My comp is acting weird so i decided to either repair windows or reinstall windows, but after it says press any key to boot from cd, and i press a key, i get a blank screen or it loads windows.
View 14 Replies
i recently attempted to format my computer as it was going very slowly, i did the usual process of inserting the recovery cd's which came with the computer however this time the process did not complete, i left it for over an hour and the screen still remained the same. I decided to restart the computer and a message keeps coming up, disk read error press ctrl alt delete. I tried formatting again but all i get is a blank screen even before its begun, i tried using windows xp cd's
View 7 Replies View RelatedTrying to start my computer and it gets to the screen where it gives me 2 seconds to press F11 to start recovery. But after 2 seconds or pressing F11 or any key, another line appears saying the same thing "Press F11 to start recovery". Can't get past this point and start Windows. HD is recognized in another computer as well as in BIOS.
View 5 Replies View RelatedWhen i turn on,first Windows screen appears,then a blue screen blinks,then hp screen,then a blank page with cursor on the top left,then a screen with the message"we apologise for the inconvinience but Windows did not start successfully.there was a hardware or software problem.I tried to run it in Safe mode, Windows normally,last known configuration but no luck......Then someone suggested to Get into the Recovery Console by making a Recovery CD with ISO image but the machine is not responding to any of it.Is it with CD/DVD ROM drive or any major hardware problem???...I ran a self hard drive test and it seemed fine
View 3 Replies View RelatedEncountered a Blue Screen of Death error. The error stated that I should run Chkdsk and then proceeds to restart and bring me to the Windows boot selection screen (safe mode, last known good configuration, normally). No matter which choice I pick, it always leads to the BSOD then restarts. Since this is getting me nowhere fast, I want to just format and reinstall windows. I do not have my recovery CDs, and when I enter the BIOS to change the boot sequence I cannot change it so the CD drive is above the hard drive in priority. The reason it gives me in the bios is that "All items on this menu cannot be modified in user mode. If any items require changes, please consult your system supervisor. Any ideas on how I can boot off the cd and reinstall windows from scratch?
View 10 Replies View RelatedPC running XP media edt. Once turned on I get The following file is missing or corrupt
windowssystem32configsystem.This happens even in safe mode. Then tried to do a repair with the system discs as soon a s I get to the recovery console ans type the Windows version to repair I get the dreaded blue screen with message Stop error 0x00000043 0XC35C6000 0X00000000 0X00000000. So I can't boot into windows nor do a repair. I@ve tested the memory.
My Help and Support stopped working about the same time I installed the free utility GhostScript / Gsview so that I could view postscript files. I tried posting a question on another usenet newsgroup, but the answer of: click on install on the C:windowsinfpchealth.inf file - resulted in a search for the file dataspec.xml in the C:windowsinfi386 directory - Unfortunately, such directory does not exist on my C: drive. Furthermore, the "K:I386" directory of my Original Win XP Home CD does not contain any file named "dataspec.xm_ or .xml".And beyond that, I ordered a new Win XP SP2 CD, which just now arrived by mail - and there is no "K:I386" directory on that CD, nor does the CD apparently contain any file called "dataspec" (including dataspec.*).Another effort toward resolution occurred via another usenet post I read, which suggested opening the XP command line feature and executing a system status command, that displayed enabled services - I used that method, and switched the Help and Support service off and then on again. Such action did not in-fact enable the Help feature (including, of course restart), despite the indication that the Help and Support service was enabled. I am, and have been, running a purchased-CD version of Win XP Home, with a downloaded SP2 revision (I have not installed the new Win XP SP2 CD). Basically, I want to find out the means and methods for enabling my Win XP SP2 Help and Support feature, that apparently has been disabled or otherwise rendered inoperative.Is a reinstall of Win XP possible and the best choice? What are the other options?
