Moving Windows 7 Install To New HDD - Different SATA Adapter
Feb 2, 2011
In the past I've migrated 7 from one hdd to another by doing a backup to a usb drive, then swapping the drives and restoring to the new one. What I need to do now is a twist on that. My MB is one of the new p67s that has the faulty intel sata ports, and will eventually be recalled. The 4 6Gps sata ports on the board are not affected by the chipset problem, so I plan on just using them instead (plus I just got a 6G seagate drive that I wanted to use anyway). What I envision happening is restoring to the new drive on an entirely different sata adapter and port #, and the system not booting. I assume I could get around this by booting to a command prompt and using bcedit, but am not 100% on that.
I just got my new Vantec IDE/SATA to 2.0 USB Adapter installed. I use it on my laptop to give me extra storage space.. or plan to.. this drive already has a good copy of Win 7 installed and i'd like to boot into it from the USB adapter so it will be easier for me to find out what i need to back up.
I did try to boot from USB and windows does start to load then crashes.. I don't know if it's due to the Vantec unit or if I just need to repair the MBR on the drive. The drive has been sitting in a safe place for about 8 months not being used.
Interaction (interface?) between a Sabrent USB 2.0 to SATA/IDE Hard Drive Adapter Product Code: USB-DSC5 and my Windows 7 Home Premium 64-bit?When connected to IDE Drives Maxtor and Western Digital, and through the usage of Windows 7 it tellls me that the Hard Drive "is not ready". Is that a message originated by the Windows 7 software?If so how do I go about "getting the disk ready" so i could change disk type or number or sizes of each partition and/or reformat?unexpected report from the Windows 7 interaction with this adapter and the Hard Drives it holds, 40 GB and 80 GB IDE drives Maxtor and Western Digital. I am trying to use Windows (or some other third party software) to resize the partitions, change the disk type and eventually reformat.
Just built a moderate spec gaming PC from scratch, and all has went according to plan except when I try to install Windows 7, my hard drive won't show up. My new motherboard doesn't have any IDE slots, but I only have an IDE hard drive. I am using a 'Pluscom Serial ATA PCI Adapter' to connect my hard drive to the computer as it has 1 IDE slot on it. I don't have a disc for drivers and don't know where to start. I am running Ubuntu on it at the moment so I can download any drivers I may need.
When I installed a TF III GTX 570 video card I lost my PCIE-X1 slot and 1 SATA port on the Inspiron 530 Foxconn G33-M03 MOBO I am still running. Now aside from the fact that I need to upgrade the MOBO...
I added a Rosewill RC-209-EX PCI-SATA adapter (SiL3114) to gain back 4 SATA ports. The card is working fine. It is slow compared to the MOBO SATA ports but I expected that. I have a Seagate 500GB HDD and an Optiarc DVD R/W drive attached to it. BUT..... I can not boot from either device. They do not appear in the boot options....
Based on my reading I got the "NON-RAID" (IDE/ATA emulation) BIOS from Silicon Image and flashed the card's BIOS since I will not be using it for RAID. It is just for more SATA ports. Should I be able to "see" the PCI-SATA card and its attached devices in the 530's BIOS Setup Screen? Is it a limitation of my Dell neutered BIOS?
The RC-209-EX documentation specifically states it "supports" CD/DVD drives.
There is plenty written about booting from a RAID array configured to the RC-209-EX but very little about booting from single device.
I am trying to access my wife's macbook hard drive via my Windows computer using the Vantec SATA/IDE to USB 2.0 Adapter. The Apple techs said they could not get the drive to register when they hooked it up. However, we gave it a good drying with blow dryerThe adapter works fine and all the correct drivers installedI am in disk management and the 250GB drive seems to be showing up. However, it is not showing up in My Computer and right click shows "assign a letter" is grayed out.
2 hours ago,i wanted to install windows7 on my sata disk ,cause i destroyed my old partition with ubuntu 10.10. So i started to install Windows 7 .However it couldnt be normal.Then i get an error: . A partition on the disk''0''could not be formatted .The error occurred while preparing the partition selected for installation .Fault code: 0x80070057
So I spent a lot of time getting my windows 7 install the way I want. I plan on upgrading to a new lenovo w530 when they are released relatively soon. I'm not sure the best way to move my windows installation EXACTLY like it is to the new machine. I will be transferring the physical SSD itself to the new machine so imaging it to a new drive i not a step I need to take.
