Error Code 6 - Setup Was Unable To Complete The Installation
Nov 1, 2009
i recently installed windows 7.. when i installed VIA drivers for graphics it didn't get installed properly... i had the message "setup was unable to complete the installation (error code-6) ".. so i was asked to upgrade my BIOS... i downloaded it and installed it... when i ran the update, the system just hanged up and nothing happened for hours,..
so i had to restart the system and went to BIOS settings and clicked load optimized settings,,,.. from then onwards my OS is booting until the windows startup screen appears and just hangs..it's not booting to the users login... but it logs in at times... i dont have any restore points too..what to do?
I have my HP Laptop which came with Windows Vista as the OS. I want to upgrade to Windows 7 so I bought Windows 7 from my local store.I entered the disc and did boot from CD. It reached to the page where it shows the disk partition. I deleted the partitions and created new one. However, whenever I create the partition, it creates a primary one and gives me saying Setup was unable to create a new system partition or locate an existing system partition.The stupidity that I did was deleted the partition which had the Recovery Drive in it. So, now I am stuck and not able to install Vista as well as Windows 7. I am not able to boot Windows as there is no OS in my laptop now.
I am trying to install my windows 7 and it wont complete the setup. After all the files load from my original disks, the computer restarts and starts the setup but its been a blank screen for over 2 hours now and still nothing. I can use the restore from an image file and it sets up in 30 minutes and works but i have no home group setup and cant read some external hard drives right so I wanted to try a clean install. The computer is a Gateway 64 bit.
- build a system with 1 WD1101FALS HDD and installed Windows 7 64 bit no problem. All was good for few days until I got a bug to set up a RAID 10.
- Went out bought 3 more of the same drives. All 4 drives are WD1101FALS 1TB.
- Set up the RAID 10 array on the ASUS motherboard, got the RAID drives for Win7 64bit on a USB key.
- Start install, no problem. Win7 asks for drivers, I click browse and select the drives from USB for the RAID. Install continues, files are copied, thing are flying, it's fast.
- Then 1st re-start
- Windows continues to install (finalizing things, registry update, etc).
- I get to 4 check marks on the Windows Install screen and then it goes into the last step "Completing Installation". The progress bar goes to about 80% complete and then
BLACK SCREEN, computer re-starts. Windows comes up with a message "The computer restarted unexpectedly or encountered an unexpected error. Windows installation can not proceed. etc.." It assks to press OK and and PC re-starts and the installation re-starts from scratch. I tried about 15 times, with different RAID drives, from XP to Vista, to Win7.
I have no clue what else I can try. Usually people have problem with the RAID drives but I have no problem with that step. The drivers are selected and seem to be working fine. The install almost completes.
Here are the images on how far along the install goes. The progress bar actually goes more than that, I just took a picture before the black screen.
Setup is starting services.Windows could not complete the installation. To install Windows on this computer, restart the installation.About one month ago I decided I wanted to have a clean install of windows 7 on my acer machine. I did this by using an acer made pre-installed program. It claims to be very straightforward, all you have to do is click a button and they will reinstall windows 7 for you and even back up all your data ,so that after the clean install you don't lose a thing. Sounded great but in reality it has stopped my notebook from working.I am now in a circle-jerk of the error message I stated in the beginning of this topic. Once my computer restarts it just gets me the same error message again. I tried booting from a bootable USB-key with the windows 7 iso downloaded from official sources. But this did not do anything from me. I also went to acer support in my city. They offered me to fix it. All they had to do is copy all the info of my hard drive I wanted to keep and do a fresh install of windows 7. Would take them 3 hours. This is the easyiests option for me. But problem is I live in China and I don't trust those tech support guys for good reasons. I went there with my laptop, the tech-support guy put in a usb-key and started up my computer. It started some kind of diagnostics. After 20 minutes of this he stopped the diagnostics and started running some chinese software on my computer. Presumably booting from the USB-key. After a couple of clicks he was browsing around on my hard-drive. I was right behind him and could see him every move. He was snooping around my folders looking for all sorts of personal stuff. He was going to folders he had no business going to. I think he thought I had no idea what he was doing or would not recognize he was snooping around on my computer. At one point he went into a folder and told him not to go there in chinese. He quickly exited, but then couple of seconds later went back to that same folder to do some looking around. Presumably cause he thought I would not notice. So I do not trust these people one bit. And would not want him to copy all the info of my hard drive to then re-install windows7.
