Windows 7 Not Installing On Seagate Barracuda St3500418as
Dec 21, 2012
Problem with my acer m4 series computer. I recently installed backtrack linux and then fedora onto my seagate barracuda st3500418as hard drive. Now I deleted the partition containg grub and the extended partition containing fedora. My windows 7 installation was corrupted all along the way.I want to repair or freshly install windows but it says I need to load my own drivers. Whenever I boot into safe mode or start windows regularly, it flashes a blue screen and then reboots. By the way, I have the installation disk.
Had Windows XP installed on an old Seagate Barracuda 7200.7 120GB.Formatted the drive for a clean install from Windows 7 DVDNow I get this:
"Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu."
It is, and yes it can. And why is it even saying this when the installer can format and partition this drive till it turns blue.It gives me the option to "Load Driver" but there are no drivers for this HDD, it's all pre programmed in the motherboards.
My motheboard is an Asus P8H67, like this link: url...How you can see it have 2 SATA 6gb/s connectorsMy hard disck is a Seagate Barracuda Green 2T 6GB/s, like this link: url...The hard disk is connected in a Sata 3gb/s connector. Can i turn it on the 6GB/s connector?
I have replaced my ASUS P8 Z68-V/GEN3 with an Intel Desktop Board DZ77SL-50K and at the same time the primary hard drive has changed from a 1TB Seagate Barracuda to a 3TB Seagate Barracuda. The new system is working fine apart from that the 1TB Seagate Barracuda does not show up in Computer, Disk Management, MiniTools partition management, DiskWizard or anywhere else no matter which SATA cable, SATA port or computer is used. Consequently, I am unable to retrieve any files from the old HDD which is disastrous for my business. How to retrieve any number of files from the unrecognised HDD.
I went to Fry's and got a Seagate Barracuda 1TB 5900 RPM Hard Drive. I plugged it in as soon as I got home and it didn't show up in 7. I'll see if it wants to work with XP or Ubuntu, but I don't have high hopes.
Using Windows 7 Ultimate 64-bit. W/ASUS P7P55D Deluxe board. Very stable and non buggy. Computer was running great with multiple drives. I substituted one of my 1TB drives with a brand new Seagate 3 TB drive. With the new drive hooked up, the computer will not boot and gives a message that there is no hard drive detected, put media in and hit the key. (something to that effect).
If I enter the bios in the condition, it shows all the drives in their correct order and the boot sequence is the first hard drive, CD, etc. It has detected the new drive as drive #3. But it will not boot. But, if I disconnect the new drive (power and SATA connector), the compute will boot up fine. I have checked all the connectors ad they seem fine. Is there something about the sequence in which the SATA connectors have to be connected?
I own a Barracuda AC-1 as well as a HP-1 headset. I had this set up in Windows XP 32bit and got it working brilliantly?However, I recently purchased Windows 7 64bit Home Premium. I installed it this weekend but I have been having trouble setting up the soundcard and headphones to get the same result as I get in Windows XP. I have installed the Windows 7 64bit (Compatible) driver. This time, however, there is no Barracuda AC-1 Control Panel (green and black screen) which normally allows me to make specific changes to the audio. I have only been able to select and test the speakers within Windows 7 Playback Devices. I have played with Quadraphonic, 5.1 and 7.1 settings and still have been unable to achieve the same result as achieved in Windows XP. In fact, if I play some music it only plays through the front two channels as I tested turning down the front channel volume on the headphone volume controller and this turned off all sound.how I can achieve the same result as achived within XP where I have a AC-1 Control Panel (green and black screen) and achieve full sound through all channels.
I haven't been able to get the Vista 64 drivers to work for my Razer Barracuda AC-1 sound card. I didn't know about the driver signing conflict, and tried to install. When the OS kicked it out, I tried to find a way to disable driver signing. While I appear to have stopped the check, uninstalling and installing the drivers is still not working. I seem to have the drivers permanently flagged by Win 7 as unsigned.
Does anyone have any recommendations for trying to get my card working?
So every since I switched from window xp to window 7, my razer barracuda sound card driver does not detect 5.1 speakers. The option to change the DB for each speakers is not there anymore. Is this because the driver for window 7 is not out? Or is it window 7 in general and I need to change some settings. Please let me know what it is! :]
I have a new computer with windows 7 been used freeagent fine with old computer, but when I try to backup(restore) old files or sync it keeps telling my I need to reconfigure as I have vista?? is windows 7 really vista, I was able to move old quicken files but not itunes or outlook files?
Continuing from a previous discussion, I backed up this computer (HP Pavilion desktop 2.7 mhz 6 gig) to my external Seagate hard drive, using Windows 7 backup routine, (after re-formatting the Seagate). Everything has worked just fine.I did a second backup today, and when I went to look at the external drive, it appeared as if no changes had been made (same date as the 1st backup to the 3 files on the disk). So I opened up "Mike-PC" and aha, the next file had today's date. OK, that fine, and total disk space used equals total disk space used on the internal hard drive. So everything's cool, but I wish the backup routine would leave a "last modified" label up front.If I use this same external hard drive to back up my wife's brand new HP laptop, will it clobber my backup, or will it make a new file?
Recently purchased a Seagate GoFlex Home NAS drive and having troubles getting my Win7 laptop to see it on the network. Here is a basic rundown of what works and what doesn't:I can ping the IP address from the LaptopThe NAS drive appears in the network map but not in the Network heading in explorerI can access the NAS drive through the browserI have full access to the NAS drive(mapped drive etc) through my Vista desktop on the same networkI can access my Win7 Laptop from my Vista desktopThe desktop's name appears on the Win7 machine but I can't open it (Windows says "Windows cannot access \DESKTOP")I have setup network discovery, file and printer sharing etc in advanced sharing options.
I am running Windows 7 on my computer and have somehow used windows security to lock my seagate external drive. The computer can tell that the drive is there but I cannot access anything on the drive and also cannot write to it. I have tried talking to tech support from Seagate and they said that since I have used a third party program that I need to contact them. It is difficult to get a response from them. I am a novice when it comes to things like this.
I have plugged my old Seagate external hdd into my new Acer with Windows 7 64-bit Home Premium. I am trying to pull files on to the new computer. It says I don't have permission to access the folders. How do I go about getting that permission while it is plugged into the new computer?
I recently purchased a Seagate external drive. I created a backup of windows to the disk using the Memeo software provided by Seagate. I tried to restore a file and I keep getting error message "The files cannot be restored at this time / try again later". I thought maybe it was still backing up but it states the backup is complete. I went to the seagate/ memeo support site and its basically useless. Of course they dont have that error message referenced.
Should I delete this Memeo software completely and let windows run the back up instead? I'm really confused now. I've been reading a lot of people have problems creating a backups with windows7 too?
I've had a sudden loss of my hard drive space. I've deleted alot of stuff, like over 20GB, more then just a few times and it just disappeared in less then 2 days. I've read some topics here with the about same problem and tried what they sugested there: to use software like WinDirStat, TreeSize Free and SpaceSniffer. But they just won't show me my whole hard drive. The stop at 50% and show it as if they have scan the whole 100%.
Me and my fiance just finished putting together her first real gaming computer and we wanted to use a Patriot 64g SSD to put win 7 on and use a 1TB Seagate drive for all the rest of the storage. The installation of Win 7 onto the SSD went nice and smooth but when we get into windows it is not detecting the 1TB HD at all. Funny thing is that when I go in to the SSD properties, I can see the Seagate under the sharing options. The only info I have found is how to clone off an existing hard drive with Win 7 on it not how to do a fresh install on 2 new drives.
I tried installing 64bit Win 7 Ultimate on mirrored 3TB Seagate HDD using a Digitus RAID card and failed. After the failed attempt, I disconnected the HDD and plugged the primary HDD to an on-board SATA connector only to find its capacity reduced to 750 GB. Windows Preinstallation Environment shows the same size and running clean produced no effect.
Something odd I noticed after running diskpart is that no matter how many drive is connected to onboard SATA, it only shows the 750 GB and the PC name is MINWINPC.
I`m completely stuck with this and cannot figure any solution. Please anyone help me restore the original 3TB size.
I recently upgraded from Windows Vista Business to Windows 7 Professional. The problem I am having is that my Seagate Freeagent 1TB drive wont load in Windows 7. I have to keep going to Device Manager and Uninstalling the driver and then plugging it back in so it automatically installs itself and then when I shut down the computer I have to do the process again.
I thought things that worked with Windows Vista were supposed to work with Windows 7.
Any solutions or help on this problem would be appreciated. PS I have already tried installing newer drivers, I have the latest ones, and I know this is a software issue as I am able to access the drive as normal after re-installing it each time.
Recently my PC just randomly crashed and upon restart, would not barely get past POST screen and get stuck on "Detecting IDE Drives...". I isolated the problem to my Seagate main drive. I went into diskpart and tried list disk, but the drive would not even display there. Does this mean my drive is pretty much dead?
Seagate provides a FREE download of their Seagate DiscWizard It is Acronis True Image, but slightly tweaked for Seagate.I have used it many many times for XP, and it is fairly 'idiot proof'.I cannot say the same for Windows 7 Imaging.Creating the image is 'idiot proof'Restoring the image is a mental challenge for me.Say I had just one partition on a drive, and I create an image.When you try to restore an image, you have to choose from three checkboxes
- CMD 100 MB - OS (your real partition) - MBR
there should be one box that you could tick to restore my simple one partition drive, BUT THERE AIN'T So I have to decide which of the three checkboxes to tick I would like to tick the lot, BUT YOU CAN'T You can only tick one at a time.I do not know which one to do first.And if that was not enough of a problem, you have to decide whether to make it Active
(Do I make the CMD Active ?) (Do I make the OS Active ?) (Do I position the CMD Hard left) (Do I position the OS hard left)
And if that was not enough of a dilemma, You are given two ways to Restore the other two checkboxes
- You can do a mini reverse (Before allowing the Restore) to tick one more checkbox, OR
- You can Restore each checkbox one at a time.Either way, you still have to decide on making each Active, and 'hard lefting'.Needless to say, I got it wrong, and am about to delete all the partitions (CMD apparently being considered a partition) and try Restoring again.
i had to re set my pc to factory.when i plugged in my seagate ext hard drive, i cant view my documents anymore. it keeps saying i dont have permission to access the folder...i have tried renaming me as the administrator, but my head is a bit messed up with it now,, i'm not what you call a technical pc person
I recently purchased a usb 3.0 enclosure from silverstone model ts07b and a new 2 tb drive from seagate model ST2000DM001; the usb 3.0 card is from syba model SD-PEX20093. The problem I am having is that when I plug the enclosure into the usb 3.0 slot with the seagate hdd the computer does not recognize it, but when I plug in another 2tb drive from WD (caviar green wd20ears) the computer recognizes it. I know the seagate is not dead because when I plug the enclosure into a usb 2.0 slot the computer recognizes it. Now I need to know what I should replace, should I get a new enclosure or pci card?
I had a 2 TB, and 3TB Seagate Go HDs and decided they would be best used as internal drives, turns out they both crashed completely upon SATA connection in the motherboard, I first guessed probably due to the difference in boot record. Upon reformatting in NTFS, I have found that the drives run very sluggish, I have been debating on just buying a new USB drive and copying my files, then getting rid of these 2 HDs. This doesn't make sense to me as I used to think all HDs were the same, does anyone know any reason why these 2 external drives are killing my system performance after they were made into internal drives (also why would they completely crash before).
Quote: Seagate has confirmed plans to release a 3TB hard disk drive later this year. However, the 3TB drive will only be recognized by 64-bit operating systems, such as Windows 7, Vista and Linux. "Not only that, but you may not even be able to see 2.1TB of a 3TB drive when using Windows XP," wrote Thinq's Ben Hardwidge Read More: Seagate says 3TB drive requires 64-bit OS | TG Daily
In Windows 7 RTM I have had trouble with one of my two HDs, a Seagate 300 GB. During Windows 7 installation, installer "could not find drivers" when the Seagate was the first SATA drive. Once the Western Digital drive was set as the first drive, system installed ok.
After installation, the Seagate shows in the Disk Management as 300 GB, but if look at contents with Explorer, it has only 125 GB capacity. Can this be a Seagate firmware problem? (Windows 7 RC earlier had no problems with this drive when the system had Win7RC + Vista + XP.)
I must be missing a step somehow, and I'm not so tech savvy anyways, but.. I have an '08 dell xps 420, recently installed win7 ultimate x64, have 6GB ram, backed up oem internal to 2tb external, also did windows easy transfer copy to ext, now replacing oem hitachi 750mb internal w 2 1tb seagate barracuda hd's...booting from cd-rom drive works fine, but cannot seem to get raid0 config worked out nor load drivers for drives.
I just purchased a Seagate Go Flex 2TB external drive for backups. It comes with software called Replica(v.5). I have been reluctant to use it due to reports (seen post purchase) that it causes system crashes especially with right click and that it slows system performance terribly. I have a new win 7 pro 64 bit (OEM legal) DIY build system.
I've been having a lot of problems with torrenting lately. I tried to figure out why I kept getting BSOD's from simply installing the torrent applications on my computer. It all started when I needed a new hard drive. I bought a Seagate HDD at Best Buy back in October. After installing everything that I needed to on my computer, I started having problems. I would constantly get blue screens which I couldn't figure out for a long time.
I've got two laptops. The one I'm primarily using is a Samsung QX411 with Windows 7 64-bit and the other is an ASUS X53U with Windows 7 64-bit. Both not running torrents and ended up with constant BSOD's. I took the Samsung in to Best Buy and they told me I had 29 viruses, even with my virus protector giving me no warning of having a single virus on my computer. After downloading uTorrent, I apparently had this weird uTorrent toolbar, which, I believed, at the time, that what was driving the viruses. I've never had a single problem with torrents or uTorrent ever up until now.
I downloaded uTorrent off of their website. I even tried Bittorrent but that ended up with these apparent "viruses" as well. Somehow, this StartNow toolbar, known for vicious viruses, had been added to my computer without my knowledge and this other strange toolbar that gave me a weird homepage with virus ads below a Bing search bar in the center.
Evidently, the new Seagate HDD I bought for the Samsung did fail and I ended up having to get a new one replaced and installed. I lost everything on my computer. Now I'm using a the 2nd new HDD and it's already given me problems with BSODs. I wanted to see if I could transfer the uTorrent over from the ASUS since it's no longer having torrent or blue screen issues instead of downloading it from uTorrent's website and it still gave me another BSOD.
I took it back into Best Buy recently and they told me that I had 49 viruses this time completely out of no where since everything on my computer was completely brand new and they removed uTorrent off of my computer once again. I haven't had a single problem since they removed it but I just don't understand what I can do about the Blue Screening. I can't use these Blue Screen applications to recognize what's causing the problem since every time I get a BSOD, it says failed to create dump files.
