Concept Of Soft Bad Sectors?

Aug 30, 2012

I am not able to understand the concept of "Soft" bad sectors. Can software be the cause of bad sectors?

View 1 Replies


ADVERTISEMENT

Does Windows 7 Have A Soft-Restart Function The Way 98/XP Did

Dec 10, 2012

As I'm sure many of you already know, older Windows versions 95/98/XP had a way of soft-rebooting Windows; it essentially allowed you to reboot the system without actually turning the machine off.

In the older versions, I believe you just held the shift button down after clicking Restart until it rebooted back to desktop without turning the mechanical parts off completely.

Does Win7 have a function like this? Or does there exist at least some kind of workaround for all the reboots required during software install/Uninstall?

View 2 Replies View Related

Soft Ap With ICS (no Connectify No Virtual Router)

Jun 6, 2011

anyone know of a soft AP with ICS?

View 1 Replies View Related

Shrew Soft VPN With RV042 In Windows 7(64)?

Dec 19, 2009

I can't get Shrew to work with my RV042 in Windows 7 (64-bit). All computers are using Windows 7 Professional. Here's the rest:

Shrew Version 2.1.5
Firmware 1.3.12.19-tm
Firewall disabled
Multicast Pass Through enabled
IKE with preshared key
VPN Pass Through enabled

Shrew hangs on "bringing up tunnel," right after preshared key configured.The debug log states that IKE packet gets sent with no response, and negotiation times out.

View 3 Replies View Related

Constant Soft Hangs, Freezes, No BSOD?

Jun 8, 2012

I just did some upgrades to my pc. Here are the current specs:

Motherboard: Crosshair V
CPU: AMD FX 6100
GPU: eVGA GTX 680 HC
RAM: 4x4GB Ballistix Tactical Tracer
PSU: Corsair 750Watt
OS: Windows 7 x64 Clean Install
HD: WDC-WD2500KS-00MJB0

Like it says above, this is a clean install. I have tested the RAM with Memtest86+ for 8 hours and found no errors. I have tested the HD with Seatools and found no errors. I have run Prime95 for hours without errors. I water cool my CPU and GPU and temps max at 37C.The OS constantly hangs, freezes, or whatever its called NONSTOP. Most of the time I'm able to move the mouse but can't DO anything with it. Eventually (within minutes) it comes back to life and does everything I'd been trying to do while it was frozen. I don't get much time inbetween freezes (a minute max between freezes). I've reinstalled the OS several times and no joy. At first I thought it was a bad motherboard, so I RMA'd it and it is still having the same issue. These freezes began happening well before video drivers were even installed (or any other drivers for that matter). It even does the same thing in SAFE MODE.from the EVENT VIEWER:

In the last hour: 19 Service Control Manager Error 7001
In the last hour: 44 amd_sata Warning 129 (this one always comes in pairs and always 30 seconds apart)
In the last hour: 169 Service Control Manager Information 7036

View 9 Replies View Related

Intel D-865 Video Driver Soft For Windows 7 OS?

Oct 9, 2011

Is the intel provide the graphic driver for the D865GSA Board for windows seven if provide then give me thread that from where i download these drivers. information about these drivers.Beacause i want to play games like Need for Speed games on the windows 7.

View 2 Replies View Related

Dvb Card Doesn't Work After Worked With Com Port In Other Soft?

Jan 7, 2013

I have a USB DVB card that works good! 3 days ago I have working on virtual com ports in matlab soft! and after that when I connect dvb card to my laptop usb ports the dvb software doesn't detect dvb card! and shows this message: all capable dvb adapters are busyno free device has been found after that I try to reinstall matlab and dvb soft and dvb driver too, but it hasn't work yet

View 6 Replies View Related

Shrew Soft Vpn Win 7 Compatibility Cisco Checkpoint VPN Client

Feb 26, 2010

I would like to know if Shrewsoft VPN Client can be installed on Windows 7 (32 Bit) with Checkpoint & Cisco Clients already installed. I have both Checkpoint & Cisco Clients installed on Windows 7, with the respective services set to manual, and both clients are co-existing without any problem. Since I also support Juniper SSG boxes, and since Juniper has NOT YET come out with a client which supports Windows 7, I was wondering if I can use Shrewsoft client instead (which is reported to work fine with Juniper SSG).

Previously I had Vista on which all the 3 - namely Checkpoint, Cisco & Juniper (SafeNet) clients were working beautifully. But Vista being Vista, I had no choice but to upgrade to Windows 7.

View 2 Replies View Related

To Fix Bad Sectors Of Hdd

Jun 20, 2011

What features of 7 helps to repair bad sectors of hdd

View 2 Replies View Related

Format HD With Too Many Bad Sectors?

