I connect the sata Hard Disk throw usb cable.after that i am not able to access the Hard disk.It is ditected in Disk management, but not able to see in My computer.I tryed ti initializa the HDD but it getting error.i get below error.
"the request could not be performed because of an I/O device error"
i was watching a movie on my laptop, all of sudden my external hard drive stop working. i can not see it.
View 1 Replies View RelatedBackup keeps giving me this error now out of the blue 0x8007045D "The request could not be performed because of an I/O device error". I've done the disk check (finally) and it came back clean. I've tried the shrink volume tactic as well, which of course didn't work. I'm trying to do this back up on an HP 500gb external drive?
View 4 Replies View RelatedI'm having trouble with my hard drive, it's a WD elements 320gb hard drive and when I try to put anything on it or take thing off it it give me this message saying it was unable to do it because of an unexpected error "error 0x8007045D: the request could not be performed because of an I/O device error" I have some important files on this hard drive.
View 1 Replies View RelatedI have been trying to back up all my important data onto an external hdd. The external hdd i am using is a WD 2tb. I am currently running Win 7 x64 with 2 x hdd wd 2tb set-up in raid 1 for hdd failure. I would like the external one as a backup weekly in case of file corruption. However when i go into setup, i get the following msg "The request is not supported" Error 0x80070032. I have read through a few threads on this forum with regards to task scheduler and event log they all seem to be set as required. There is also suggestion that win 7 may not be able to handle large hdd sector size, something about 4k versus 512.
View 2 Replies View RelatedTech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i3-2350M CPU @ 2.30GHz, Intel64 Family 6 Model 42 Stepping 7
Processor Count: 4
RAM: 6037 Mb
Graphics Card: Intel(R) HD Graphics 3000, -1988 Mb
Hard Drives: C: Total - 454779 MB, Free - 395876 MB; D: Total - 21855 MB, Free - 2354 MB;
Motherboard: Hewlett-Packard, 1819
Antivirus: Norton Internet Security, Updated and Enabled
Printer HP Photosmart 5514 B111h / Network Status: Ready / Active Connection Type: Wireless
error 1053: The service did not respond to the start or control request in a timley fashion Also before a message / Windows cannot connect to the printer. The local print spooler service is not running. Please restart the spooler or restart the machine. Does this mean to connect a USB cable and reconfigure the wireless connection.
when i want download anything it can not performed.unable to download message are displayed what i do?
View 1 Replies View RelatedI was having some problems with my computer. Seemed like it had a minor virus that my Norton wasn't getting rid of. I have all my files backed up so I decided to start with a clean slate and just restore my computer back to factory settings.i have a Dell Inspiron laptop. I performed the Dell DataSafe Restore and Emergency BackUp. I followed all the instructions and everything went fine. It told me it was successful and to restart the computer. I restarted and now Windows 7 will not work.i turn my computer on and a screen comes up that says "Windows Error Recovery" it gives me two options to "Launch Startup Repair" or "Start Windows Normally"... Starting normally just sends me backwards. I tried the Start Up Repair and it begins to run and then I get an error that it can not repair. There are some problem details/signatures if that is helpful but I don't understand them.I can't run in safe mode. I never made a set of recovery discs, I only have the disc the computer came with (drivers and software installation).
View 6 Replies View RelatedI have an emu 1820m soundcard installed in my computer. It seems to be functioning perfectly. I can play dvd'd, cd's, iTunes, etc and the sound plays through my speakers without a problem. I want to record some sounds from a dvd but i cant get anything to record. Recording device is set to Wave EMU DSP as the default device. Im using Audacity to record and have set the recording preference device to be Wave (E-MU _-DSP). When I hit record I get an error 'Error while opening sound device. Please check the input device settings and the project template'And I cant record anything.In the built in Windows sound recorder, when I hit record, I get this error 'An audio recording device cannot be found' Everything seems to be functioning perfectly, yet i just cant record anything.
View 8 Replies View RelatedI've got Visual InterDev 6 installed using Seamless XP Mode.If I open a file on the host disk, which opens interdev I cannot save any changes, and I get this error:"The requested operation cannot be performed on a file with a user-mapped section open" If I save to a new file in the same folder, it saves ok, but any subsequent edits return the same error if I try to save.Is this a permissions problem with windows 7 and XP mode, or a quirk with the old interdev software?
View 1 Replies View RelatedI want to check my hard drive for errors, and go through: C/Properties/Tools/ Error Checking/Check Now , etc., but when I do this, I am told that I have to restart my system before it will run. But when I either simply Restart, or Shut Down then restart, the CHKDSK does not run. I am using Windows 7 Home Premium.
View 3 Replies View RelatedI am using W7, home premium on 1 year old HP desktop computer.Recently, I was having trouble accessing videos from you tube, email and other sites. I had been using adobe flash player 9 and I was told to upgrade adobe flash and to get version 11. I installed version 11 but it would not play until I lowered my privacy settings from medium high to medium per instructions on Adobe. The flash player worked after that except now I am constantly getting the following message everytime I launch IE 9 and every time I go to a web site. The error message is always similar to this -"Privacy Alert The website (AZh).com has requested to save a file on your computer called a cookie. Do you want to allow?Allow or block"I am currently getting this message many times a day. No matter if I select block or allow, they keep coming back. This happens on all sites and often is unrelated to the site I am visiting.
View 3 Replies View RelatedBasically.. I have a orange LED light that blinks like crazy when I'm downloading something.. but what's wierd is.. Once I've finished the download, Sometimes.. It just keeps blinking forever!
That tells me that it's downloading from somewhere and I can't tell from where exactly.. Luckily.. Uninstalling the wireless driver & reinstalling it solves the problem but it tends to come back eventually..
So what I am requesting from you fine people here @ SevenForums is for some type of Internet Bandwidth Monitor which I can use to see where my laptop is downloading from & hopefully stop it completely so that I may use my broadband speed for something more.. For me & less for what I don't want.
driver for magic mouse for macbook air for windows 7 operating
View 1 Replies View RelatedI am using FreeAgent Go 5oo GB , when I try safely remove FreeAgent Go always show the error massage " Seagate FreeAgent Go USB device can not be uninstalled right now because the system request system restart " and I have to restart every time.I have already tried the following :
1. Close all application and end recent file process.
2. Check " don't remove file to the recycle bin, remove file immediately when delete" in the recycle bin.
3. Disable write caching on the device in devive property "policy" tab.
4. Using third party sync.exe to flushes disk buffers together with HotSwap!.exe yet still shown the same error massage.
I run a web server from my laptop, and my IP address (location) gets updated via DynDNS.org servers.My notebook is always behind a NAT-configured LAN, and I have configured the router firewall to pass port 80 service requests to my IP (usually 192.168.x.2, where x is maybe 0 or 1 or whatever.I use NetSetMan for location based setting).the DHCP server is configured to stay away from static addresses in the private LAN.Most routers have their own port 80 service, the configuration interface, accessible by hosts inside the LAN.I don't have a problem with port 80 service requests coming from the WAN getting passed to 192.168.x.2 host running the web server.BUT, users in the 192.168.x subnet requesting service from within the LAN do NOT get delivered the web page from host 192.168.x.2, but instead the router's configuration interface, if they use the host NAME. Of course, if they use the host IP address, they get the content.What is happening of course is that if anyone uses url..., it goes to DynDNS.org where the IP is resolved to the address a.b.c.d, the WAN IP address of the router I am currently connected to. So the http client bundles the packet to the destination a.b.c.d:80.The users INSIDE the LAN get the router configuration interface web page when they type in a.b.c.d:80, but not users OUTSIDE the LAN (in that WAN).
View 6 Replies View RelatedI use a windows 7 OS and on january 25, 2013 my computer possibly downloaded a virus or something. I know my way around the computer on an intermediate level but cannot find any strange exe files. I have nortons and it did not stop this download. I think my files are on the computer since 300GB is still being used on my harddrive.
View 1 Replies View Relatedif i have posted inthe wrong section in apologis, I am using MSN Live 2011 When i get asked for Remote assitance my client always disconnects and then says reconnecting in 59 seconds. The end requesting it gets the pass pages etc but by the time they put it in i have dicsonnected and reconnected by which time the seesion is invalid, I have the correct ports open and also tried all the advice i can see and find online.
View 3 Replies View Relatedmy problem is >> if I entered my security key of wireless at any laptopit saved the pass and connect automatically without requesting it again
View 2 Replies View RelatedI have installed windows XP mode for windows 7 and it works fine. I have even installed few apps that were not possible to be installed on win 7. I played with win 7 virtual PC and have few questions:
1. I see that system chosen 120 GB for this virtual Win XP, I was not asked about this and wonder if this could be changed. The originally C: system partition in win 7 is 300 GB.
2. When I use cmd command in run and type ipconfig, I see that correct IP address is displayed (192.168.1.65) since it works in private network and internet is working OK. But when I try to ping router (192.168.1.1) I get message that "request timed out" occurred. Of course, ping works in windows 7, and I have internet access in both win7 and virtual win xp.
On startup, my browser has started automatically and attempted to open the page.[code]I have tried searching the internet to find out what this relates to but there seems to be nothing mentioned. The website itself doesn't seem to exist (I get the normal 'This webpage is not available' tab). I have checked all of my browser settings and cannot find anything that references it.I thought it may have been related to the Kana Reminder program that I have, but I have been using that for many months without this coming up before.Or somewhere else I can check? I'm thinking that maybe something is in my registry but I don't want to go fiddling around without knowing exactly what I'm doing.
