Memory Not Running At Full Speed?
Jun 20, 2011It is running at 1300MHz constantly and it is suppose to run at 1600MHz, any reason why? Specs at bottom.
View 5 RepliesIt is running at 1300MHz constantly and it is suppose to run at 1600MHz, any reason why? Specs at bottom.
View 5 Replies'm a 3D artist, and I'm currently rendering out a whole load of frames. I'm using a reasonable, Sony Vaio laptop for the task, which has an Intel i7-720QM, however I'd like to know what CPU speed it's currently operating at.I know that it says it runs at 1.6Ghz as standard but then can ramp up to 2.8Ghz, I just wondered if it truly was going at that speed whilst it's rendering.
View 9 Replies View RelatedYesterday I installed RC1 of Windows 7 on my HP 6910p. After install I immediately noticed that the notebook makes much more fan noise then under Windows XP.
The fan seems to be running constantly and whenever I seem to do something a bit graphical it goes at full speed.
Are there any other (HP 6910p) users that have the same experience?
Is there something I can do / tweak to make my notebook quite again.
I have already disabled the superfetch however this only reduces the HDD activity.
I've recently bought a new computer which I had quite some trouble with. First of all the games that keep crashing (think it's a windows 7 issue so I'm just going to wait for the MS solution). Secondly I have (and this is the issue) my network that isn't able to run at maximum speed.
At the moment my Internet only works when I put network speed to 10mbps Half Duplex instead of 100mpbs Full Duplex. This means I only have a max speed on my network of 1mb per second and the same applies for the Internet. This computer is linked to a network of 3 other computers (who don't have a single problem) and is directly attached to a switch and then to a modem.
We tried many things to get it to work again, there was only one thing that actually worked. The thing that worked was attaching my computer directly to the modem. The problem is however that that means that all the other people don't have Internet.
My question is, is it the switch that causes this problems (it's updated with the latest firmware and was the newest version 1.5 years ago)? Or is it my computer that causes it for some reason (windows 7)?
I've updated every single driver, windows, updated bios etc. etc. I run windows 7 ultimate 64bits. ps. If you need more information, I'll be happy to give it to you. (thought I'd keep it as short as possible for now)
Hey guys. I got 10MB internet speed. So Im suppose to download on a average speed of 1.2MBPS.
View 9 Replies View RelatedI cant play the game in full screen it shows only in windowed mode. I cant put mouse cursor as well in window. I tried changing the resolution of the game but it doesn't change if I set it to low resolution, I cant see anything but can hear the sound.
View 1 Replies View RelatedI have 135Mbps link speed support ADSL WI-FI router. I have enabled 802.11b+g+n wireless mode and use 20+40 MHz on my router. I use "WAP-PSK" authentication. In addition to that, have a 2.4 & 5 GHz frequency support router and client device.
But my network connection display (WLAN) I have a 54Mbps link speed, why is that? How do I use 135Mbps or at least 100Mbps link speed? Is it a some configuration issue? My Ethernet connection show full speed (100Mbps). (I'm not talking about my internet connection speed).
Adapter 1: Intel Built-in Lan
Adapter 2: Pci Card
I used to access shared internet from a router, now the router has no internet we only use it for local home sharing. I added the secondary adapter to connect to the DSL-modem directly.so now when I disable the 1st adapter my internet works fine. when they're both enabled internet doesn't work at full speed or sometimes not at all.
I have a program that measures bandwidth and its reporting that I am downloading at full speed (1.2 mb/s ) all the time, and I think its accurate as my internet feels really slow. I double checked I wasn't downloading anything, and that all of the updates were on idle, but there is still traffic. What should I do? Also, I noticed a ridiculous drop from 250 GB to 217 GB of free space. The free space drop is gone, its showing 250 GB but the bandwidth is still a problem
View 1 Replies View RelatedSo I built a new computer yesterday and when I ran a speed test today I was only getting 9.5mbps when I usually get over 30mbps. It has something to do with this computer since my other computer is getting 30mbps. And yes this computer is connected directly through and ethernet cable.
View 2 Replies View RelatedWhen I connect my external hdd, it tells me that this device could work faster if I connect it to a Hi-Speed USB port. When I try to copy any files, transfer starts at about 70mb/s and stops after a few seconds, time left is calculating and when it starts again the speed is about 1.5mb/s. Sometimes pc doesn't find the hdd at all. I've installed the latest chipset drivers but nothing new happened.
