laptop (Toshiba Portege M400). I had Ubuntu 10.04 installed previously but I decided to wipe my hard drive before installing Windows 7. I used GParted to delete all my partition and setup two new ones. I formated the first partition as NFTS for Windows. After that, I proceeded to installing Windows. The first time I tried it, I was successful although I did need to reformat that NFTS partition I had made because it said that the partition table type (GUID) was not compatible. Windows 7 installed fine after that. However, when I try to install Ubuntu, it sees the whole disk as blank. I tried resolving this issue with GParted but that too saw the drive as if it were blank even though Windows 7 was installed. After that, I booted up the GParted Live CD once again and changed the partition table to MS-DOS. My Windows 7 boots up and goes through all the tasks before the first boot up. When it restarts for the first time, it fails to boot; it simply stays on the glowing Windows logo. I've tried formatting the entire disk through the Windows 7 disk and partitioning from there several times and I still get the same results.
View 3 Replies View RelatedI have just built a computer Win7, Intel corei5, 4G memory, and the computer just turns on then turns off. It doesnt even get to a screen to run settup.
View 1 Replies View RelatedI have a windows 7 pro 64 bit HP desktop computer that will not load windows. I have tried safemode, safemode w/ networking, and last know good config. I've run startup repair both from windowsRE and an original windows 7 pro disk. I have attempted multiple system restores (non destructive) to a number of different dates. The system restores say that they work but the machine still loops.
I know it's just some small windows corruption. I would have no trouble backing up my files with a linux distribution live flash drive and restoring the OS but I REALLY don't want to do that. How can I identify and repair the problem without starting from scratch. I'm familiar with msdos cli, but don't know which commands (if any) will help. I also don't know of any live CD's/ tools that will allow me to fix this problem. My problem here is simply lack of information.
I was watching a football game on firstrowsport.eu and my computer (a hp pavilion desktop) just shut down uncommanded. I waited for it to restart, and after the BIOS screen, it just had a flashing cursor. I used the disc version of PartedMagic to get into my computer and ran the fdisk-l command. [code]
View 10 Replies View RelatedWhen Win 7 pro (32 bits) boots up, as we all notice, there is a second or so when there is a black screen, w/ just your mouse cursor, and then you are supposed to see the blue Welcome screen.
In the past 2 months, my computer is stuck at that black screen about 7 times, as recent as tonight. I've done a clean install w/ the latest Nvidia driver 2 weeks ago. No change. It looks like win 7 Pro is stuck there and waiting for something as my hard drive light blink on and off.
So, I would do nothing, or sometimes I would disconnect the HDMI port connects to my 3rd PC Panel (see below), and I would wait for 5 min. or so. Then my login logo shows up, I click it, and I got to windows.
Now, w/ the normal boot up, I don't have that login logo, win 7 pro will simply boot up directly to win 7 main screen after I turn on the computer.
Some1 said this could be IRQ sensing problem of the video card. But so far, I have no proof on that 1 way or the other: All these started about 2 months ago, at or near the same time when the Sharp LED TV technician came to my house and upgraded all the firmware, including the firmware that consumers can't download, to my Sharp LED LCD TV, as the power button wasn't working.
Then in the past 2 mth., every time I turned on my LCD TV, which is connected to my computer as the 3rd screen via a DVI to HDMI cable, Win 7 senses this 3rd panel, and the screen went black and back on again. This isn't the way it used to be: as it WAS NOT SWITCH TO THE HDMI PC PORT.
My Sharp LCD has 4 HDMI output. Tonight for e.g., I was on Input 2, which is satellite, but as soon as I turn on the Sharp LCD, win 7 senses this 3rd screen, and the screen do that black screen then back on again w/ the music charm note.
This was not the way it used to be, in the past yr., w/ this same set up, win 7 only went to the black screen and back on when I switch to Input 1, which is PC at 1920x1080. And I don't know if the above is related to the boot up lock up or not.
I found another old hard drive, a Seagate 250 GB, and when I plug it to the pc, Windows is stuck at the Windows 7 logo at the boot, and the logo itself lags. the hard drive is detected in the BIOS. (can it be a virus on this old hard drive?)