Jan 16, 2013

This notebook started to behave badly and I found that the problem is the HDD.ItFor you to get the scenario: I first ran the Windows native disk tool and it reported no problem. But the system was still slow and freezing.So I made some googling and ran Check Disk GUI, but it couldn't complete its job. So I started to figure out that the thing was a bit harder than I first thought.I tried to defrag and optimize with Auslogics Disk Defrag Portable, and it too couldn't go all the way.I tried PartitionGuru, which, finally, could do the job � in more than 48 hours of disk scan! And it reported: "Disk verify completed. 548 bad track areas found."After all that, things went worse: I couldn't start Windows, I got a "Missing operating system" message...Then I tried Wondershare LiveBoot 2012 to no avail.The last effort I want to try is use some portable app (running from a USB pen drive) to format the whole HDD.The HDD in question has three partitions. C: (system), D: (data, I created this partition), and a hidden one that keeps the data needed to restore the Acer notebook to its factory settings.If I succeed to format the whole thing, I'll try to make a fresh install of Windows 7 Home Premium. I want to format the whole HDD (from a USB pen drive) to have one single partition.

View 4 Replies View Related

Chkdsk /v 8kb In Bad Sectors?

Feb 23, 2012

I made a chkdsk and found errors which were repaired by not allowing the bad fragments to be written on. When I use chkdsk /v it continually shows 8kb in bad sectors. Does anyone know if these are the bad sectors that were sent into limbo or the total bad kb on the hard drive? I have made back ups of my documents and the OS. I think that these bad sectors were caused by a recent freeze which required a bad shutdown. If so I may not be required to replace the harddrive.

View 4 Replies View Related

Bad Sectors In Flash Drive?

Aug 7, 2012

explicitly creating bad sectors in a flash drive. Is making bad sectors possible by repeadly disconnecting flash drive during file write process? How can a flash drive develop bad sectors in its memory ?

View 6 Replies View Related

Windows 7 Won't Load Due To Bad Sectors On Hdd

Nov 8, 2012

My Windows 7 system will not boot due to what I found out are bad sectors on the hard drive. I ran SeaTools to check the Seagate drive and it found several bad sectors. If I allow SeaTools to "repair" the bad sectors, will I be able to boot into Windows 7 again so I can at least save my data before replacing the hard drive?

View 3 Replies View Related

Bad Sectors On Hard Drive?

Jan 24, 2013

I am having a problem with my computer, it shows black screen after logging in, it won't display my desktop, even if i use another user's login details it seems as if it will display but then suddenly logout,but i can use the other partition without having a problem.

View 2 Replies View Related

Hard Drive Bad Sectors

Apr 17, 2009

I get my PC configured and set up exactly how I like it, and then my 1 year old hard drive conks out on me!

I did a CHKDSK and it had some bad sectors and plenty of file corruption. Ran the Hitachi DFT software and it seemed to think it has rescued it, but I'm using another drive now just in case.

Luckily I could still access my e-mails when I accessed the drive from another system, and everything else is backed up via Acronis.

View 9 Replies View Related

Windows 7 Finally Installed / Bad Sectors?

Jan 17, 2012

I've been having problems with installing a fresh OS because my harddrive. When I began the clean installation process my hard drive started clicking periodically (which didn't happen till I started) I was able to partition around these bad sectors and get the OS installed. I am now sitting at a clean desktop with the computer running fine.However, I know that these bad sectors will cause problems later and I'm wanting to know what I should do now. Is there anything I can do to kill these bad sectors and ensure my hard drive to stay proper? I realize that this shows my hard drive is going bad, but I feel if I can get this taken care of then I can keep the hard drive a while longer.

View 6 Replies View Related

Removing C Drive With Boot Sectors

Nov 5, 2009

Drive C was an old IDE drive with XP on it. I installed and new SATA drive for WIN 7. Win 7 installed and activated just fine. Now I want to remove the Old IDE XP drive from the machine but the boot partition is on the IDE drive. I need to know how to remove the old drive and make the new SATA drive bootable into the Win 7 install on it.

View 4 Replies View Related

How To Detect The Bad Sectors Of Hdd In A Laptop Before Booting

Jan 4, 2013

My laptop is not booting up. i tried reinstalling it, but still even with a boot able disk, the system is not loading up. I even tried reinstalling from the USB drive. still I the system isn't responding.

View 7 Replies View Related

Windows 7 Loading Operation Failed - HDD With Bad Sectors

Mar 1, 2012

I am having window xp running on that hdd but when I am trying to load windows 7 then setup recognize that my hdd having bad sectors and after running set it shows the fail operation of loading windows 7.

View 3 Replies View Related

Check If Bad Sectors Has Affected Windows Installation?

Jan 18, 2012

I have installed windows 7 x64, the installation went fine, it runs fine, no bsods, no crashes, no restarts, no freezes, no slowdown. Basically it just runs fine, all updates installed fine.

Now, I did a scan on the HDD, and it has bad sectors pending. I imaged the windows to another HDD.Loaded onto the other HDD, it boots fine, runs fine, idles fine, installed a few things, checked the files system, ran chkdsk ( just fix box, not the second box to repair ), all OK.So my question is, how can I know if the bad sectors on old HDD had any damage to the windows installation, and thus on the new HDD?

View 9 Replies View Related

Crystal Disk Caution On Reallocated Sectors?

Jun 8, 2011

HD passes Data Lifeguard extended CD test. How serious would you rate the Caution CDI is giving for Reallocated Sectors?

----------------------------------------------------------------------------
CrystalDiskInfo 3.10.0 (C) 2008-2010 hiyohiyo
Crystal Dew World : Crystal Dew World
----------------------------------------------------------------------------
OS : Windows 7 Ultimate Edition SP1 [6.1 Build 7601] (x86)
Date : 2011/06/08 20:08:03

[code].....

View 4 Replies View Related

Hard Drive Diagnostics Report Bad Sectors?

Jan 3, 2012

I am having serious corruption problems with my hard drive. I have reinstalled windows a few times now, but it always ends up being unable to boot. At the moment, my computer cannot even boot up in normal or safe mode, all my restore points have been deleted, and startup repair cannot do anything.After backing up my data and running a test with the Seagate SeaTools diagnostics in DOS, it was reported that there were bad sectors found on my Hard Disk. But I actually can't use this software to repair the bad sectors tough since it's a Western Digital drive. Is there any software that I could download to repair these bad sectors, or am I going to have to replace

View 5 Replies View Related

Read Files Not Through Win DLLs But Directly From Sectors/partition?

Nov 16, 2012

I assume I have a trojan which replaced a certain windows core DLL by a modified version.When I list all files in a directory (e.g. C:widnowssystem32) in Windows Explorer then certain files are not visible.Yes, I checked unhide hidden files on unprotect system files in WinExp options.So actually ALL files must be visible which is not the case.Is there a win-explorer-like tool which does not use this faked win

View 1 Replies View Related

How To Repair Current Pending Sectors On External Drive

Aug 1, 2012

One of my external drives (WD) appeared a warning in SMART status:

C5 Current Pending Sector Count
Current = 200
Worst = 200
Threshold = 0
Raw values = 1

If this is repairable problem, what is the best tool to repair this?

View 2 Replies View Related

Hard Drive Check Disk And Attempt Recovery Of Bad Sectors?

Nov 22, 2012

My external hard disk has been acting up i.e it would take time to load some documents. So I decided to perform the Check disk options. This has been going on for the last 3 days and am thinking of cancelling the process because it seems to be stuck and it is not even 20% done. What will be the consequences of cancelling it?

View 1 Replies View Related

Soft Recording Volume With Blue Yeti / Increasing Volume Distorts Audio

Mar 28, 2012

so i have a blue yeti, and i'm an online animator/voice actor. whenever i record audio on my blue yeti (or any other mic) i record about 4-6 inches from the mic, and turn the gain down enough that the audio doesn't peak as i yell or whatever. this is what you're supposed to do if you don't want your audio levels peaking and making your recording sound horrible and corrupted. however, afterwards, it means i have really quite recordings. not a problem right? now that it's recorded right, i can boost the volume of the entire clip afterwards right? wrong. i'm not an audio expert so i must be missing something. but why in gods name would the audio distort and peak after it's recorded successfully? it's all there, it's all clean audio. if i turn the volume on my speakers all the way up it sounds crystal clear! all i want to do is do that inside the computer so that when i upload it to Internet people don't have to turn their speakers so far up. but if i increase the clips volume in the computer, it distorts! it sounds awful! why?! i tried in sony acid and audacity and they both do the same thing! i can take sound effects, and recordings made by other producers and crank them up nice and loud, but mine just fall apart!

View 2 Replies View Related

Windows 7, Sound Limit, Audio Card Is Loud Windows Is Soft

Oct 24, 2012

I am working with Windows 7 on a Dell Optiplex 755, but teh issue is with the System Volume setting. When I go to the audio mixer and do the test and configuration, the SoundMax audio level is loud and clear. The problem is with the Windows system settings somewhere, is there a limiter or cap setting in teh registry that I can set to maximum? I know that it is not the standard slide bars/levels but somewhere that Windows 7 Professional is cutting the volume on any Windows application. The drivers are fine, if I invoke the card directly it will blast the sound out. But in any application it is too soft.

View 4 Replies View Related

Failure To Boot After Soft Boot

Oct 23, 2011

My computer hangs after a soft boot (reboot). Cold boots are fine.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved