Driver Detected Controller Error On Device

Jul 20, 2012

Recently I reformatted my HD and clean install win 7 ultimate 32 bit on my computer, bcuz of some problems when booting up, took like forever to boot or 2 to 3 restarts..At first BIOS cant detect my HD so I taught its a hardware issue I did like changing the sata cable also took it to a technician TWICE! maybe the sata port was broken they check all the connection, the last one did fix it but im still having difficulty booting up..He said one last option reformat, so i did reformat it successfully from win xp, now it boots up just fine its running good no problem for like a week yeah just 1 week!. Now my pc has new problem or is it?? Whenever I used it 2 to 3 hours my pc hangs so much even just opening event viewer would take me 5 to 10 mins and 2 errors always flood event viewer the first time i saw it disk error reach 5231 and nvistor32 reach 5366 errors, right now as I am writing this, Disk error reach a waaping 23,145 total. I think this is a serious problem that needs some fixing.

View 6 Replies


ADVERTISEMENT

"The Driver Detected A Controller Error On DeviceHarddisk0DR0"

May 24, 2011

I started having some severe system hang - checked event viewer and found "The driver detected a controller error on DeviceHarddisk0DR0" many times over. I have an EVGA 680i SLI (122-CK-NF68) - updated chipset/storage drivers - no fix. I opted to reload Windows. Previously I had two stand-alone HDDs - I setup a Raid 0 and cleared the MBR before starting the new install."Expanding Windows Files" seemed to take much longer than usual and during the final phase of setup I got "Windows could not configure one or more system components". I repartitioned and formatted and tried again - this time after the initial reboot just as its attempting to load Windows to finish installation (before the point I got the above error) there was an error (too fast to see) and the system reboot itself and continued this cycle till I shut it off. I've had this machine for about 4 years and reload Windows about every 6-8 months. The above two errors back to back seemed like more than coincidence.

View 2 Replies View Related

"The Driver Detected A Controller Error On DeviceIdeIdePort0"

Oct 24, 2012

Recently built a new studio (recording) rig...with the following parts:

CPU: Intel Core�i7 3770K Motherboard: ASUS P8Z77-V Graphics: PNY Quadro FX380 Network: Intel 82579 Gigabit Ethernet Audio: RME HDSPe Multiface II Memory: 16 GB Kingston HyperX Genesis DDR3-1600MHz w/ Intel XMP Optical Drive: Asus DRW-24B1ST 24x DVD-RW Drive HD1: Crucial M4 2.5in SATA III Solid State Drive, 128GB HD2: Seagate 500GB Barracuda 7200.12 HD3: Seagate 1TB Barracuda 7200.12 Case: Coolermaster CM 690 II Advanced PSU: Corsair HX 650 Professional Series OS: Windows 7 Professional 64 Bit SP1 Yesterday (and then again today) I used the DVD drive (basically for it's firs real usage) to rip a few CDs. I ripped a couple with no issues...but then suddenly - after about the third or 4th rip - I would merely reach down, press the Eject button on the drive and the machine would instantly shutdown. No blue screen, no message, no nothing.

At first I thought it was static or something - just reaching over to the machine and pressing the button Event viewer says nothing. However I did see one obscure message back on Oct 7th that stated this:"The driver detected a controller error on DeviceIdeIdePort0"Gotta think that's this DVD drive port. But no other messages at all since then.Anyone got ANY ideas as to what the heck is going on? It's a SATA drive - maybe a cable? Maybe the drive controller is actually FUBAR-ed? Maybe the power supply? Motherboard (I hope not)

View 2 Replies View Related

Realtek Ethernet Controller Not Detected - Deep Sleep Error

Aug 4, 2010

I did a fresh Windows 7 64 bit installation and everything was going fine (besides the BSOD problems about the graphics card which I fixed by renaming nvlddmkm.sys which was the cause of the BSOD) until I tried installing the Ethernet drivers.

