Install On SATA Drives - BSOD - STOP 0x0000007b
Aug 3, 2010
I have a Acer Aspire AM5640-E5520A Intel Pentium 2 QUAD, 2.4GHz with a MCP73PV motherboard and SATA drive. When I try to install XP (which I like better than Vista) the set up acts ok ,loading files, until it gets to "setup is starting windows".. Then I get the BSOD and a message saying STOP:0x0000007b. I have tried to change the bios setting for the HD to IDE but I do not find anything about storage or AHCI. All i see is a place to change raid configuration. Raid is disabled. But i have tried it with raid being enabled.
View 3 Replies
ADVERTISEMENT
Aug 25, 2010
All new system Asus MB core i7 4 gig ram with sata drive. All hardware is up in the bios and recognized. I get the Stop:0X0000007B on install of XP pro service pack 2.
View 2 Replies
View Related
Feb 27, 2010
I want to install Windows XP on a new SATA HDD drive. The computer in question came with Windows Vista installed. There is no IDE option in the BIOS. There is no floppy drive on the unit. So it looks like I might have to slipstream all the drivers, etc., on to the unit (which I have no clue how to do). I do not have the motherboard make or model number, nor do I have the motherboard CD. My business partner is trying to take the cover off the laptop as we speak, but we're having trouble getting it off. Thus, as of now, we can't identify the motherboard manufacturer or the serial number.
Can anyone here point us in the right direction? The computer in question is a Compaq Presario c769us (laptop). It was purchased in June 2008. This all started when my business partner decided to use a Vista System Recovery CD to overwrite the existing copy of Vista that he had on the computer. After he ran the disk, the system stopped working. So right now, we have the old hard drive, which contains a non-working copy of Vista on it (which we can 't delete), and we have the new hard drive (a 250 GB Hitachi). So maybe we could just delete the copy of Vista on the old hard drive - the self drive test checked out okay on the old hard drive. So I guess the two options are - figure out a way to put XP on the NEW hard drive, or figure out a way to put XP on the OLD hard drive and delete Vista from it first. If we can put XP on the old hard drive and remove Vista from it, we could take the new hard drive back, and get our money back, too.
View 14 Replies
View Related
Aug 19, 2009
This is similar to the problem B1177 posted about, but I'm having no luck solving it myself. Basically, I have an IDE CDROM into the mobo, and a SATA HDD hooked to a Koutech Initio-chipset SATA controller card. In the card's setup at boot, it says the drive is "passthrough". I confess I'm not sure what that means. I'm new to SATA. I slipstreamed the Inic1620 drivers into a new CD with nLite, which stopped the "Setup cannot find any hard drives..." error, and allowed Setup to continue. After loading files, however, on restart I get the ever popular STOP 7B BSOD. Windows DOES begin to start, and the splash screen shows for a second or so, then it's into the ol' freezerino. Email to Koutech support has gone unanswered.
The machine is a Gigabyte 6IEML/P3900/500MB with an Intel 82815/801B chipset. I also tried restoring an image from another machine with an Intel chipset--though not the same one--and it stops at mup.sys, but that may have nothing to do with the SATA card. Interestingly, although Windows Setup couldn't find the drive, a Hiren's CD, with no SATA drivers loaded, could. Actually, a bit more than interesting isn't it?
View 2 Replies
View Related
Nov 18, 2004
Major virus infection on computer resulted in fdisk and reformat. I used Win 98SE to fdisk and reformat, as I couldn't for the life of me find a format on the Dell Operating reinstallation CD. (could be first mistake)
Used Win 98 SE startup diskette to start system w/CD rom support.
Navigated to D: Drive which containe the XP OS reinstallation. Navigated to I386 folder and typed WINNT to begin reinstalling files.
Start WIn XP setup and began copying files to HD.
Screen shows: The MS-DOS based portion of setup is complete. Setup will now restart you computer. After your computer restarts, WIN XP Setup will continue. Remove floppy, etc.
Computer restarts - did inspection of system, shows Win XP Setup, loading files (drivers, controllers, etc.)
Starting windows - Welcom to Setup:
1. Setup - press enter
2. Repair (using Repair Console)
3. Quite - F3
Pressed enter
Next message:
Setup did not find any hard disk drives installed in your computer. Make sure any hard disk drives are powered on and properly connected to your computer. This may involve running a mfg supplied diagnostics or setup program.
Setup cannot continue Press F3
System then attempts reboot, attempts installation again by booting from HD. Then error message:
Stop error:
Stop: 0x0000007b
(0xf7cb063c, 0xc0000034, 0x00000000, 0x00000000)
At this point I must shut off the PC.