I have a 320gb (255 free) drive and just purchased a 120gb SSD. I have external SATA -> USB bays and extra computers that can do the transferring. My windows partition is currently only 45gb. The current 320gb drive has 4 partitions 2 of which are 10g+ recovery partitions I no longer want. (and can use the space now that I am on a small drive). Windows 7 built in backup will only image the exact partition sizes, meaning if I was going to a bigger drive that's fine I could resize after. but because im going to a smaller drive i cant even write the image to it. Acronis this got me very close, it cloned the drive (including recovery partitions, but i planned on removed those afterwards) but failed to boot, I ran windows recovery to try and rebuild the boot sector but it wasn't able to. How can I keep everything but switch drives? The best thing I can think of now (and very sad) is to install a fresh copy of windows 7 than erase the install partition and copy over the install partition from the 320gb drive, and I have a strong suspicion this wont go smoothly.
I'm trying to do a fresh install of windows 7 and it wont recognize my hard drives. I've done some research and determined i need the correct drivers, but i don't know which ones. I'm trying to install them on 3 WD3000HLFS in RAID 0. The HDD are plugged into SATA 6 ports( only 2 SATA 3 ports on the mobo).
Using Tyan K8W Thunder s2885 in rack mount case. The board is over 10 years old. Dual AMD Opteron 250 processors, 64 bit. RAM 8 Gb. ATI Radion HD 3650, AGP. There is only the video card, driving a single LCD monitor, PSP mouse & USB keyboard, and the HDD attached to the board, no peripherals.I am installing Win 7 home Premium 64 bit. I have had Windows 7 running on this board for over a year, from an IDE 80 gig drive.I installed a new SATA 500 gb and have only that drive in the case.
I have to manually load 114R5_x64_15150_logo drivers for Sil Image SATA controller, from a USB drive. I have just spent a day learning about and using DISKPART to finally be able to start the install. The install starts OK, expands and loads files. About 2 minutes into 'expanding files' I get BSOD, STOP: 0x00000124,(0xFFFFFA800643F038,0X00000000B604A001,0X000000000000813)I have repeated the steps and reproduced the problem at about the same time into the install. I have no idea if there is a way to read/post a log. Since windows is not installed, there is not the usual dump available.
Well, I've done a lot of research (googling) on whether or not to install Windows 7 on my solid state drive in AHCI or IDE sata mode. I wanted to confirm it with you guys to make sure I got this straight before I go ahead and install Windows 7.
If I install windows 7 on my solid state drive in sata mode ahci then later I can go to IDE if I wanted to by just switching it in bios. But if I install windows 7 under IDE mode then ill have to do a registry value change to make windows 7 work in ahci mode.
Everyone seems to have a different opinion on whether or not ahci mode is faster or worth it over IDE mode for windows 7 on a SSD. I'm not all that interested in hot swapping so thats not a interesting feature for me. I'm looking for reliability as a top priority.
I am building a htpc but cannot seem to get windows to install onto my SSD.The SSD is visible in BIOS and on the 'where do you want to install windows' screen.I am wondering if that is because the OS cannot install to my mobos sata 3 portsI havecrucial m4 SSD 4GBMSI H61MA-E35 with usb3/sata3The sata 3 ports are ASmedia according to the manual.i think i know where this is heading and will be fairly annoyed if so because i bought this board specifically for the sata 3 boot drive option.
ASUS P7P55D-E EVO 2X80gb Western Digital SATA Drives 2x2TB Samsung Spintpoint SATA Drives
I have already been using the machine with another 80Gb Western Digital SATA Drive with Windows 7 Pro 64Bit installed and now want to convert to RAID 5 for redunancy in case of Drive failure (We all say we will back up but we are all lazy when it comes to it LOL).I have taken out the original OS drive and plugged it into the E-SATA connector on the MOBO, gone into the BIOS, turned on RAID for the SATA Ports on the MOBO, and connected the 2 X 80Gb Boot drives. Entered the Hardware RAID Controller POST, and created the RAID 5 Volume from the 2 X 80Gb Discs.Now boot with Acronis Wester Digital edition.Clone the Original 80Gb Disc to the new Raid Array.Shut machine off, remove original OS 80gb Disc from E-SATA port.Boot machine.It starts to boot, and gets as far as the Windwos 7 Microsoft 4 Colour logo and then I get an error and then have to boot into Windows 7 from DVD and go through the repair process.When the Repair has run it reports the following:
The following startup option will be repaired:
Name: Windows Boot Manager Identifier: {9DEA862C-5CDD-4E70-ACC1-F32B344D4795}
The following startup options will be added:
Name: Windows Recovery Environment (recovered) Path: Recoverye52d0bc2-1f15-11df-af10-d764fe3715b8Winre.wim Windows Device: Partition=D76190 MB)
A copy of the current boot configuration data will be saved as:C:BootBCD.Backup.0001 However it fails to do the update How do I get this RAID to boot successfully? I *don't* want to have to re-install the Operating System as that is just too painful a thought?
Is it possible to move my Windows 7 installation from the partition (both the Sys. Reserved & OS partitions) of one drive on one controller to the partition of another drive on a different controller, AND have it boot? I know "something" would have to altered, but I'm not sure "what" or "how". Is this even possible without going through a lot of hoops. Specifically I have an installation of W7x64 installed on the 1st partition of the master drive on a PATA controller. I want to move it to the 1st partition of the master drive on my SATA controller.
FROM PATA0 {sys reserved}{OS install}{data} TO SATA0 {sys reserved}{OS install}{data}
I also have another install on the 2nd partition of my SATA4 controller and want to move it to the 1st partition of my SATA0 controller
FROM SATA4 {data}{sys reserved}{OS install} TO SATA0 {sys reserved}{OS install}{data}
I have just bought two brand new WD 500 GB RE4 HDD's and connected them coorectly for RAID 1. I have changed the BIOS and Pressed Ctrl+F to create the RAID and this has been successful. When installing Windows you obviously get to the aprt where you need to load the floppy drivers to locate the drives...
I have downloaded ever driver from the Gigabyte support drive and loaded them onto a USB, not one driver can be seen when the USB is "Browsed" too...
How important is it that the drivers are on a floppy, as I do not have a floppy drive or access to a floppy and drives. Also what driver should be downloading as I tried the 3.2.1540.17 one and that was not seen, so I just downloaded them all in an attempt for success.
Windows 7 64bit Pro SP1 OEM System Builder Pack Gigabyte H77M-D3H 1TB SATA HDD WD Caviar Black Intel Core i3 2125 DDR3 8GB 1600 Intel Viper SATA LG Blue Ray DVDRW
Clean install of Windows reveals an error not detecting any drives, does not allow partitioning or formatting. BIOS identifies the drives.I've attempted installs of updated drivers from the motherboard's website (as well as the CD that came with the motherboard). WD claims not to have any drivers on their website. Still nothing.
I am doing a motherboard upgrade for a friend. I need to know how I can move his hard drive with his current OS instal to the new motherboard without having to do a fresh Windows 7 install. He has too much that cannot be replaced. Is there a way to do this?
i installed a sata controller because the sata controller on the motherboard went out. I can easily install ubuntu but when i try installing win 7 it asks for a cdrom driver, when i try booting from usb it asks for hdd driver.
This seems to be such a frequent issue that it could/should be a FAQ but I haven't found my answer yet.
I am (currently) running Windows 7 64 ULT on my home PC. I purchased an Intel X25M 80GB SATA drive and connected it in order to benefit from the speed. The issue is that setup hangs during the "expanding files" on this drive. Looking back I have *never* been able to install windows (XP Vista or 7) on a SATA drive on my mobo.
In order to avoid confusions I did the following.Removed the 2x400GB striped drives. Removed the old PATA-IDE drive, therefore only drives available were the Optiarc DVD and the new Intel SSD.
I have a HP m7667c, which has two SATA drives. The motherboard is ASUS P5BW-LA (or Basswood-UL8E). I've never successfully installed vista before because of it kept asking for SATA drive. I wonder if there is a solution for this problem with Window 7?
I think I have RAID on in the BIOS configuration but I don't really want to turn it off because in that way my old WinXP would die. I just wanted to give Windows 7 a try before I completely change to it. Could anyone help me? I could provide more information about the desktop if necessary.
I've just bought parts and collected a new PC system. My Motherboard is AsRock M3A785GXH/128 ASRock > Products > M3A785GXH/128M
and regarding to the manufacturer it should be Windows 7 hardware ready.