Specs:
Gigabyte GA-MA69G-S3H Motherboard
AMD Athlon 64 6000+ CPU
4GB 800 DDR2 Memory
585 Watt Power supply
XFX 8800 GTS GPU
2 Seagate Hard drives : 250 GB & 160GB

Windows doesn't even detect the adapter even though its onboard. I've tried installing the drivers from the original dvd (and in compatible and as administrator) with no luck. I also tried downloading the latest lan drivers from [URL] but it still didn't work. I got a deep sleep error or something. (Which I couldn't resolve cause there's nothing in network connections, not even the 1394 connection which is also turned on in the bios)

No it does not show in device manager under Network adapters. Actually there isn't even a network adapter subcategory unless I click show hidden devices(which has multiple devices then but no network controller). The only driver with a question mark is the graphics card driver which I will try to install after I get the Ethernet adapter working. Microsoft did say its 64 bit compatible [URL] so I don't know what to do. I did check the settings in the bios to see if everything with network was enabled and whatnot.. I also tried resetting everything in the bios to default settings with no luck.

Out of desperation tried adding the device manually through device manager (action>add Legacy hardware>manually>network adapters>have disk..) I tried this with the latest drivers I got from gigabytes website but it didn't even show a device, so I tried the original drivers from the mobo dvd which gave 3 devices.. I tried them all.. each time reinstalling the latest drivers and whatnot to no avail. I'm Thinking of trying to use the windows 64 bit repair disk seeing as it might be software related seeing as it doesn't even show the firewire adapter.

View 14 Replies View Related

An Error Was Detected On Device

Nov 30, 2009

Every time im exploring my fone's memory card,or any other kind of storage like usb memory sticks, the window explorer closes down, and i have to open it agin,locate the folder i was on,but then it will happen again.

If i check Event viewer (System bit)it generates the following event: An error was detected on device DeviceHarddisk2DR2 during a paging operation.

Is my hard drive working ok?+ i noticed that my computer works slow,when im on windows explorer,going to my music,etc...

any help?

View 3 Replies View Related

PCI Device Driver & PCI Simple Communication Controller?

Oct 28, 2012

I have downloaded all drivers for my new HP1000-1136TU lap top. what are these two drivers for and how do I find them?PCI Device Driver & PCI Simple Communication Controller?

View 2 Replies View Related

Get Network Controller Driver And Pci Device Driver?

Sep 16, 2012

want network controller driver and pci device driver.i have hp,amd laptop and use windows 7 32 bit?

View 1 Replies View Related

How To Fix Multimedia Audio Controller & Pci Input Device Driver

Dec 29, 2011

[code] The main problem is the multimedia audio controller & pci input device in the device manager always have a sign of (!) and when I check the properties, it's said code 28(If i'm not mistaken). I have installed the driver from the manufacturer, but still the sound won't come out.

View 4 Replies View Related

USB Controller And Universal Serial Bus Driver Errors In Device Manager

Jul 12, 2012

I recently purchased a Logitech USB headset, and it worked fine for the first few days I had it. I noticed, however, about two days after the purchase that it failed to work. My USB mouse worked fine, however, so I figured it was the headset. I discarded the headset and continued using the built-in microphone. Later, however, when I had to restart my system in order to install an update, my mouse stopped working as well (they work fine on other computers). I looked to see what the problem was in the Device Manager, and my Universal Serial Bus driver was apparently damaged.

As well as my Standard Enhanced PCI to USB Host Controller and my Standard OpenHCD USB Host Controller. I attempted to uninstall, reboot my system, and then let Windows automatically reinstall the drivers, but they always fail to do so in the middle of the installation process. I then attempted to do a system restore the day before both the Windows update and then before the problems with the USB headset, but the problem persisted. If all else fails, I might have to reformat, but I do not want to have to result to that extreme since I cannot salvage anything of value onto an external hard drive.

The PCI to USB Controller has the error: Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)

The OpenHCD USB controller has the error: Windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damaged. (Code 19)

The Universal Serial Bus USB Controller has the error: The Drivers for this device are not installed (Code 28). The system cannot find the file specified. To find a driver for this device, click Update Driver.

I currently run on an HP Pavilion dv7 Notebook PC and run Windows 7 Home Premium Service Pack 1 (64-bit)...

View 4 Replies View Related

No Usb Mass Storage Device Detected In Device Manager?

Nov 4, 2012

what will i do, there is no usb mass storage device driver detected in the device manager of my laptop.

