I have recently installed a new cpu cooler and tidied up my cables, I have replugged in my sata cable but now I have the no bootmgr problem, all was good before this and now I can't start windows 7.
View 3 RepliesI recently purchased a Lenovo Thinkpad Edge and loaded all my usual programs on it that I used on my previous computer. I'm not positive exactly when, but currently my computer will run very fast when plugged in. Then if I unplugg it to do some work in "the office" it will continue to run just as fast and smooth. However once I replug in my computer it will run very choppy and slow and it is basically impossible to use before I restart it. Once I restart it it will run perfectly again. [code]
View 2 Replies View RelatedWhen i first installed windows 7, everything was going great. until i restarted without the windows 7 disc in my drive... then it all went wrong.
I have three hard drives.
1) Windows Vista 32bit Ultimate
2) Windows 7 Ultimate RC 32bit (partitioned in half, primary and logical)
3) Storage of my junk
The second hard drive is 160gb, partitioned in half to make to 80GB's. They are all sata, along with my dvd drives.
When i turn my computer on with hard drive 1 set to boot first, it boots vista perfectly fine. (no option comes up to pick an operating system)
When i turn my computer on with hard drive 2 set to boot first, and i DONT have my windows 7 dvd in, it comes up with BOOTMGR IS MISSING...
When i turn my computer on with hard drive 2 set to boot first, and i DO have my windows 7 disc in, it works perfect.
Is there a way to not have to put the disc in to boot all the time?
And its also strange that i dont have an option to select which operating system to boot from... its either one or the other
I have tried unplugging seperate hard drives and nothing changes, and i have tried start up repair from the windows 7 disc - still nothing.
The second problem i have, is hard drive 3. it is recognised in vista, but whenever im using windows 7, it does not detect the drive. Any ideas why it appears in vista and not 7?
i tried unplugging and re-plugging when the computer is both on and off, and its ALWAYS detected in the bios, just not windows 7.
Basically I put a new hard drive into my laptop and tried to install windows 7. It keeps saying bootmgr is missing, press ctrl + alt + del to restart. The OEM windows 7 disk is inside my cd-rom drive and I went to the bios and put the cd/dvd as first, and the hdd as second, pressed f10 (save and exit.) and still no luck.
View 3 Replies View RelatedMy C drive is failing and I need to replace it. I have software to clone the C drive but Win 7 seems to be installed on 2 drives? There are 2 drives in this system. This system started with XP and I at some point upgraded to Vista. Then a year or so ago when Win 7 came out I upgraded again. It seems some how Win 7 has used the 2 drives in the system to install. When I disconnect the old drive that was there when I installed XP, on boot I get a message that it can't find win 7 and I need to insert the Win 7 install disk to repair the system.
First, how did it use 2 drives to install it's self (win 7) and is there any way to correct this so it's only on the C drive and I can clone it and replace it?
Second, the repair option. Will this wipe everything out? If I do the repair will everything be the same except it will boot with just the C drive and I can then clone it and replace it or will it wipe everything out?
booting through USB and it's quite hard to explain but at the moment what I need to know for succeeding with the installation is, is it ok to unplug the USB flash drive after the first restart during the installation? My friend just told me that after it is done expanding the files and reaches 100% and does it's first restart, I can unplug the USB and it will continue it's job as all the files are saved on the HDD now.
View 7 Replies View RelatedI have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
View 3 Replies View RelatedBootmgr missing error. Dell Inspiron 560. DVD drive won't read disk to reload. Downloaded disk to USB n it won't reload. Changed boot options thru f12 key to no avail. Also can't access command prompt or any recovery key.
View 9 Replies View RelatedI have 3 drives, C-OS internal, D-data internal, E-data external. "Bootmgr" appears on C and E, but not D. I thought this was some kind of error, deleted it off E, machine wouldn't boot. A quick fix with the Win 7 DVD, all was well again.Is there any reason the bootmgr file is on the external drive?
C = RAIDO - 4 SSDs
D = 64 GB Patriot SSD
E = WD 640 GB spinner - connected by eSATA cable to eSATA port on back panel.
So, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?
View 9 Replies View RelatedHave formatted this disc 2x and still get Bootmgr missing error, wont take a new install of an OS. Originally had windows 7, have key but no install disc for that, tried installing XP and could not get to bios?
1. Is it a bad hard drive?
2. Is it in the motherboard?
Is there action I can do? Pc will only allow for ctr. alt del which gets you back to square one again?
I have a HP Mini netbook which is just out of warranty. When I start computer i get a black screen with the message bootmgr missing.I have tried recovering system using start up recovery, etc, etc but still end up at same screen.I can get into the command prompt screen but have no idea what to do next.. have found on the web is for laptops/pcs with a disc drive, mine doesnt have one.I am not an expert on computers so
View 1 Replies View RelatedI have a HP Touchsmart IQ500. Turning my computer PC on today, all I got was a blue HP invent screen with setup, boot menu, system recovery, and system diagnosis, and I could not get past it. I entered the BIOS and figured out that the hard drive was listed as "not installed." Pretty sure that is the main problem.I tried a system restore (with the Windows 7 install disc), but I guess the computer couldn't read the hard drive enough to enter safe mode (I tried restarting and F8ing several times). I put in an external hard drive, and the BIOS read it; however, windows does not allow you to partition an OS on a hard drive.
View 2 Replies View RelatedI have an internal hard disk not in use ,and I would like to make it as external disk !I looked on the net and I found I should have the " encelsure " butt I think I wont find it here in my city .So is there another way ? like usb -esata cable
View 3 Replies View RelatedMe and my brother built me a new computer from scratch (he did the building - i did the watching). I purchased an internal hard drive from Overclockers UK. It's a Samsung 1TB drive. I also have a 64 Solid-state drive in there as my primary hard drive that Windows was installed on and a couple of programs are installed on. My storage disk (the 1TB disk) is for all my music/films etc. Whenever I drag and drop a file into the Samsung hard-drive - it copies it rather than moves it instantly.When I had a laptop, I had 3 external hard drives and this is the way it copied files onto them.how I can get the internal drive to stop acting like an external drive?
View 6 Replies View RelatedI have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
View 4 Replies View RelatedI have a USB Webcam 6.1.7601.17514 from Microsoft installed on a Fujitsu Laptop (Windows 7 ) and I want to copy and install it on another Fujitsu laptop (Windows 7).The other laptop the camera is not working and there is no webcam driver installed.
View 1 Replies View RelatedI have Vista installed on my Hard Drive, 250 GB.
But i recently purchased a 2nd Hard Drive, 500 GB, and i want to install Windows 7 on it.
Is that possible, to have both separately?
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
View 5 Replies View Relatedi have unplugged my computer, instead of logging off. can this cause any system file damage and the blue screen?
View 3 Replies View RelatedI loaded Windows 7 on my laptop and everything works just perfect. However, when I unplug from power the screen saturates or goes to a white screen with only the darkest colors showing up. Impossible to do anything while unplugged. But as soon as I plug back into power, about
3-5 seconds later the resolution comes back. Here are a couple pics of the same screen plugged/unplugged.
Any thoughts?
I installed Windows 7 (x86) today, but have found some trouble with getting a Internet Connection.
I'm using a dc-202 router. Windows doesn't detect any connections, and when going to network connections it says: Local area connections ; network cable unplugged (tho the cable IS plugged in, and my driver is up to date). My Ethernet card is a VIA Rhine II compatible fast Ethernet adapter.
I already tried to reinstall windows and to skip the router, and just connect directly to the Modem. Even then, I get an error stating: unidentified network. So when i go trough the router, i can't see any connections, when i go directly trough the modem i do get a network, although i cannot connect to the Internet). I can't go on the Internet either way.
I hope this is enough information, otherwise i have some typing to do (cant post on my own computer, or use LAN)
So my grandpa got a new laptop for his birthday a while ago... Strong laptop, nice hardware. Can't remember the name or model though...Anyway, so he runs Windows 7, and he told me that every time when he pluggs out the charging cable, the computer shuts down. But when the cable is plugged the computer runs just okay and the battery is full.
View 7 Replies View Related"Windows has encountered a problem communicating with a device connected to your pc.This error can be caused by unplagging a removable storage device...,or by faulty hardware such as a hard drive or CD-ROM.Make sure any removable storage is properly connected and then restart your pc.
View 1 Replies View RelatedI recently installed Windows 7 ultimate , earlier i had xp. Now i am able to use wireless but not the LAN. I have checked in change adapter setting and its keeps saying network cable unplugged.Windows 7 , 32bit.Intel r82562gt 10/100.Latest drivers installed.Cable is perfect.Laptop is HP550.procesor Intel core2duo t5270.In device manager i can see under network adapters two options and these are intel r825662gt 10/100 network connection and intel r wireless wifi link 4965ag.Please suggest me some way out as at my home i don't have wireless. I tries to include all the info which i thought would be necessary still if any reg do let me know.
View 3 Replies View Relatedi've decided to try out windows 7 64bit. after fresh clean install i had an issue with drivers for my integrated network card, which i installed from CD i received when i've bought MB, which is ASUS P5B Deluxe with following network devices :
Marvell 88E8056 PCIe1x 1 Gbit/s LAN
Marvell 88E8001 PCI1x 1 Gbit/s LAN.
now i have 2 network devices displayed in device manager which appear to be working properly :
marvell yukon 88e8001/8003/8010 pci gigabit ethernet controller
marvell yukon 88e8056 pci-e ethnernet controller
and then 3 "other devices" left with yellow exclamation mark :
ethernet controller
rtl8187_wireless (i've disabled this one since i don't need wireless)
unknow device
i also have tried to install newest drivers from marvell homepage, but nothing has changed. i've also tried to setup speed on both network devices from auto to 100mb full and half duplex, but i'm still getting cable unplugged message.
i didn't play with router so far. my network was working with XP32bit without problems.
i have a feeling, this problem will disappear with 32bit release, but i'd rather try the 64bit one. is there anything i can possibly do to get rid off this problem?
LE: i've also tried to go directly with my internet cable without router, but the result is the same.
I just downloaded new drivers for my Realtek Audio and now every 20 minutes or so I'm getting a message pop up saying "You just unplugged a device from the audio jack." and for about 2 seconds audio won't work, then it will work fine. This has only happened after I downloaded the new drivers. I've checked the physical speaker connection and it's properly in there.I don't know how to get the exact name for my sound card so if that's needed please tell me how.I suspect that it might be because of some other out of date driver, if it is so I would be very grateful if you could give me links to where I could download drivers because besides this update and graphics cards updates I have no idea how to update any other drivers.
View 5 Replies View RelatedI have an application that establishes a socket connection w/ another application on a different machine. When this connection is disrupted (e.g., pull out network cable), I recognize this condition and take some action.
In a Windows XP 32-bit environment, this happens quickly ... in seconds.
In a Windows 7 64-bit environment, this happens slowly ... in about 5 minutes.
If I run netstat in the Windows 7 environment, the TCP connection shows established for about 5 minutes after the network cable has been unplugged. (In WXP, it changes in seconds.) I've searched the forum and have heard a few people refer to 5 minutes as being a "default" timeout value. I've also looked at the TCP spec, etc. to learn a bit more, understand it better, etc. in an attempt to find something I can configure to reduce the 5 minutes to seconds but I've not run into anything yet.
OS: Running Windows 7 Home Premium 64 bit on Laptop and PC (custom build).
Router: ASUS RT-N56U
Switch: D Link DES 1008e
Network Adapter PC: Realtek PCIe GBE Family Controller
Network Adapter Laptop: Realtek PCIe FE Family Controller
When either is plugged directly into the router, no ethernet cable is detected. If you run either the PC or laptop through the switch first, it works just fine. I have uninstalled and re-installed network drivers, I've uninstalled and deleted the adapters and software and started from scratch. I've checked all of the setting 3 times over.
The audio from my computer completely went dead when I turned it on. The speaker icon shows the symbol with the 'X' on it and after clicking it and going through the troubleshooter it can detect no problem. I tried updating the drivers through the HP website, and uninstall/reinstalled them but it still doesn't work. I even tried rolling back the computer to a restore point but that didn't work either.
The speakers are built into my monitor and is connected through a normal audio jack (not HDMI). I normally use my headphones through a jack built into the front of the tower.My computer is a hp Pavillion Elite m9400f, Windows 7 Ultimate 64X (It also has a ATI HD Radeon 5770 graphics card; but I'm not sure if it's relevant to what might be causing this problem).
I have a Gateway model MD2614U laptop os Windows 7 home 32bit. When I unplug the headphones to use the internal speakers sometimes the laptop will switch over and sometimes it won't. When it won't switch over. I open the volumes control window and I can see the green bar going up and down with the audio source but there is no sound coming out. I have to end up closing down the program that is producing the sound then the switch over will complete and I restart the program. I also have the same problem when I plug the headphones back in, again no sound from the headphones even though I see the green bar moving. Also some programs that send and receive audio over the internet will lock up when I unplug or plug in ether the headphones and or the microphone.
View 1 Replies View Related