I have a Win7 ultimate 64bit I recieved from a friend. I assumed it was one of his Microsoft apps he gets in his MSDN subscription for free. Anyway, every now and then I would get these pop-ups from Microsoft saying its not genuine. He would give me a script to run that would fix it, until it would happen again.Bottom line I foud out later this was pirated software so I purchased a normal copy (win7 pro 64 bit) to do a reinstal of the software, BUTTTTT now I can't do it because I keep getting these errors saying "Windows was unable to create the required instalation folder 0x80070005". I know the last update for the pirated copy was something to remove "RemoveWAT.exe". I tried to do a restore in Win7 to a previous state but it errored "0x80070001"Any advice on what to do. I don't want to have to reformat the whole drive, because this was a dual boot on a new MAC so I could boot in iether MAC or Win7.
I am installing Windows 7 (Custom installation initiated from Windows XP) but I get the following error message when the installation is on the "Installing updates" step of the installation:
"Setup cannot continue due to a corrupted installation file. Contact the vendor of your Windows installation disc or your system administrator for assistance."
Do you have any idea what the problem may be with the installation? Is there a way to see what file that may be corrupted?
I have tried to burn the DVD in low speed, but the error appears anyway. I have a MSI K8T Neo2-Fir mainboard and the Windows 7 upgrade advisor application says that my hardware is okay for upgrading.
I have my HP Laptop which came with Windows Vista as the OS. I want to upgrade to Windows 7 so I bought Windows 7 from my local store.I entered the disc and did boot from CD. It reached to the page where it shows the disk partition. I deleted the partitions and created new one. However, whenever I create the partition, it creates a primary one and gives me error saying Setup was unable to create a new system partition or locate an existing system partition.
We took his computer back to factorysettings however when the system is trying to install Windows 7 we keep getting an error: Windows could not complete the installation. To install windows on this computer, restart the installation.How would I do that? I have tried safe mode but it won't let you install in safe mode, when shutting off the system or restartingit always gets to setup is starting services page and then the error message.
I attempted to install Windows 7 x64 RC version on my new desktop, and about 20 minutes into the "Complete Installation" section my computer crashed for a reason of which I'm not aware (I saw a blue screen with writing for about a second or two before my computer restarted). I now get the following error after windows attempts to "start services":
"Install Windows. The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install Windows, click "OK" to restart the computer, and then restart the installation".
I've now clicked "OK" about 10 times, with my computer restarting properly each time, and the same error pops up every time.
Recently I went to restore my netbook-Acer Aspire One Happy 2. Well I clicked save user data to C: drive, for me a first time user of a netbook...didn't know that if I clicked that and was using a different windows 7 edition from the OEM. That a different windows 7 edition data couldn't be saved. Now, whenever I boot up my netbook, windows will try to install on my computer but gives error:
Error message: Windows couldn't complete installation. To install windows, restart the installation.
System Specifications: Pre-load: Windows 7 starter Os using before system restore: Windows 7 Professional CPU:Intel atom N570 @ 1.66ghz Graphics card: Intel Gma 3150
When attempting to backup a system image and/or selected libraries or files on an OEM installation of Windows 7 Home Premium 64-bit, I am receiving an error message. The initial pop-up states: The Last Backup Did Not Complete Successfully When I click on the pop-up to check the backup and select �More Details,� I see the following message. The System cannot find the file specified Error Code: 0x80070002 No additional information is provided. (And no clue is provided regarding what �file� is not found.) While I am attempting to backup to an external hard drive connected via eSATA, this error also occurs when I attempt a backup to either an external USB drive or a DVD.
I have attempted to run various backup scenarios wherein [a] Windows selects what to backup, [b] I choose a system image only, [c] I choose libraries only, or [d] I choose a very small data directory in a directory outside of the libraries. The error is always the same. When the system image is included, the backup does run for a time before the error message occurs � and a significant amount of data is written to the drive. When I run a file-only backup, the error is almost instantaneous. So far, in attempting to resolve the problem I have taken the following steps (although not necessarily in this order): Confirmed the registry profiles image paths are accordance with the information found at: The Storage Team at Microsoft - File Cabinet Blog : Common causes and solutions to Backup, System Restore, and Complete PC Backup problems - updated!. Everything was correct, no problems found. Ran the system file checker (sfc /scannow) with no errors reported. Scanned all hard drives (chkdsk x: /r) Confirmed that VSS and Windows Backup Services are running via services.msc Although I didn�t think it applied, I tested the Hotfix suggested at: You encounter problems when you move data over USB from a Windows 7 or Windows Server 2008 R2-based computer that has an NVIDIA USB EHCI chipset and at least 4GB of RAM. No success. Reviewed the information at Error code 0x80070002 when you back up files in Windows 7 however the scenarios did not apply and therefore the solutions were not available to me. Checked the error logs at C:WindowsLogsWindowsBackup, but the error log is empty . Ran a Clean Boot via msconfig.exe Attempted to run Backup in Safe Mode, but of course Backup & Restore cannot be run in safe mode, even if I try to start the services manually (Error 1084). Reset Backup Files Configuration, using instructions at: Backup User and System Files - Reset to Default Configuration I am extraordinarily frustrated. This is a new computer, and an almost new installation of Windows. I have obviously missed something, but don�t know what it is. I am desperate for a solution.
I m reinstalling window 7 on my new laptop ..previously it got 000000f4 error blue screen appers and it restarts all the time so i decide to reinstalll it..so when i reinstall it setup was working fine but at the end it got setup.exe error ..i thought may be cd is corrupt ..so i bought new cd now when inset a cd it appera press any key to boot from cd han i presss any key than window is loading file after that window is starting up appers than it is frozen their why .
No matter how i try it I mean an upgrade or a clean install this is the error that i get : windows installation encountered an unexpected error verify that the installation sources are accessible and restart the installation error code:0xE00000100
not sure what this means.... has anyone else had this show up for them... if so whats the fix?
I'm having Athlon XP 2000+, 1 Gig Ram, GA-7VKMP-P,Seagate 80GB (7 Yrs old build) running with Windows Pro XPSP3
Last Saturday, I tried to install the Windows 7 Professional ( Downloaded from MSDN). When tried to boot from DVD it said " Windows Cannot Boot From this drive. CODE- 5".
I tried from my another DVD drive. Same Error.
Changed all possible jumper settings for HDD and DVD-RW's ( All IDE) as Pri- master/Slave, Sec Master/Slave. Nothing Worked.
Also I tried with another copy of Win 7 Home Premium came with my Dell Laptop (Worked fine for fresh installation in my laptop). Still same Error.
But I'm able to install both Windows 7 Home Premium and Professional in the same system, starting installation from XP (Not Booting from DVD).
Now I installed Windows 7 Pro as I said and after that I deleted Windows.old folder. All running fine.
With some curiosity, I tried to boot again from DVD drive with Windows 7 Dvd, same Error, even after installing Windows 7.
Till now I don't Know how to perform a clean installation of Windows 7 in my system.
So This is my 3rd install disc I made and I Re-downloaded 64 bit windows 7 no problems. Integrity was checked and successful. I burned at the slowest speed 2.4x Also no errors.
Once I go to install windows 7 it jumps to 8% then 100% then i get an error saying Files are missing or corrupted. I don't see why I should have this problem since downloading and burning process went smooth.
the error code was 08007017.
I also disabled my norton or most of it.
Anybody have any ideas whats wrong I only have about 2 more discs left to burn.
I have this problem with my Toshiba laptop: Several days ago my com crashed, when I started my computer on the very beginning on start up screen when it says windows is starting I get a 1 second blue screen with some saying and my laptop restarts by it self. So, ok I have Windows 7 Ultimate installation dvd and i tried to install it,everything goes well untill on the second line of the very beginning of windows installation 98% I get this message Error Code: 0x80070570.
I've read some forums people were saying that this could be a RAM problem,so,ok my toshiba have 2 RAMS x 2 Gb..so i taken out 1 tried to install-same error, put in another slot-same error,replaced and putted my other Ram Memory in the slots same again. So,is there any solution how to fix this?i can see in bios that bios is reading my HDD,not sure if its working,does that mean that if BIOS is recognizing my Laptops HDD that works 100%?
I have been encountering this same error code in one of my machines. I get the Error Code: 0x8007050 during installation of Win 7 Ultimate 64 Bit. It occurs during the expansion of files phase, during instalation, with the message "Windows cannot install the required files. Make sure the required files are available..."
Machine Specs: Intel DP43TF MB Intel Quad Core 8300 CPU 4GB OCZ ATI DDR2 RAM Antec 500 Watt PSU Hitachi HDS725050 KLA360 HD and later a Seagate ST3640323AS HD.
In previous installations of Win 7, I've observed that about 29MB are copied to the System Reserved partition. In this scenario, only 11MB are copied. I've performed the following trouble shooting in order:
- Changed out the DVD drive. Tried installation again without success. - Performed factory system restore on the hard drive. Tried installation again without success. - Replaced the hard drive with a new one. Tried installation again without success. - Removed all PCI cards, and tried again with just the PCI-E video card. Tried installation again without success. - Replaced the PCI-E video card with a PCI card. Tried installation again without success. - Cloned the "System Reserved" partition from another PC with a functioning install of the same OS. Tried installation again without success.
It should be noted that this specific machine was previously running Win 7 Ultimate 64 Bit. I was simply attempting to upgrade the hard drive. I've also tried to install Win 7 Home and Win 7 Pro, all with the exact same error code, which occurs during the same phase of installation. I also tried to perform an Upgrade install. The machine accepted a complete install of Win Vista Ultimate 64 bit (twice), but had the same error codes appear during the Upgrade install to Win 7 Ultimate 64 Bit. I reformatted and reinstalled same Vista 64 bit OS. I tried to install Win 7 Pro 64 Bit, and again encountered the same error codes. Incidentally, I have used 3 different Retail Win 7 install media. The machine passes all MemTest and CPU diagnostics.
I am trying to install Microsoft Network Framework v.4 (x64) and I keep getting error "Final Result: Installation failed with error code: (0x80070643), "Fatal error during installation" (Elapsed time: 0 00:01:01)." The exact log file is attached: Code: OS Version Information:
OS Version = 6.1.7601, Platform 2, Service Pack 1 OS Description = Windows 7 - x64 Ultimate Edition Service Pack 1 OS Version Information
and this is the code from the blue screen itself stop 0x00000116 (0xFFFFFA8009B434EO, 0x000000000000000?, 0x0000000000000002) i took a picture of it with my camera but missed that last digit thus the ? below that on the screen was this
atikmpag.sys - address FFFFF88000E5340C base at FFFFF88000E4C000. DateSt?? 4da507aa
im lost i tried searching these codes and some came up with random stuff (some of it worried me like the remote access stuff) and others dont seem to exist at least in a googleable database?
I have attempted to update windows 7 with the :Security update for windows 7 for X64 systems (KB2619339) with only failed results.the error code is : 8007065E I have CBS logs WINDOWS resource protection found corrupt files but was unable to fix some of them.
Just today I decided to download the Windows 8 consumer preview and setup my PC to dual boot with it.I am running Windows 7 home premium 64bit and the 64 bit windows 8 on my other partition. After setting up a separate partition on my hard drive and loading windows8 to this partition, I was all up and running. I had no problems setting up or running windows 8, the problem came when I booted back to windows 7 for the first time. When I booted into windows 7, I was getting the "unable to identify network" error, and no network connectivity.
First thing I tried was simply disable/enabling my network adapter thinking it was just some hiccup. No luck there. Next I pulled the power from my router, and let it completely reboot. Still no luck. I then shut down my pc and booted back into windows 8 and sure enough I am able to get internet connectivity when I am running windows 8. This got me to thinking that when I loaded windows 8 there may be some new drivers installed for my network card that are somehow causing issues when I load into windows 7 again. Not sure how this is possible.
I was under the understanding that when I loaded Win8 to the separate partition that it would keep all it's drivers and settings there and not effect anything when I was loaded back on windows 7 (This logic could be completely wrong, I don't know). So I rebooted and loaded back into windows 7, went into device manager and uninstalled both network adapters and drivers, and rebooted into windows 7 again so it could re-discover and setup the network cards with default windows 7 drivers. This did not work either and I am still getting the same error.
I am having a problem with doing a fresh install of Windows 7. It is on a Dell Inspiron 1546 with a 150 GB hard drive. There was an original install but the computer was having issues as some files were corrupted. I used the Windows 7 disc to format the hard drive and booted from CD after restarting.
However when I try to install the new Windows 7 it sits at the part where it says: Expanding files. Then after a while an error pops up that says: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information
I tried to dual boot Fedora 18 with my Windows 7. They are on two different hard drives. Fedora 18 worked but I was unable to boot up Windows 7. Frustrated, I decided to just delete everything from all the hard drives and try to do a clean install of Windows 7 using the USB-DVD Windows tool to make a USB Windows 7 installer. I then got the following error when trying to install Windows onto my hard drive:
"Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information"
I tried unplugging the other hard drives and got the same error. I also went to the command prompt and used Diskpart and did clean all. Still the error shows up. Something that might be useful is that when I did disk list in the command prompt it showed my hard drive but with 0 free space. Not sure if this is useful but the drive I want Windows 7 on is a solid state drive but the one I had Fedora on is a normal hard drive and I had an extra harddrive that I used for storage that is a normal hard drive as well.
I keep getting this error, and following Error message when you try to install a Windows update, a hotfix, or a service pack after you perform System Restore in Windows Vista: "0x80071A91" and removing files manually did not resolve the problem[CODE]
