I just need your expert opinion on this matter before I call Dell back. Apparently my Hard drive went out on my new computer (6 mos.old) and, I guess a possible Motherboard problem as well, because the Dell tech told me they were sending a Hard drive & a motherboard to a service tech near me. Anyway, the tech came out with only the Hard drive. When I ask him where the Motherboard was, he didn't know anything about a motherboard.Dell did not send him one. He went ahead and installed the Hard drive & every thing seems to be working fine now for 4 days so far. My concern is, do you think my computer would still work ok if it has a faulty motherboard too? My warranty will be up in about 6 months & just want to make sure. I have a message to call Dell back & let them know how my service call went, but Just wanted your opinion before I do. Should I insist on a new motherboard?
I was wondering, if I got a new 500gb internal drive cause my old one is bad, would I be able to transfer everything (Including my seven install) onto the new drive? and if yes, how would I go about doing so?
In my 8 years of serious computing, I have never had to replace a HDD but I am going to have to do it for the first time sometime earlier next week when the new one along with the recovery media from Acer gets here.I have managed to locate a service manual for my Acer Notebook model series here.The new HDD is a WD500BPKT @ 7200RPM The old HDD is a WD3200BEVT-22ZCT0 @ 5400RPM Will I need to install new drivers (SCSI etc.) or anything else, or is it a simple plug-and-play operation once the recovery media is booted off of the disks and installed?I suspect I will need to change the BIOS Boot Order so that the opticle drive is first rather than IDE 0 to get the disks to come up, so that's a non-issue.
alright, I'm posting on behalf of a friend(doing chat on facebook..), who is trying to replace the harddrive on a windows 7 laptop.now.. installation of the new drive did not go to plan, so he tried to put the old one in, and the computer apparently took this as cause to commit seppeku if you will.we have tried everything, up to and including testing for a bad mobo, which I suspect it is.all he's getting is a power light, not even the screen's backlight is coming up.
My Dell 1525 Windows 7 laptop had begun to experience more and more frequent hard drive errors. So, in an effort to fend off total disaster, I purchased a new hard drive. The new drive was slightly larger than the old one (250GB vs 160GB). With a week old backup in hand, I used Acronis to do a disk CLONE to the new drive in an external enclosure. I was able to do it without any apparent drive errors. I then swapped drive for drive and rebooted. My most frequent apps worked fine, network access was fine, etc. Then I went to do a Windows Update - not fine. The little shield in the upper left corner of the box was red and, when I clicked on the "Check for Updates" box, it replied Windows Update cannot check for updates because the service is not running. You may need to restart your computer." I went to Services, started the service, marked it Automatic, and tried again - no joy. So, as it suggested, I rebooted. No joy again. After trying a couple of different backup versions with the same result. I went back to square one and used the original Windows 7 install disk. The install went fine and I was able to use Windows Update successfully. I hoped that having verified that a vanilla Windows 7 worked, I might be lucky enough to just be able to restore my latest backup. Wrong. The system appears to work fine with the only KNOWN problem being Update - there may be other problems, as yet unknown. Differences I am aware of: new hardware partitions proportionally larger than the previous disk.
last weekend I was trying to recover the contents of a failed hard drive to a new hard drive using Windows System Repair Disc and Windows System Image.was able to successfully restore the image. Everything is working fine, but here is my question - the original hard drive was 750 GB and the new one is 1TB. After doing the system restore the hard drive properties show the identical size of the failed drive - not the new larger size. The BIOS shows the correct size. Does the Windows System Image set up the new hard drive exactly as the old one, so it will only access the original 750 GB
I replaced a Dell battery with a non-Dell one in a Vostro 1720, under Windows 7. The battery powered the laptop until the manufacturer's charge (as recommended) discharged. It recharged to 10% but no further (perhaps I imagined this and it just did not discharge fully). At boot-up, the message 'Windows cannot identify the battery' comes up. This is the same message that came up when the old dead (and broken) battery was in place. I cannot find any way of managing the battery by software (this is probably a Windows 7 problem - it was possible under Vista, I think). I think that Windows 7 is just refusing to 'identify' the battery. I've tried all the permutations of mains-power/battery connection/disconnection.
I had Dell XPS 8300 Desktop & had bought & Installed Windows-7 ( Ultimate ) on it's 500 GB HDD.I gave that system to my relative except Hard Drive.Now I bought Dell T-7500 Workstation with only DOS installed on it's hard drive to save some money & because I already have Windows-7 ( Ultimate ) DVD.I took out the hard drive with DOS from the workstation & replaced it with the hard drive that I had in XPS with Win-7 already installed.I then tried to boot it in the workstation but it wouldn't boot & gave error messages.So I formatted the OS Partition & fresh installed Windows-7. Now it does load Windows -7 but first it goes thru some other commands as follows when I start the system.