View 3 Replies View Related

Universal Serial Bus (USB) Controller Driver - Error 28

Jan 15, 2011

I mave managed to get USB Storage Devices to work, but things like usb printers are not working. The problems will be described in the following images. The Devices give the error 28 (no driver). Here are some pics- [URL]. I cant find any such driver. No system restore

View 6 Replies View Related

Standard Enhanced PCI To Usb Host Controller Driver Error?

May 4, 2011

i started my pc 2day 2 find thay some of my usb devices hav stopped workin and an error msg in device manager. the error is on the standard enhanced PCI to USB HOst controller. my mobo is a asus m4n68t m le v2 Windows 7 x64

EDIT: I uninstalled the driver n rebooted. windows reinstalled the driver n all seems ok so far

View 2 Replies View Related

No Boot Device Detected?

Mar 9, 2011

whenever my computer restarts it gives me a message that says 'no boot sector on internal hard drive' then after a second a message pops up that says something a long the lines of 'press r1 to try reboot', etc ..everytime I hit f1 the computer will load up windows 7 fine though. But for some reason every single time I restart if gives me that 'no boot sector on internal hard drive' message

View 2 Replies View Related

No Bluetooth Device Was Detected

May 31, 2012

i installed driver hp and successfully install driver.HP ProBook 4530s Notebook PC*-* Download drivers and software - HP Business Support Center.But still in device manager not installed and when try for Bluetooth software. it show this message: no bluetooth device was detected. please make sure that your bluetooth device is plugged

View 1 Replies View Related

No Network Device Detected?

Feb 25, 2011

So I put together a new system today with the following specs. Nothing is overclocked yet as I have yet to recieve the aftermarket CPU cooler.

New Stuff
CPU - Intel 2500k
MB - Asrock P67 Ext 4
Ram - GSkill Ripjaw 1600 Cas9
Vid - 2x MSI GTX570 in SLI
DVD - Samsung DVD Burner

[Code]...

I installed Win7 Pro no hastles and updated it. Installed all the latest drivers etc.Left the PC while it was downloading something and came back to find the Network connection had disappeared. Restarted several times between loading on the newest drivers from Realtek. Each time I checked the device manager I was unable to locate the network device options. Each time i tried to re-install the drivers it would give me a message about "The Realtek Network Controller was not found. IF Deep Sleep Mode is enabled Please Plug the Cable". After doing some reading about it I tried removing the RAM and BIOS battery but to no avail. So I tried updating the UEFI from ASROCK, the existing version was 1.3 and I updated to 1.5. After doing that I was no longer able to load into windows. I read further that if windows had been installed with disk setting set to IDE instead of AHCI it would not work. I could not recall If I had enabled AHCI or IDE so I tried every combination I could come up with but no luck. I then tried to re-install windows but after it installs and reboots the pc it goes to the completing installation screen. I have some mouse control for a short period and then it seems to freeze. However the 3 little progress dots on the screen continue to move eternally. I tried rolling the UEFI version back to 1.3 and ran the same process again and the same result.

It's been several hours since i wrote that part. Since then I have managed to get windows 7 to install. The network device was recognised and worked correctly. I immediately disabled sleep mode for the network device. I updated windows and installed all the required drivers again. Then all of a sudden the connection drops again and no network device can be found. I then go and get the PCIe Intel network card from my previous machine which I had bought due to a faulty onboard network device. I disabled the on board LAN device in the UEFI and then shut down. Installed the Intel Network Card and rebooted. Windows does not find it even when I try and add a device.

Only other thing I can think of is to try and install on a regular SATA drive and see if it's some kind of conflict with the SSD.

View 3 Replies View Related

Sound Device Not Being Detected

May 1, 2011

I could really do with some help. Just installed W7 64 but when I come to install drivers it cannot even detect my x-fi SB at all. Thus I cannot install the driver. No sound at all - I am at a loss. Does anyone have a solution? ps I have a ASUS ABN-SLI Nvidia chipset.

View 6 Replies View Related

No Audio Output Device Is Detected

Mar 29, 2011

I have just done a clean install from xp to windows 7 64 bit, everything is working fine except i have no audio, in the right hand of the task bar i am getting no audio output device is detected. If i look on device manager there is a fault on the multimedia audio controller The drivers for this device are not installed. (Code 28)There is no driver selected for the device information set or element.To find a driver for this device, click Update Driver.

View 1 Replies View Related

USB Device Detected Won't Start (code 10)

Nov 1, 2009

I've done a fresh install of Windows 7 yesterday on my desktop PC and I want to use the virtual PC for some USB hardware that doesn't have any x64 drivers.

I can choose the USB devices fine in the virtual machine, they are detected and XP starts the usual hardware install wizard.

However one of my devices gets the yellow exclamation mark in the device manager with a code 10 (device cannot start).

The virtual machine runs XP SP3, my laptop runs XP SP3 as well and there is no problem on there with this hardware. This leads me to believe that it might be a windows 7 Vmachine issue that is causing this.

I've tried removing the hardware and installing it again, but that didn't solve the problem.

Any ideas for a possible solution?

View 9 Replies View Related

Windows 7 Code 28 Driver - Mass Storage Controller Driver - Error Code 28

Jun 13, 2012

i need the driver for windows 7....error code 28.My laptop is a philips x58......please help....the message i get is Mass Storage Controller Driver not installed

View 1 Replies View Related

CD / DVD Device Driver Missing Error

May 17, 2009

I was trying to install Widows 7RC on Sony VAIO CS-14G laptop. I inserted the disc, clicked on Install and got the following error:

[code]....

View 6 Replies View Related

[DEVICE] Intellimouse Explorer For Bluetooth Not Detected?

Aug 19, 2011

I have an Intellimouse Explorer for Bluetooth that is not being detected by windows 7 with service pack1. I am unable to use the additional buttons or scroll wheel. The mouse is connected via microsoft dongle usb bluetooth receiver. The mouse does not connect to the system. The mouse is shows up as a HID-compliant mouse in Device Manager. installed Intellipoint 8.2. Intellipoint shows "No Microsoft USB Mouse Detected." I have uninstalling the Intellipoint software and reinstalled but not change

View 1 Replies View Related

No Output Device Detected After Installing Windows 7?

Jun 19, 2012

After installing Windows 7, I got the message near de loudspeaker icon "no output device detected" and a red cross.When I go to control panel, sounds, I do not see anything written when I click the play-back button.My PC is a Packard Bell Imedia.The sound worked well until I installed Avast antivirus and Windows updates.

View 7 Replies View Related

Devices Are Not Detected In Device Manager - Windows 7

Jan 6, 2013

I formatted my new Satellite l855, and installed windows 7 instead of windows 8. See what is going in device manager. Screenshot:

Network devices are not detected at all (ethernet, and wireless). My AMD HD Radeon 7670M isn't detected I don't know what's going with those unrecognized devices (yellow) it's a new laptop, i just formatted it and installed windows. What should i do?

Specs:
Toshiba Satellite L855-B511
Windows 7 Enterprise 64bit
Intel (R) i7
AMD Radeon HD 7670M
8GB DDR3

View 2 Replies View Related

Windows 7 USB Device Driver Installation Error

Oct 12, 2012

I recently bought a refurbished Hp m6-1035dx, with OEM windows home premium 64bit.Additionally I also purchased a Samsung 830 SSD and and Optical Bay Caddy. My plan is to install the SSD in the Main Drive Bay and tranfer the current stock hitachi HDD into the Optic Bay. I was considering cloning my OS to the SSD, but decided to go for a fresh install of Windows 7 instead, considering my current OS files take up 40gb (which seems like a lot to me). So considering I have an OEM Windows 7 I opted to try the USB installation, using the guide provided on this forum. Everything was going well until I received the Device Driver error message "A required CD/DVD device driver is missing...etc" which is followed by the option to browse for the device driver. I have read numerous forums on this issue and none of the solutions have worked for me. For example I have tried switching the USB ports, I have actually tried all my USB ports, with no success. Some forums suggest I load the SATA/RAID drivers into my USB and then select those through the browse option. I have no tried this yet, as I have thus far been unsuccessful in locating these drivers. My next move was to burn the ISO onto a disc instead.

View 9 Replies View Related

Audio Works In Ubuntu But Not Windows 7 (Device Not Detected)?

Jan 4, 2012

I have a Lenovo Thinkcentre M55 8813-a21 (LKRYA75). The sound works just fine in any Ubuntu installation i do, but I cannot get sound in either XP or Windows 7. I also couldn't get the networking drivers to work in XP so I am now on Windows 7. I have tried the driver download page on the Lenovo website, but none of them work. I don't know where to go from here.

View 3 Replies View Related

No Boot Device Detected, But Hard Drive Still Works

Jan 10, 2013

I originally had been running windows XP on my desktop. About a month ago, I bought a new hard drive and installed Windows 7 Ultimate x64 on it. For the last month, I have been able to dual boot between Windows 7 and XP just fine.

When I tried to boot up my machine this morning, my computer no longer boots and have the following message on screen:


"Reboot and Select proper Boot Device or Insert Boot Media in selected Boot device and press a key"

I checked my BIOS and found that only my new hard drive and CD ROM are detected. I imagined that my old hard drive with Windows XP on it finally died. So I disconnected the old drive, but I am still getting the same issue. I have tried changing the boot order. I also tried booting with the Windows 7 setup CD and tried the repair tools. None of them recognizes the Windows 7 installed on my new hard drive. I started command prompt and was still able to see the contents of the new hard drive, with its WINDOWS directory and all my data/installed programs, so I believe the new hard drive still works. Is there anyway for me to fix this without having to reinstall Windows 7 again and lose all the data/programs I have? Does this have something to do with my XP not being bootable anymore?

OS: Windows 7 Ultimate x64
Motherboard: Gigabyte GA-Z77X-UD3H
Harddrive: Seagate Barracuda 1TB 7200RPM 64MB SATA 6Gbps

View 1 Replies View Related

Acer Travelmate 5760 Fingerprint Device Not Detected?

Dec 6, 2011

I just bought a new acer travelmate 5760-2434G64M laptop with windows 7 ultimate x64.Everything is perfect except the control panel harware and device doesnot show fingerprint device. also the Bio-protection software cannot detect the device.Device manager shows driver for Secure biometrics devices (EgisTec ES603).It shows the driver is up to date and working properly.I have tried installing the driver form the DVD provided and also from Acer website.

View 3 Replies View Related

No Audio Device Installed In Windows 7 - Hardware Not Detected

Nov 4, 2012

I don't have any sound in my pc, there's a red cross on the volume symbol that says "No audio device installed", in device manager it doesnt appear any audio devices, I already downloaded the latest drivers from Asus but when I run it it says "No hardware detected", i already saw some threads in here with the same problem but couldnt find a solution. My motherboard is a Asus MAximus Formula and the audio is a Supreme FX II. I already tried to upgrade windows 7 with no results.

View 1 Replies View Related

HP Mouse Touchpad Device Driver - Error Code 24

Jan 8, 2013

I have an HP-dm4 2070us and the touchpad will not work. When I go to hidden devices and the driver( Alps) for it is flagged that its not working properly and has an error code 24 for not working or present. I updated the driver and bios (and before that tried rolling back the bios. I even go to Update Driver and it says it's updated and no issues, but then when I exit back out to the main list the error code is still there and it doesn't work. I have to use tab as I don't actually have a mouse. I am on a different computer now. Another HP that I can't get the wireless printer to work on (which is an HP - a gift, otherwise I at this point would not have purchased another HP product).

View 1 Replies View Related

Error: Device Driver Software Was Not Successfully Installed

Jan 28, 2013

Most times when I start my machine or just turn on my monitors (the Windows Display setting is set to turn off at 20 minutes, sleep is set to Never), I find that Windows is installing software. Sometimes it's successful, sometimes it fails.I see others have had this issue, but the offered remedies (reinstall drivers) did not work (I consider I may not have done it properly).? How can I get Windows to install the software correctly and then stop attempting to re-install the software?(Below is the text of the message I get.)

[Window Title]
Driver Software Installation
[Main Instruction]
Device driver software was not successfully installed
Please consult with your device manufacturer for assistance getting this device installed.
Bluetooth Hands-free Audio
Bluetooth L2CAP Interface
Bluetooth Remote Control

View 9 Replies View Related

Windows 7 Install Error Cd.dvd Device Driver Is Missing?

Oct 20, 2012

whenever i try to install windows 7 from my usb it says cd/dvd device driver is missing after i click install now. how do i fix this? ive tried to mount the iso onto usb with different softwares and i redownloaded the iso in case the previous iso was corrupt wat else can i do?

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved