Power Up Cpu Fan Goes Full Speed For A Few Seconds Then When Beeps Start It Runs Slowly?
Dec 1, 2012
Bought i3 3220 (ivybridge), 2x4gb ram, 120GB SSD, CM Elite case & psuSo installed everything powered up got 4 beeps shutdownReset mobo as had been used before got 3 beepsI tried unplugging everything but cpu/fan/ramTried each ram stick in each slot etc checked cpu seated properlyTried everything i could think off got 3 beeps alwaysFinally i figured mobo might need bios update to run ivybridge chip (which was already supposed to have been done in old system) so i ditched the Z68 and ordered a gigabyte Z77-DS3H, so now all components are brand spankersAssembled everything 3 short beeps, pause, 3 short beeps shutdownSame as before unplugged everything same beep comboOnly mobo cpu/cooler/ram same beep comboWent to my office robbed some ddr3 out of my i7 system swapped it and still got 3/pause/3 beeps each stick in each slot and still the sameAnd i have noticed on power up cpu fan goes full speed for a few seconds then when beeps start it runs slowly dont know if this is relevantNow im stuckthe only components i havent swapped out is the cpu & psu, but is it possible the cpu is faulty, is this a common thing ???
View 9 Replies
ADVERTISEMENT
Feb 2, 2013
I bought a new CPU and Motherboard today and put them together. I'm assuming I plugged the wires properly. So far no beeps when i start the computer but the fans are working and the LED lights light up. The monitor says "power saving" everytime I start it up. I have windows 7 32 bit installed on my hard drive and was planning to format it into windows 7 64 bit but I can't when my computer won't even start.
View 34 Replies
View Related
Jun 27, 2009
I have problem with Windows 7 on PC computer. IT runs slowly even i turn on clasic view and turned off all effects..
WIndows installed on Sata HDD 40GB, in system there is more two HDD with 160GB and 250GB
IT runs more slowly than Windows XP before...
I thinks it could be few possibilities:
1. Previous widows xp were installed on drive D (in the same sata hdd) and when installed windows 7 on C (in the same hdd) it shows me (when boots) one more selection to choose one more OS, but when I select it nothing happens just black window and I need to reset pc and choose windows 7 to boot. Maybe this issue can be fault?
2. My Sata HDD is very old. Maybe there is problem?
3. Maybe there is old RAM's and old CPU with MB ?
Windows 7 is officiall beta release from microsoft...
In example on my HP laptop with Centrino and 1GB RAM runs perfectly with pre-beta release installed earlier. Runs default without any modifications like turning effects or smth.
View 9 Replies
View Related
Jun 1, 2012
My system is a home built, Core I7, 8GB RAM, Radeon 560 TI with 2GB VRAM. Recently upgraded from 4GB RAM.
I was having this same issue with 4GB of RAM. After the computer has been on a bit (hour or two) the memory usage will approach 90% and upwards and things will start to run slowly. I close all active programs, kill all non-essential background programs (dropbox, steam, printer software etc). I look in my processes and no way does it all add up to nearly 8GB of memory.
So my question is, how do I get my computer to run faster? I know WIN 7 uses memory differently than XP did, and I don't care if it wants to use all the RAM, as long as it will run quickly. The problem is, it runs slowly.
I have WIN 7 x64 ultimate, I have ESET security suite and show no viruses. Problem goes away after I reboot, but returns over time.
View 6 Replies
View Related
Oct 31, 2011
I was forced to shut down my computer due to it having frozen up, whilst playing the Battlefield 3 single player. The computer crashed, and after about 5 minutes of rapidly pressing ctrl+alt+delete, and alt+tab, I decided the best way forwards was to force shut it down, by holding the shut down button. After restarting my computer, I noticed it took slightly longer to boot up. Hmm, nothing special. Then, I entered my login credentials, and after a 2-3 minute wait at the 'Welcome' screen, I was presented with a black screen, nothing more. After about 5 minutes, my cursor popped up. Oh, at least I have that. I pressed ctrl+alt+delete again, however after waiting 5 minutes for the screen to pop up, task manager simply would not open. I came back around 30 mins later, and the taskbar and my wallpaper had popped up. However, I pressed the start button to see if it would come up with the menu. Nothing. Cursor stops moving, bam. Another crash. Another forced restart.
This repeats once again, so I decide to head on into safe mode and try to go back to a restore point. Even safe mode is somewhat laggy, however it is not un-usable. After system restore is complete, nothing has changed. I still have to wait around 30 mins for the taskbar to pop up. I then tried using the repair tool you get to try if the computer doesn't start up properly. Doesn't work. My third option is to try out chkdsk, and that is happening as we speak. It has currently been going on for about 14 hrs, and found many corrupt files aparently in stage 4, however many of these files don't appear to be major. Its currently at 16% done, 205675 out of 371465 files processed.System specs wise, I have an Intel i5 460m processor @ 2.3ghz, 4GB RAM, 64bit operating system, and an ATI Mobility Radeon 5650, which I have overclocked to 650mhz core clock speeds, 950 memory clocks, from 450 - 790.
View 7 Replies
View Related
Feb 22, 2012
My motherboard is an Asus M3A78-EM and I have been using the system with the built in lan rated at 10/100/1000 mbps. The socket seems to be going bad so I tried replacing it with another internal card. They only had two to choose from at Office Depot were rated at 10/100/ mbps. and the other which was called D-Link DGE 530T which had the same specs as the motherboard so I got it. I've tried more than one cable and it works but is much slower did I buy the wrong thing to be running straight from a Wild Blue modem or, are there some settings that can be changed to speed it up I just run the one computer. D-Link DGE-530T Gigabit Desktop Adapter 10/ 100/ 1000Mbps PCI 1 x RJ45
View 3 Replies
View Related
Feb 6, 2012
I'm using a decent Lenovo B560 laptop, and when playing games or running programs linked to the hard drive disk, it freezes intermittently.
Not sure what's causing it, but the whirring of the disk drive can be heard for about 3 seconds, at which point it slows down, and then the game freezes until the hard drive starts whirring again. It doesn't seem to be able to keep itself running in order to keep playback fluid; it just keeps spinning long enough to power 3-4 seconds of playback.
System is 7 64 bit, with Intel Core i5 CPU M480 @
2.67GHz
3GB RAM
View 1 Replies
View Related
Apr 11, 2009
i have aproblem in windows 7 and i dont know how to fix it when i install a clean copy of windows 7 i notice that when i open windows in full screen its open slowly (cutting motion ) (creeper ) ?
View 9 Replies
View Related
Dec 26, 2012
My PC beeps 6 times when I try to turn it on, no error messages come up on the screen, the moniter and computer just go striaght on to stand by and the beeping continues.
View 6 Replies
View Related
Nov 2, 2012
My computer beeps twice during start up then option comes of pressing F1 to continue, F2 to enter menu and F12 to enter Boot menu. I have DELL XPS 15 laptop, and I am using my lappy from last one year. Is there a problem with my hardware?
View 8 Replies
View Related
Nov 2, 2012
my dell inspiron n4010 laptop fell in water and now it unable to start and beeps continously..
View 3 Replies
View Related
May 16, 2011
I am having a major problem with my laptop (Dell inspiron 1520). The laptop starts up, whe the dell logo disappears I get some very quick beeps (there must be about 8 beeps in total). I then get a boot manager screen which shows windows 7 at the top, and windows memory diagnostic in the tools section at the bottom. When I press enter it goes to the password screen and then after entering the password it seems to boot up as normal. I can probably get 2 - 3 minutes use out of my laptop before everything freezes. From this point I cannot do anything and have to tur the computer off by the switch.This is all it does in a constant loop.I have tried everything I can think of but still the same issue.
A couple of weeks ago my daughter spilt a little water on the keyboard. I mopped it up but next time I booted it up again the beeping noises started on start up. I removed the memory stick from under the keybpard and noticed there was signs of water damage. I removed the memory stick and the beeps on start up continued every time I booted the laptop up. But everything worked. Last Friday I was browsing the internet and that is when everything frozeI have tried to restore to an earlier date but it won't let me complete the restore. I have run the various disk repairs that are offered when pressing F8 at the dell logo screen but to no avail (it doesn't seem to find any issues). I really just want to get my files/photos off and then try and reinstall windows but as explained my computer won't stay on long enough for me to be able to do anythingThe computer will stay on in safe mode, however, it will not load in safe mode with networking. Could it be something to do with wifi? Reason I say this is I have been reading various threads and this has been suggested as a possible issue for one person's similar problem.
View 9 Replies
View Related
Feb 23, 2012
My computer decided to shut down on me in the middle of playing a game a couple of weeks ago. Hardware shut down - no warning, nothing. This is always worrisome, but it was even worse because when I went to turn it back on, it failed to post, stayed on for a couple seconds, then shut itself down. It repeated this cycle many times until I simply turned the power off on the PSU. I turned the power back on and it continued this cycle. Finally I just turned the power on the PSU off and left for the day. When I returned, I was able to boot the machine normally.About a week after that, I was once again playing EVE and the thing shut down on me and did the whole power cycle thing again. Remembering the fix from before, I turned the PSU off and left for the day. However, when I got back home, the problem persisted.
Currently, I am unable to get the computer to post on a regular basis with anything more than a single stick of ram (though it doesn't matter which stick and even then it's about a 25% chance). This includes removal of GPU, PCI cards, and HDD. Sometimes it WILL POST, but the Hard Drives are not detected, then then machine shuts down after about 30 seconds or so and returns to the power cycle mode.I cannot boot from my hard drive in my buddy's computer, but it is a much older AMD based system that originally had a 230w psu. I can however access it as a slave disk.I just replaced the PSU less than a year ago, and the graphics card about 18 months ago (an upgrade from an x1950pro, which blew the 550w PSU I had at the time).is the CPU temp sensor freaking out and shutting the machine down? Did the power supply go kaplooey (or about to)? Is my southbridge bad and causing all of the above (this is my #1 guess, as HDD's and PCI cards all cause major fail)?
View 5 Replies
View Related
May 20, 2012
is this just internet explorer starting as soon as i turn on the computer? If so, i need to delay it til i decide to go to the internet.How? i went to windows defender and i can't get it figured out. i don't see the option.Also i am getting error 101 boot performance monitoring. Is this related?also, i just checked in the event viewer, and i have 4 critical error 351- stand by performance monitoring. not sure if its related. I just want some direction on how to get these errors to stop popping up and have my computer running properly and to its fullest capacity
View 3 Replies
View Related
Sep 27, 2011
'm a 3D artist, and I'm currently rendering out a whole load of frames. I'm using a reasonable, Sony Vaio laptop for the task, which has an Intel i7-720QM, however I'd like to know what CPU speed it's currently operating at.I know that it says it runs at 1.6Ghz as standard but then can ramp up to 2.8Ghz, I just wondered if it truly was going at that speed whilst it's rendering.
View 9 Replies
View Related
Feb 13, 2010
I've recently bought a new computer which I had quite some trouble with. First of all the games that keep crashing (think it's a windows 7 issue so I'm just going to wait for the MS solution). Secondly I have (and this is the issue) my network that isn't able to run at maximum speed.
At the moment my Internet only works when I put network speed to 10mbps Half Duplex instead of 100mpbs Full Duplex. This means I only have a max speed on my network of 1mb per second and the same applies for the Internet. This computer is linked to a network of 3 other computers (who don't have a single problem) and is directly attached to a switch and then to a modem.
We tried many things to get it to work again, there was only one thing that actually worked. The thing that worked was attaching my computer directly to the modem. The problem is however that that means that all the other people don't have Internet.
My question is, is it the switch that causes this problems (it's updated with the latest firmware and was the newest version 1.5 years ago)? Or is it my computer that causes it for some reason (windows 7)?
I've updated every single driver, windows, updated bios etc. etc. I run windows 7 ultimate 64bits. ps. If you need more information, I'll be happy to give it to you. (thought I'd keep it as short as possible for now)
View 7 Replies
View Related
Jun 20, 2011
It is running at 1300MHz constantly and it is suppose to run at 1600MHz, any reason why? Specs at bottom.
View 5 Replies
View Related
Jan 31, 2011
Hey guys. I got 10MB internet speed. So Im suppose to download on a average speed of 1.2MBPS.
View 9 Replies
View Related
May 27, 2012
I cant play the game in full screen it shows only in windowed mode. I cant put mouse cursor as well in window. I tried changing the resolution of the game but it doesn't change if I set it to low resolution, I cant see anything but can hear the sound.
View 1 Replies
View Related
Dec 27, 2012
I have 135Mbps link speed support ADSL WI-FI router. I have enabled 802.11b+g+n wireless mode and use 20+40 MHz on my router. I use "WAP-PSK" authentication. In addition to that, have a 2.4 & 5 GHz frequency support router and client device.
But my network connection display (WLAN) I have a 54Mbps link speed, why is that? How do I use 135Mbps or at least 100Mbps link speed? Is it a some configuration issue? My Ethernet connection show full speed (100Mbps). (I'm not talking about my internet connection speed).
View 5 Replies
View Related
Feb 11, 2013
Adapter 1: Intel Built-in Lan
Adapter 2: Pci Card
I used to access shared internet from a router, now the router has no internet we only use it for local home sharing. I added the secondary adapter to connect to the DSL-modem directly.so now when I disable the 1st adapter my internet works fine. when they're both enabled internet doesn't work at full speed or sometimes not at all.
View 1 Replies
View Related
Aug 5, 2009
Yesterday I installed RC1 of Windows 7 on my HP 6910p. After install I immediately noticed that the notebook makes much more fan noise then under Windows XP.
The fan seems to be running constantly and whenever I seem to do something a bit graphical it goes at full speed.
Are there any other (HP 6910p) users that have the same experience?
Is there something I can do / tweak to make my notebook quite again.
I have already disabled the superfetch however this only reduces the HDD activity.
View 4 Replies
View Related
Apr 14, 2012
I have a program that measures bandwidth and its reporting that I am downloading at full speed (1.2 mb/s ) all the time, and I think its accurate as my internet feels really slow. I double checked I wasn't downloading anything, and that all of the updates were on idle, but there is still traffic. What should I do? Also, I noticed a ridiculous drop from 250 GB to 217 GB of free space. The free space drop is gone, its showing 250 GB but the bandwidth is still a problem
View 1 Replies
View Related
Jun 13, 2012
So I built a new computer yesterday and when I ran a speed test today I was only getting 9.5mbps when I usually get over 30mbps. It has something to do with this computer since my other computer is getting 30mbps. And yes this computer is connected directly through and ethernet cable.
View 2 Replies
View Related
Feb 20, 2013
recently i noticed this pops up every time i start my pc and im not sure what it ioutedit forgot to mention it usally closes itself about 30 seconds after i start my pc but today it doesn't close itself and i cant end the process if this is in the wrong section im sorry i was a bit worried and just licked windows 7
View 4 Replies
View Related
Jan 21, 2012
When i play COD:4 for a about an hour it will crash to nil power.When i restart it will bsod. Then go through the repair, and eventually restart. My Video Card drivers are up to date. Im stuffedif i know.
Windows 7 Home Premium 64
Original OEM
Hardware Approx 1 year
Install Approx 1 year
Acer Aspire 5742g
[code]....
View 9 Replies
View Related
Jul 15, 2012
I can check Windows 7 64 bit to see what the problem is? I have Opera 12 installed on 2 other computers (one with Windows 7 64 bit and the other w/XP) and the browser opens within seconds. The delay is only happening on the wife's computer. I changed no settings on Opera when I installed the upgrade to 12 so I am guessing it is the PC that is causing the painful delay. I un-installed it twice, installed it once to her SSD and then again on her HDD and there was no change in the startup delay-it is driving me crazy.
View 9 Replies
View Related
Apr 17, 2012
when I forst go on line and click on or try to type it freezes about 30 seconds before it responds?
View 5 Replies
View Related
Jan 29, 2009
Is there a way to make a start up process start with a delay of say 30 seconds via the registry? I tried software but none of them work with win 7 beta.
EDIT: If not, Is there a way to have the start up programs start in a certain order?
View 2 Replies
View Related
Aug 14, 2012
I installed Weathrbug Plus and for some odd reason recently when I run it Windows runs the installation for the program. When I run the prograsm I get the typical "Preparing to install..." abnd then tyhe 'Configuring Weatherbug. I've been in contact with Weatherbug Support all day and we can't seem to find an answer.I'm using Microsoft Security Essentials.This is a clean install of Windows 7. I haven't used any other real-time security software other than MSE.I disabled MSE and tried it and got the same results.
View 6 Replies
View Related
Jan 7, 2012
win 7 home premium on HP pavilion, i do a start ---> search programs and files and it gives me the resultant file but without its path. sometimes thats a fat lot of use! (i've lost the right-click function so cant do quick lookup for properties) what do i have to do to make the search results display the full path of the file? also, if the result shows more than one file and i click on one of them, the result window vanishes so i have to start the search again to find the next file. how do i make the search window stay put until i tell it to go away?
View 5 Replies
View Related