DHCP Client Service Fails To Start (Error 1075)
Jul 13, 2012
On July 12th 2012, my computer installed updates. After rebooting and waiting for me on the login screen, I gave it a hard shutdown to check on the BIOS settings (for a little side project, in the end I did not save any changes). After booting and logging in again, I find that many services are not running. I ran a very thorough check for malware and viruses (took over 24 hours to complete), and still no solutions. I have uninstalled/reinstalled my Broadcom 802.11g Wireless Driver several times.
I now look in the Event Viewer and find that the DHCP Client service is not running! It is set to automatic start in Services.msc, but when I try to manually start it, it gives me error 1075 (some dependencies do not exist or are marked for deletion). Running ipconfig, I notice that my system is using an APIPA-formatted address (169.254.x.x), indicating that the computer couldn't find a DHCP server.
My Event Viewer is peppered with:
Event 7003, Service Control Manager
The DHCP Client service depends the following service: Afd. This service might not be installed.
Event 7001, Service Control Manager
The WinHTTP Web Proxy Auto-Discovery Service service depends on the DHCP CLient service which failed to start because of the following error: The dependcy service does not exist or has been marekd for deletion.
And that keeps repeating many times in a minute (about 30-40 cycles of it).
View 6 Replies
ADVERTISEMENT
Nov 2, 2011
Last week I hit an issue whereby I was unable to access the Internet wirelessly even though my laptop could see the router and had a good signal. I tried connecting up via an ethernet cable to no avail.
The issue seems to have started right after a Windows Update but I can't be 100% certain. If I do ipconfig /all I can see that DHCP is not enabled. I know the router is fine because my vista laptop can access wirelessly via the router fine. I tried doing some things I seen in the forum such as ipconfig /renew etc. but it said it couldn't contact the RPC server. I followed this up and was recommended to check the DHCP client service was started. It isn't even there. I was wondering if the update could have removed it.
Someone else who had reported the same issue on this forum was asked to do a system restore. I did this and the service is still not there. I am assuming that the non-existence of the DHCP client is the cause of my issues accessing the Internet.
View 1 Replies
View Related
Sep 11, 2010
I have network sharing issues and I believe the problem is that I cannot turn on file/printer sharing. When I click the button under advance sharing settings for file/printer and hit save (as an admin) it just goes back to off. Under Services, the Server option which is on automatic does not start. When I try to start it, it says:Windows could not start the Server service on Local Computer. Error 1075: The dependency service does not exist or has been marked for deletion.
View 5 Replies
View Related
Jan 8, 2013
I have a program running that automatically syncs some of my data online. It is running on a computer with Windows 7 Pro as well as a Windows Server 2003 that I use as for file storage. Unfortunately it does not startup until I log into a profile, but since I don't really use these computers, sometimes this doesn't happen for days on end. I decided to create it as a service (used the sc.exe utility - sc create DataBackup binPath= "C:Program FilesData Deposit Boxackup.exe" DisplayName= "Kineticd Backup" start=auto). The service was created successfully, but when I try to start the service, I get the following error.
Error 1053: The service did not respond to the start or control request in a timely fashion
View 2 Replies
View Related
Sep 28, 2012
helping a friend fixing his Internet access on his Windows 7 machine.The machine was previously on a wired connection, and was working fine for 2 years.But the machine was moved, and an USB wifi dongle was purchased. And now he can't get online.Started debugging with disabling IPv6 on the connection. Diasbles firewall. Uninstalled two antivirus programs. No luck.Then tried to reset the TCP/IP stack with: netsh winsock reset catalog and netsh int ip reset reset.logThe I came over this post, and followed all the steps in flyguy747's answer. Still no luck.I downloaded and ran Farbar service scanner, but could not find any MD5 error on any of dll's.what i should try next?
Farbar log:Farbar Service Scanner Version: 19-09-2012
Ran by Jentutten (administrator) on 27-09-2012 at 21:24:10
Running from "C:\Ny mappe"
Microsoft Windows 7 Home Premium Service Pack 1 (X64)
[code]....
View 5 Replies
View Related
Jun 9, 2011
I am having trouble installing sp1 despite other windows updates having been flawless so far. I tried following instructions found at the Windows site but the System Update Readiness Tool didn't find any errors and repair installation aborts. Sorry to bother you with another "sp1 fail" thread but I have exhausted my search options for solution here and in other sites, which makes this request for help my last resort.
View 5 Replies
View Related
Nov 28, 2012
I was looking over the menus in my router (SBG6580) config page. As of right now I have my netbook and iPhone connected. I found a laptop listed that I do not have:
00:24:2b:bb:6d:d3192.168.000.004255.255.255.000D:00 H:01 M:00 S:00Fri Dec 13 20:45:53 1901 laptop
I selected it and deleted it. Where did it come from. Should I change my router/wireless password?
View 1 Replies
View Related
Jan 19, 2011
Probably this error is pretty much a non-issue and I haven't a clue if the affected W7P machine, even runs Windows Server 2008 R2 (or any windows server for that matter).Is this 'server' thing, software that is by default installed (and I'm guessing it's only used when the machine networks with another machine, home/work groups)?As for if and what version the W7P machine even 'runs', the only loosely provided instructions I've found (by clicking the event log's link to information about the error), results in a webpage... Event ID 1001 ..which sort of implies to me that the W7P machine might be running 'Windows Server 2008 R2', if only because the event log error report's link led me to that web page's article, ie; the article says it applies to Windows Server 2008 R2.I tried following the article's mentions of checking to see what version of 'server' that is installed, but step 2 seems too poorly written for me to follow what's actually be said...Determine if there is a network connectivity problem To determine if there is a network connectivity problem between the‚ DHCP‚ server and domain controller: At the DHCP server, click Start, click Run, type cmd, and then click OK. At the command prompt, type ping server_FQDN, where server_FQDN is the fully qualified domain name (FQDN) of the domain controller (for example, server1.contoso.com), and then press ENTER. What's unclear to me is where it alludes to..."..where server_FQDN is the fully qualified domain name (FQDN) of the domain controller"...I see the article provides an example, but the example seems as obscure as it's parent reference.How does a user determine the "fully qualified domain name (FQDN) of the domain controller"?If that obscurity isn't bad enough, the article then lists a second step "1" stating..."At the command prompt, type ping IP_address, where IP_address is the IP address of the domain controller, and then press ENTER."..and again I haven't a clue as to what's being said, ie; we're not born with a 'domain controller's IP address' tattooed on our forehead, so how's that detail determined?Further down in the article, it lists a step 4 stating..."Type ping IP_address, where IP_address is the IP address assigned to the computer. If you can ping the localhost address but not the local address, there may be an issue with the routing table or with the network adapter driver. " ..and step 5 states..."Type ping DNS_server, where DNS_server is the IP address assigned to the DNS server. If there is more than one DNS server on your network, you should ping each one. If you cannot ping the DNS servers, this indicates a potential problem with the DNS servers, or with the network between the computer and the DNS servers."..and as the article doesn't detail how to determine the machine's 'IP Address' and doesn't detail how to determine 'P address assigned to the DNS server', again I'm left reading an otherwise virtually useless article.
View 2 Replies
View Related
Oct 25, 2011
I have a problem with a Windows 7 64 bits. After power on, the DHCP client tries to acquire an IP for all the network cards, even those that are not connected.I can see in the event logs that after 2 minutes from the startup, I get one message for each interfaceQuote: >Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0xMAC_ADDRESS. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server." I have an Astaro VPN client that manifests itself as a network card and when I start it up (manually) it fails to receive an IP from the DHCP server. I believe it is related with this general DHCP problem because if I start it up within two minutes from power on (before I get the message in the event log), then it works.
View 1 Replies
View Related
Dec 31, 2011
I'm using windows7 enterprise edition on my Laptop. Accidentally I have removed most of the files inside ProgramData folder.
Now issue is that, DHCP Client Service is not working.
(1) Does DHCP Client really Depends upon any file there?
(2) I have seen that some of the folder have been created inside ProgramData. Can I copy any folder/file from other Laptop (Win7 EE) to my laptop to make this work?
View 5 Replies
View Related
May 7, 2012
I have tried to install this update six times today (07/05/12) after it was flagged as an important update this morning. Looking at my update history it also failed to instal on the 18th October last year but it has not bothered me since and i have not noticed it until now. Of the seven attempts I had the following error codes from earliest to latest : 800B0100, 80246007, 80010108, 8024200D, 8024200D, 8024200D, 8024200D. I have followed advice from MS running KB947821 and FIX IT also disabled my Norton 360 firewalls and auto protect but to no avail. Also I do not have a DVD with Windows 7 as it was not supplied with my PC and I don't want to restore my computer and lose all my installed software.
View 3 Replies
View Related
Jul 8, 2011
solving Error #1075 problem in conjunction with CheckPoint VPN NGX R60 HFA3. I am using a Dell E6510 laptop computer running Windows 7 Ultimate 32-bit OS. I can get this VPN to run and connect when I use Microsoft's XP virtual machine sitting on the Windows 7 desktop but I cannot get it to run on the Windows 7 desktop by itself.Although the VPN seems to load without incident the associated icon "key" does not appear in the notification tray at the lower right. It does appear in the XP virtual machine and on a separate HP desk top running Vista.When I type services.msc at the Win 7 command prompt I get a list of all the loaded services including the CheckPoint VPN. It is at this point when I try to start the VPN I get the 1075 error. When I check the dependencies under the VPN I find the "CheckPoint Office Mode Module" and the "VPN-1 Module".How do I determine if these dependencies are causing the 1075 error message? What steps do I need to take to resolve the error message so the VPN will start?
View 1 Replies
View Related
Jan 12, 2012
I recently built a new computer and on occasion when I turn the computer on, I'll get a blue screen saying windows failed to load type thing, and then it restarts and i have to recover. Now the weird thing is it doesn't happen all the time It more often than not doesn't work, but still there will be times where it works all day. I can't figure out why it works sometimes and not others. I don't do anything different, just facebook and Star Wars the Old Republic, so I don't think its a program which is causing the issue. Anyway here are my comp specs and the problem details:
Intel i5 2500 3.30GHz
Gigabyte GTX560OC
C/Master Extreme 700W
WD 1TB Black
Gigabyte GA-Z68AP-D3
LG DWDRW
8GB of RAM
Now the problem
Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.2.1.0.768.3
Locale ID: 3081
Additional information about the problem:
BCCode: 6b
BCP1: 0000000000000000
BCP2: 0000000000000000
BCP3: 0000000000000000
BCP4: 0000000000000000
OS Version: 6_1_7601
Service Pack: 1_0
Product: 768_1
View 9 Replies
View Related
Jul 19, 2012
I am currently running Windows 7 Ultimate x64 and one morning, my audio stopped working. I discovered audio stopped working because the Windows Audio Service, which relied on the Windows Audio Endpoint Builder service, which relied on the Power service, all stopped working. So to solve my audio problems, I must first start the Power service.However when I try to start it, it gives the following message:Windows could not start the Power service on Local Computer.Error 127: The specified procedure could not be found.
View 3 Replies
View Related
Nov 22, 2012
Below error has been keep popping in Windows 7 Event Viewer whenever I bootup my system, I had even format my system drive and it still happening.I also have observed that now my PC took a little while more to load.The WinRing0_1_2_0 service failed to start due to the following error:The system cannot find the file specified.Attached is the screenshot of the error.
View 14 Replies
View Related
Jan 15, 2013
I have created a service using the following command in cmd prompt:sc \computername create servicename binpath= C:WindowsSystem32sam.exeThen in the service list, I could see my service.When I right clicked on the service and clicked on Start , I am getting a pop-up with the following error: Windows could not start the newservice4 service on Local Computer.Error 1053: The service did not respond to the start or control request in a timely fashion.
View 2 Replies
View Related
Feb 2, 2013
I am getting an error message which states:ERROR: unable to start the Bluetooth Stack Service. How do I fix this?
View 1 Replies
View Related
Jun 27, 2012
I recently got a virus on my PC and managed to get rid of it. I was using TDSS killer and it somehow removed my svchost.exe -k netsvrs file from registry and I am almost positive this is why I cannot start it. Although I do not know how to fix it. I am running windows 7 ultimate x64.
View 6 Replies
View Related
Jan 20, 2012
I keep getting this box telling me "Error:unable to start blue tooth stack service".Also unable to open certain Web pages.
View 4 Replies
View Related
Jan 12, 2013
I finally got a new laptop after almost a year of struggling with my old one. I've had experience with using homegroup in the past and was thinking maybe I could access some of my files on my old laptop through that so I don't have to go through the trouble of manually transferring everything via flash drive and what not. I seem to be running into a problem though, my old laptop seems to be in its own homegroup I guess. Whenever I try to leave it, it says "windows cannot remove the computer from the homegroup".
I researched the problem, and used the troubleshooter which said that the homegroup provider service wasn't started and it couldn't be fixed automatically. I tried restarting starting the service but got that error 1608 thing. To bypass this I've tried joining whichever group my old laptop is in, but it can't seem to be found even though the two are both on the same wifi/network. If it matters, the new laptop is windows 8 and the one I'm having trouble with is windows 7.
