0xc0000428 Can't Get Past Boot Manager
Dec 19, 2012
I have windows 7 on my laptop and I attempted to update my OS to windows 8, which was mounted to a blank DVD, in hopes of wiping everything due to continuous blue screens of death and automatic restarts. It looked like the installation was going to go through until the system restarted and the windows Boot Manager screen came up. It says the digital signature for this file couldn't be verified. When I boot up windows 7, system ecovery tools appear. Startup repair doesn't do any good. I can't restore because of no restore points. How can I revert back to get my laptop working again? I don't have a windows 7 boot disc
View 9 Replies
ADVERTISEMENT
Sep 7, 2012
Well first of all I started up my PC and it immediately jumped into Startup Repair maybe cause I didn't shut it down properly. It went through the repair and several times. By then I knew something was wrong, I checked the Diagnostics and see what Startup Repair had actually done. It turns out it could not fix an error with the OS Loader.It came up with two error code (0x2) and (0x490).I followed the following instructions:
1. bcdedit /export C:BCD_Backup
2. C:
3. cd Boot
4. attrib bcd -s -h -r
5. ren C:BootBCD BCD.old
6. bootrec /RebuildBCD
I also tried using /FixMBR and /FixBoot However none of these worked and my I tried booting up it came up with the same problem. I went back into the Windows 7 DVD and ran Startup Repair again. It said it was completed successfully but it said also if it doesn't boot then there's something wrong.Which leads to my new error screen that never goes away everytime I switch on the PC. The error message is as follows:A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source.If you have a Windows installation disc, insert the disc and restart your computer. Click "Repair You Computer," and then choose a recovery tool.Otherwise, to start Windows so you can investigate further, press the ENTER key to display the boot menu, press F8 for Advanced Boot Options, and select Last Known Good. If you understand why the digital signature cannot be verified and want to start Windows without this file, temporarily disable driver sginature enforcement.
File: WindowsSystem32Winload.exe
Status: 0xc0000428
Info: Windows cannot verify the digital signature for this file.
If I try and press ENTER it will take me to the boot menu and if I press ENTER to select an OS (I only have one) then it will jump back to the previous screen.
View 9 Replies
View Related
Apr 27, 2009
So I installed Windows 7 yesterday, my previous OS was Windows Vista 64bit, but along the way I have been running into some problems, and I hope someone can help.
Before I go on, I would like to add I have tried alot of different solutions, changing CMD, Bootrec, FIXMBR, I unplugged my secondary HD and so on, and nothing have helped so far.
My problem is that I cant boot from my HD, I have formatted twice, I deleted a small parition of 8gb which had some OEM files on, I guess from Vista at that point, and I formatted my C: drive before the install, both times.
Now I can boot directly from my Windows 7 CD, and it does it smooth.
The following error I get after a boot from HD is this.
Winload.exe
0xc0000428
Windows cannot verify the digital signature for this file
if I press enter on this screen, it takes me to the screen where you usually can press F8 for a menu, in this menu it only have "Windows Vista" and the Windows Diagnostic Tool if I press Tab.
If I press F8, it goes straight back to the Error.
I would like to add in the end, I did both try and run Vistabootpro 3.3 and easybcd, but to no avail.
I have added a small bcdedit copy I get in vista cmd http://img165.imageshack.us/img165/619/bootf.jpg
View 5 Replies
View Related
Jul 26, 2012
So a couple of days ago my computer started to act up but this morning when i turned it on, i got a blue screen and it never wanted to turn on ever since. So i tried reinstalling Windows 7 again on the current system because i do not want to lose my pictures. Is there any way to fix this?
View 2 Replies
View Related
May 1, 2012
I restarted my PC the other day (Dell XPS 8300) and then when it got the the Win7 login screen (the one where user profiles/pictures should be listed) a weird error message in wingdings font appeared. Eventually I learned to use a install/repair disc to use bcedit and bootrec from command line. Oddly, it seemed that my OS drive letter had changed from C: to E: . After a lot of research I removed a secondary hard disc I installed. The drive letter is now right, and the partition size seems right.y problem now is when windows starts I get an error saying that winload.exe cannot be verified. The error code is 0xc0000428. I've tried bootrec /fixmbr, /scanos, rebuildbcd/, /fixboot, with no luck. Same with start-up repair I understand that some people have been able to find a working winload replacement in /windows/system32 (sometimes called winload~1) but I don't seem to have luck.
View 5 Replies
View Related
Jan 20, 2012
From the 2 options given I chose "Start Windows Normally"....After pressing Enter it will not go beyond the black screen where it says "Starting Windows" and inmediately reboots to the "Windows Error Recovery" again.I then chose the other option which is "Launch Startup Repair", entered the Disk, wait for it to load system files but it reboots to the Disk loading the files again like an eternal loop.Tried the F8 Advance booting options, chose "boot in safe mode with command prompt", it starts loading but then it reboots itself again!!I don t know what is going on, this is very strange, yesterday I worked all day in the computer..My system specs are these:>XFX Nforce 750i SLI>Intel Core 2 Quad Q9400 @ 2666 MHz>3x2gb Corsair CM2X2048-6400C5 DIMM DDR2 PC2-6400U DDR2-800 (5-5-5-18 3-22-6-3)>ATI Radeon HD 4300/4500 Series>WD Caviar Blue 500gb
View 9 Replies
View Related
May 16, 2012
I can't get into the BIOS options to see what's wrong or to boot from a flash drive or CD, either. It just sits at the startup screen with the HP logo and says something to the effect of "Press the ESC key for startu options". Pressing ESC, however, does nothing (none of the F keys help either, I tried that).Anyway, here's how I messed things up. I was trying to install openSuse to my Windows 7 computer. First I went into my start menu and searched partitions, so I could change those. When I was first installing openSuse told me it was going to format all of my partitions, so I backed out to change those manually. I shrank my largest partition, which has the Windows operating system on it by the maximum it allowed (16,142 MB or something like that. It was a little under 16 gigs).
After doing that openSuse told me it was going to install to sda6, I believe, and when I checked the memory of the partitions it seemed to match up. When I went to install it after making the changes, it didn't say that it would format my partitions. I figured that this meant I was good and everything would install fine, and it definitely appeared to. I didn't change any settings or anything, but instead just installed everything as default from my flash drive using the 4.7 GB DVD download for a 32 bit PC (mine is a 64 bit, but I wasn't paying attention).
View 9 Replies
View Related
Aug 6, 2012
In the chaos of moving to a new house yesterday, a box my friend was moving ripped and a bottle of beer smashed onto my open and powered on laptop, scattering both liquid and glass everywhere. We immediately powered down and removed the battery, and placed the laptop upside down and mopped up the excess liquid from the outside as much as possible, and set it to dry upside down on a towel.My laptop is a Lenovo U330, I had my brother install Windows 7 on it for me last year, but he kept the disks so I don't have any of them.Several hours & some blowdrying later, we attempted to start up the laptop (I would have preferred to wait longer, but I needed to know if mine would work in case I needed to borrow my friend's for the week). The laptop will load the lenovo startup screen, and then flash the windows loadings screen (with the option to press f2 or f12) for a few seconds before recommending that I run startup repair. Which if I select it, will freeze after a few seconds. Usually my laptop's pretty noisy, but while the battery light flashes as if there is activity going on, there's no noise coming from it at all.
View 7 Replies
View Related
Nov 15, 2009
Ok, so iv put this computer together, installed windows 7 Ultimate 32bit and i got it up and running perfect for like a day.
The next morning i switched it on and was working good for couple of hours then it seemed like the whole computer started to slow down and i got a blue screen error. so i rebooted and tried to start windows but, it then says windows is loading files then goes to the logo loading and after that it just goes to a black screen!? iv tried everything to get it back running safe mode, low res mode, repair, boot from disk etc but nothing.
So i thought i would try and put the HD in another computer and wipe it to re-install windows but when i put it in another comp it does the same thing.. does the logo loading and then to black screen
Iv found that when i remove the HD from my PC and boot from the windows 7 disk then it gets to the windows 7 installation bit so do you think it could be a problem with the HD?
View 2 Replies
View Related
Aug 29, 2012
I just reformatted my computer everything running fine until I accidentally in installed a Microsoft thing I don't remember the name... After uninstalling it quickly went to blue screen of death and now when I try to boot the oc it goes to the loading windows then blue screen of death and restarts. I've tried putting a disk in to reformat but it won't load the disk, it just shows the blue background you get while installing windows.
View 1 Replies
View Related
Dec 29, 2011
WIndows 7 premium home version on a lenovo laptop freezing at splash screen. I can boot into safe mode just fine. Whereby I have to run a system restore back to an older date but the issue still comes back up and this seems to be especially true when trying to wake it from sleep mode.
View 2 Replies
View Related
May 4, 2012
I can't access system recovery or most of the advance boot options. I have tried using repair cds and install cds but the computer refuses to boot from cd drive my laptop is an hp model g61. I don't really know what other specs you need I have noticed it always stops when loading a certain driver atipcie.sys. The full error I get is: "Stop: c0000135 the program can't start because %hs is missing from your computer try reinstalling the program to fix the problem". I'm not even sure what that program is.
View 7 Replies
View Related
Sep 16, 2009
My problem is that windows 7 wont get past the loading screen when its loading the OS. I have noticed that it will work when i have only 2GB(one stick) in but when i try to put all 8GB(4 sticks) in, it wont work. This same thing happened when i was trying to install windows 7 from a fresh install.
View 9 Replies
View Related
Jan 18, 2013
my gateway 5260 stopped booting past the splash screen or loading screen in all instances...startup repair, loading windows normally and safe mode. It did this gradually first loading into safe mode and startup repair and now nothing boots up... i have changed my RAM... tried a recovery disk... tried himen's boot cd and trinity rescue kit 3.4...... tried windows defender scan.. no viruses... no RAM errors.
View 5 Replies
View Related
Jun 12, 2011
I have an ACER extensa 5630Z. It's been running all day, and I looked over and it had restarted and got stuck at a blank screen with a blink cursur, Every reboot will show the Acer splash screen, then straight to the blank screen with the blinking cursor. Any ideas what I can do to fix this? I've hit F2 and can get into the bios, but other than that I don't know what to do..
View 3 Replies
View Related
Feb 10, 2013
I've been scouring the internet trying to fix a boot issue with my Dell XPS 420. It worked fine last week but on Saturday started to blue screen. I installed a new HD and installed a fresh copy of Win7 64-bit. I reinstalled my ATI video drivers but nothing else (e.g. I had to update a load of codecs for Win7 on the other install). I tried booting again from the original hard drive and everything came back with no errors. I left the PC up overnight, and now I get the same blue screen with various errors. So I disconnected from that hard drive and tried to boot from the fresh install, now it blue screens there as well. So I hit F8 and tried to boot in Safemode with Networking. Hangs at the casspnp.sys file. Then tried to boot from the DVD and repair but the repair only gets so far and yet another blue screen.I have 8gb of RAM onboard, and I have an ATI 2400 video card installed that is jacked into a Panasonic plasma display. Other than that, I've not customized anything else. I've ruled out the RAM as I swapped it out. Could be the DVD as it was having what appeared to be I/O issues. However, it seems to work fine with I press F12 and boot from the DVD. I have this PC connected to a Port Authority KVM. I've reset the KVM as well. I also have a USB hub in the mix as well. I reseated my RAM, the DVD cables.
View 14 Replies
View Related
Oct 6, 2011
having problems with my PC rebooting since restarting to finish the installation of the latest Windows Update. Loads only to the Dell BIOS screen and then reboots again. I can hit F2 or F12, but not sure what to do when I do. I thought that running in Safe Mode and uninstalling the last update would be the way to go, but not sure how to get into Safe Mode.
View 4 Replies
View Related
Dec 29, 2012
smart failure predicted on hard disk 4 warning : imediately back-up your data and replace your hard disk drive. a failure may be imminent. press f1 to continue. what does this mean?
View 1 Replies
View Related
Dec 29, 2012
smart failure predicted on hard disk 4 warning : imediately back-up your data and replace your hard disk drive. a failure may be imminent.
View 1 Replies
View Related
Jul 18, 2010
I have been using my Windows 7 x64 system for about 5 months without a problem. I booted it yesterday, and an autoupdate occurred as soon as Windows 7 started up. It looked like this autoupdate made changes to /COMPONENTS. As soon as it finished, the system rebooted, and got stuck on the eVGA P55 splash screen. It was stuck there for about 10 minutes, so I manually shut down the computer. Every time I turn it on now, I get stuck on the eVGA P55 splash screen. I can not get into safe mode or anything. Any suggestions on how to go about fixing this? Did some stupid Windows autoupdate crash my new computer? I am turning those off if that is what happened.
View 9 Replies
View Related
Feb 23, 2012
Alright I am running Windows 7 ultimate x64 on my newly built computer. My computer can successfully boot past the bios and get to the logo screen. Then I get to the Windows logo which is a hit or miss. Sometimes it will boot successfully and I will have no problems whatsoever and I can enjoy my computer without worrying about anything. Then sometimes it will get hung on the logo and it will just stop responding. I don't know if this is an issue with my HDD or maybe my power supply. I think that this may be a problem with my power supply because I notice that my keyboard LED turns of when it hangs like that. The only question then is "why is this not a consistent problem that I can isolate?"
Here are my specs:
Case: Coolermaster HAF 922
CPU: Core i7 3930k (3.2 ghz stock; will OC to 4)
Motherboard: x79 Asrock Extreme 4 (x5 sata 6.0 Gb, x2 usb 3.0 ports, PCI-e 3.0 support, and quad-channel memory)
RAM: 8 gigs (2x4 gig's) of 1600 DDR3
GPU: x1 Radeon 6870
PSU: 600 Watts
HDD: 500 gig's 7200 RPM (Seagate baracuda)
Cooling: closed loop liquid cooling, Tuniq TX-2 High Performance Thermal Compound, and the standard fans on the case
Optical drive: LG 12x Blu-Ray reader and DVD combo drive
Monitor: 22" LED 1920x1080 -- ASUS VS228H-P (21.5 viewable)
View 8 Replies
View Related
Dec 25, 2012
this is what I did, since I have no CD-ROM, to install Windows 7 I created a partion X: NTFS and set it as the ACTIVE ONE, the put there the Windows 7 installation files, and opened prompt command to type bootsect.exe /n60 X: , next I restarted my computer, and automatically it booted into the Windows 7 setup, I installed Windows 7 on the partition C: and formatted the partition C:, everything installed and after the installation finished, a multiple choice menu appears that reads:[CODE]
View 6 Replies
View Related
Mar 11, 2009
How to Change the OS Name in Windows Boot Manager ?
View 0 Replies
View Related
Jan 13, 2013
ihave windows 8 my lpatop is acer aspire E1-531, I am trying to install windows 7 but boot manager wont show me dvd boot !! it show me only network boot what can i do to be able to boot from dvd
View 2 Replies
View Related
May 5, 2009
I'm having a problem every time I power on the system. I'm dual booting vista ultimate with win 7 build 7100; with vista I have no problem, but with 7 every time I start the system the first boot attempt gives me the error 0xc000000e after the boot manager display: "the boot selection failed because a required device is inaccessible".;after a reset the system boots 7 with no problems. Win 7 is installed in a brand new hd(seagate barracuda 1.5tb) and vista on a second hd.
I've search the web for people with a similar problem with no success. I've tryed already many solutions but the problem persists(latest bios for the motherboard, latest intel sata drivers, etc). I'm hoping that this could be a bug in win 7 instead of a hardware failure for the hd. Again, the strange thing is that this only happen after the power on. After that first error, no matter how many reboots, the system always boot without problems.
View 4 Replies
View Related
Nov 26, 2009
For some odd reason, after doing some changes to my partitions in Windows 7 and restarting my computer, I got the ol' "BOOTMGR is missing" message. I have the Windows 7 Repair Disc image file and a 4GB USB Flash Drive, but, sadly, no CDs. Is there any way that I can put the image file onto my USB Flash Drive and boot from it with my Acer Aspire X1200 desktop computer?
View 1 Replies
View Related
Jun 25, 2009
I had a dual boot system with XP Pro and Vista Ultimate 32bit everything was great.
I decided to try the Windows 7 RC but I needed a new drive due to lack of space.
My original drive is IDE, I bought a SATA drive and moved the OS's to the new drive.