But I can't install Windows 7 pro 64 bit on my new system. The Windows 7 installation application can't see my harddrives and want a driver to them. I assume that should be a driver for the SATA controller on the motherboard. I've tryed to use the drivers on the motherboard cd-rom and tryed to use the drivers froms asrock homepage, but Windows 7 wont accept them.
I have contacted AsRock about this issue, but I'm wating for an answer and hoped that you guys might has seen this problem before, and will answer quicker than AsRock Support
I should say that I cant install Windows Vista Business 64bit without any problems at all.
The mobo's kinda old, and not the greatest; the builtin SATA only works for Raid, so I put in a PCI sata card with the SIL3114 chipset. The computer now sees the 64GB SSD Patriot HD I'm trying to use for her C drive (The SSD is a leftover from a different project... I thought it'd lend some additional performance to help make up for the 1.2 ghz cpu). When I get into Windows setup, though, Windows 7 does not recognize the drive, and none of the drivers that came with the PCI card seem to work. I suppose I should have double checked before buying the SATA PCI card to find one that has native Windows 7 drivers, but I thought the stone age days of needing SATA drivers were over, guess I was wrong!
I am attempting to install a Windows 7 OEM x64 onto an older machine I have. MB is a Foxconn NF4UK8AA-8EKRS, CPU is AMD Athlon 64 x2, 4200+ 2.25 GHz, RAM 1GB. I installed a new OEM 500GB SATA hard drive unformatted.
Current OS is Windows XP Home SP2, I deleted SP3 since it was giving me some problems with auto login.
My DVD drive will not read the Windows 7 installation disk, similar to another post the drive just flashes, never spools up. It will read other CDs and DVDs.
I initialized the hard drive but have not partitioned or formatted the new SATA hard drive which is where I want to install the new OS. While the BIOS recognizes the drive, its not listed on Computer tree.
I have copied the Windows 7 OEM DVD contents onto a Folder that I created on a Toshiba External USB drive. Only had a 2GB USB Flash Drive so thought I would use the external drive and select the setup.exe in the Windows 7 files I copied into a folder without formatting a complete 250GB ext USB drive.
Question, can I partition and format the new SATA drive using the Windows XP Home Edition with an NTSF format and will this be recognized by Windows 7?
Question, can I install Windows 7 from the Toshiba Ext USB drive's folder onto the newly formatted SATA drive? Or does Windows 7 require a different formatting setup?
The BIOS and MB won't recognize a DVD drive it only allows a boot from CD. I removed the CD and DVD master/slave parallel cable and only installed the DVD as the master, but Windows 7 DVD just blinks and never spins the drive.
If I can get the new OS installed I'll remove my two older 40GB PATA hard drives and add more RAM. This machine is for my wife's use since it was in the garage gathering dust. Thought I would revive it and set up a wireless home group between my machine and her's. I added an all in one printer/copier/scanner in addition to the HP Photosmart D7460 I have so we can share files, printers and Internet connection.
I have been building my own machines since about 1990. Building a machine is fun (takes maybe 2hrs) but all the software kicks my butt. Also I went to the OEM System Builder License at Microsoft OEM Partner Center that is the most confusing arrangement I have ever seen. I'm just a home builder having fun, not a business, must I buy the full version to get this installed?
I originally only had a HDD for my computer with Windows 7 on it. I got a 180 GB Intel SSD today and installed Windows 7 on it. When I installed I made sure to unplug the data cable on the HDD. After everything was installed I plugged the HDD in and made sure it booted the SSD in the BIOS.
I went into the HDD to open Steam thinking that it would open fine. It wanted me to update everything so I went ahead and did that. Then I noticed a ton of random icons on my desktop. I realized all of these were from the Steam folder. I have no idea why they're on my desktop. When I try to delete them off my desktop it won't let me, saying Steam is using it. Is there something I have to do to make my SSD and HDD work together?
Also with Steam; after I updated it none of my games were installed. They are all installed on the HDD but when I try to click on a game it wants me to install it again. One more thing, whenever I open a program in the HDD it wants to update and install it into the SSD
Very little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
I had to do a fresh reinstall today and I wanted to know if I should download and install any of the drivers (other than Ethernet LAN to get me online) for my comp'?In particular, the SATA drivers for a 64-bit install http://ca.gigabyte.com/products/pr [...] l=1#driver,I do have to install the audio and video, but otherwise, not sure about the SATA.