How can I be connected to multiple routers? So I can, for example, have one wired connection and maybe two wireless connections? Do I have to have many network cards, or can I use a program or so?
View 5 Repliessetup two routers (Netgear N600 routers)? In House A (My Barn) I have 3 camera's hook up to my router. In House B (My House), I have a N600 hookup to my modem and 3 of my computers. What would it take to be able to hook up House A to House B, so that I can view my House A camera's?
View 6 Replies View Relatedi'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.
at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.
then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.
i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.
for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.
I recently for the first time went over my monthly data cap for broadband and looking it to it a bit more it looks like a lot of the programs my kids are using are hogging the bandwidth. I don't really want to pay for more bandwidth (as I already pay way above average as I live in a small rural village) but I don't want to restrict too much what my kids are doing. The solution to me seems to be to see if I can monitor and if possible control to some extent the data on each of the IP connected to the router if that is at all possible. I have looked at my router settings and unfortunately they do not permit anything more than traffic monitoring and there are no custom firmwares to allows additional features of any use. Is there any software that I could use to do this?
View 1 Replies View RelatedI have a peculiar network setup that causes me to require two routers.My laptop connects to router B, which then connects to router/adsl-modem A.
{Internet} ===MTU:1460===> [A] ---MTU:????---> [B] ===> Laptop
I have set up router A with all the correct settings provided by my ISP, one specifically being the MTU of 1460.I now need to know what I should set router B's MTU at. Should it be the same at 1460, or the full network speed of 1500.
I am running Windows 7 RC 7100 (of course) and I'm wanting to get a network setup between two computers over two routers. Here's my story:
I just moved in with two of my friends and we have 6 computers (3 laptops and 3 desktops) and we have 2 360s and 1 ps3. So needless to say my friends 5 port router wasn't enough for all the equipment so we decided to use my router with his.
Now after a day of configuring we have it running smooth and playing games with no troubles but there is one problem we want to access media on the ps3 from all the computers. I can access my media from the ps3 no problem since I'm on the same router as it but I can't access my friend media because he is on the 2nd router.
We have two belkin routers the main one has my friends PC, his 360, his ps3, and my router connected to it. My router has the remaining two pcs and my ps3 connected to it. Does anyone have a solution to this problem? I have tried putting the systems on one work group but that failed.
I also tried connecting to one homegroup but I can't detect his group and vice versa. If anyone could tell me how to set this up I would be grateful. My friend thinks it's might involve the routers DHCP but I'm not sure.
The scenario is: I have a PC running Windows 7 which is wirelessly connected to my Netgear modem-router. I wish to install a security camera outside my house, instead of running a long ethernet cable all the way back into my house from the camera to the Netgear, is it possible that I can connect the camera to another router outside, and then get that second router to communicate with my Netgear inside the house, and thus be able to control my security camera from inside?
Now I know the security camera can be connected to a router, and I can install software to remotely control it, but I'm not sure how I can go about using my Netgear to communicate to a second router. I haven't purchased the second router or the camera yet, but I want to know if it's possible before I do.
I am planning on holding a LAN Party in a month or 2 and requier a bit of help because it is my first. About 6 - 10 people will be coming.
I need help on a few things and any imput people could put in would be greatly appreciated because I am very lost!
I was planning on purchasing a switch (Still not sure what to purchase yet. I am looking for something around 10 ports) and connecting it directly by a network cable to my Belkin Wireless G Universal Range Extender Router. Then connecting all the computers to the switch. All the computers connected to the switch will be running either XP, Vista or 7.
Is this going to work? What kind of settings am I going to need to change on the OS's to make them all be able to interact with each other in the games. Are their easier ways to do this?
I have no previous networking experience and am only 14, so go easy.
i have a brand new toshiba laptop connected wirelessly. however it keeps showing connected however no internet access.i have a notebook as well that is brand new and it connects no problems what so ever.im using windows 7 home premium and 64 bit os.
View 1 Replies View Related802.11n wireless router: is this hardware supported by all windows operating systems?I am planning to buy one for my brother, he is using windows XP. I am using Windows 7, and my brother in-law is using windows Vista. We all play WoW or Heroes of Newerth together in my bro's house. So I am wondering if this would work for all the three computers. Also my brother who has XP is using a Desktop.Does it need any Wireless adapters for it to recognize the signal from the router?
View 5 Replies View RelatedMy Router is dying ( Always needs re-booting ), so i decided to get a new one, after some reading i found that N routers are the Top now, but you need a laptop that support N routers . My question is how can i know if my laptop support A G or N routers .