View 9 Replies View RelatedI am trying to boot Win7 from my USB drive on my new SSD and I'm having a problem with it. It is loading Windows, but it loads the Setup screen and never loads the actual Setup itself. It's just my mouse, and it's not frozen. I have installed this Windows from the exact USB several times before, but not on this actual AMD chipset system. My computer is recognizing the new SSD as well, when I select boot order it shows up.
Is there special drivers, possibly, that I have to include on the USB now that I'm on an AMD chipset Mobo?
I built a new gaming PC about a month and a half ago and its been running fine up until now. I turned it on a couple of days ago and Win 7 was freezing up. The mouse cursor was a blue wheel and I couldn't click or do anything. I couldn't even access the command line and ctrl+alt+del didn't work either. At this point it did boot up in safe mode. I powered it down and now it won't boot past BIOS. I reseated everything and checked all the connections and everything seems good.
View 3 Replies View RelatedMy laptop decided not to start up today. It shut down last night normally, today it keeps getting stuck on "starting window". I tried safe mode, but it gets stuck at starting windows. I tried starting from disk, it says loading files then it goes start to the starting windows and gets stuck. I tried pressing f8 but there is no repair computer option. Did my ssd die?
View 5 Replies View RelatedI have a Levona G570 laptop. Windows is getting stuck on the welcome screen and also when I try booting in safe mode all I get is the safe mode in all 4 corners with a black screen, i can see the cursor also.
I tried doing a startup repair and the first couple times I tried would just keep going for over 5-6 hours, finally it did it again and gave me this error message along with it saying something along the lines of "Windows cannot automattically fix this"
Problem Signature
Problem Event Name" Startup Repair Offline
Problem Signature 01: 6.1.7600.16385
Problem Sig. 02: 6.1.7600.16385
Problem Sig. 03: Unknown
Problem Sig. 04: -1
Problem Sig. 05: System Disk
Problem Sig. 06: 1
Problem Sig. 07: No OS Installed
OS version: 6.1.7601.2.1.0.256.1
Local ID: 1033
Computer was working fine yesterday, shut it down then this happened out of nowhere? Laptop did not come with any Install Disc at all.
A Dell Inspiron E1705, w/ 2x2gb mem, 500 gb hd, ATI Radeon x1400 vid and Win 7.There were no Dell drivers or programs and the system BIOS was ver A01. Checking the Dell website against the Service Tag, I found 22 drivers and programs specific to the computer. Most of them ran and installed under Win 7 with no trouble. The last one was the bios flash utility program to update the bios to ver A10. The bios flashed, seemed to go ok. But on system reboot, after the initial screem about resetting the memory sticks, the computer is stuck in an infinite reboot loop.It loads the initial POST screen, completes the POST, seeks for its boot device and when it finds and starts to access the installed HD it reboots. I have reset all the bios settings to factory default settings. I have pulled the system battery and "cleared the cmos", but no joy there. I have created a bootable usb flash drive with another Dell laptop, and the computer will boot from that. I have other bootable cd's, and the computer will boot from them. I can use the bootable cd's to determine that the programs they run (freeware backup programs and a copy of bart pe) can access the installed hd,and see the files there, so the installed hd is intact. But i still can't get the computer to boot from it.My first thought was to reinstall the ver A01 bios, but it would not complete the process and remained at ver .A10. I was able to flash bios A09, and then A07, etc, all the way back to ver A04. But after that I could go back no further, A02 and A01 flash utilities returned an error message. If I found some compatible mem sticks and a smaller hd, installed them, could I reflash bios ver A02 or A01? Would that do me any good? (I have 2 x 256 mg mem sticks from a dell inspiron 5100 which I upgraded to 2x1gb, and a 40 gb 2.5in hd that also came out of the 5100, so I could use those parts in the e1705 to reflash the earlier bios)
View 7 Replies View Relatedi installed LibUSB-Win32- drivers so i could use iRecovery on my iPhone,on completion of installation of LibUSB my keyboard and mouse turned off, well all of my USB was disabled. so i was forced to restart, sadly same thing, login screen no keyboard or mouse, i tried in safemode, same thing. however my keyboard works in CMOS and BIOS so i know its a OS issue. and this only happened when i installled LIBUSB, i looked it up and tried manually removing LibUSB using the Win7 setup disks command prompt. i deleted LibUSB0.sys out of Windows/Systen32/Drivers so that LibUSB wont be called upon during start up, however doing this has now meant my PC will reboot after loading Windows even in safemode, the Starting Windows screen appears. fades and riight before it goes to the login screen it restarts, Safemode too. i have no Restore points and i cannot and i mean Cannot Format this harddisk, its not backed up and i have over 400GB of data i absolutely NEED.Im so stuck its not funny i have no idea what to do to get windows booting again and without this silly LibUSB stuff! i dont have aany PS./2 Ports on my mobo either!, what can i do >? Please ive asked everywhere and no one knows what i can do except reformat.