View 2 Replies View RelatedI have been having a boot up issue on my compaq presario sr1630nx. When I turn on the computer now it takes me to the boot screen where I press F2 and the little dash up in the corner flashes for a second or two...disapears...and then nothing...black screen. I then have to turn the computer off manually but when I turn the computer on again and it goes to the boot screen and I press F2 again and it takes me to the default start windows normally prompt.
I hit enter and then it boots up like normal and everything is fine with the world and my computer runs just fine until the next time I turn it off and have to turn it on again. Same routine at every boot. Was wondering if the brown out may have corrupted my boot.ini file somehow and if so how to fix it. My computer was on when the power spiked twice in a two minute period then was off for a couple of hours so it could be a hardware issue as well. I have Windows xp home edition
I am getting a blank screen with a white pointer when I boot up my machine. And when I try to boot up safe mode it does the same thing only with safe mode written in the four corners. Could someone please tell me what is going on.
View 3 Replies View RelatedI have windows xp prof running and now when i turn on the computer it boots up, goes to the logo, and then the screen goes blank. The hard drive is still working, and i can go into safemode (f8) but every time i try to startup normally the screen just goes blank, the monitor says there is no signal. I have no clue how to go about resolving this.
View 5 Replies View RelatedI have a computer I have built and upgraded several times for my step-son. The issue I am having is after startup or a reboot the computer goes through post and then I get a blank screen for 10-15 seconds. Then I get a serrated white load bar that runs the length of the screen at the bottom it takes about 3-5 minutes to load. Then I get the Windows load screen which takes about 10-15 seconds and then I get the account icons and everything is fine. I am not sure what this white load bar is from and it is really slowing down the boot times. The computer has gone through an upgrade and the issue still persists, which I expected. I upgraded the motherboard, processor, and video card.
View 2 Replies View RelatedI am using a custom built PC with retail bought Win XP SP2 installed.The PC is about 3 months old now and has run perfectly so far with 2 hard drives and 1 install of XP on the master drive (S-ATA). I redecorated the house and this resulted in the PC being unplugged for about 2 weeks. Havin just plugged it back in and tried to start it, I am getting through the POST stage and then I just get a blank screen with a flashing line at the top left. This used to happen with boot up but disappeared after about five seconds. This one just stays flshing forever.I was wondering if anyone would have any advice for me. If I haven't given any required details please ask and I will post them ASAP.
View 7 Replies View Relatedcomputer that won't boot up. I have an E-Machines T2825 running Windows XP Home Ed. that crashed after loading a wireless router and System Mechanic program on it. We bought another E-Machines computer (T6212) I networked the 2 with a Linksys Wireless - G Broadband Router. After that I loaded System Mechanic5 on both computers. After running a scan on the T2825, it told me that the hard drive needed to be de-fragged so I did it. Then, few days later, the T2825 started having problems when running programs on it. It would freeze up and the only way to shut it down was to disconnect the main power. After plugging it back in and turning the power on, it froze up just trying to open IE6.
View 14 Replies View RelatedWhen I turn on my lap top, Acer Travelmate 2355LC, there are a couple of quiet clicks, then nothing. If left for about 10 minutes, it starts up normaly. Sometimes it starts normally from the beginning.It has an Intel Celron M360 processor (1.4 GHz, 400 MHz FSB, 1MB L2 cache) 40 BG HDD 256MB DDR, I've cleaned everything up. Should I try and repair? I would like to avoid reformatting if possible.
View 2 Replies View RelatedA friend of mine called me to his house to take a look at his gateway. All I know is that it runs Windows XP.He states that AVG antivirus prompted him to restart his computer once the virus definitions update completed. Once he restarted, a blank screen appeared and said, "Invalid Boot Disk, please insert in drive a:"Problem is, there is no disks in any drive.
View 8 Replies View RelatedWhen I turn my computer on it goes to the blue hp logo and then to a blank screen with a blinking cursor in the top left corner. If I hit f8 when booting it gives me 2 options...f1 to setup and f2 to resume. It won't let me go into safe mode or anything. I have tried booting from the xp cd, but nothing happens. I have tried replacing the battery and that hasn't done anything. It started when trying to open a program, the computer just went blank. When trying to reboot, this mess started.Also, I just got this error message, which is new.i got it after I unplugged the computer for awhile.. warning 251: system cmos checksum bad dafalut config used
View 11 Replies View RelatedJust wanted to give a solution for an issue that I had on a Dell Optiplex GX270, where it was having problems hanging when a couple of peripheral USB items were plugged in. After I had installed an HP printer, I plugged in an 8Gb thumb drive. It would hang for a very long time until I finally had to reboot. When it went through the short Dell setup screen, it just went black with a flashing underline in the top left corner instead of going to the first Windows startup screen. The funny thing is that I would unplug the HP printer's USB cable while the computer was still powered, and it would immediately start Windows. Through several different test cycles I found that A) Leaving the printer USB cable plugged in during a restart brought up the blank screen w/flashing underscore. B) Not connecting the printer USB cable during a restart brought Windows up properly. That told me that there was a problem with BIOS. I went to the Dell website and flashed my BIOS with the latest update for my computer. That resolved the issue immediately.Hope this helps others resolve similar problems, because it seemed like there
View 1 Replies View RelatedThis is my first post on this site, I know that there have been posts on this topic becfore, however mine is different than the rest of the posts. In the other posts,this has occured on a modified computer, but when it happened to me, it was my unmodded computer. So heres what happened. I boot up, and after the HP screen, instead of going to the windows loading screen, I get a message with alot of text, but the main point was that "a failure was imenent", F1 to continue, F2 to enter setup. So i hit F1 to continue, and after a minute of a blank screen and the blinking text dash, the DISK BOOT FAIlURE, INSERT SYSTEM DISK message. But I have never modified my coputer, and never used a setup disk before on this machine. BTW:I tried resetting BIOS, but to no avail.
View 6 Replies View RelatedDell inspiron 510 laptop starts with dell logo XP logo and moving bar below then grey blank screen instead of users names only blank screen with moveable cursir used yesterday as normal except i did defrag
View 3 Replies View RelatedDell Dimension 4300 crashed on me. (I got the "Strike F1 key to continue, F2 to run the setup utility" message).I changed the order to the disk drive under the setup utility and was able to get it to recognize the Windows XP Install CD but that's where I'm unsure what to do. It gives me the option to either set up Windows or repair using Recovery Console.If I reinstall will I lose all the files on my computer? I have photos of my first born on there that I don't want to lose!
View 17 Replies View RelatedXP Home, SP2.My XP screensaver motion has become bad. It moves in a jerky, sputtering way and has been doing so for months. Also it will only operate at one speed - slow - regardless of what speed it's set. Is there a way to repair the screensaver program, can I uninstall/reinstall? If so, how? If an XP disc is needed, what I have is the reinstall disc from Dell, which I have never used.(I'm talking about XP's own system screensaver display - I didn't download anything.)
View 6 Replies View Relatedfirst i get the HP blue screen. I tried F1, but i dont see my hard drive in the boot menu. I followed some steps in Hp's web site- took the cpu apart and unplugged both hard drives from the motherboard, plugged them back in. when i restarted ,i got the HP screen and then windows started to load up. After a few seconds the HP screen came back up and then the black screen: sk boot failure, insert system disk and press enter. I also noticed that pressing F10 for system recovery does nothing.
View 3 Replies View RelatedI recently overwrit a version of windows. It did not save settings and files for programs that are integral with windows. When I want to use Yahoo or other programs that require integration from windows I get warning messages. I want to just start from scratch. (all programs and apps are on the hard drive and accessable from explorer) is there a function that allows me to format and remove all info except windows? Otherwise I have to reinstall/repair all programs
View 7 Replies View RelatedWhen I turn on my computer, I get the following message:
"We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.
If your computer stopped responding, restarted unexpectedly, or was automatically shut down to protect your files and folders, choose Last Known Good Configuration to revert to the most recent settings that worked.
If a previous startup attempt was interrupted due to a power failure or because the Power or Reset button was pressed, or if you aren't sure what caused the problem, choose Start Windows Normally.
When I turn on my computer, I get the following message:
"We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.
If your computer stopped responding, restarted unexpectedly, or was automatically shut down to protect your files and folders, choose Last Known Good Configuration to revert to the most recent settings that worked.
If a previous startup attempt was interrupted due to a power failure or because the Power or Reset button was pressed, or if you aren't sure what caused the problem, choose Start Windows Normally.
I got a problem
I use a developer program to make executables (hobby of mine saves me going troppo) called Clarion, it works OK, I made a DOSable program with it, it works OK.
Once I could open to full size DOS screen by pressing the Alt+Enter keys and it would stay open until I was finished with it, then I could revert back to a small screen by pressing Alt+Enter keys again.
Now if I press Alt+Enter keys the DOS screen appears, but it stays open in full screen for a couple of seconds then automatically closes back to the usual small screen.
I have tried right clicking on the icon, properties, screen and putting a dot in the full size option, but this does not work.
I have scanned my PC for viruses etc but no joy there.
I have Dialup only, so don't ask me to do a Panda or Trend scan as they drop you if you no got broadband.
I'm using XP pro, 512meg ram, using a Gigabyte MB, and Nivida video card.
XP working OK-dokie, sound ok-dokie, video ok-dokie, screen to DOS wonkie.
how to fix this?
I have searched for some weeks now and have seen an increase in people who also found that while viewing in the Full Screen option on You Tube and/or Hulu.com that the "Press Esc to Exit Full Screen" message that appears in the center of the screen does Not fade away after a few seconds. Of course that makes Full Screen viewing unacceptable. I posed the question to the site itself and have never received a reply. One general forum said something about Unlocking certain Files (Adobe) that were found locked because of cookie handling upon installation, but as a novice that is beyond my comprehension.In any case, is anyone aware of a fix for this problem? (That message is not suppose to stay there) I am using Win XP IE8. I tried viewing using the Firefox Browser (3.5.2) and it did not help.
View 3 Replies View RelatedI have been trying to install Windows XP as a second OS as I already have Windows 7 Ultimate installed. Unfortunately, after I select a partition, format it, and reboot the system stalls on the screen after the BIOS that has something to do with a list of devices and such. After 10 or so seconds a few characters and letters go blank randomly on the page. I rebooted and selected my cd drive as the boot device and accidentally didn't press a button in time to boot and a bunch of highlighted numbers were thrown all over the screen and a random smiley face on one of the lines.
View 12 Replies View RelatedFormat the partition you are going to use for the install.Restart your computer.Go into the BIOS Change your boot order and Make the CD-ROM your boot drive.Insert the CD and restart the Personal Computer.When prompted, Press Any key to boot from CD-ROM.Make sure that your computer is boot able by CD, otherwise this will not work.
View 9 Replies View RelatedToday my computer went slow so i restarted it and from that point it kept doing the same thing: it starts, then the dialog where it asks u if to start normal or safe mode (but keyboard doesnt work) then after the 28sec it tries to load windows, but a blue screen is shown and then restart again. I put the reinstalation CD but when i get to the "To boot from CD press any key" i cant becouse keyboard is not working.
View 7 Replies View RelatedAnyone know how to automatically boot from the hard drive? Has any one seen this before? I have been in the BIOS, set the hdd as the first device to boot from.I have looked through the BIOS but I can't find anything that jumps out as different or pertaining to this Boot Message.I looked at the boot.ini file, nothing there.I am running Win2k Pro.I don't know where else to look to disable this boot interaction..
View 7 Replies View Related