Laptop : Dell Inspiron 1545
Network adapter : Dell Wireless 1397 WLAN Mini-Card
Marvel Yukon 88E8040 PCI-E Fast Ethernet Controller
OS : Windows 7
I have 2 wireless routers/switches in my house. I have a router downstairs and one upstairs My setup is currently like this Downstairs: Computer Printer Modem Upstairs computer HTPC (media center pc) I use the printer on the downstairs computer to print everything, and this used to work fine until I installed a new router upstairs. My old setup was that upstairs I had a wireless router, and a separate switch, and the router was feed internet through the switch. Now that I installed a router/switch combo, I cant see any computers except for whats directly connected to the upstairs router.
View 4 Replies View RelatedI have a netgear router wgt624 v2. I've had it since 2003 or 04. when I got it my network seemed to be fast and connections to it quick.now sometimes my wireless seems to have a moment or two where it searches for a connection. I figured that was due to all of the neighbors who now have wireless too. and sometimes now devices are having ip conflicts. for example my printer is set to use a static ip and the router will often give that ip to my laptop. so then the printer will not work unless I restart the laptop.
View 9 Replies View RelatedFor some reason the network from point A to B keeps failing. Going to explain the set up I have right now. DSL and modem are in room 1 then that plugs into the wall to the switch in room 2. Many things are connected to the switch, roku player, dish network receiver and other Ethernet connections for other rooms and a router so we can get wifi. Now for some reason the connection from the switch to the modem keeps going out. The internet works just fine because i can plug the ethernet cable from the modem directly to a computer in the office. However from a computer in another room I cannot cmd ping the modem says 0%. What would cause this to fail, it works for hours then i have to unplug/re-plug the cables to get it working again.
View 9 Replies View RelatedMy Nephew has a very long house and a computer cannot get a signal from the wireless router which is at the other end of the house. He doesn't want to run RJ45 cables. Could he use 2 routers so the second one connects wireless to the first one which is connected to his adsl phone socket by a ethernet cable. If so how would I go about setting them up, settings wise. If so would the computer also be able to talk to each other to be able to transfer files etc to each other.. (enable workgroup & sharing drives/folders) I know how to setup this bit.
View 4 Replies View RelatedWhat is the process that goes on when data is transmitted between two routers?
View 2 Replies View RelatedWindows 7 home premium 64 bit I have a D-Link DIR 825 router and when I open Network & sharing, under Network Infrastructure I see a Linksys wrt110, at times it's icon goes away for a few minutes, then re-appears, If I right click on the icon I don't get a delete option (greydd out), if I select properties I'm asked for a PIN number. I don't own a Lynksys router and I'm wondering why it's showing up on my network?
View 9 Replies View RelatedI'm having to write this because my old bridged network worked so well for so long that I totally forgot how I ever set it up in the first place, but I recall that it was simple and involved:
- The two were connected via wifi - the primary one having a physical connection to roadrunner modem
- The two had the same SSID, same Security method and passkey, different base IP addresses [192.168.1.1, and 192.168.1.21]
- beyond that it gets hazy... what "mode" was the secondary in? somewhere I input to the subordinate router the MAC address of the primary router... dunno where/which field accepted that
- do both need to be set to a fixed & same channel, as opposed to variable/Auto?
- what all was turned off on the secondary?
- both had full use of both their wired connections/clients and wifi
- one of these is N-300mbps, and g/b, the other is g/b. do I need to limit anything?
Its not necessarily important to me that the connected devices all share with one another - I have strange clients anyway and its not needed. the windows 7 devices will be ok on the homegroup.
I have a wireless router linksys connected to the modern witch is on the second floor. I want to connect another router linksys on the same network that the one on the second floor is on, wirelessly without any cords on the first floor.
View 15 Replies View RelatedI noticed a few days ago that I cant access my router anymore "http://192.168.1.1/"I had some network problems so I uninstalled hamachi. Ethernet 24mbps connection crashes every 10mins~There's the thread I made, and all of the changes I did I posted there. So if you read the thread. When I got back home and after few days I noticed that I can't connect to the router anymore. ipconfig just displays some random "85.157.0.1" which doesn't work.
View 9 Replies View RelatedI earlier (roughly 6months ago) made a topic about this. (Can't access routers webpage / control page anymore.)
I recently got a brand new computer with a fresh copy of Windows 7 Pro 64-bit SP1 and the same problem is still there. The problem is: I can't access the routers webpage when I'm using ethernet. It's fine when I'm using wireless, but the thing is I don't have a adapter built in to the pc, so I had to use a USB adapter which my brother took.
So, I'm stuck with the ethernet cable. I got two cables, both of them give the same results, so atleast it shouldn't be the cable or such. Also, I can easily access the page on my mobile and laptop.
My laptop was hooked up by broadband cable to the faceplate and was working fine, but now both cabled and wireless internet don't work, however I can connect to wifi on mobile. The troubleshooter does not run, it just reads error. I bought a brand new cable but still no luck, have tried undoing system updates but it has merely made it worse
View 2 Replies View RelatedI just noticed this that when you open the network from the desktop it says its not connected but when you click on the network icon in the taskbar it says its connected is anyone else having this problem.
View 3 Replies View RelatedI am trying to get my wife's new computer up and running without any BSOD or program failures. Note that the system was not initially set up to capture the dmp files so all the earliest ones are missing. I presented the initial problems to the original seller who recommended sticking with MSE and uninstalling Norton 360 and I did that. Another forum suggested that Virtual Memory was the problem and I disabled and restored VM. Still having multiple crashes and I am hoping that I can get real help here. I do note that all the crashes have ntoskrnl.exe in the driver stack although sometimes alone and sometimes with other drivers.[CODE]
View 2 Replies View RelatedWe have three medical clinics and the front desk staff float from clinic to clinic depending on their schedule. I only started here a few months ago and I am working on upgrading their Dell xp systems to Windows 7 systems.The problem begins to crop up when say a user named Sally will come in and sit down at this system for the first time.. Well, she needs to login, click on outlook icon, let it find her exchange PST and copy settings to her user profile, then she launches the application for the scanner that she uses to scan in ID's and insurance cards for every patient coming in.. The scanner is set to default settings and needs to be tweaked on color depth and double sided, etc.. Then after that, she needs to launch her Medical EMR application.. and then choose various options in the citrix client, ..TL;DR - Each user needs to spend 20 minutes resetting the defaults at this updated system.
Well this is fine except, I am planning on updating 2 front desk systems at each clinic, the user Sally will need to do all these things EACH time she finds herself sitting down at a system I just swapped out the previous evening.My thought is this, put a single system down in one clinic and let it sit a week giving most of the float users a chance to work on it for a day, setting all of their preferences etc.Once I get a bunch of them with user profiles on the local drive, grab an image of that drive and just deploy that to each system I roll out..Couple issues I am running into:First would be that I would have to register each Windows 7 copy with a new serial, which I have The next issue is, we have a mis-mash of Dell optiplex systems. 330's - 380's even a couple 320's..
I have been getting a fairly random blue screens and I cannot pin point it myself. I know a bit about diagnosing and repairing issues but this one is just a pain in my butt. I am uploading the dump files and I hope someone can give me a hand I am running a sfc scan right now to test for any problems too. Also got this off the TSG SysInfo Program.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: AMD Athlon(tm) II X3 445 Processor, AMD64 Family 16 Model 5 Stepping 3
Processor Count: 3
RAM: 8191 Mb
Graphics Card: NVIDIA GeForce 9600 GT, 512 Mb
Hard Drives: C: Total - 476837 MB, Free - 246483 MB;
Motherboard: BIOSTAR Group, N68S3B
Antivirus: Norton Security Suite, Updated and Enabled
I have attached a second monitor to my laptop which runs Windows 7, however, I need to set different resolutions for different monitors, because the display does not fit to fill the screen on both monitors.
It is also noted that the display is replicated, and I would like to have the effect of having different desktops e.g. being able to use different applications such as debugging code on one monitor on an IDE such as Visual Studio, and, viewing the browser on the other monitor.
Currently it does not seem possible since the behavior seems to be that the same resolution is replicated on both monitors.
I use WhoCrashed to analyze these errors but I dont know how to solve. Maybe my hardware cause these.
Processor: Intel Core 2 Quad CPU @ 2.40 Ghz
Ram: 2GB Corsair
OS: Windows 7 Ultimate 32-bit
VGA: ASUS 8600 GTS
Mainboard: ASUS Striker Extreme
I'm having a bit of trouble trying to get two monitors, a small 1024x768 LCD, and a 46" 1920x1080 TV, to display the same wallpaper at different resolutions. My graphics card is older, a Nvidia Quadro FX 1700, but it is perfectly capable of driving both displays at the same time. It's a minor annoyance, but I'd like to get it working if it's possible.
View 4 Replies View Relatedit's a western digital but when i uninstall a program or if a scan is completed a pop up screen comes up with the sound for the hard drive it sounds like a horn when i get popups from uninstalling or installing something
View 1 Replies View RelatedI am getting this message after having added two new entries to a registry earlier today. Since then, I have deleted the two entries and the problem persisted. I've also done a system restore from before the incident and that hasn't helped. Lastly I also uninstalled and reinstalled the network driver.I know my Internet isn't the problem as my phone works with he Internet just fine.
View 1 Replies View Related