I have an external USB 3.0 HDD as well as an internal SATA 3 HDD. I am unable to eject (ie "Safely Remove Hardware and Eject Media" ) either the drives because I get the error:Quote :This device is currently in use. Close any programs or windows that might be using the devices, and then try again?
View 1 RepliesI'm running on a relatively new install of Windows 7 64bit Ultimate. I recently (about 2-3 weeks ago) installed a new HD and decided to have a fresh start so everything was formatted followed by win 7 install. Everything has been running great up until mid day yesterday. Out of what seems like nowhere I experienced 6 or 7 BSOD's yesterday and from what I could tell they occurred when I tried to do any of the following: 1. Access drive D and play a video file (This is the new HD, it would instantly BSOD). 2. Access internet within 1 minute of startup.
Since yesterday I haven't had any BSOD's and have had the computer running, I haven't tried to play any videos off of HD and haven't reset my computer since (hoping that whatever it was has gone away, although I'm sure it hasn't). For the record I have accessed some music files on drive D without any issue, as well as several word and excel documents (not sure if that makes any difference?)I have a feeling it may have something to do with my new HD that I installed, but have no idea what it could be as it was running without issue up until yesterday (for at least 2 if not 3 weeks).
My system specs are as follows:S: Windows 7 64bit UltimateManufacturer BIOSTAR Group Model A740G M2+ Total amount of system memory 6.00 GB RAMSystem type 64-bit operating system umber of processor cores 2 isk partition (C) 272 GB Free (298 GB Total) isk partition (D) 1630 GB Free (1863 GB Total) isplay adapter type NVIDIA GeForce GTX 460 other info:-all drivers should be up to date to the best of my knowledge- i've looked around and have seen a lot of recommendations to run memtest? I have yet to do soI've enclosed a system health report and minidump file as outlined on forum requirements.
I'm trying to get rid of all of the CD drives that are showing up under "devices with removable storage." The go from CD Drive ( F: ) all the way to ( X: )...is there a way to get rid of these?
View 4 Replies View Relatedmy Laptop lenovo DVD drive ejects by itself as soon as the laptop is turned on.. Before it started it used toe take a long time to read a disk and than would eject it giving an error message Please insert a disk in drive. After a while it just kept ejecting as soon as its turned on.
View 2 Replies View RelatedI cant find mt dvd/cd-rom on my computer,its not ejecting either.
View 1 Replies View RelatedMy CD-ROM drive keeps randomly ejecting, then going back in by itself without me doing anything. I can just sit and watch the computer (a desktop) as it does this.It's also not doing it at regular intervals. It just started doing this, too. I had updated my Java, but that's the only thing I did today; I don't know if it's related
View 4 Replies View RelatedHow can I solve this problem?My Acer computer disc drive has always ejected discs whenever I try to insert themI never receive any error message, it will not even try to pull the DVD or CD in.
View 3 Replies View Relatedwhy should I go through the icon dismount instead of just pulling the media when file transfer is done?
I've done it with SSD's directly many times with no problems. perhaps platter drives need time to park?
I routinely get the "This device is currently in use" message when I try to eject an external drive from my Windows 7 64-bit OS. I have no idea what program might be accessing the drive to cause that message. How do I find out? I can, of course, reboot, but that shouldn't be necessary.
View 3 Replies View RelatedVery little, all the parts were shipped here about four days ago and I spent a couple of hours putting them together. I ran into a hiccup when Windows 7 Home Premium would not get past the extracting phase of the installation, kicking up the error in this thread. I began the first install on a 20GB partition, when that failed I tried just installing it on a single partition. When that failed I tried removing all the partitions and just installing on the unformatted drive, in it's entirety (seemed weird but others said they had luck with this).Testing Methodology:
At the end of each attempted solution I tried to install Windows again.My keyboard is a USB keyboard. All of my boot testing is done with a bootable USB that I have running MS-DOS 6.22. What I Have Tried:Solution 1: First I went into the bios and changed the SATA controller from AHCI to Raid SATA Result = FAILEDSolution 2: I tried burning OEM Windows disk from Microsoft to an iso at the lowest speed possible for my DVD burner (4x).Result = FAILEDSolution 3: At this point I had created and deleted so many partitions I was concerned it may be having an effect on the install. So I went to Samsung's website and grabbed their HDD utility tool. I figured let's kill two birds with one stone and test the drive while also restoring it to it's original state. So I did a low level format and then ran the HDD diagnostic. All came back with no errors. Result = FAILED
On to memory...Solution 4: I downloaded Microsoft's Memory Diagnostic Tool and let it run overnight. It returned no errors. So I decided to use MemTest86 4.1 and let it run for 10 passes, I did find errors then. As of now I am running each module of memory one by one to determine if it is a problem with them or the sockets on the motherboard. So far I have been unable to reproduce the errors I got when both modules were running together. As a precaution I double checked the motherboards specifications on the socket order for memory, all is to specs. Result = [PENDING]What's Next:After my current memory test ends, I plan on checking my BIOS to see if the correct memory speeds were detected in the auto detection. If at that point I'm still unable to reproduce the memory errors, I'll put both memory modules back into the system and run the testing again to see if I can reproduce the errors I got the first time.
