Windows 7 X84 Cannot Receive Wireless Signal From X64 Unless Unsecured
May 21, 2012
i just built a new Windows 7 Machine and i installed x64 bit for the first time and this is my main computer with a WRT54GL Router hooked up and i moved my old machine out to my living room, but when i try to connect to it wirelessley the x86 wont even see my network at all, i have SSID broadcast on, the only way it will see it is if i disable security and WPA2 then it shows up but as soon as i put the security back on it wont connect/see it at all. Can anyone help me i have no idea whats going on, my previous machine i had out in my living room was windows xp and it could connect to my x86 win 7 fine, but now i cannot get it to work, i even bought a new wireless usb adapter to try and it still wont see it unless i unencrypt it.
I work as a software developer and have had a lot of experience with wireless networking. I have an old wireless router (unsecured at the moment) that I have connected to a modem, provided by Virgin media. When I use a cable to directly connect to the router, all seems fine, but when I attempt to connect wirelessly I am almost immediately presented with "Windows was unable to connect to [router name]". Other people in my house (on both XP and Vista) can connect to the router without any problems, implying that it is a setting within Windows 7. HOWEVER, I am able to connect to another (unsecured) wireless router. I guess this can only mean that there is a setting on the router that is preventing me from connecting...
I just bought a Netgear WNA3100 wireless usb adapter for my HP Win 7 64 bit laptop. I have been trying for 2 and half days to figure out why my speed is slow, why i don't have a good signal, and/ or if I do have a bit of a signal to my luck, why my signal comes and goes. I don't have internet at home at the moment because I am trying to save up to go to school. I am picking up a public business signal from a block away (which I have asked for permission to use), but I only am receiving not much of a signal with the Netgear usb wireless adapter.
Is there a way to setup your computer to connect only to a specific wireless router in your area? I live in a college dorm and there are a lot of wireless connects available so I'm thinking that there might be complications with my computer with all the information in the air.
I have a D-Link DIR615 router which I've been using for the past 5 months (no problems whatsoever). After i've got my laptop from the support service I can't seem to successfully connect to my home network.
My phone can connect with no problem to my router. My laptop sees other wireless networks. This is how it goes: when I try to connect it immediately says "unable to connect" when I run the diagnostics I get the "windows did not receive any response from the wireless router" message. I can only connect after like 30 mins of changing the wireless settings (usually SSID and security) from my router + rebooting it countless times. Even then, I usually check "automatically connect" and the next day after I arrive from work, it doesn't really connect automatically and can't even connect to it (unable to connect message). Even typing a wrong passphrase when it's secured it doesn't say "wrong passphrase" but "unable to connect".
Another very wierd thing is that my wireless network disappears from the network list after a few minutes, I still see other secured wireless networks.
I can connect to a wireless network made by phone (wifi hotspot) with no problems.
my laptop cant receive or send information through wireless connection. any time i tried doin any of the above, it keep telling me i needed a peripheral driver.
I recently upgraded my wireless router from a D-link Di-614 to a Linksys e3000. A buddy of mine recommended it saying he didnt have wifi issues from the top of his house all the way to the basement. I live in a bungalo home, and so the router is on one side of the house, and my Desk and macbook pro is on the otherside. Im getting 4 bars in windows 7, its showing good connectivity, but its constantly disconnecting, even when its stable, its running very slow. When im close to the router is works perfect. I design for a living and am constantly transferring files to clients. So this has become a problem, Im constantly having to unplug my laptop and walk over to the router to send/recieve large files. Any suggestion on what i can do? Could there be something wrong with the router or my laptop ?
I have new Acer Aspire 5739G laptop and fresh Windows 7 on it.
The wireless card is Intel WiFi Link 5100.
The problem is that wireless works only in short distance with access point - max distance is about 5 meters.
In that distance everything works fine.
But if I go farther or to another room it disconnects.
With other laptops all works fine even on very large distance.
