Networking Computers With Vonage Device & Qwest DSL Router?

Jul 12, 2011

I am trying to figure out how to network my laptop with my desktop. I have a Qwest DSL Wifi router. My desktop computer is hooked up to a Vonage device/router and then the Vonage device is connected to the DSL router. My laptop is connected to the Qwest router by Wifi. Also, the deskop and Vonage device are setup with a static IP. Is there any way to network between my desktop and laptop so I can do file sharing?

View 1 Replies


ADVERTISEMENT

How To Networking Between 2 Computers

Aug 23, 2012

I tried to read the tutorials from this forum regarding networking. I am too dumb to understand. They are all Greek to me.

Is there a " How-to for Dummies " instructions for connecting my 2 laptop computers ? Windows Vista Home Premium 32-bit SP2 Windows 7 Home Premium 64-bit SP1

They are both wireless enabled, but because my Vista computer battery refuses to charge, it is always plugged in. ( $124 for a battery replacement ? No way. )
In fact both my laptops are plugged in all the time. ( don't laugh ).

ISP is Bell.net.
t-4-2

View 3 Replies View Related

Networking Will Not See Non Win 7 Computers

Nov 25, 2009

I've spent 2-3 days now trying to solve the networking mysteries of Win 7.

In a nutshell. This computer (Windows 7-64) cannot see the other computers and shares on our small studio network except for the windows 7 machines (also Windows 7-64). (the other computers/shares are all XP)

We have 2 identical machines side by side, one can see all the computers, this one cannot. Both are fresh installs.

There are approx 8 other machines/shares on the network.

Both computers have vista installed on a seperate drive that see the network fine if booted into.

Both have homegroup turned off, and have workgroup enabled with the same workgroup name "WORKGROUP". Both have discovery and file sharing enabled. Both use the same network controller, and have the same updated Windows 7 driver.

-I have tried turning on/off iv6 (which I see some people think/don't think is an issue).

-I have disabled FIREWALL

-I have disabled anti-virus

-I have rebooted after each change

-I have tried different locations/cables on the hub

-I have tried the cable/hub location on the Windows 7 computer that is seeing the network computers.

ps. I forgot to mention that if I type in the IP address in addres bar I can access one of the other machines, but it will not show up in the network window.

I am really at a loss, and have read about every post I can find, and tried every suggestion.

View 9 Replies View Related

Networking Two Windows 7 Computers Together?

May 3, 2011

I have a Toshiba Satellite running Windows 7 home pre and a desk top running the same. I want to network the two together so I can share external Hard Drives and such. I want to do this so the files can only be seen and or read by my two computers. I have a room mate who is also running windows 7. What can i do to make sure he dose not have access to my computers?

Both are connected to the internet VIA wireless connection. ( router in room mates room ) I have both computers connected together via a cross over cable also.

View 7 Replies View Related

Networking Two Computers Questions

Nov 20, 2009

Homegroup or Sharing?

Which should I do. Its my home office computers. I'd like to be able to access files between both machines. Doing this, what precautions should I make that noone can get into my system? I'm a little hesitant to share ALL files on both computers between each other. But i'd like to!

I'm playing with Sharing now but i'm noticing that sometimes when I save a file on one computer it isn' accessible to the other computer until I right click and SHare it. I thought by sharing the folder it would just share every new file. Is there a way to do that?

View 4 Replies View Related

Networking With Apple Computers (Leopard / Tiger)

Jan 10, 2009

I will ask for Leopard first since this is what most people are using.

I tried to set up the networking with the Apple machines last night to no avail, rather, this morning. Has anyone had success doing so? According to everything I have read, it should be fairly straight forward, yet it is not connecting.

Any ideas?

View 3 Replies View Related

[Networking] Can't Get USB Dongle To Share Wifi With Router?

Aug 13, 2012

On Windows XP my USB dongle would always share it's wifi connection with my home WRT-54G WiFi Router.It was simple and all it took was a little wizard to set it up and give my router an IP address from my computer.In windows 7 I cant find out how to do it.the internet sharing option doesn't work correctly. it's not giving my router an IP address.

View 8 Replies View Related

DLINK Router And Adapter Networking Driver

Nov 11, 2009

I will be buying a new computer (64 bit). I currently run a 3.5 year old Dell (32 bit) with XP Pro and connect wirelessly with a DLINK router and adapter (DLINK DWA 130 Rev C) which is an N router, which replaced a G level router about 4 months ago. Would it be possible to download a driver that will work on the new machine now, or should I bite the bullet and add an adapter to the new computer? I emailed DLINK and have had no response.



.