View 2 Replies View RelatedI decided to open a thread to show what people are getting with there current memory settings, what improvements are shown with various timing tweaks, speed settings ect.
to access this you MUST have UAC turned off, OR choose 'Run as administrator'. open the command prompt window first, either by opening 'Run' from the start menu and typing 'cmd' --this will only work if UAC is deactivated--, or go to accessories in your start menu locate 'Command Prompt' right click, select 'Run as administrator'.
once opened simply type:
winsat mem
Note: it will not matter what the command path is set to.
i am currently facing issues with my DDR3 and being stuck at around 8500mb/s any suggestions why feel free. Dual channel and tri channel play a huge factor in this benchmark, so keep that in mind before comparing with others
so here is my winsat score:
with the current timings:
post em up and let other people know what basic timings and MHz your set at (DDR2 950MHz 4/4/4/12 ect) and channel configuration (dual/tri channel) your using.
thanks to smarteyeball for pointing out the admin trick with cmd.exe!
My desktop appears to be running on speed!I switched it on, and that startup screen with the four coloured windows logo, is flashing like mad. The next screen I get is the password screen. On here, the cursor is spinning like mad. When I try to enter the password, pressing the first letter fills the input box with characters. I don't know whether this is the character I have just entered, although I guess it is. If I try to delete the characters, pressing backspace deletes all characters in the input box. Pressing the first character goes through it all agaiin.I now have a desktop that I can't get into because of this. Nothing new has been added...software or hardware. Everything has functioned as normal prior to this.
View 3 Replies View Relatedi found this website,wonder if this works.
How to Speed Up Firefox by Running It In RAM - wikiHow, the free how-to guide
How can I find out what speed my cpu is working at?
View 2 Replies View RelatedBought i3 3220 (ivybridge), 2x4gb ram, 120GB SSD, CM Elite case & psuSo installed everything powered up got 4 beeps shutdownReset mobo as had been used before got 3 beepsI tried unplugging everything but cpu/fan/ramTried each ram stick in each slot etc checked cpu seated properlyTried everything i could think off got 3 beeps alwaysFinally i figured mobo might need bios update to run ivybridge chip (which was already supposed to have been done in old system) so i ditched the Z68 and ordered a gigabyte Z77-DS3H, so now all components are brand spankersAssembled everything 3 short beeps, pause, 3 short beeps shutdownSame as before unplugged everything same beep comboOnly mobo cpu/cooler/ram same beep comboWent to my office robbed some ddr3 out of my i7 system swapped it and still got 3/pause/3 beeps each stick in each slot and still the sameAnd i have noticed on power up cpu fan goes full speed for a few seconds then when beeps start it runs slowly dont know if this is relevantNow im stuckthe only components i havent swapped out is the cpu & psu, but is it possible the cpu is faulty, is this a common thing ???
View 9 Replies View RelatedI have a MSI GX640. it's default memory is the 2x2GB DDR3-1333 (Max 2x4GB) DDR3-1333 @ 9-9-9-24 Timings Recently I decided to do upgrade my memory from the total of 4 gbs to 8gb the type of memory i'm using is this Then I started getting rampant BSOD. I wasn't sure what to do, so I did so did some research. I was told that the memory clock speed or something could be off. I used speccy to identify what I had, it says this.
RAM
Memory slots
Total memory slots 2
Used memory slots 2
Free memory slots 0
[code]....
My laptop taking long time to boot once it is first turned on - If adding memory with improve the speed.
View 1 Replies View RelatedI decided to upgrade my pc by adding a new kingston 2G DDR3 1033 kit .. I Bought it and placed it in the same slot color with the old one (kingston 2g DDR3 1033) .. when i turned on the pc it just gave a black screen without any beeps .. i removed the new one, it worked well .. i changed the clock freq. from the bios from AUTO To 667 and 553 and aslo they didnt work .. BUT when i changed the freq. to 400 .. the new kit worked well with the old one
This is my pc spes. without the new ram installed With the 2 rams installed it Reads 400 MHZ What should i do ?! Is the New kit is bad ?
Note the old one Model is KVR1333D3N9/2G and the new one is KVR1333D3S8N9/2G
To start, I have Windows 7, on Sony Vaio laptop. I have been working on the issues with the malware removal team, but now machine looks clean, I am still having issues. When starting the computer and going to the task manager, I can watch explorer.exe start at about 18K memory usage and then grow constantly until it is running with almost all of the computer's physical memory after about seven min. I cannot get the context menu to show up after a few min by right clicking on anything. I had been experiencing "freezing" while playing Eden Eternal (an online role playing game) before that, which made me consider malware and seek help here at BleepingComputer. The freezing has ended, last time I played on that machine at least, but now there seems to be some issue with the explorer.exe taking all of the memory. I haven't been using the machine since I don't trust that there's not something running in the background that shouldn't be. In resource monitor there were "connections" that had "-" for both the name and the PID, but I don't know if that was the malware of if that's normal somehow? Issue with explorer.exe seems to be limited to only one user account, and not the other one. That is to say that if I log on one of the other accounts explorer.exe behaves normally, as far as memory usage.
View 12 Replies View Relatedi using mada internet connection now speed is very slow?
View 1 Replies View RelatedI brought a new CPU yesterday Motherboard : GA-880GM-USB3 (gigabyte)CPU : AMD FX 8120Memory : 4+4 DDR3 RAM 1333MHzBIOS VERSION : GA-880GM-USB3 FE OS installed : I have both windows 7 x86 and x64 installed on the machine. But my problem is that when ever i run windows either of them, I can only see 6gb of ram and of which only 3.5 is useable in x64 and 2.8gb useable in x86. BUT when i installed CPUID's CPU-Z I can see that the whole 8gb of Ram is working, i.e., hardware is fine, but how do i get to see the whole ram and utilize it fully
View 9 Replies View RelatedNFS is no playing in full screen. There is black space for about 1 inch on both sides of the screen vertically.
View 4 Replies View RelatedSo I recently bought GTA IV, the minimum graphic memory to run it is around 256MB so as I have 353 MB I decided to give it a try. The entire installation process went on smoothly and when I run the game everything works ok but after the loading process when the cutscene starts the graphics become very horrible. When I checked out the graphics tab it showed me that I was using 256/60 MB. As far as I know my graphic memory is 383 and another surprising fact is that when you over-ride the memory in this game it actually turns the color of the font red 256/60 MB text. When normal green in color) but the color was green. I even tried increasing the setting but it didn't allow me to increase it.
Here are my graphic specification:
Name: Mobile Intel(R) 965 Express Chipset Family
Manufacturer: Intel Corporation
DAC Type: Internal
Approx Total Memory: 353 MB
Current Display Mode: 1280x800 (32bit) (60Hz)
Monitor: Generic PnP Monitor
i am using dell studio 1737 and windows 7 x64.with latest driver obtained from dell site.cuz i could not find it on intel site.it has intel GMA 4500MHD.
anyhow my problem is,i am using doom3 and on MS compatibility site it says,that it is compatible with windows7 but it does not run in full screen,it always runs in short mode,from vertical angle it runs in full length but in horizantal,it leaves border on both left and right side,almost an inch.
i searched for it lots and found that i must check my intel vga main settings panel to allow it use full screen which i have attached with,the screenshot.it is using full screen mode,but it is not using full screen,
i installed vista on my drive D.and in it,it used full screen resolution.
I have (had) a windows seven home pro laptop, the memory was almost full, it kept freezing, and now it wont load at all. It just comes up with a blank screen. How do I get I into Dos and tell it to load windows? Also, will this work? If not, what else can I do?
View 1 Replies View RelatedI run win 7 sp1 on dell inspiron 1520.Wenn i open some programs or games, there are two black parts at the right and the left of the screen.I have also uptated all my drivers using widows update and also drivers genius professional.wenn i was running xp, there wasn t this problem.here are the screen shots
View 6 Replies View Relatedi am running windows7 ultimate x64 but my problem is,that when i run doom3,it does not come in full screen,it has 1inch border left from both left side and right side...it does never come on full screen.i even changed option to use high resolution,full screen but it didn't solve problem,then somewhere on net i read,hit alt+enter,i did this too.but still problem didn't solve.
i am using dell studio laptop 1737,and it has intel GMA 4500MHD vga,i hav downloaded the driver which is latest for it even for windows 7 (from dell...i couldn't find it on intel)
lately i installed NFS most wanted,then NFS carbon..both had same problem as doom3.they are not using full screen.but in my intel vga properties,it says that it is using full screen.i have attached the image of my vga panel.
Wenn i open some programs or games, there are two black parts at the right and the left of the screen.I have also uptated all my drivers using widows update and also drivers genius professional.
View 5 Replies View RelatedI m running Windows 7 ultimate x64 on 6 pcs. All connected with cat6 cable to Gigabit Ethernet 8 port switch. Most of the PC have Realtek 8111F, 1 x Gigabit LAN Controller on board (1 or 2 have intel pro giga)
Now question is what settings should i make so that my all pcs can use full available bandwidth/data speed ?
(lan card properties have many settings in advanced tab such as ..packet size,link speed,buffer etc.)
It wont run in full screen always in middle. I tried messing with game options but it doesn't work for all games, I really need this fixed. I am using Radeon HD 5470. Windows 7 intel core i5 4gb ddr3 rams.
View 14 Replies View Related