View 1 Replies View RelatedThe first problem was that it kept booting into the windows startup repair. For a split second i can see windows 7 loading but then it automatically went to the startup repair , after many many reboots i opened the command prompt in windows startup repair and tried fixing the master reboot.Now it gets stuck at loading operating system.Even when i try to boot from the windows 7 CD and Truecrypt rescue disk it still gets stuck at loading operating system.The whole harddrive was encrypted with truecrypt and it use to go to truecrypt bootloader after loading the operating system but it doesn't do that anymore.
Specs :
mobo : Gigabyte GA-890FXA-UD5
cpu: phenom ii x6 1090t
gpu : radeon hd 6950
hard drive : western digital black caviar 1TB
Last night, my computer spontaneously rebooted. When it got to the 'Starting Windows' screen, the animated windows logo never appeared. I rebooted. Tried running System Recovery. This time, the screen is "Windows is loading files..." The progress bar fills up and then freezes.
Tried booting into safe mode. Again, the "Windows is loading files" progress bar fills up and then freezes. Tried to reinstall Windows. Boots from DVD, then the "Windows is loading files" progress bar fills up and then freezes yet again. Have been running Memtest86+ for the last ~9 hours, no issues.
Specs: MSI 790FX-GD70 | AMD Phenom II X4 945 | 4x2GB G.Skill Ripjaws DDR3-1333 | 1x80GB Intel SSD (OS) | 2x1TB Samsung Spinpoint F3 7200RPM HDD (other) | 1x2TB WD Elements external HDD (backup) | XFX RadeonHD 6870 1GB GDDR5
I have windows 7 home premium 32 bit dell laptop. Lately, it takes more than 10 minutes before it boots before the windows logo appears). From there the computer works normally. I got a suggestion to check for malwares or viruses so that is what I did. I started by going to msconfig and edited the boot options to start automatically to safe mode with networking, then rebooted my system. After booting, it loaded up the initial screen of safe mode, but then it restarted by itself.
I am now stuck on this reboot loop going into safe mode, it won't even let me go back to normal mode. I went to startup repair, but it didn't find anything, so had to reboot again onto the same situation. I have searched for possible answers, and the best that I could get was to remove the safe boot options and go back to normal mode. The syntax to type was bcdedit /deletevalue {default} safe boot but it didn't work, same with bcdedit /deletevalue safe boot.
I am getting this : "An error occurred while attempting to delete the specified data element. Element not found."
my Dell Studio 1555 laptop will not boot either into regular windows or safe mode.When booting into safe mode, the very last file that will load is "CLASSPNP.SYS".When that happens it will stay stuck loading the next file for a few minutes, then restart itself into the Windows Error Recovery screen.When I try start-up repair, it goes to a blank black screen and repeats the procedure above (ie. it gets stuck and restarts a few minutes later) When I hard-shut down by pressing the power button, a BSoD appears for a fraction of a second right before it dies.What could the problem be, and what can I do to fix it? I have the windows 7 install disk, if needed. Should I go ahead and try an installation repair using the disk?
View 5 Replies View RelatedI've an hp mini 110 with windows seven starter and I want to make a dual boot 7/XP...I downloaded the 32bit version of the sp3 XP and following this guide: Dual Boot Installation with Windows 7 and XP I installed on a new partition...(I didn't put the sata drivers cause when I started the usb on the boot xp started to install without problem)..after xp finished I booted but I get this error "windows could not start because of a computer disk hardware configuration problem.."...when I only can see XP and It can't be opened...I tryed with the 7-system-recovery on the usb to make recovery and put these strings on prompt
bootrec /FixMbr
bootrec /FixBoot
bootrec /RebuildBcd
but nothing,same error!!!I thought it was a sata driver issue so I downloaded the drivers and opened on the system recovery through usb but it says they can't be installed....so should I slipstream in the xp iso before install xp??
i recently install new updates on my laptop , after downloading and installing and asking me to restart my computer ,i did choose to restart now . After booting up again it is now stuck on windows 7 logo screen on startup. I tried booting up on safe mode and last known good config. but it didn't work. Also tried to use windows installation disk but it doesn't work either it just keep loading on "setup is starting" also tried "repair my computer" option but it just show me just a plain black screen
i had a Toshiba satellite laptop l745d with a6 vision AMD graphic card,windows 7 ultimate x64 os , 4gb of ram quadcore
I dropped my laptop this weekend. But it still worked for a few minutes before it froze. So I powered it off and tried to turn it back on. It turns back on just fine, but will continuously load the "Starting Windows" screen. I tried doing diagnostics and repairs, nothing. When I load it in safe mode, it loads up until the ClassPNP.sys, and then freezes.
View 7 Replies View RelatedSo, I'm not exactly sure what I did. I was clearing up some space on my computer after using the Norton Removal Tool to get rid of this Norton trial popup that came up everytime I booted my computer. Now, after it told me to restart, it seems to be stuck in an endless boot cycle that resets itself after showing the Windows logo. I've since tried running startup repair, which freezes as it shows the progress bar for 'Windows is loading files'. Safe mode will not work, either. It just sends it back into the boot cycle. Not sure what to do at this point. My computer came pre-installed with Windows 7 Home Premium 64bit, so I don't have any startup discs.
View 3 Replies View RelatedWindows wont boot up I get stuck on the "starting windows screen" Startup Repair cannot repair this computer automatically:
Problem signature:
�Problem Event Name: StartupRepair Offline
�Problem Signature 01: 6.1.7600.16385
�Problem Signature 02: 6.1.7600.16385
�Problem Signature 03: unknown
�Problem Signature 04: 21200718
�Problem Signature 05: AutoFailover
�Problem Signature 06: 10
�Problem Signature 07: BadDriver
�OS Version: 6.1.7600.2.0.0.256.1
�Locale ID: 1033
This is an acer aspire laptop that is stuck in hibernation/sleep mode. It has windows 7, the power light blinks, no response whatsoever to windows key or any other keys including ctrl alt del. I have checked without memory and hard drive and have the same results. It will power off but will not get out of hibernation mode while it is turned on.
View 1 Replies View RelatedI bought a hp laptop about a year ago and have been having a problem for the last couple days. I have windows 7 and when I go to start the laptop up it shows the HP screen then goes to the windows screen like its loading but then goes back to the hp logo and is stuck. I ran a HDD test and memory test those came back good. I tried to go into safe mode it acts like it loading then shows a blank screen. I try to do a system recovery and system restore the screen stays blank. I also took the battery out and press the power button down but that hasn't work. It's no longer under warrenty.
View 3 Replies View RelatedMy system Quad Core 2.66 4 GM Memory, I TB Maxtor, MB 790i Ultra SLI, EVGA NVIDIA 280
I had the windows seven 7100 release but i bought the final version
when i did a clean install of windows seven you can see:
the system get stuck in the screen after the verifying dmi and look the dvds to boot and try to boot in the HD but you can see the system does not boot, after the dvd copy and expand the setup files and start the first screen to do the final installation.