Yesterday I had a PC technician around to see why my PC was not booting-up properly and also to change my SSD to a larger SSD. As I am visually challenged I cannot do hardware upgrades etc, so I got a Techie guy in. We used Zinstall HDD by-the-way and I would highly recommend this application for such a job plus, it is extremely fast.Anyway, while he was diagnosing my boot-up issue he discovered I had a malfunctioning network card; while removing this, he noticed all the SATA settings were set to SATA 2.When he reset these to SATA 3, the PC would not start-up! When he set them again to SATA 2 there was no problem and it worked fine?
View 9 Replies View Relatedi want to make my spare sata hard drive as a slave my master hardrive is also satahow to do it . my OS is win7
View 4 Replies View RelatedOn one of my Win 7 Pro computers, I almost always get the error message when trying to *eject* a flash/thumb drive: "Problem Ejecting USB Mass Storage Device. This device is currently in use. Close any programs or windows that might be using the device, and then try again." This occurs all the time, even when I close down Adobe Illustrator, the program I usually copy a file from onto the flash drive.
View 1 Replies View Relatedi can't solved it what can i do to solve it
View 2 Replies View RelatedI recently installed windows 7 on my dell xps m1530 laptop. Till yesterday, the dvd drive was working perfectly fine, but yesterday, it just suddenly started ejecting all the cd/dvd i inserted. I tried using Microsoft trouble shooting, and when I chose that I was having a problem in playing the dvd, it started scanning for errors, and i inserted a dvd during it, it started working. But when the program ended, it found no problems. After closing the program, I inserted another dvd, and the same problem. The dvd drive is TEAC DVD+-RW DVW28SLC. I have tried reinstalling the firmware using device manager but it doesn't work.
View 4 Replies View Relatedi purchased a Silicon SiI3512 SATA Raid Controller purely to have 2 extra SATA ports which I am using to connect to my case's external drive bays. I have flashed the bios of the controller and updated the driver to put it in "Base" mode so it is not using RAID. I did extensive research on this and it appears that I have this part right. For now, I am trying to connect a WD1600BEVT 2.5" SATA-II hard drive to one of these ports and am having some difficulty. I can see the drive, but when I try to format the drive in Windows, or a command prompt (using the windows recovery DVD) it hangs. I am wondering if this is a compatibility issue with a SATA-II drive on a SATA-I controller, however, most of the forums I have read state that if there is a compatibility issue, the controller won't even recognize the drive. I searched around to see if there was a way to force the HDD to SATA(150), but the jumpers on this drive are for SSC and RPS. Is there a way to fix this or do I need a drive that is capable of forcing SATA-I speeds? Perhaps even a controller capable of at least SATA-II since that is the minimum of all new HDDs?
View 5 Replies View RelatedMy MB supports only SATA 2 but in my city, the HDD SATA 3 is more cheap than SATA 2. If I buy the HDD SATA 3 it will work with my MB SATA 2 controller?
View 5 Replies View Relatedi'm looking to upgrade from a HDD to SSD. I've been reading online about my board and apparently the marvell 9128 controller sucks speed wise. I was looking at the Corsair Force 3 because of the read/write speeds. Upon doing more digging though it looks like id be better off running a drive on the SATA 2 ports.
View 2 Replies View RelatedThe hard drive in my son's laptop has died, it's a SATA 1 (1.5Gb/s) drive. Can I upgrade it to a SATA 2 (3.0 Gb/s) hard disk?? It's in a Toshiba laptop.
View 7 Replies View RelatedI was wondering If I have one sata 1 and an new sata 2(or 3) on my PC installed on my PC will cause problems in transfer speeds? My Blue-ray is sata 1 also.Does this mean that all disks will work as sata 1?
View 2 Replies View RelatedI am installing a game cd. when i insert that particular dvd and when i try it to open manually a dialog box shows that insert a disk to g drive, and the computer is ejecting that disk. when i try with another cds or dvds it works properly
View 3 Replies View RelatedI'm trying to set up windows 7 so I can access it remotely from my iPad.Ive set up windows 7 to allow remote access. I've tried disabling avg and windows firewall but I still keep getting connection refused.
View 3 Replies View RelatedHere is what is going on. I plug in the MP3 player, does not matter which port, and when I go to "My Computer" to click on the drive to get the music files it comes up with error message "G: is not accessible. Access denied."
I have tried going to properties and configuring security options, but there is nothing with "security" or related to that. I am already logged in as Admin, there is also no "run as admin" either.
