I installed a program called Edison by Verdeim. I removed it but now if I turn the computer off when rebooting says to hit F1 to continue or hit enter(I think) to enter setup. Want out of that and just have regular boot. How do I get to bios
View 1 RepliesIve just installed a new motherboard and cpu but are now having issues getting going. The cpu is a AMD 3700 939 single core.The MOBO is a Gigabyte GA-K8NSC-939.
I have 1 gig of ram running on single channel and have tried swapping them out and moving them around with no success.I have a X850XT graphics card installed.
If i try and boot with the existing os on the harddrive it just keeps going through the boot cycle over and over.If i try and run the XP setup it locks up where it says Setup is Starting windows at the bottom left of the screen.
If i run Knoppix from cd all is good and i can get going and explore my harddrive etc.
I finally got sp2 installed and most things seem to be working ok. I had a problem with Nikon Capture software but got that resolved with Nikon tech last night. Now the only thing left that is bugging me is after boot up it goes to a black screen and hangs for about a minute, then goes to a black screen with a black and white progress bar across the bottom of screen and it takes about 2 minutes before it goes to the windows startup screen and boots up normally from there. I have been to Microsoft support site and looked thru the archives for this particular problem and can't find anything.
View 7 Replies View RelatedI've just had to install my machine after a major malfunction. It's running fine now, but everytime I install a new program, when I restart the machine, all the newly installed programs' folders pop up (e.g. showing the uninstall and help links in the program's particular folder; it usually happens with new software just the once) - and it's getting ridiculous. I have to close each folder one by one.
View 8 Replies View Relatedthe Windows Installer screen opens telling me it is trying to install a program that is already installed,(usually driver for HP 4110 printer drivers). If I don't cancel it immediately, eventually an error screen appears telling me the file I'm seeking is not available and to insert the installation CD. I've tried re-installing the drivers by inserting the CD, but then an error message appears saying the drivers are already installed. This is getting frustrating?
View 4 Replies View RelatedLast night I connected a friend's HDD to my PC so he could back-up some files onto my PC before he formatted his.He did that,and then insisted that he needed to format it ASAP,so he did so using my cables.So I turn my PC on later I find that most of the contents of my desktop are missing,and that several Apps are as well.I look in C:Documents and Settings and notice a new profile called "TEMP" alongside my normal profile with many of My Documents and personal settings for apps. For some reason, my PC loads up this TEMP profile only now, as opposed to my normal one.
View 10 Replies View RelatedI installed Norton 2009 and I have noticed my computer was different. Now I cannot even get passed the startup screen.It is like its frozen,the on/off button at the front doesn't work,only the restart. When I click on my user account to log in, nothing at all happens.I am on my husbands laptop right now. It is an old computer,but can it just die like that?
View 4 Replies View RelatedI want a program to run at startup and I want to be able to change what I have done at any time.
There are a number of unchecked entries in msconfig and I have to use Selective Startup all the time.
If I want to revert to Normal Startup under the General tab instead of Selective Startup, the program's box automatically rechecks itself in Startup.
The Startup tab gives me a handy record of what I did and allows for an easy change of mind so long as I continue to use Selective Startup.
If I edit the Registry to stop programs running at startup, they won't show in msconfig and I lose the handy record of how it was and I may have to reinstall the program to go back to it running at startup.
I would like to accomplish this:
1. Use Normal Startup instead of Selective Startup.
2. Have some programs not run at startup, but be able to easily change back to having them run at startup.
3. Have a readily accessible list of those programs and the details as shown under the Startup tab as a reminder of how it was without having to manually enter it all into a text file or keep a notebook or reinstall.
Is there some way to use Normal Startup, stop programs running at startup, but retain or find a list of those programs (including the details under the headings Startup Item, Command, Location) that is shown when using Selective Startup with unchecked boxes under the Startup tab?
To put it another way, use Normal Startup but somehow retain the convenient flexibility of Selective Startup.
My startup time went up drastically.
I have disabled all but two of the automatic startup items using msconfig. My system used to start in less than two minutes, easily. Now it takes a more than a minute or two longer than that.
I know what the problem is; the only three items that show in the system tray after startup are:
1) The AVG Antivirus icon .
2) The Spybot SD Resident icon.
3) Local Area Connection (This is the icon which shows two computer monitors with screens that light up and go dark periodically)
Now, after the problem started, the last item, the Local Area Connection icon is the one that doesn't load, for VERY long. So it may be something to do with that. Also, just before the icon finally shows up(after which point the computer is fine to use) I've notice that a Windows security notification icon appears...it flashes, for just a second, and then is replaced by the Local Area Connection icon. For the record, these are the two icons I'm talking about:
http://i131.photobucket.com/albums/p282/sw1sh1/LAC.jpg
http://i131.photobucket.com/albums/p...tification.jpg
I have had my automatic updates disabled for a while now, so you might think that that's the reason the notification is showing up but I've already disabled that notification using Windows Security Center.
Try making my laptop less slow and not freeze all the time when doing the simplest of tasks.
However, my problem happens after trying to disable the Startup Items from the MSconfig dialogue.
-After I have unchecked the boxes I don't want, I click OK or Apply;
-It then tells me I have to restart for the changes to take place, so I do this;
-Then after completing its restart a message says that "The System Configuration Utility is in Diagnostic or Selective Startup mode, causing this message to be displayed and the utility to run every time Windows starts up."
-it then opens the MSconfig dialogue box again.
If I just close the utility or click ok, sure enough it keeps on opening every time I startup. Or else, what it's trying to convince me to do is to start up in Normal Mode. But I won't do this because then all the Startup Items I'd disabled become enabled again and the whole lengthy task was a waist of time!
The run link is missing from my startup menu...can anyone help me find it? I know this sounds dumb, but I really need to restore it to my startup so I
can take care of some other problems I'm having.
How do you remove the "Common Startup" items from the startup list in msconfig for Windows XP? I did locate and remove the "Run" items that are located in HKLMSoftwareMicrosoftWindowsCurrent VersionRun.
View 6 Replies View RelatedWin XP Home edition. I'm in the Speed Up Windows Startup class. I currently have a very long list of startup programs running. Is it safe for me to disable all except security programs (Symantec Norton,AdAware,Spyguard)?Charles
View 6 Replies View RelatedI think I might need to do this.It's now impossible to click or d/click on a programme or even an email and have it open I have to click 6-10 times before the little hourglass appears.I think I need to change my startup : what do you think? Msconfig shows my startup options to be -Normal Diagnostic Selective
Ought to to choose diag?Or Selective?because I can't decide which programmes I ought to remove and which to leave in, but I'm sure I have too many.
I've installed the new drive, formatted it two partitions, and installed my XP on the new drive. The old drive is still installed, and I can select which drive I am booting off of. Boot off the old drive, I'm on my old PC. Boot off the new one, I'm on the new.Only one of the XPs are active at a time. The other says it must be activated.
So, at this point, I boot to the old, and (with this OS activated)run the Files and Settings Transfer Wizard. I specify that I am saving the data on one of the drives in the PC. It runs and says it's successful. Then I boot off the new drive and (now with THIS OS activated) when I point the FAST to the directory where I saved the files, the wizard says there's no files there to load. I can see .dat files in the directory, but the wizard can't.
My sister's computer is running very slowly, particularly at startup (which seems to take forever). I've got Panda antivirus software running and do reasonably regular spyware scans with AdAware, but am not sure if the problem is just that the computer is old with too little memory / overheating because it's on almost all the time / something else I haven't thought of. To help me determine what's going on, could someone much smarter than myself take a look at this HJT log and see if you see anything of concern?
View 14 Replies View RelatedThe problem is it takes an incredibly long time to startup because of these, once we close them it gets back to running fast, but until then we have to wait for them to open. I think it's causing the problem because we didn't have this problem until we installed this.How do I make it stop starting up on Windows XP? I sped up my startup on my computer by stopping useless things from running.
View 4 Replies View RelatedIve installed xp pro and formatted my hard drive after i had a nasty virus which basicly stopped my computer from booting. However for some reason it seems like ex pro hasnt picked up any of my drivers at all, like i have no sound no internet. Im not really sure what to do im sure my first step would be getting onto the internet but my ethernet is plugged in nothing shows on my connections and i am unable to create a new conection, sorry if i havnt explained myself very well my computer skills arnt great.
View 14 Replies View RelatedI am about to install service pack 3. I have not heard any good or bad new about it.
View 8 Replies View RelatedIcrediMail XE, it's half way installed and stuck there, hasn't moved in the last hour, so I cannot uninstall it at Ad or Remove.
How I got it in the first place I do not remember,
Is it possible to install W2K Pro over an existing XP Pro?
View 4 Replies View RelatedI've had some problems with IE crashing. I have Windows xp with sp2 installed. I went through the error report and most contain a problem with mshtml.dll. I got the windows web site and it said that there is some problem with sp2 in this case and they have a hot fix. But it looks like I would have to pay $99 bucks to contact microsoft and get it.
View 1 Replies View RelatedI have a hp pavilion a335w home pc, O/S Windows xp home with serv pack 1. This was pre installed when purchased. Problem: in the middle of using mcafee removal tool my system crashed when it rebooted I got this messege: windows could not start because the following file missing or corrupt: windowssystem32configsystem. My question is this, what is the best way to hopefully replace the missing file so I dont loose everything.
View 14 Replies View RelatedEvery time I reboot I get a message box stating this file is missing. What is this and how do I repair the problem.
View 5 Replies View RelatedSince installing Service Pack 2 on my system (Athlon XP 2400+, Windows XP Pro, 512Mb) I am having intermittent problems with my machine slowing to a crawl. If I use task manager I find that CPU usage is 100% and quitting programs seems to have no effect. CPU usage stays at 100%! Can't remember this happening before installing SP2
View 4 Replies View RelatedRecently I became devoted to taking care of my computer by installing Anti-virus, spyware removers, and backup/performance utilties. Well I came across BartPE and it's features. Well I decided to use it and have the Rescue CD just incase. Doesn't hurt right? Plus the idea of it seems very helpful if I ever need a virtual Windows XP. I continued with the instructions and all was well until I got errors and warnings.
I posted the log here. I have no clue on what to do next. I used the CD that came with my Dell Dimension E521. I use Windows XP Media Center 2005.
Since I have had my comp (going on 4 months), when I boot i get a message saying BIOS is not installed, which i find very hard to believe, but this never affects anything. today when i boot my comp, it starts loading and its:scaning IDE drives then it says something about BIOS not being installed (but it was a slightly different message, i didnt have enough time to record it). then i get some weird screen, it gave me the option of entering setup by pressing F1 or loading default settings by pressing F2. i rebooted, again the same message, so i just chose to load default settings, and everything loaded, but when i got to loading windows, i loaded it and then it crashed, the comp just rebooted. then i followed the steps again and loaded default settings and it loaded fine. i know i cant give details about the error screens as i didnt have time to record them, but what should i do if this happens again?
View 14 Replies View Relatedwindows messenger will not un-install no matter what i do help
View 3 Replies View RelatedI recently had a corrupt file and ended up doing a full repair of XP-home. That wiped out IE7-- replacing it with IE-6. I had some trouble downloading updates so replaced IE-7---- Now almost everything works fine. The exception is that I get notified that "Updates Are ready for your computer-- Click here to install these updates". I click on it and it looks like the updates are being installed-- just to be notified that "These updates were not able to be installed" (Words close to that). A few seconds later I am informed that "Updates are Ready for your computer" And the cycle continues. I have tried "Custom" (my normal way of doing them) and "Express" (in frustration)--- all to no avail.
View 4 Replies View RelatedSo basically, I tried repairing a Windows XP Media center install by booting from a Windows XP Pro CD and then using the Repair function.I didn't use Media version, because the only install CD I had on me was Pro. It was probably a bad idea to install Pro over Media.
1.) Boot the computer using the XP CD. You may need to change the boot order in the system BIOS so the CD boots before the hard drive. Check your system documentation for steps to access the BIOS and change the boot order.
2.) When you see the "Welcome To Setup" screen, you will see the options below. This portion of the Setup program prepares Microsoft Windows XP to run on your computer
I installed Win XP Home on a computer that already had it installed. I really wanted to do a reformat and then install Win XP Home. So, now when I boot up, I get a choice of either of the installations. I want to delete one of them; how can I do this? Once this is done, and when I have more time, I would like to do a clean install. How do I do that?
View 2 Replies View Related