View 9 Replies View RelatedI just started up my Laptop (Sony Vaio 2.6GHz Core i5 | 4GB RAM | ATI Radeon | Windows 7 Home Premium) and none of the programs on my laptop are responding when I click on them to start them. Not even Windows Explorer opens. Nothing responds. I can open the windows start button, but that is about it. The PC is still under warranty, so it's quite new (4months). I also take great care of it, I do not load all sorts of crap on it. Only the essentials.It all started yesterday, when my PC became really slow and I had to restart it, where it literally took 10 minutes too shut down (NO windows updates being installed...). I restarted it, ran a check disc for bad sectors, and it found none. Only a few bad clusters. I also ran - sfc /scannow command in cmd. However, when I open some of the programs(non windows system programs such as explorer and task manager), it gives me the following error: "The service did not respond to the start or control request in a timely fashion".
View 7 Replies View RelatedI have a multi-users Windows 7 (64bits) system, with one Administrator priviledge accounts, the others being non-admin. Disk is partition with system on C and data on D and E.
All users can access to D and E.
How to enforce security properties so that delete file or folder on D or E must prompt for admin password? I see that I can totally prevent DELETE, but I just want to permit delete, when user successfully entered admin pwd on prompt.
If I right-click on D: Then properties and view security tab, I see 4 groups:
* Authentified users
* System
* the admin account
* users (the admin account as user)
I recently did a clean install of Windows 7 x64, and my I cannot install from my DVD drive. When i attempt to open the drive in command prompt it gives me an I/O device error message. I can open media disks with no problem, and the drive appears in both device manager, and windows explorer. I've attempted to find the firmware for the driver (mat****a UJ-840s) but I have not been successful. One more note I went from a 32 bit XP to the 64 bit windows 7
View 5 Replies View RelatedI installed Ubuntu side by side to my win 7. On the install it would only install to an external drive I have. After the install completed an I restarted my computer and I got an error message=" error: no such devive: 868152e-2012-469b-b469-ebc2c953dfb4.grub resue>"I restarted my computer a few times and kept getting the same message.I decided to restore my computer back to factory defaults. After doing this I restarted my computer but kept getting the same message.
View 2 Replies View RelatedI have a laser projector, and i control it with my windows seven notebook by usb.
Problem is, sometimes by a static shock of other devices or by other causes i do not know of, the notebook suddenly refuses to work with the usb drive anymore and the projector freezes.
but here is the part i want to solve. after replugging the usb drive windows says that the usb device is not regonised.... after plugging out and waiting 2 minutes and then replug makes it work again...if i do it sooner then usally it still shits about the device not being regonised.
Recently, I've started getting an error which says: "Your USB Composite Device can perform faster if it is plugged into a hi-speed port" "The hubs shown in bold type have free ports that can support the HI-SPEED USB device"
It then lists two bolded options for a hi-speed ports: A USB Root Hub with 6 ports, and another with 4. This error occurs on both my Windows 7 equipped Dell XPS15 (which has 2 USB ports) and an older Dell laptop which runs Vista (3 USB ports)
This is shown after my external drive (a seagate model) disconnects from my computer, which usually ends poorly for me, since I typically run Photoshop off my drive.
I'm wondering if these errors are caused by a new USB splitter I bought. It has 4 ports, but the model year and quality of the thing are dubious at best; my webcam and wireless mouse are also typically attached to it, and the webcam disconnects at the same time as the external drive. The mouse still works though, so that's pretty mysterious.
Every time im exploring my fone's memory card,or any other kind of storage like usb memory sticks, the window explorer closes down, and i have to open it agin,locate the folder i was on,but then it will happen again.
If i check Event viewer (System bit)it generates the following event: An error was detected on device DeviceHarddisk2DR2 during a paging operation.
Is my hard drive working ok?+ i noticed that my computer works slow,when im on windows explorer,going to my music,etc...
any help?
I just bought a amd phenom ii x4 955 and a asus m4a88tm le motherboard . After that i formated my hdd and installed win 7 ultimate and amd motherboard drivers. Now when i connect a usb device it shows Unknown usb device (except my mouse and keyboard).
View 6 Replies View Relatedmy bluetooth is not working .. my dell model is inspiron n5110..
View 1 Replies View RelatedI have an Acer Aspire On 10inch Notebook that runs on Windows 7 Premium Edition (32bit). I'd been having some troubles with its speed for a day or so and since I'd neglected to do a Windows update. So, I restarted it and hoped that once it installed those updates everything would be fine. My first warning sign was the time that it took to turn off - probably 15 minutes was spent with the screen continuously saying "Shutting Down" and I took this to mean that it was probably a series of updates that I had missed. So, I left it to sit and came back to check on it afterwards.When it finally finished, a black screen took over and sat there for quite some time. Eventually I grew frustrated and restarted the computer, and saw the 'Acer' screen come up, and then the computer screen went black again and a command line started, where I received this message[CODE]
View 3 Replies View Related