I wanted to keep the old drive in system for storage so I formatted it and changed BIOS boot priority.
After fixing some minor issues with drive letter assignments due to the fact the bios reads the first and second IDE channels first then SATA.
I was all ready to install Windows 7 RC on an unallocated 100gb section of my new drive.
Note: that the old drive has a single partition formatted NTFS but is currently blank.
And I did follow the "Golden Rule" of installing the oldest OS first when I set up the computer in the first place.
The Install went fine.
Now for the problem.
Windows 7 did not add an entry into Vista's boot manager so no option to boot into Windows 7 without the install disk in the drive.
I used EasyBCD 1.7.2 from within Vista to add an entry for Windows 7. But when initially added easyBCD assigns the drive partition a drive letter that I don't have.
Therefore the entry does not show up on reboot. I changed the path to the correct drive and then the entry does show up on reboot.
But when I select Windows 7 the boot manager refuses to load Windows 7 saying that "cannot verify the digital signature of the file winload.exe"
I have tried wiping and re-installing the Windows 7 partition 3 times I've tried using the Windows 7 install disk to repair startup problems.
None of these has worked I'm at a loss as to what is happening.
If Windows 7 created a hidden partition for recovery and boot files I'm unable to find it, I thought of trying and Linux Live CD to look for the hidden partition but have not done it yet. My thought was to delete this hidden partition and wipe the Windows 7 partition and format it before re-installing either from within Vista or during the Windows 7 install process via a command prompt in an attempt to keep Windows 7 from creating this hidden partition. The problem is that I don't believe this will solve the problem due to the digital signature error reported by Vista's boot manager.
Can anybody help me with this or at least bring a perspective that I may be over-looking?
View 9 Replies
View Related
Jun 24, 2011
In attempting to install W7 64 on generic non-micro ATX [full] form factor desktop, Windows 7 will successfully begin installation. Upon reboot to complete installation I am informed that the boot manager cannot be found. How might I determine what is wrong so that I might correct the problem? Might it be a problem with jumper pins? No-o-o-o, it's not IDE HDDs I'm using; it's ATA. Might Microsoft's installation disc be at fault? I'll try using a different 64-bit disc with the [legal] new license, and then a 32-b it disc with the [legal] new license, but I'm at a loss. If it were the processor, it wouldn't even get to the install GUI that originates from the disc, would it? Otherwise, I'll have to take it to the shop and pay them to do a RAID 0(striped)config/install. The reason I'm posting this here is that I strongly suspect the 64-bit edition discs to be inherently flawed. On my 64-bit processor laptop, the 64-bit disc wouldn't install, but the 32-bit one did. I never worried about that because all I'm using on it are 32-bit apps. It's only on the custom-built desktop I need the 64-bit environment.
View 12 Replies
View Related
May 7, 2010
I tried to install WIN 7 to a NEW HD (clean install) since you cannot do a WIN XP upgrade install. I left my old C: drive (WIN XP) hooked up while I installed WIN 7 to the NEW drive. Afterward I decided that my computer is too slow to effectively run WIN 7 so I took the NEW drive out (WIN 7 installation) and intend to put it in a new faster computer.Now when I try to boot up my old C: drive with WIN XP, I get a WIN 7 Boot Manager. What a PAIN in the A--. How do I get rid of the Boot Manager so my WIN XP will boot up normally?
View 1 Replies
View Related
Nov 17, 2012
I have a windows 7 home premium 64 bit. And when i start the system i get the following message.Boot Manager:Windows failed to start. A recent hardware of software change might be the cause. To fix the problem:1.Insert your Windows installation disc and restart the computer.2.Choose your language settings, and then click "Next".3.Click "Repair your computer."If you do not have this disc, contact your system administrator or computer manufacturer for assistance.Info: an error occurred while attempting to read the boot configuration dataI searched the forums. But unfortunately i don have the installation disc.Is there any other way to get through this.
View 1 Replies
View Related
Apr 17, 2011
When receiving this message on boot up attempt running windows 7 home premium on a dell 1545 laptop with a fresh install and new hard drive would the problem be hardware related or software? Any chance it could be hardware related to the motherboard or is it most likely software related to the OS install?
View 1 Replies
View Related