View 1 Replies View Related

Can't Connect Two Computers To One Router

Dec 6, 2012

So everything was fine until today when I woke up. My internet wouldn't work, it was saying that I was connected with internet access but never gave me it. I checked my router settings and it shows all the correct things.

So then, I decided to check my brother's computer which is in the same room and he couldn't connect either. I turned my computer off and somehow, my brother's computer had internet access and could access the internet.

Posting from my brother's PC now. I have attempted everything, restarted the power to everything about 5 times. Our internet has always worked and has until today.

View 5 Replies View Related

2 Routers, Can't See Computers On Other Router

Apr 23, 2011

I have 2 wireless routers/switches in my house. I have a router downstairs and one upstairs My setup is currently like this Downstairs: Computer Printer Modem Upstairs computer HTPC (media center pc) I use the printer on the downstairs computer to print everything, and this used to work fine until I installed a new router upstairs. My old setup was that upstairs I had a wireless router, and a separate switch, and the router was feed internet through the switch. Now that I installed a router/switch combo, I cant see any computers except for whats directly connected to the upstairs router.

View 4 Replies View Related

2 Computers Connected To Router But One Can't Get Online

Feb 14, 2012

I have two PC's in the same room connected to the router and receiving good to excellent signal strength. One PC has no problem getting online while the other one can rarely get online. Or, if it does, it doesn't stay online. The problem computer is a Dell desktop using a wireless USB adapter. In the past, in different houses, it has never had a problem getting online. Windows 7 troubleshooting has not been successful.

View 9 Replies View Related

Connecting Two Wireless Computers Without A Router

Nov 2, 2009

This is for my parents house. They have high-speed net that can only be registered to one computer, so running it to a router and then computers is not an option. We used to have it setup with net into "computer 1" then out to the wireless router. The new computer has only one ethernet port, so this can no longer be accomplished without buying another card, which I am very inclined to do. They are getting another computer that will also have Windows 7 and would like to get wireless working again, so...

1) I've tried an ad-hoc connection. I understand the concept and had it working for awhile but found it to be "finiky." I would always have to restart the connection everytime I wanted to use it. I couldn't get it to "stick." Did I maybe do something wrong or is there no way to keep the net connection open? I "saved" the network and set it to start automatically, but it would always close the internet sharing.

2) I haven't messed with home group...will this feature accomplish internet sharing easily??...without messing with any ad-hoc crap? I need everything as simple as possible, so if they have any problems I can fix it over the phone or they can figure everything out for themselves.

Like I said, worst comes to worst, I'll get them another ethernet and run it the old way...was just hoping I could simplify things and save some money.

View 8 Replies View Related

Computers At Home Connect To Same Router But With Different Names?

Apr 15, 2011

All three of my computers at home (all on windows 7 ultimate 64bit) are connecting to the same router with same SSID, but they end up having duplicate names such as NetworkName 1, NetworkName 2, NetworkName 3. This is preventing me from having them share via homegroup. I made sure the computer names are all different and all connect to same workgroup name. Is this a router setting problem? i'm using a cisco-linksys wrt-160n flashed with DD-WRT. i was checking the settings and ran across a new term, vlan. could it be they are all connected to separate virtual networks? i tried to disable vlan, however, that just disconnected all the computers to the internet.

View 2 Replies View Related

Remote Desktop Multiple Computers Behind Router

Nov 30, 2011

I have two computers running W7p that I want to access when I'm away from my office. I am able to use remote desktop from inside my home network on either computer. I am able to access one of the computers from outside with my router set to forward global port 3389 to host port 3389. I am guessing that what I need to do is set up two port forwards in my router; the global port will be different but the host port will still be 3389 in each case. Does that sound right? One thing I know is that going into the registry and changing the host port to something other than 3389 does nothing. In fact, if I do that I can no longer use remote desktop inside my home network. I've looked all over the web today and there are not any clear instructions on how to do this (that I could find). I read the Windows 7 forum tutorial.

View 6 Replies View Related

Router Port Forwarding To Multiple Computers On A LAN

Apr 21, 2009

Any solution to this problem.

I have for example a few machines up and running on a LAN (might be VM's but that shouldn't be an issue).

Say I have five with addresses 192.168.2.2 ==> 192.168.2.6

I might want to RDP to any of these from behind a router.

Using something like No-IP (No-IP - Dynamic DNS, Static DNS for Your Dynamic IP) I can get a an "Internet acessible" domain so I don't need to know the actual IP address that the Internet sees my router.

As I'm behind a router having Multiple domains won't help either as to the external Internet my router is seen as a single IP address.

However the router will only port forward to a single IP address on my LAN.

So if I need to RDP to any other machine on my LAN other than the default one presumably I could only do this by using a different default port for RDP for each of the machines on the LAN. OK not pretty but "Do-able".

Now we get to the real hassle -- If I did this then I'd need a different version of RDP on the CLIENT computer -- not possible if I'm using a work laptop .

Any solutions . I'm totally flumixed by this one.

View 4 Replies View Related

Install A Software Firewall On Each Computers Behind The Router?

Mar 3, 2011

I have a router and I've been told that's all I really need, but is it?Should I install a software firewall on each of my computes behind the router?

View 1 Replies View Related

Upgraded Desktop Computers Now Laptops Can't Connect To WiFi Router

May 19, 2011

Last week I had a Win XP desktop computer. I use a Netgear WGR614 V6 router. I have fiber to the house and use a Cat5e Ethernet cable to connect the router to the wall jack and Cat5e from the router to the XP computer. I also used Wi-Fi to connect my Windows 7 x64 new laptop and an older XP laptop to the Internet. Everyone was happy and all worked well! I set-up a new Dell Windows 7 x64 desktop computer (it currently connects to the Internet just fine).

During the period I was setting up the new Windows 7 desktop I had both the XP desktop unit AND the new Windows 7 desktop connected to the router via Ethernet cables (at that time both laptops could connect to the Internet). After I had transferred the XP files to the Win 7 computer I just shut down the XP computer and removed the Ethernet cable linking the XP computer and the router - the new Windows 7 computer still connected to the Internet fine (as it still does today).

I made 2 changes to the router:
1) I had the XP desktop connected to Port 3 on the back of the router and had the Windows 7 x64 desktop connected to Port 2 on the router.
2) I used Cat5e cable on the XP desktop and used a Cat 6 cable to connect the new Windows 7 desktop unit to the router.

Both laptops see my router name but neither laptop can connect - even ran the troubleshooting routine. Could simply using Cat6 cable be causing a problem (Windows 7 desktop connects fine via the cable, laptops can not connect via Wi-Fi)? Surely just changing the port I connect the desktop cable to the router with wouldn't cause any problem would it? Do I need to do some sort of set-up or configuration to the new desktop unit to make the router Wi-Fi work for the laptops?

View 1 Replies View Related

Qwest 11n Wireless Adapter Driver?

Nov 15, 2011

I just upgraded a friend's HP desktop from Vista to Win 7. The Qwest 11n wireless adapter (actually an Actiontec 802ain) which worked fine in Vista, now has a problem. Everytime the computer is turned off and turned back on, the wireless adaptor disappears from Control Panel>Network Adapters, we need to reload the driver. The driver installation file is loaded on the adapter, we re-install it by unplugging/re-plugging the adapter into the usb port.It is kind of an odd install.t first the adapter shows up as a flash drive and autoplay prompts you to run Setup.exe., then it no longer shows up as a flashdrive._Windows_7.pdfso I do not have to reinstall the driver every time I turn on the computer?It was not like that on Vista.I am wondering if there is a service or something that needs to be started.Both Qwest and Actiontec have no ideas, they say the device is compatible with Windows 7.

View 9 Replies View Related

Find Modem Passwork Qwest?

May 18, 2012

Find modem passwork qwest

View 2 Replies View Related

Have A N Router And Connect A G Device?

Feb 10, 2011

that is the question if you have a N router and connect a G device your speed drops down to G but which are the numbers in mbs?

View 9 Replies View Related

Computers Running Windows 7 Ultimate X64 - No Media Device Detection

Dec 4, 2012

I use my home network to stream music and movies from my computers to my Xbox and TV. Now all of a sudden, nothing. Both computers are running Windows 7 Ultimate x64, connected online through wifi, and connected to the network homegroup (that works without any issues), but neither or them detect any of my media devices. I have a Sony Viera ST30 TV and an Xbox 360, both having wired connections to the same network that the computers are on. Features that require the internet on both work perfectly fine. And I have a viera app on my phone that I used to use to control my tv (the app may not be compatible with my phone). Even having sharing enabled on the computers, they just wont detect my TV or my Xbox. If I connect my laptop to the network via wired connection, my devices are found. If I connect to a friend's wireless network, their devices are found as well. There has been no change on either computer from the last time it was working, till now.

View 1 Replies View Related

What Is Better A Wireless Router Or A Wired Router Router

Feb 20, 2013

To view Netflix or Amazon movies which type of router am I better off with?

View 3 Replies View Related

Forgot Password For Router Cannot Connect To Router

Dec 30, 2012

I need assistance with my router, serial # CSV01H7A3323 broad band router. I do not remember the password

View 2 Replies View Related

Can Use A Wireless Router As A Wired Router

Jan 24, 2012

I am having problems with my wireless adapter Cisco Router Linksys X2000, can I use it as a wired router into my network socket on the computer?

View 3 Replies View Related

Networked Computers - Can't Save Files On Networked Computers

Mar 8, 2012

Three Computers on a home network. Desktop in Office (Windows 7) . Wife's Laptop (Windows 7). My laptop ( Vista unfortunately). Norton Security Suite and all three. I have a network setup and a Homegroup established.

Everything was setup and working so that I could share files between all three. My wife was able to open a desktop file make changes and save it back to the desktop computer.

All of that changed. Now we get a message when trying to save the file. "You do not have permission to save in this location. Contact the administrator to obtain permission".

I have given the entire "MY Documents" sharing permission to everyone. I have checked everything. I have looked over all kinds of forums and nothing has worked.

I am to the point of doing a complete reinstall of Windows 7 on my Desktop.

View 5 Replies View Related

Using Router As A Second Router With U-verse?

Feb 16, 2012

Can I use my netgear DGND3300 RangeMax Dual Band Wireless-N Router with Build-in dsl modem as a second router with u-verse.ty Or not which netgear I can use?

View 9 Replies View Related

XP To 7 Networking

Jun 30, 2009

I set up my 7 machine on an XP network. The 7 machine sees the shared folders, and I can get to them with no problem. When I try to look at the 7 machine from the XP side, it asks for a user name and password. I never set one up, because I would like to run an open network. (I live a mile down a limerock road with no close neighbors.) Can someone tell me what I'm doing wrong?

Why in the world did Microsoft change the default network name?

View 7 Replies View Related

Mac Networking

Jul 16, 2009

I have a new PC running Windows 7 RC, but I can't get it to find the shared folders on my Macs, nor can my Macs see the shared folders on the PC. Any ideas how to get at least one way working?

I'm running 10.5.7 on the Mac, and if I "Connect to Server" and dial in smb:// and the PCs IP address, I get a login window, but it won't let me log in. It says I have incorrect user name or password. But I have no password on the PC.

Also, I followed the advice in another post, Accessing Mac and windows 7 on same network - Mac Forums), but it didn't make any difference.

View 1 Replies View Related

Networking Win 7 And XP Pro

Sep 21, 2009

Windows 7 on Notebook

Network - wired

Network and Sharing lists the following under "Network"

Buffalo_NAS, can access

Computer "Home" (XP Pro), can access

Computer "Acer-2" (this machine - Win 7)

Computer "Work" (XP Pro) this gets the following message when I try to access:-

-------------------------------

Network Error

Windows cannot access WORK

You do not have permission to access WORK.

Contact your network administrator to request access

Windows "help and support" does not appear to be very helpfull.

-------------------------------

Internet access is working, this over the network via a router.

I am NOT a networking expert of any sort and this has be baffled, can anyone suggest what might be the problem please?

The "Home" computer can access "Work" OK

View 9 Replies View Related

Why Is W7 Networking So Different ?

Apr 6, 2009

Right. First off i admit to not knowing a lot about networks but im sure this isnt right. I have a wired network at home and on it i have a Popcornhour media streamer.

With XP as soon as the OS has loaded i can go to the Network browser on the PCH and it sees my work group and the PC and i can access my shared folders. Same thing the other way around. If the PCH needs a re boot its all up and running agin within a min or so.

With Windows 7 7068 i have to wait anything up to half hour before my PCH can see my work group.

Same router, static IP addresses and DHCP server turned off.

Any ideas guys?

View 9 Replies View Related

Networking A DOS Program?

Jan 14, 2013

They have a peer to per network, formerly with two windows XP computers. On the main computer, they have their main accounting program, which runs on a DOS version of Lotus Works. It's old, but she knows it so well, and it does everything they need. She recently upgraded her main computer to Windows 7, and was able to get Lotus Works running, and, with the LW folder shared, they can actually open Lotus Works from a second computer (running Windows XP) just fine. There is no local copy of Lotus Works on the Windows XP computer, it simply starts the program from a shortcut targeting the LW.exe file as mapped. This has worked fine for quite a while.Over the weekend, they wanted to upgrade the Windows XP computer to Windows 7, (replacing it with a new computer) I was able to set up their peer to peer network, mapped the second Windows 7 computer to the LW share and tried to make a shortcut to the LW.exe file. (both computers are now running Windows 7 Pro, 64bit version) I realize I'm going to have to change compatabilty mode, but the problem is getting a working shortcut on the desktop. UAC is off on the second computer, but I get the following message when trying to make a shortcut.:"Windows cannot create the shortcut check to see if the disk is full" The machine where I need the shortcut is running AVG 2012 Free edition and Windows Security Essentials. What would be preventing me from being able to create a shortcut?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved