my acer computer stop-ed working while been surfing net, first frozen ,switch it off by pressing power button, then comes message :reboot and select proper boot device, i checked the bios then nor hard drive western segate 1tb neather dvd been detected. i tried to hold f10 but does not work?
so I got a new asus P8z68-V pro motherboard. Im re-using my current 750gb SATA drive. I plugged it into the sata port, and start the computer. When it starts it says "no hard drive is detected!" I go into the bios, and on the bottom it has a disk drive, and a SATA drive. It recognizes that the sata drive is there, but when i go to start up it says no hard drive is detected. I have tried a few different sata ports and it is the exact same thing.
I've got an issue during post installation. One of my hard drive is never given a drive letter, but it does show up as a possible install drive during setup.
I always have to go into Drive Management and assign that drive a letter (and moving my DVD drive down a letter to keep the letters in order).
Under Drive Management the drive has the Properties (System, Active, Primary Partition), so I'm wondering if that is the issue.
Is there a way to change Drive Properties (if that is the case)?
having an issue with a brand new HD I bought. Right now Windows 7 will not detect the HD as a drive.It shows up in the BIOS correctly, but not in My Computer. It is in a Frankenstein setup: SATA connection into the SATA port on the MB (it is enabled and showing), with power from an external HD enclosure.I don't think that would affect it though, as it is just drawing power from a different PS.i did some digging and found it in the System Information under 'discs' instead of 'drives' like my original HD.[URL]...
for some reason my internal hard drive after installing it and reinstalling windows 7 it does not show up for some reason... I have check the cords to make sure they are in correctly
My Boot menu says it's there but my OS does not see it?
I have a sata to esata adapter installed on my desktop but its not spinning up or working my hard drive. The hard drive has 3 ports
Usb to usb Usb to dc power Esata to esata
Over usb it works fine but when i use the esata and power cable the hard drive makes a constant ticking noise and isnt detected on windows. Ive double checked inside my motherboard that its plugged into my sata ll port not sata lll. It isnt detected at all by the computer even when i search for new hardware.
I have an 1T external drive plugged into esata port. It used to work and now it doesn't? When I boot up bios correctly identifies the drive as a seagate sata drive. When I look at device manager is says its a seagate SCSI drive and therefore the system doesn't recognize it at all? In device manager under drive properties it say " this device is working properly" I checked in disk management.
150gb eagle usb drive is not getting detected on my desktop or my laptop , i even tried a friends pc didnt work..
what happened was when i was moving files from my portable hdd to my desktop one of the files (8.5gb) was unable to move.. so i skipped it. anyways i was seeing that 10 mins later that the copying "bar" was not moving at all therefore i pressed cancel to stop the operation. seeing after 15mins later it was just frozen i opened task manager and ended it. then plugged it out. no it just doesn't seem to show up at all. I only see the light on the hdd.
I am trying to install windows 7 for a friend but the hard drive isn't detected within windows setup or within the bios. I have tried installing SATA drivers to try and get windows to recognise the hard drive but to no avail. Is there anything else I can try before assuming that the hard drive may be faulty?
My hard drive, a WD Scorpio 200GB, is not being detected in bios. AHCI mode is enabled. When I go into the Advanced BIOS Features, all the master and slave configs are none; however, my SSD is recognized as I am on my computer right now using it. I tried every SATA Port, EVEN THE SATA PORT MY SSD IS INSTALLED ON, and it doesn't work; I tried 2 different cables and still no recognition; I tried 4 different hard drives and still no recognition, so it is not a problem with my motherboard, hard drives, or cables. What should I do? I have been trying to figure this out for 4 hours.
I recently purchased an Iomega 1TB external hard drive to back up my files from my Laptop (Toshiba satellite) because it has been constantly showing hard drive failure warnings and messages telling me to back up my files. When I connected the hard drive the first time, it worked fine and I was able to access it, but didn't use it for anything at the time. The next time I used it, however, the usual "New device" sound didn't play and the hard drive didn't show up in the file browser. I then looked up the issue to find that it is a common problem where the device hasn't been assigned a drive letter. I went to the Disk Manager to fix the issue but the device was not in the list of connected devices.The problem seems to be with my computer because it works fine on my brother's computer and has no issues.Additionally, I have been having problems with Windows Update being stuck on "Downloading 0%" and have had to use the system restore several times when getting stuck on an update message on startup. I think that this may be the cause of the problem (and yes, I have turned on the hard drive).
my 80GB WD Passport is not being detected by my laptop when plugged in (by USB). A LED at the side of the external hard drive indicates that it is being powered on even though the computer shows no sign of detection (no sound indication; nothing showing up in My Computer). External Hard Drive Specs 80GB Wd Passport, model wd1200u017-002.It is only compatible with USB 2.0.
Computer Specs Windows edition: Windows 7 Home Premium Manufacturer: Dell Model: N5110 Processor: Intel(R) Core(TM) i3-2310M CPU2.10GHz 2.10 GHz Installed memory (RAM): 6.00 GB System type: 64-bit Operating System
(note this computer has both USB 2.0 and 3.0 ports, & I tried the harddrive in both ports)
I have windows 7 32 bit on a toshiba laptop. I am posting becuase this is a strange situation. I have a goflex exteral terrabyte. The computer recognizes it, lists it in the device manager and claims that it is working properly. However, I can't access it, I can't save anything to it, or get anything from it, or even see the files on it.
Now, I have a mac and a pc, the drive said it could be used on both. So i first used it on the mac (and it works perfectly) but not on the pc. It there a share error maybe?
I am an editor and I was hoping to be able to easily move from my computer (mac) to my clients (pc).
My friend's laptop (Acer Aspire One 722 - Windows 7 x64) has been shut down after opening an email and Windows never started up again. When you attempt to start up the windows, it stays the black screen and says "No bootable Device Found"! I inserted Windows Live Disk and loaded it (Windows XP Mini - Golden Edition). When I went to "My Computer", it did not show any local drive. I went to "Disk Management" and in there, there was also no unallocated or allocated space. I even removed the HDD and plugged it back in. No thing happened. Then I removed the RAM card and inserted it back. Again, nothing happened! By the way, HDD had movements when laptop was on (I had removed the beneath panel).I inserted Windows 7 Disk to install a fresh Windows 7. But when you get to the part where it asks you to choose the partition to install the operating Sustem, it shows one unallocated drive with 0 (Zero) capacity! The options to Delete and format are disable. Only the option "New" is active and it gives you (0) bite to partition!
already posted about this issue in the Gigabyte section of the forums. Thought I'd post here for some more feedback, since the issue overlaps (admins please feel free to remove this thread if you think it's redundant).
Building my first computer, and I managed to get it running. I got the Windows 7 Home Premium 64-bit ISO off Digital River and made a bootable USB flash drive. Computer powered up, I set it to boot off the USB drive, and install process started. However, when it prompted me to choose which drive to install Windows to, my hard drive did not show up.
I rebooted, set the hard drive to AHCI in the BIOS (native IDE by default), and tried to install the drivers from the Gigabyte website off a flash drive, and still nothing. I also updated the BIOS and tried again in both IDE and AHCI, but still didn't work. I ordered a new hard drive and will try again later, but I'm doubting it's the hard drive (no signs of mechanical failure).
I originally had been running windows XP on my desktop. About a month ago, I bought a new hard drive and installed Windows 7 Ultimate x64 on it. For the last month, I have been able to dual boot between Windows 7 and XP just fine.
When I tried to boot up my machine this morning, my computer no longer boots and have the following message on screen:
"Reboot and Select proper Boot Device or Insert Boot Media in selected Boot device and press a key"
I checked my BIOS and found that only my new hard drive and CD ROM are detected. I imagined that my old hard drive with Windows XP on it finally died. So I disconnected the old drive, but I am still getting the same issue. I have tried changing the boot order. I also tried booting with the Windows 7 setup CD and tried the repair tools. None of them recognizes the Windows 7 installed on my new hard drive. I started command prompt and was still able to see the contents of the new hard drive, with its WINDOWS directory and all my data/installed programs, so I believe the new hard drive still works. Is there anyway for me to fix this without having to reinstall Windows 7 again and lose all the data/programs I have? Does this have something to do with my XP not being bootable anymore?
OS: Windows 7 Ultimate x64 Motherboard: Gigabyte GA-Z77X-UD3H Harddrive: Seagate Barracuda 1TB 7200RPM 64MB SATA 6Gbps
I'm currently using a Windows 7 PC built by a friend of mine, but starting yesterday, its been acting up. The problem is there used to be two hard drives I can access, Drive B and Drive C. When I boot up the computer, BIOS only detects Drive C (if I'm not mistaken), and Disk Managements as well. I realized this when all the programs whose targets are on that drive are all broken on the desktop.So Drive B doesn't show up anywhere at all.
I have a 1 TB Western Digital Caviar Black hard disk. While installing Windows 7, a screen for hard disk partition was asked. I created 4 drives: 200 GB, 200 GB, 200 GB and 400 GB. And then the windows 7 got installed. But now when I log into my PC, I can only see first 3 200 GB drives. Where did my 400 GB drive go? What mistake did I do and how can I recover it back?
i was using win7 ultimate before and last day i tried to install a new win7 and in wich step that i had to choose a drive to install i sow this message "No drives were found. Click Load Driver to provide a mass storage driver for installation." but in the windows that i was using all of the drives was working.and i installed win vista and no messages like this i sow.
ram:4g video: ati radeon hd 5450 cpu:intel pentium 4 cpu 3.00 ghz 3.01ghz
Lots of BSOD, lock ups, hard drive not being detected by bios, is it failing? Let me start by saying my PC is custom built, most parts are only a year old. The oldest parts are the harddrive (about 5 years) and the soundcard (about 7 years). I have never had major problems until now (a year after building it).
It all started with a blue screen. KERNEL_DATA_INPAGE_ERROR Reboot windows and it seems to start up fine, gets to the desktop and locks up.
Reboot windows and I get another blue screen. BAD_SYSTEM_CONFIG_INFO
I try to start windows from the last good configuration. Error. Registry file failure. Cannot load hive file. I try booting from the windows cd and running a chkdsk. Hard drive starts making a buzzing sound. It gets to step 3 of 5 and stops. Failed to transfer logged messages. Status 50. Now the bios rarely even "sees" the drive. When I can get it to boot and see it, any attempt at diagnostics and repairs produces errors, locks up, or fails.
Is this a bad hard drive? I would hate to spend the money on a new one only to find it is a bad mobo or virus. How can I diagnose this? If it is a bad drive I would like to save what juice is left in it and try to recover a few files before it dies. Most of the important data has been backed up but I would like to try and get a few game save files if I can. But its not a disaster if the drive data is not recoverable.
My pc is a stock Asus G53SX-A1, no hardware changes. Yet it says the reason I got a blue screen was due to hardware changes. My computer froze and rebooted during a video game. So I have been experiencing the classic startup repair loop and I tried everything I could find on google without progress. When I try to the option to fix the problem automatically it says it wasn't able to help and tells me the root cause is because there is no hard drive detected, and that if a hard drive is installed it is not responding. I can't detect in command prompt, but somehow I can see contents of it through BIOS so its really odd. When I tried to reinstall windows it says it can't find a hard drive to install on and I need to insert a drivers disk so I can set up the hard drive to continue. So I put in my Asus drivers disk and yet it tells me there's no drivers detected. I looked at the Asus website and all the downloads they have available are the same as on that same drivers disk it said it couldn't find drivers on. So right now my main problem is my pc doesn't detect that I have a hard drive at all even though I do, the same one the pc came with. This laptop has worked fine for almost a year and this issue just came out of nowhere, so any ideas as to why my HD would suddenly disappear in my computers eyes?
I have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
I have a format activity on my laptop. Before formatting, I had two partitions. Now after formatting I am able to locate the other partition via disk management service. but it is not showing under my computer. What should I do?
When i connect a sata hard disk which is loaded with windows 7 as a secondary to another windows 7 system to take the data backup it is not showing the drives but i can see it in the device management in windows 7.
i have 500gb external hard disk n 3 partition in it.. now al 3 disks am not able to open . tried formatting but it gives error msg saying i cant format the disk..tried using command prompt as well but no use .so how can i format the diskd now?
My desktop does not detect and external hard drive that do not come with their own power supply. I have many externals that also plug into the wall and they are working fine; but whenever it is an external without a plug, i.e. the portable ones they are never found.
They do not show up in Computer Management, so it is not because I did not assign a letter to the drive.
I have tried various things, but I don't know what I should be testing for or looking for. These externals all work on other laptops and other desktops perfectly fine so it is not the externals. When they are plugged into my desktop, they light up normally like they should, but the desktop never detects them. I have tried these externals with the different USB cable I have on hand, but nothing seems to work. It doesn't matter which USB port I plug the device in, it still gives me no response.
So, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?