System:
Dell Deminsion 4600 series p4 processor @2.4 GHz
512 MD DDR SDRAM @ 400 MHz
128 MB DDR NVidia GeForce FX 5200 graphics card
80GB 7200 RMP Ultra ATA HD
Win XP Pro SP1
48x/24x/48x CD-RW Drive
SoundBlaster Live! w/ 5.1 support
I have looked on MS site for the error code and think I understand that the problem is either a hd controller device driver is not installing from the Dell Reinstallation CD and therefore stops the installation of the software. How I can possibly extract and install the driver setup may be looking for.
View 13 Replies
View Related
Jan 14, 2009
Continually getting STOP: 0x0000007B when installing XP on an Acer Aspire E700. Drive had Vista installed. Have deleted all partitions - drive is empty.
I believe it's related to the SATA drive, but haven't figured a way around it, and time is money.
View 6 Replies
View Related
Sep 1, 2005
Whenever I attempt to reinstall Windows I receive a stop error warning about a possible virus to instructing me to remove any newly installed hard drives
and/ or controllers. I elliminated hard drives disk by disk but was met with the same results. I then elliminated all HDs and my SCSI controller, booting from my XP CDROM.
View 2 Replies
View Related
Aug 28, 2005
I recently upgraded to multiprocessor and new motherboard, now I am getting this stop error message and my hard drive will not enter into windows.
View 9 Replies
View Related
Apr 4, 2006
After powering down during a system restore, my Dell Inspiron 1100 Laptop is caught in the loop that results in the above Blue Screen error. None of the modes work, last known, safe etc.I have read a lot of the posts about restoring that system and am not so concerned about getting the laptop up and running but just recovering the data from that drive - pictures from the laptop.Is this strategy below an option? 1. Purchasing a USD Hard Drive Enclosure. 2. Removing the hard drive from the laptop 3. Connecting the laptop d it to the Enclosure 4. Plugging it into our pc to copy the files. Since the drive will not boot via the laptop, am I right in saying that the drive should be readable as any other drive if connected in the manner above.
View 7 Replies
View Related
Oct 17, 2009
Recently I bought a very cheap Acer Aspire M1640-E1150 which came with an MSI motherboard, an Intel Pentium Dual Core E2200, 2 GB of DDR2 RAM, and a 320 GB HDD from Hitachi. The system came with Vista initially installed on it, and needless to say, it was very slow! I decided to do the right thing and go to XP, so I found all the drivers required and I proceeded to install Pro from a disc that I have from a previous computer. As soon as the screen booted up and the system was being checked by the program, the system gave me an error message, before I even got to partition anything, it was initial. I tried to restart, took one of my RAM sticks out, but nothing was working. I even tried to format the HDD through an external drive, but nothing was working.
The error message is "Stop: 0X0000007B" and something about a virus or a software or a hardware being the problem. The system was running smoothly on Vista, and I even formatted the C drive, and I am sure that there were no viruses.
View 6 Replies
View Related
Sep 24, 2008
i got a window 2000, that has been used for simple stuff like web browsin, aim ect. and one night it had a hard time shutin down, so i just pressed and help power button, i did same thing next night. well tonight i got the famous STOP: 0x0000007b error (0x8180dc50, 0xc0000032, ect...) error and i was wondering how can i fix this? i found on the other site that 0xc0000032 means that i need to run chkdsk /f, but thats not possible since it wont start
View 6 Replies
View Related
Apr 19, 2010
I have 4 or 5 year old Win XP Home Tiny desktop computer which is having trouble booting. Basically when booting up, right before the Win XP logo it reboots itself.I have disconnected all IDE devices except for the master hard drive (plus disabled them in BIOS), I have tried a different hard drive in the machine that I know is working and has XP Pro installed. The same thing happens with this hard drive - reboots. This hard drive also has Ubuntu installed, and the machine happily boots Ubuntu to the normak desktop, but for some reason won't boot XP!Also tried a third hard drive in this machine that is working with Win 2000 installed, again the same thing happens.
Next I tried the original hard drive in a working seperate machine which produces the same result again.Also tried removing the RAM from the original machine and inserting a stick of working RAM from my other machine which again makes no difference.All hard drives I've tried have the correct jumper setting (primary master).
Also tried putting the Win XP disc in the drive and booting to that, I get to the menu and try to do a repair (R), but a few seconds after the repair begins the system reboots (this is using the original hard drive).Also tried booting into safe mode, and last known good config on all drivers.The hard drive is being detected in POST and in the BIOS which I have set as the first (and only) boot device.When I turn off the auto reboot upon fatal error, I can see the blue screen of death with error code 'Stop 0x0000007B'.So looks like the hard drive might be knackered, but there must be something else aswell because my two other working hard drives don't boot XP (only ubuntu)
View 13 Replies
View Related
Jul 18, 2008
I put in My CD and it goes through the first blue screen (the one where is asks if you want to press f2 to do install drivers via A drive etc) and when it gets to "Setup is Starting up windows" (this is before all the HD formating and partitioning) I get the blue screen. it does not have much info on it all it says is:Stop: 0x0000007B (0XF78D2524, 0XC0000034, 0X00000000, 0X00000000)
View 5 Replies
View Related
Nov 6, 2009
I want to downgrade the factory loaded Vista to XP pro on my Acer Aspire M5640 desktop. I found some detailed instructions on line for doing this, but I don't get very far before I get a blue screen error message while the computer is in the process of booting up from the XP disk and loading the files while in windows set-up mode. It reads as follows: "A problem has been detected and windows has been shut down to prevent damage to your computer.
"If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: "Check for viruses on your computer. Remove any newly installed hard drives or hard drive controllers. Check your hard drive to make sure it is properly configured and terminated. Run CHKDSK /F to check for hard drive corruption, and then restart your computer. Technical information: STOP: 0x0000007B (0xF78D6524, 0xC0000034, 0x00000000, 0x00000000)
View 1 Replies
View Related
Sep 4, 2007
I am trying to install windows XP Pro on a Dell Dimension 9200 with SATA drives. I have tried the F6 but I don't have a floppy drive, is there a way to use a USB thumb drive, to provide the SATA driver?
View 3 Replies
View Related
Feb 25, 2006
It's looking like I have to re-install C+XP Pro SP2. I have never installed XP Pro SP2 before myself on SATA drives - I know that you used to have to get the hard disc drivers from somewhere first so you could use them in the set up process. I've never done this either! Is this still an issue with XP SP2 (I have a full install Windows XP Pro SP2 CD). If so, could someone outline the details for me or point me in the right direction web wise.
View 3 Replies
View Related
Jun 9, 2008
STOP 0x00000050 (0x8CCC1345, 0x0000001, 0x808A65A1, 0x00000000) These both happen when installing windows, either when at 95% of copying files or when booting into windows.
View 7 Replies
View Related
Aug 14, 2007
Currenlty got an issue where i have a user who wants to dual boot with Vista and XP using sata disks.The general rule of thumb when doing dualbooting is to install the oldest operating system first, and then gradually work your way up.The way it will be setup is as so Vista - Primary partition of the 1st disk
XP - Primary partition of the 2nd disk.Now, The way i was thinking of doing it was to install XP first, then install Vista, And modify the boot.ini to find the entry for XP.Is there any difference in modification of the boot.ini file when using sata drives, and is there any difference when making mods in Vista (As i have only edited the boot.ini in XP)
View 1 Replies
View Related
Sep 8, 2007
I have a computer at home with two identical 160 GB WD SATAII drives in it and I want a copy of XP on each drive. The first drive (Which I have been using as my gaming computer) has already got XP installed and I want to keep it pretty much free of anything but games so it won't affect performance. On the second drive, I would like to install another copy of XP and use this drive for my common use and with the primary intent of using it for a HDTV capture device. I've researched it for a while and have almost only been able to find information concerning dual booting with IDE drives using a jumper switching device so you don't have to dismantle the computer every time you switch drives.
View 11 Replies
View Related
Sep 2, 2005
Used to use Barts PE on a Windows XP system that had IDE drives. Created a new one since I was getting an error on my new Dell System with Windows XP PRO. Said it could not find a certain .in file. So I created a new Barts PE using a Windows XP Pro CD with SP1 and a blank CD to write the ISO image. After rebooting with Barts PE CD with ISO image, it looked fine and booted okay into Barts PE---BUT---it could not see my hard drives.
View 5 Replies
View Related
Jul 1, 2010
I'm trying to dual boot Windows XP Pro 32-bit and Windows 7 with Windows 7 installed first; but this isn't the problem.
The problem is trying to boot Windows XP so it can install. I booted XP from an installation CD, then a blue setup screen appears, with some files apparently being loaded at the bottom of the screen (this is around the time pressing F6 to load drivers comes up). Then boom, I get blue screened with this error and cannot proceed:
A problem has been detected and windows has been shut down to prevent damage to your computer.
View 14 Replies
View Related
Feb 24, 2008
So I'm using my a8n-sli premium motherboard and have been just using 1 sata hard drive using Windows XP for about a year. I bought a second sata hard drive last week and installed Vista on it.I just can't figure out the correct boot.ini for this to work,I get an missing NTLD message, when I try to boot from Vista, but the XP one works with that configuration.I can boot off the Vista one fine if I set it in the bios boot order to come up before the XP hard drive, so the drive and the OS are fine
View 3 Replies
View Related
Aug 5, 2009
I've got this old mobo Abit VT7. I want to install XP on it. However, the XP disc doesn't recognize SATA hard drives. So I downloaded official SATA driver from the Abit website http://tinyurl.com/kua5qz and tries to slipstream my XP disc following the instructions set forth here http://tinyurl.com/37anvn . I am not too clear how to incorporate the drivers from the official drivers, but Nlite seems to be able to find the drivers once I pointed it to the top unzipped driver directory, and I selected the XP folder for it. However, the newly created XP disc still fails to recognize the SATA hard drives. Alternatively, I believe I could have a boot floppy which would load the drivers in, then I launch the setup in the XP installation CD via command line. But I don't know how to create a boot disc which has those SATA drivers in.
View 6 Replies
View Related
Apr 8, 2010
How do you fix BSOD and Stop 0x0000007E error?
View 1 Replies
View Related
Jan 3, 2009
computer has a BSoD, Stop error 0x00000024. Many of the guides on the Internet told me to run " chkdsk drive: /f " in Cmd. The problem is that I CANT go past the BSoD to access Cmd, even in safe mode. It is a Windows XP Home Edition.
View 2 Replies
View Related
Jan 9, 2009
The computer I am working on is a Compaq Presario SR1020NX running Windows XP Home Edition. It connects to the internet via a Linksys WMP54G adapter. It tried to install Windows XP SP3 and it failed. While the update was trying to work correcting the changes it made it froze so my b/f powered it off. It rebooted just fine and he was on the internet for a little bit and then it stopped working. We recycled the modem and the router, I reset everything. Tried to uninstall and reinstall the adapter and nothing worked. I contacted Linksys and we tried to use WZC to connect to no avail. After troubleshooting a little more we determined that it had to do with the updates that were just installed on the pc. The tech suggested removing all the updates that were just installed and try again. I tried...but that is where everything went heywire. I uninstalled the first update and rebooted.....then got a blue screen flash up that said autochk program not found - skipping autocheck and then went to an endless boot cycle. I couldn't boot in safe mode, tried last known good config and nothing worked.
View 2 Replies
View Related
Nov 13, 2009
my inlaws have a gateway with XP media on it. they told me that the machine said it was updating and going to reboot. after that it never rebooted. when they turned it on they got a reboot loop going. when i looked at the error msg it was the 7e stop error. with nothing else i did a search but just could not find anything like this. i can not boot into safe mode or normal mode. i have done a chkdsk /r /p several times but still no go. i have taken the HDD and was able to clone it with acronis to a larger drive. i put the HDD in a different pc and same thing.
View 8 Replies
View Related
Aug 21, 2007
I am getting a BSOD and the error says: PAGE_FAULT_IN_NONPAGED_AREA STOP: 0X00000050 (0X81000078, 0X00000000, OXF9E129BD, 0X00000002) spooldr.sys - address f9e129bd base at f9e11000, datestamp 469e788d I tested to see what drivers are not digitally signed because I read somewhere to check that and it said that the omci.sys and tcpip.sys are not digitally signed. I am testing all the hardware as we speak with PC-CHECK, the RAM seemed to pass all the tests. I can log in to safe mode and I tried restoring to a previous date and it worked for a while. I was able to uninstall the McAfee Antivirus which I thought might be the problem, but still BSOD...
View 14 Replies
View Related
Aug 11, 2008
I have a user who is getting a blue screen that references the following stop codes;
0x000000C2
0x00000000
0x80000000
I looked around but it seemed like a lot of people's issues were resolved by replacing the memory. So here is what I did;
The laptop is an HP 6710b;
- Completely replaced the memory - BSoD still happens
- CHKDSK /F - BSoD still happens
- Latest patches removed - BSoD still happens
- take hard drive out and put into a different, identical 6710b - problem resolved.
| BIOS version is the same on both laptops
View 14 Replies
View Related
Oct 26, 2008
My system randomly freezes and sometimes the screen will go blank When i try and start up the system i usually get stuck on the loading screen and have to restart, or the system will freeze as i'm logging in. I get a BSoD with DRIVER_IRQL_NOT_LESS_OR_EQUAL 0x000000D1 (0x000000000 0x0000000FF ) and some other 0x000stuff
View 6 Replies
View Related
Aug 24, 2008
An app was installed, and right after, a BSOD came up with the following error message: A problem has been detected and windows has been shut down to prevent damage to your computer. If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.
Technical information: *** STOP: 0x0000008E (0xC0000005, 0xBF803EF6, 0xF70917c4, 0x00000000) *** win32ksys - Address BF 803EF6 base at BF800000, DateStamp 43446a58 Beginning dump of physical memory. Physical memory dump complete. Contact your system administrator or technical support group for further assistance......
View 1 Replies
View Related
