used my Go Pro yesterday and was trying to get some vid off of it(2.39gb worth) and it gets about half way then I get the error. Also Im not sure if this is unrelated but I keep getting a trojan warning from mcafee(I know its not that great but I get it for free soo..) Anyway mcafee says there is 2 trojans on my computer but it cant delete but when I scan with malwarebytes it shows nothing
View 2 Replies
When transferring photos from an SD card to my computer using Nikon File Transfer, I am getting a message that I do not have access. I am signed in as administrator. I have recently installed MYPCBackup and Bitdefender....could one of these be preventing me from doing the transfer?
View 1 Replies View RelatedI can's get past "error code 0x8007045D" while installing Windows 7. I'm working off the CD Disk that was sent to me. Any help?
View 5 Replies View RelatedI have a dell computer on windows 7, I am getting an error code 0X8007045D i also cannot boot my computer to the home screen, it takes me to the system recovery options i did the command chkdsk /f /r but it tells me "windows cannot run disc check on this volume because it is write protected what do i do now?
View 3 Replies View RelatedI am trying a fresh install of win 7 ultimate after installing a new hdd (it is compatable). After a period of time the following error pops up:error code 0x8007045D win 7I am trying to run chkdsk ?:/f on a PC that has windows and is running using an usb connection to the disk that I want to checkMy problem is when I enter cmd mode it automatically only shows C: etc. What I need to do is change the drive letter to check the other hdd connected to the usb e.g e:
View 5 Replies View RelatedI have an HP tx2627cl table notebook (swivel screen), Win 7 Home prem OS, 4GB ram and a Seagate ext HD (75GB free of 279GB) which will not allow me to backup. I get error message 0x8007045D because of "an i/o device error". I can copy files to that external HD (I, but can't use Windows Backup. I did a check disk of I:/ and got no errors. When I click on Backup to I:/, it starts, says it is creating a shadow copy, runs for a couple of minutes (about 5-6%) then I get the above error message. I have switched USP ports, and tried doing a backup from a "clean boot state" with the recommended settings--all to no avail.
View 3 Replies View RelatedI'm having trouble with my hard drive, it's a WD elements 320gb hard drive and when I try to put anything on it or take thing off it it give me this message saying it was unable to do it because of an unexpected error "error 0x8007045D: the request could not be performed because of an I/O device error" I have some important files on this hard drive.
View 1 Replies View Relatedi cant install windows 7 on my new computer, got the hdd from my old laptop, idk how to format it but when i click new in windows 7 cd menu it pops up with error : Failed to create a new partion on the selected unused space :Error: 0x8007045d I have also tried : format c:/ in cmd and diskpart or something like that.
View 1 Replies View RelatedSo I'm not exactily sure when it happened? From the sounds of it, it was when installing the mircrosoft updates sometime last week?? Anywho.. I noticed when trying to run ANY troubleshooter on my Windows 7 (starter, weak I know). Wether it be a network troubleshooter, or the windows update trouble shooter.. any of them I always get one of the following errors: 0x8007045D or 0x800705B4. The further along I got, the more my comp would freeze up, NOT RESPONDING.... 5 minutes to unfreeze each action, then 2 seconds beofre it would freeze up all over again. GRR. So with my own style of troubleshooting.. System Restore... Nope. Didn't fix it. Tried the "FIX-IT" from MS website, as there were known UPDATE issues that sounded similaar.
But it didn't work either. Then saw the recommended CMD, scannow thingy... But no matter how many times I try.. it always freezes at 55% even leaving it on over night. Sigh. I am pretty BLONDE when it comes to computers, anything past standard maintence is far beyond meI have a GATEWAY LT27 Netbook (manf:nov.2011, no warranty) 32bit. NO Disc drive, and it says I have Service Pack 1, I don't know if that has been updated? and that is why I am broken?
i had to reinstall my windows 7 64x dell inspiron 1750 laptop using my windws 7 home premium disc that came with my laptop when i bought it because it was in a constant starup repair loop. the disc worked find until i got to the part where it said "expanding windows files." it was stuck at 0% after a whilr and then a message popped up that said error code:0x8007045D. during the time when it was expanding windows files i could hear my disc running, but after a while it stops.when i tried running the disc again, the error code message didn't pop up, but the expanding windows files was stuck at 0% forever. when i tried turning on my computer without using the disc, it goes directly from the "finding window files" screen to startup repair. it tells me that it can't fix the problem and i click on a link that tells me that the problem is that my boot configuration is corrupt. i have also ried cleaning my disc and it doesn't look like there's any stratches on it.
View 8 Replies View Relatedemachines em350 netbook with windows 7 installed. For some reason it got messesd up and he tried to do a system restore. Since then when you try to boot up its saying input a password to unlock the harddrive which we dont know. After you input wrong code 3 times you get option to continue which takes you to black screen saying no bootable device detected press any key to continue. Next i tried to do clean install with windows 7 from a usb this goes fine untill it asks for missing cd/dvd driver i have found away round this which is to select cancel then when back on install now screen swap the usb to another port and continue. This works so i select terms and so on then get to part where it asks where to install windows now i have formated and made a active partition on the hard drive but when i try to click next i get error code 0x8007045d this is where im stuck.
View 9 Replies View Relatedi've recently decided to reinstall windows 7 64bit because my computer started freezing up occasionally while browsing, playing games or even watching Internet videos... the freezes would pass after a few minutes and the computer would recover and start up/shut down would take a long time as well. so i thought that reinstalling windows might work as i haven't done it in a long while. but i encountered a problem while installing windows 7 64bit, i receive these errors (0x8007045d and later after trying a few things it changed to 0x80070002 both times it stated something about files missing or being corrupt) while on the "extracting windows files" section of the setup.
i've done a clean install every single time and formated my hdd (seagate barracuda 7200.10 320gb) but got an error every single time but at various %'s (once it went up to 70% other times it would get stuck as soon as 5%). i've tried switching ram's, switching dvd drives, disconnecting my gpu but nothing seems to work... has my hdd died? or perhaps my mobo or cpu is acting up? i burned my windows 7 iso's myself via imgburn - i've used the slowest possible burn speed (x2) and did it multiple times but every single dvd gave same error. also i've tried multiple iso's and downloaded them multiple times as well to confirm they didn't get corrupted while downloading.
my specs:
os: formatted hdd right now but previously i used windows 7 64bit
motherboard: intel bearlake g31 (i think, not sure... its such an old mobo)
cpu: intel core 2 duo 3.3ghz
gpu: geforce 9600gt - tried removing but didn't work
ram: ocz 2x2gb 800mhz ddr2 - tried switching to an exact same pair from another computer but it didn't work
hdd: seagate barracuda 7200.10 320gb
dvd-rom: not sure but i tried two different ones, both producing errors
I cannot transfer files to an SDHC mini card when connected to my Windows 7 computer; no problem on my Windows Vista computer. I've tried changing the drive letter because the drive shows "unallocated", but that didn't work. The drive is showing up in My Computer. I get an error message, "Cannot read from source file". I've selected to give administrator options and everything I know to do to no avail.
View 4 Replies View RelatedToday I decide to make a clean install of Windows.Boot from DVD and try to install ... when goes to 25 - 50% give me this error: 0x8007045DTelling me that are broken files (whatever). I try with a different DVD but the result is the same.I need to work and I can't install Windows.
View 8 Replies View RelatedHave a micro SD card. I keep getting memory card read error. I have many pic's on there I still want. There has got to be some type of program out there to retrieve them with this error.
View 4 Replies View RelatedI am getting a playbackmessage on my HTPC in WMC saying:
"Video playback is not currently allowed. This is often due to incorrect drivers for your graphics card, because the card has less than 64MB of memory or because the card id not DirectX 9 compatible."
I am using a Saphire Radeon HG6750. Which should be more than fine. And the onboard card on my Motherboard should also be fine.
Everything was working fine. I have been fiddling with my display options as I have my HTPC feeding three 1080p TVs via a Gefen HDMI switch. Finally got it so that all three TVs are displaying at 1080p and then my playback errors start.
[As a side note, I have been noticing that when I remote in via a laptop that I get AMD error messages. I think this is regarding my onboard card. When you remote in, the HG6750 does not show up in the Tray. It defaults to the onboard card]
How to I check to see:
1) What graphic card is acutally running?
2) Whether there are problems with the drivers
Code: Windows 7 Ultimate
- x86 (32-bit)
- full retail version
- age of system (hardware): 3+ years old
- age of OS installation: about 1 or 2 months old
- tv tuner card: Tech-Com SSD TV 670 TV Tuner Card
- tv tuning softwarte: honestech TVR 2.5 I am getting Bluescreen error while watching TV for about 20-30 mins. Attached the support dump files.
recently installed windows 7 ultimate x32.when i install graphic card drivers i get "display kernel driver stopped responding and has been succesfully recovered" and i get TDR errors.i can play games with default driver that windows installed but games are laggy and crashes after 30 minutes if i play on higher graphic,i can only play on low graphics and i cant play minecraft cause it requires graphic card drivers .i have nvidia geforce 9600 gt and i can usually play games at medium to high graphic and older games at high but now without drivers i can only play on low graphic,and when i install drivers i get errors .only driver that worked for me is 306 beta but when i install that driver i get TDR error
View 2 Replies View RelatedI'm running Windows 7 Enterprise 64-bit edition, not the Beta or RC. I have 3 video cards in my possession (listed below).
- (PCIe) Evga GTX260
- (PCI) Evga 9400GT
- (PCI) Evga Fx5500
Out of those 3 cards I only use the GTX260 and the 9400GT. I had to 'retire' the Fx5500 because the latest WHQL (certified) drivers only provide support as far down as the "6 series" Nvidia cards. Unfortunately the Fx5500 is a "5 series" and falls below that line. I have already tried to use the GTX260 and Fx5500 in previous versions of Windows (XP and Vista), but there is no way to download and install two separate drivers for two of the same make of video card - you'll get nothing but errors.
There is the option of going to a place like guru3d.com and downloading a custom supported driver that covers both the GTX260 and Fx5500, but the drivers are not certified and lack support. Therefore, I purchased and now use the 9400GT which is covered under the drivers for the GTX260 and eliminates the need for messing around with custom drivers. Also, the 9400GT has a better graphics processor and more memory than the Fx5500, so it was time to upgrade anyway.
I recently upgraded my video card from a 4890 to a 6970. I loaded all the drivers and stuff. Now Aero is off and won't turn back on. When I run the Aero troubleshooter, it results in a "A problem is preventing the troubleshooter from starting" message. The Windows Experience Index is also not working. When I try to run or refresh it, I get a message "Could not measure video playback performance". I tried searching the web, but had no luck.
View 5 Replies View Relatedunlocked mmc by write protection.
View 2 Replies View RelatedI present a dilemma and acquire some assistance with anyone who is tech savvy in computers. Before I describe my problem, I just want to let you know that I have searched for this error and received no solution. But, I believe I have narrowed down what the problem is and I have a strong feeling it has something to do with or revolving around my graphics card(?). I have a report that I saved in my notepad here after the BSOD and it states that it will help describe my problem but I cannot locate it within my computer files(?) (Doesn't show up.)Any game I try to run will crash randomly, even with the settings on low, so I figured it's graphics related(?) I hope anyone can decipher this, it's very confusing and certainly frustrating. I have tried anti-virus scans, registry cleaners, even cleaning out my computer, everything seems to be in place and running fine, the whole nine yards. [code]
View 9 Replies View RelatedI installed a new graphics card (MSI N670 PE 2GD5/OC) and since then my computer has been very unstable and is crashing a lot. The card is factory overclocked and I think it is faulty. Do you know of a way to underclock the card, so I can test if it is the overclock?
PSU: Enermax EMG700AWT
*edit*So I used Afterburner to set my core clock to -104 and my power limit to 72% and this causes my card to boost to about 980MHz. With these settings the crashing has stopped. So the card cannot be used with the factory OC settings. So should I RMA?
i just bought a new video card (EVGA GTX260) yesterday and installed it and played with it with no problem....(one day later)......until now so basically here what happens now. when i boot up it goes through the "starting up" phase and when the window 7 says "Welcome" after that i just get a blue screen, no word no picture just blue!
So i press the reset button and i am only able to go to my desktop menu by safe mode! and if i try to go through "start up computer regular" it would just lead me to the blue plane screen....
The reason why i think it is the driver is because in safe mode i am able to uninstall my nvidia driver. Restart and WOW i am back to my "REGULAR" desktop menu but with no driver. SO as soon as i am on my screen Window 7 wants install the newly detected video card's drivers for me and i do. when i restart BAM! back to the blue screen..
I am having an error with my speakers, it says no audio device is installed, I did directX diagnostic tool test and it says I have no sound card installed...
View 4 Replies View Relatedive recently been having this problem for the last few days i thought i fixed it but it started happening again. not sure whats wrongalso this happen after i installed black ops on my computer off of steam.
View 1 Replies View RelatedIve recently been having this problem for the last few days. I thought I fixed it but it started happening again.
View 1 Replies View RelatedWindows 7 home premium 32bit
zonealarm basic firewall
wlancard dell 1450 usb
Info: the card never had a vista or windows 7 driver. A computer skilled took out a folder from the windows xp installer. Through device manager the folder is installed as driver, and the wlan card works. I wanted to use ubuntu 'remote terminal server'.Connected via pc to pc lan cross over cable. Maybe the connection succeded because ping test was ok. But never made the
program 'remote terminal server' work. At a point zonealarm made trouble, allthough disabled. Shutting down computer worked. Error: Next time I turned on the computer, wlan didn't work. The wlan card makes the connection but there is a yellow triangle on the wifi icon in taskbar. Under network it keeps hanging, messaging 'identifying'.I tried this: Reinstalling zonealarm basic. Reinstalling wlan card folder driver. Didn't work.
My ATI HD3870 video card wont work...Upon downloading the windows 7 ATI CCC it informs me that there has been an error installing the driver...only for it to actually show up in the device manager as working, but then when I try to restart to set my MOBO to use it, I get a BSOD from atikmdag.sys
error code 0x00000116
my Realtek AC'97 on-board audio card was working until reboot just like in another thread on this forum. At this point, however, isn't even showing up on the unknown devices list, nor ANYWHERE else on the Device Manager...
Also there's an unrecognized and unsupported piece of hardware on my mobo (ACPIAWY0001.....WTF is this thing!?) I cant even begin to find drivers that might go to it for Win7x64
can anyone offer fixes for these problems? or should I just go back to vistax32? at least everything worked on there...
I've formatted the laptop and it worked great, but I saw that there was no wireless card and opened it to insert. I put a card from Dell laptop and when I turn on laptop, I got this error:
Error 1802 Unauthorized network card is plugged in - power off and remove the miniPCI network card.
I searched the internet and I saw that for this error, solution is updating/flashing bios with "whitelist removal". I did it and turn on the laptop and it worked normally, until I unplug the charger. Whenever I unplug it from the charger, laptop shut down immediately, just like it is without the battery in it. I tried to get back the original bios, but still the same. It shut down in Windows (7 32bit), in Safe Mode and in Bios. So the laptop is running great when I plug charger, battery shows a 100%. Previously battery held around 2-3h.
about a year ago I had a problem with my pc where I would get the error message "display driver has stopped responding and has successfully recovered" and the occasional BSOD. I solved this problem by simply flashing my bios. However a similar problem has now arrived ( note I have not changed any hardware since the last error) where:
- There is a constant buzzing from my monitor ( NOT a problem with the monitor as it works fine in safe mode with no buzzing, which is why I suspect a gpu problem)
- I get random "display driver has stopped responding and has successfully recovered" messages, but no BSODs. OR the display just goes black and I have to hard reset my pc.