Dell SAS 6 Host Bus Adapter BIOS MPTBIOS 6.22.03.00 ( 2008.08.06 ) Initializing..... Press Ctrl - C to run SAS Configuration Utility Searching for Devices at HBA 0..... Dell MPT Boot ROM Successfully installed
Then it loads Windows-7.All of above happens on its own, I didnt touch anything.So what is going on & what do I have to do get rid off those initializing commands ? I have never had this happen to any previously owned Dell systems.Also I haven't installed any drivers yet but Sound, Video & Internet does work.Do I need to install any drivers & if yes, which ones ?Here is the configuration of Dell workstation T-7500 :
Intel(R) Xeon(R) E5645 2.40GHz, 12M cache, 5.86 GT/s QPI, Turbo, HT, 6C Intel(R) 5520 Chipset DOS Factory Installed (English) Integrated Intel(R) SATA 3.0Gb/s controller with support for RAID Integrated High Definition Audio
Got a new computer today, plugged in my old 500GB hard drive for back up storage. I went into it, can see everything fine, go through the program files, etc...Except I can't find my old documents, pictures, or anything that was saved on my desktop. A search won't even bring it up. How the heck can I get it back?
The hard drive in my friends Dell Inspiron 15R (M501R/M5010) needs to be replaced. I have access to an older HP pavillion hard drive with identical specs (SATA, 5400 rpm, 9.4mm/70mm, etc.). Before I spend a few hours taking apart the inspiron to get to the hard drive which is not easily accessible, I want to make sure the two hard drives are interchangeable, and that there won't be any HP vs. Dell compatibility issues.
Since there is no cd/dvd drive in a Dell Inspiron Duo1090, how is the OS reinstalled. Can it be done from a USB Drive? An external CD/DVD reader? Does the new drive need to be set up via USB from another computer? Does the DUO have to go back to Dell?
I'm looking at getting an external storage device to store my files on, and I can't decide what to get.Is there a massive difference between between an external hardrive, and a Desktop hard drive? These are the ones I can't decide from..Western Digital 1TB Elements External Hard Drive | Littlewoods.com..Is there much difference between the two? Which one would suit me better? I'm running a samsung rv510 laptop.
Trying to figure out what is involved in changing hard drives in a new Atg 6420 laptop. Im guessing I need to create a ghost image of current HD, but not sure how to. Once that's done do you just install new HD and reinstall ghost. It doesn't seem like it should be that difficult.
I have a dell inspirion 1505. I just upgraded my Ram and my hard drive. My computer came with a 80GB hard drive, but when i tried to replace it with a new 500GB hard drive my computer still only recognizes it as a 80GB. During the windows 7 upgrade where i would normally be able to clear my new hard drive and specify my new drives it still only showed 80 GB.
i have talked to dell twice now and i get conflicting answers each time. The first person said that my computer would only support 120GB and the second said it would only support 100GB. I have a hard time believing this because my computer came with a SATA harddrive, which shouldnt limit me.. At least i thought.
my desktop computer won't boot. When I turn it on it displays the welcome splash screen and then goes black. A message will then display that says CMD failed to start and then it will shut down. It does the same thing in safe mode as well.My question is. I have already set up the HD from the desktop as an external to my laptop so I could get files off it. Is there any way to do system restore on the hard drive when it is set as an external? Because I did this last night and I think if I restore the drive it will fix it.
I have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
So, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?
I have a HP Touchsmart IQ500. Turning my computer PC on today, all I got was a blue HP invent screen with setup, boot menu, system recovery, and system diagnosis, and I could not get past it. I entered the BIOS and figured out that the hard drive was listed as "not installed." Pretty sure that is the main problem.I tried a system restore (with the Windows 7 install disc), but I guess the computer couldn't read the hard drive enough to enter safe mode (I tried restarting and F8ing several times). I put in an external hard drive, and the BIOS read it; however, windows does not allow you to partition an OS on a hard drive.
I have an internal hard disk not in use ,and I would like to make it as external disk !I looked on the net and I found I should have the " encelsure " butt I think I wont find it here in my city .So is there another way ? like usb -esata cable
Me and my brother built me a new computer from scratch (he did the building - i did the watching). I purchased an internal hard drive from Overclockers UK. It's a Samsung 1TB drive. I also have a 64 Solid-state drive in there as my primary hard drive that Windows was installed on and a couple of programs are installed on. My storage disk (the 1TB disk) is for all my music/films etc. Whenever I drag and drop a file into the Samsung hard-drive - it copies it rather than moves it instantly.When I had a laptop, I had 3 external hard drives and this is the way it copied files onto them.how I can get the internal drive to stop acting like an external drive?
I have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
I have a USB Webcam 6.1.7601.17514 from Microsoft installed on a Fujitsu Laptop (Windows 7 ) and I want to copy and install it on another Fujitsu laptop (Windows 7).The other laptop the camera is not working and there is no webcam driver installed.
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
I cannot find my windows 7 dvd, I am thinking that one of my little ones was playing in the office and threw it away or hid it somewhere. . I have the product key but no dvd. Is there a way get a replacement dvd and just use the key that i have. I really dont want to spend the $300 that i spent for the full ultimate edition.
My HP p6710f came with �PDF Complete� which lets you save a single page of a PDF as its own PDF file. This option comes up when you right click on a PDF and choose Print & then the printer, which is PDF Complete.However I did not know this was a trial program & mine just ran out. Every month I generate a PDF with several pages, but each page is for a different person. I found it convenient to print or save each person�s page separately in order to email to them.
I need a replacement for PDF Complete & was hoping to find something which has the same functions. I have seem some free programs for creating PDF files but am unable to figure out if they can save individual pages as new PDFs.