I tried such things (nothing helped): * uninstall, reinstall or update drivers * install newest drivers from Acer site * install newest drivers from Intel site * tested with xp & vista drivers * on network connection properties unchecked all things except tcp/ip v4 protocol (microsoft networking,sharing, link layer topology,QoS, TCP/IP v6 ..) * disabled homegroup * on adapter properties changed signal frequencies (1,6,11), * on adapter properties changed standard type to work with: 802.11 b or g * on adapter properties changed signal to MAX, don't use power saving * disabled Internet security, firewall * Changed access point signal broadcasting with no encryption or wpa * it disconnects from another access point the same way (problem with system not wifi AP)
Maybe something forgot to say, but there was few hours of testing and can't fix it .
I'm trying to get connected to wifi on my ds lite, but my university's wireless doesn't broadcast a wireless-B signal which is the only type a DS can connect to. Is it possible to use a router convert the school's wifi and broadcast a wireless B signal for myself?
Was getting a very weak wireless signal from the router that is 2 rooms and a hallway away (40 ft.)... It was almost like dial-up used to be...Anyway, a friend of mine suggested getting Powerline Network Adapters, HowStuffWorks "How Power-line Networking Works"I spent the money for the kit, ($99 at Office Depot), and installed yesterday afternoon. Getting a great signal now. If you can't or prefer not to run ethernet cable, this is the next best thing...
I am running windows 7 home premium 64 bit. And an atheros AR5B95 wireless network adaptor.Two weeks ago I discovered rootkit 0access on my computer, and after much hassle, performed a factory restore to fix the situation. Since then my computer has been mostly unable to detect wireless connections. I say mostly because upon occassion it will see my wifi connection, but be unable to connect to it, and it will soon drop seeing the connection moments after anyway. I performed a hard reset of my modem with at&t customer service, and walked through every possibility that it could be a modem issue. This was further proven by an additional laptop having no issue with the wifi connection, and that my laptop is having this problem with every wifi connection. [code]
New Windows 7 user and I am connected to the internet via the wireless network so it is definitely connected and still fast, however I see an orange asterisk on the wireless icon instead of the usual signal strength.
I am setting up a new Acer laptop and cannot access the internet via my home wifi network. I have 2 other laptops connected to the network and running fine. The new pc is running 64 bit Windows 7 (the others run XP) and has an Atheros AR5B93 Wireless Network Adapter. When I pan over the wireless icon in my taskbar, it says "Limited access" beside my home wifi signal.
Went to the city library today - laptop wouldn't connect to any unsecured network. The library does not offer wifi, but you can detect 4-5 several unsecured networks nearby. I wasn't able to connect to any of them. One of them said "Public" - not sure who it belonged to - but the icon beside it was not the typical signal bars. Couldn't tell what it was - looked like maybe a LAN connection, three entities connected to each other. Haven't seen that in the network list before. I could connect to that one, but after a minute or so the connection was dropped.
I've never had a problem connecting to unsecured networks. In fact, I packed up from the dud library and went up the road to a neighboring town library and connected to their unsecured network just fine.
The PC in question is a Dell OptiPlex 580 which came with an OEM installation of Windows 7 Pro x64.Is it possible to purchase a bad copy of Windows?What exactly do I mean by bad copy? I'm not talking about a pirated copy with a fake license. I mean, is it possible the copy of Windows that came installed on my system is damaged, corrupt, or incomplete? All the data on the OEM disc was transferred from somewhere, from something. When the manufacturer created this disc, is it possible that something went wrong? Why do I want to know? Well, here is my story:About two years ago I purchased a brand new PC from Dell. I noticed within the first week or so, practically right out of the box, the PC crashed and displayed a BSOD. The PC crashed again about a week later. I was a little concerned when I saw the first crash, but the second got my attention for sure. However, every time I tried investigating an error code, the probable cause was always vague. I couldn't find anything that pointed to that one silver bullet fix.I looked for answers everywhere, often on boards such as this one. The fixes suggested to me were numerous, well thought out, but all too often varied. It's the hardware! I's the software! It's a third party driver! It's Windows! Whatever the suggestion, I tried it, but nothing worked.I am not a computer expert, guru, or whiz of any kind. I'm just a guy that has been able to troubleshoot or fix numerous issues over the years with the assistance of great people who contribute to forums like this one. But in regards to this particular issue, no matter what I have looked for, no matter what test I have used, I have never been able to identify the cause of these BSOD, nor have I been able to prevent them from continuing.Here are a few things I can tell you about this PC. I don't have any weird/uncommon software installed (just your basic things like Office, Acrobat, etc.). I'm not overclocking anything. I've checked the power supply and it is fully functional. I have run more memory tests then I care to remember. I've scanned for malware over and over again. I have run diagnostics to check for damage on the hard drive. I've uninstalled and reinstalled drivers. I've run stress tests on the drivers trying to force a crash. I physically removed a graphics card that I thought might be the issue, never plugging it back in. I've opened up the PC and reseated everything. I've kept the insides clean. I've checked the temperature inside the machine. But in two years of working on this computer, I have never found a single hardware defect with this system. And not one single tweak I have made to it has kept it from crashing. Even when I reformatted the hard drive and did a full reinstallation of Windows, which was the recommendation of Dell's paid software support team, the PC quickly went back to more BSOD. If someone told me they reinstalled Windows on their system but it kept crashing, I would probably assume there was a hardware issue too. But again, I have searched and searched for evidence that the hardware is broken, but cannot find anything.All of this makes me wonder; maybe the PC arrived with the problem. Perhaps the OS was initially installed with a bad copy of Windows? Maybe when used that same disc to reinstall the OS, I just put the same problem back into the computer.It has been suggested to me that I conduct a Repair Install of Windows to fix some issues I discovered. Recently I ran the sfc/ scannow command and received a message stating that there were corrupt sectors that could not be repaired. But I am afraid to try to fix it with the OEM CD. This is the same CD that failed to fix the issue when I did a full install. Is it possible that if I use this same disc again that I could be replacing the same corrupt system files all over again?I am curious to hear feedback from others. Have any of you had an experience like this one? Is it possible that the OEM CD I received is damaged?
My friend recently installed windows 7 ultimate 32 bit on his laptop, everything went perfect and is running fine.
He then decided to also upgrade his desktop, he had successfully installed it and was able to get to the log in screen without any problems, once typing in his password and logging into to windows, the screen would flicker and go black and blue and sometimes the pc would shut itself off. The error which we could make out before the screen went off was 'Kernel driver has stopEd responding.' something to that effect, I can't remember the exact message. But we managed to figure it was an issue with the nvidia drivers, as it seems to be a wide spread problem with nvidia GeForce cards (my friend has a 8600gt). Now since then we decided to format the hard drive and perform a fresh install of windows 7. Now this wer things get interesting.
We booted from CD and ran the windows 7 installation, when the screen comes up to ask which partition/hard drive you want to install on, we formatted the hard drive on this screen and then tried to perform an installation, the installation started, but stopped at some point and we received a blue screen, now weneva we attempt to boot from cd, the windows installations files are loaded and the windows starting logo is displayed, but then we receive the BSOD.
I cannot provide you with any dump files as there is not operating system, but I have taken a picture of the BSOD that we receiving.
bought an HP DM4 yesterday an noticed there wasnt anything in the box regarding recorvery disk or windows reinstall disk.An IT co worker informed me that i should have recieved a windows disk just incase my computer OS died on me and i needed to reinstall fresh.am i missing somthing here or do i have to call hp for them?
I have a question about a desktop workstation I purchased from Dell. The PC in question is a Dell OptiPlex 580 which came with an OEM installation of Windows 7 Pro x64. Please bear with the length of my post, and forgive me if I am not posting this in the correct forum. I�m not sure if there is a correct forum for this question, but here goes:Is it possible to purchase a bad copy of Windows? What exactly do I mean by �bad copy�? I�m not talking about a pirated copy with a fake license. I mean, is it possible the copy of Windows that came installed on my system is damaged, corrupt, or incomplete? All the data on the OEM disc was transferred from somewhere, from something.
about two years ago I purchased a brand new PC from Dell. I noticed within the first week or so, practically right out of the box, the PC crashed and displayed a BSOD. The PC crashed again about a week later. I was a little concerned when I saw the first crash, but the second got my attention for sure.However, every time I tried investigating an error code, the probable cause was always vague. I couldn�t find anything that pointed to that one �silver bullet� fix. I looked for answers everywhere, often on boards such as this one. The fixes suggested to me were numerous, well thought out, but all too often varied. �It�s the hardware! It�s the software! It�s the hard drive! It�s a third party driver! It�s Windows!� Whatever the suggestion, I tried it, but nothing worked. I am not a computer expert, guru, or whiz of any kind. I�m just a guy that has been able to troubleshoot or fix numerous issues over the years with the assistance of great people who contribute to forums like this one. But in regards to this particular issue, no matter what I have looked for, no matter what test I have used, I have never been able to identify the cause of these BSOD, nor have I been able to prevent them from continuing.
Here are a few things I can tell you about this PC. I don�t have any weird/uncommon software installed (just your basic things like Office, Acrobat, etc.). I�m not overclocking anything. I�ve checked the power supply and it is fully functional. I have run more memory tests then I care to remember. I�ve scanned for malware over and over again. I have run diagnostics to check for damage on the hard drive. I�ve uninstalled and reinstalled drivers. I�ve run stress tests on the drivers trying to force a crash. I physically removed a graphics card that I thought might be the issue, never plugging it back in. I�ve opened up the PC and reseated everything. I�ve kept the insides clean. I�ve checked the temperature inside the machine. But in two years of working on this computer, I have never found a single hardware defect with this system. And not one single tweak I have made to it has kept it from crashing. Even when I reformatted the hard drive and did a full reinstallation of Windows, which was the recommendation of Dell�s paid software support team, the PC quickly went back to more BSOD. If someone told me they reinstalled Windows on their system but it kept crashing, I would probably assume there was a hardware issue too. But again, I have searched and searched for evidence that the hardware is broken, but cannot find anything.
All of this makes me wonder; maybe the PC arrived with the problem. Perhaps the OS was initially installed with a bad copy of Windows? Maybe when used that same disc to reinstall the OS, I just put the same problem back into the computer. It has been suggested to me that I conduct a Repair Install of Windows to fix some issues I discovered. Recently I ran the �sfc/ scannow� command and received a message stating that there were corrupt sectors that could not be repaired. But I am afraid to try to fix it with the OEM CD. This is the same CD that failed to fix the issue when I did a full install. Is it possible that if I use this same disc again that I could be replacing the same corrupt system files all over again? I am curious to hear feedback from others. Have any of you had an experience like this one? Is it possible that the OEM CD I received is damaged?
I'm working on a Brand New Dell Inspiron 1525 with W7 OS. I was in the middle of catching it up on all the updates and they went in fine except it when it got to Service Pack 1, It will not install SP1. I receive the error code: 800B0100 I also went thru the steps of "Get help with this error" and it went thru "Windows Update troubleshooter" said the problem was "fixed", however still failed the next 4 tries, any suggestions? THX!!!
Installed Windows 7 Service Pack 1 yesterday. Today, Windows Live Mail is asking for my username and password for my Comcast mail account. The name & password provided are correct. When I OK, the box just keeps reappearing. When I cancel, error message states a wrong password was provided. I am using Firefox as my browser. When I try to open my Comcast mail from the Comcast site, it times out. I AM able to send emails from Live Mail...
I am trying to trouble shoot my boss' laptop. We have tried to set him up on Windows Live to use while he is at home and on the road. We have a server and it is setup/configured on his laptop correctly as it works EVERYWHERE else besides his home. I am guessing it is a Firewall or Router Setting issue. Since I don't go to his home, I am unable to trouble shoot it there - His family has an IPAD an ITOUUCH a personal computer and another laptop and they all send and receive mail fine. It is just my boss' laptop - Windows 7 - Home Edition - 64bit - Dell. Thinking maybe I need to change the port # in the settings on Microsoft Live. BTW - we do have him set up to use the Exchange by logging into our IP - but he just cannot seem to get the hang of doing that - even though i have everything shortcutted and instructions on the desktop...Also have had him just use Log Me In - and he doesn't like the small screen..
My problem is that if I connect the computer via DVI to a display it functions normally, but when I hook it up via HDMI to my Flat screen, it doesn't show the splash screen that gives you the option to enter bios. The screen just stays black until the windows welcome screen(win 7 64bit) comes up, then it acts totaly normal from that point. When I try to press the del key during the boot, I believe it is entering the bios, but the screen remains black so I can't see anything. I am guessing that the MB is not sending the signal to the Flat Screen until it loads windows, but can't find out anywhere that confirms that or what to do in order to resolve it.