View 5 Replies
View Related
Feb 2, 2013
WLAN AutoConfig service gives error 1067 when trying to start it. What I've tried:
Reset winsock settings
Ran SFC /scannow
Did system restore
Uninstalled and reinstalled drivers
I tried all of these in normal mode AND in safe mode. None of it worked. Then i thought the service dll (C:Windowssystem32wlansvc.dll) itself might have been damaged/outdated, so I decided to delete it and put a new one from donor pc. NOPE.It wouldn't give me access to the file. No matter what i tried, safe mode, unlocker tools, auto rename it on startup, doing everything in administrator or even messing with permissions under file properties. It just wouldn't give me access to the file.Wi-Fi was working smoothly few days ago and i literally have no idea why it stopped working.
Specs:
Windows 7 Professional 32-bit
Sony VAIO VGN-SZ340P
3945ABG Wi-Fi card
View 4 Replies
View Related
May 31, 2010
I have a sony vaio laptop when i start up my computer i get " ERROR unable to start the Bluetooth stack service" what is this?
View 3 Replies
View Related
Nov 30, 2012
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i3-2350M CPU @ 2.30GHz, Intel64 Family 6 Model 42 Stepping 7
Processor Count: 4
RAM: 6037 Mb
Graphics Card: Intel(R) HD Graphics 3000, -1988 Mb
Hard Drives: C: Total - 454779 MB, Free - 395876 MB; D: Total - 21855 MB, Free - 2354 MB;
Motherboard: Hewlett-Packard, 1819
Antivirus: Norton Internet Security, Updated and Enabled
Printer HP Photosmart 5514 B111h / Network Status: Ready / Active Connection Type: Wireless
error 1053: The service did not respond to the start or control request in a timley fashion Also before a message / Windows cannot connect to the printer. The local print spooler service is not running. Please restart the spooler or restart the machine. Does this mean to connect a USB cable and reconfigure the wireless connection.
View 3 Replies
View Related
Sep 5, 2011
I have the problem that the service WLAN Auto-Config isn't started. When I try to start the service manual then the error 1068 appear: "Error 1068: The dependency service or group failed to start." I have tried the three steps of onopko, but this is not working to my computer. On advice of StalkeR I have add the reg files of Black Viper site as Safe as well default. Every time I have restarted my computer after adding the reg files, but both files are resolving me problem.
View 1 Replies
View Related
Aug 12, 2012
I am unable to connect to the Internet on wireless home network.I have carried out the following:'Click Start, type services.msc, then press Enter. Scroll down to "WLAN AutoConfig" and right click on it and select Properties. Set it to Automatic and not Disabled, and press the Start button, then click OK.That should start the service.'I received the following message:"Windows could not start Wired AutoConfig Service on local computer.Error 1068: The dependency service or group failed to start."
View 1 Replies
View Related
Oct 6, 2011
I have a Dell XPS M1730 with Windows 7 Ultimate and it was doing an iTunes update and the lid got closed during the update process. Now when I start the computer up it says "the user profile service service failed the login, user profile cannot be loaded". The computer starts up in safe mode and won't let me do a system restore because it says it is shut off.When I look at User Profiles in Windows 7, it states that the users profile is as backup and the default profile is the local profile. How can I fix my computer to get my user profile back up and working?
View 1 Replies
View Related
Dec 4, 2010
How did it get activated? Do I need it? If not, how do I get rid of it? I have never heard of it before.This is a single user computer. No Homegrouping.Asus G72 Gamer's Notebook Windows 7 Home Premium 64 Bit?
View 4 Replies
View Related
Oct 3, 2011
I started to install a home network, but was interrupted. Now Windows 7 will not complete its startup except to say "access is denied." I did not start a recovery point before, hoping to get all the updates, etc. on before needing recovery. Is there any way to fix the problem without reloading everything?
View 9 Replies
View Related
Nov 19, 2012
Someone out there please help me. I've been working on this problem for like 6 hrs.Failed to connect, "Group Policy Client Service" windows 7. Failed to Connect with "Group Policy Client Service".I copied the message and saved it as an image. I also ran dds and attach report.
View 14 Replies
View Related
Oct 3, 2011
I've recently restored my Windows 7 Home Premium 64bit OS on to a new SSD using Macrium Reflect. My hosts file has always contained entries for local websites and has always worked until now. After much hair pulling and reading of forums, the only way that I could get the DNS Client to read and process the hosts file was by adding the "NETWORK SERVICE" user permission to it. It already had "SYSTEM", "Administrators" and "Users" (my user account). This was never required before, so I'm confused as to what has happened to require it now?
View 2 Replies
View Related
Feb 20, 2013
I have been refused acccess to my laptop, message reads, The Group Policy Client Service failed the logon. Access denied. I am entering the correct password but i cannot log on
View 1 Replies
View Related