Using Win 7 Pro on Dell Latitude D630. I joined my domain and completed all Windows updates. I can access internet as long as I am logged in as administrator,but when logging into the domain as any other user, IE9 remains when blank.I have switched from a static ip address, to a received DHCP address but to no avail.
View 1 Replies View RelatedI have a clients harddrive (XP Home) to extract their data.I just got a Win 7 laptop for servicing computers and discovered I bought a nightmare.I cannot set sharing access to the clients drive in order to extract their files.Any ideas on accessing other drives from Win 7?I have connected this one by USB and even cloned it to empty space on my Win 7 drive.I have been through advanced sharing at the root and every folder I can get to.
View 1 Replies View Relatedi heard that when you delete a file, it actually puts it into a hidden folder in the recycle bin. i enabled the visibility of hidden folders, but i did not see it there.where else could it be?
View 9 Replies View RelatedMy laptop started randomly shutting down a while ago but only when i play a game, but if i have both of my 3d modeling programs, itunes, chrome, and other programs running the computer would run fine for hours on end. A couple days ago the laptop did its usual random shutdown. so i started it back up and the mouse wouldnt work. so after opening it up and reconneting the cable to the board the computer wont boot. It'll get to the starting windows screen but after a minute or two it show a blue screen for about a fraction of a second then restart. It'll keep doing that till i uplug it and take the battery out. I cant start in any of the safe mode options, i cant launch windows repair. Im not able to use a recovery disc cuz the laptop didnt come with one. I basically cant do anything. Now the computer will shut down randomly again but during startup, but the laptop is still cold. So now i decided to take out the hardrive hoping to either save the files or most of them at least or to find the cause of my problem and fixing it. After i hook the hard drive up to my desktop via SATA cable it shows up in My Computer as System Reserved and Local Disk (F: ) but i cant access local disk but i can access system reserve. At the top of the explorer i just get a green bar that never reaches the end and when i click on local disk the explorer becomes unresponsive and what not.
I open devices and printers and it read the hard drive as usb storage so i checked device manager and it recongizes it as a Hitachi Hard Disk. When i click on disk management Nothing happens besides at the bottom it says " Connecting to Virtual Disk Service" for an extreme amount of time. I also tried booting the hard drive on the desktop but it goes through the same proccess as it did on the laptop and i also cant do anything.
I have a desktop (Using it right now) with a hard drive, 7 etc etc and everything works fine. I am however having issues accessing a hard drive from an old lap top I used to own. It was sold, but I kept the hard drive. This was a while ago so I can't remember its OS, but I'm pretty sure it was XP but possibly vista. I have plugged it into one of my towers extra hard drive spots in hopes of being able to retrieve some old pictures from it.This is my problem: After reboot, it got a message saying the usual installing device driver software thing, after that... nothing. I look in my computer and no new drive showed up.
View 1 Replies View RelatedI have installed newly a windows 7 in my pc that it eaither have windows 8 installed in when i boot manage screen is showing only os that i can see is windows 7,i already installed easybcd but it also do not show me windows 8 and actually i do not can boot my windows 8 and use it what can i do?
View 1 Replies View RelatedI have a problem with Windows 7 and the c drive. I will try to explain a little bit the situation: have a Dell xps l501x with a home edition windows 7 licence.Since I prefer to use linux, I resized the Windows7 and create another partition for the linux distribution when I bought. So I had Windows 7 and linux (arch linux) working together for some months.I barely used Windows 7 so I decided to use virtualbox to use windows7 (the raw device as a harddrive). And here started the problems, because I ended with a black screen and the mouse pointer in windows7 (the probably was due to a resolution problem)After many months (as I said, I barely used it), yesterday I decided to fix the problem and I managed to do it. But now I have another problem that I don't know how to fix it (I'm not using virtualbox anymore).
When I start windows 7, the wallpaper is black with the infamous "compilation 7600" and many advice that "is not a genuine copy" (actually it is), and a lot of errors at start. Trying to use the OS:- Many application don't work. Even diskmgmt.msc doesn't work.- I can't access C drive, if I tried prompts an error about permissions, even if I change the permissions I can't access. And If I try to see the properties all the values in the c drive are "0 bytes" (size, free space...)Regarding that, I can't download anything.It seem the c drive is not recognized and I suppose that is the main problem.If I boot with the option "Directory Services Restore Mode" I can acces to C and everything seems to work better. And in the properties the values are correct (the size, free space....)
When using XP and Outlook 7 we were able to create a new email, click the attach button and in the File Name section type http://intranet. This would give us access to the intranet page and the various folders and documents that needed to be emailed to customers.
When using Windows 7 Ultimate or Professional following the above steps will only put a link to the intranet site in as the attachment.
How do I go about replicating the XP way of accessing files on the intranet?