Change Of Mobo And Re-installing Windows 7
Feb 24, 2012If I bought a new mobo and did a clean re-install of my current OEM 64bit Windows 7,do I need to get a new license or can I just activate it online??
View 6 RepliesIf I bought a new mobo and did a clean re-install of my current OEM 64bit Windows 7,do I need to get a new license or can I just activate it online??
View 6 RepliesComputer will not sleep after installing a new mobo. It starts initiating sleep mode and the fans and such shut off and the screen goes blank but after a second the fans and everything come back on but the screen stays blank and the only way to get it out of this state is to hold the power button until it shuts off. I checked the BIOS and did not see anything related to sleep mode. Where would a setting for this be located?
View 4 Replies View Relatedwhy I can't increase the CPU voltage beyond 1.346000 V on my MSI 990xa-gd55 motherboard? I've tinkered with practically everything in the BIOS
View 9 Replies View RelatedI followed an internet guide to put the windows 7 RC installation on a USB drive. I just want to know if I need to put a higher version of the RC onto the drive, do I have to start the entire process over (formatting, partition, copy boot sector etc) or can I just copy the new files to replace the old ones?
View 2 Replies View RelatedOEM pc MOBO died, replaced MOBO, windows having trouble booting (expected). attempting repair with no results but FAIL. I am noobish, so I ask, what can I use to help the repair process? PS: I upgraded my OS out of the box From win 7 home premium OEM install, to Windows 7 Ultimate x64 via disk. I also have win 7 premium (full) on disk from another PC i installed it too. I would do a clean install, but I can't lose any of my photos and data.
View 2 Replies View RelatedToday I built my new rig (specs below) and I kept the hard drive off my old gateway to save some coin. After I installed all the new hardware I turned it on and the ASrock screen popped up and prompted me to choose instant flash, select boot order, enter BIOS, and switch screen. When windows 7 attempts to load it stops while the dots are floating towards the center. The windows repair tool didn't help what-so-ever (go figure >.> ) and the PC won't/can't run in safe mode. I updated the BIOS from the ASrock website but that didn't help. I've tried all of the options provided and none worked. I don't want to format my drive and lose my data but I will if I must because I may have access to a new copy of Windows 7.
Corsair cx500
WD green 1TB
Sapphire 7950 3gb
Cooler master elite 430 mid case
ASrock 770iCafe ATX motherboard
AMD FX 6100
Basic RAM (6GB) (x2 2GB, x2 1GB)
Hyper 212 evo
I've replaced much of my PC's hardware, mobo/CPU/memory and I want the existing Windows 7 HHD to boot. What's the method? I can't even figure how to install the new mobo drivers without a booted OS.
View 14 Replies View RelatedWorking on my computer wants to switch out motherboards and see if it could be done without having to reinstall windows 7. Is it possible? Switching from an MSI X58 Platinum SLI to an Asus X58 Sabertooth.
View 9 Replies View RelatedIntel Core i7 3.4 2nd. Gen. Motherboard: Asus P8P67 PRO RAM: 4GB Video: nvidia 9500 GT Audio Card: Omega STriker 7.1 Windows 7 32bits ultimate.However when i install a windows update the sound cracks for a few seconds, why this happens? i mean the processor is fast enough, why the bus still collapses?
View 1 Replies View RelatedRecently rma'd both cpu and mobo and waiting on the return.Someone at my place of work mentioned that sometimes win7 doesnt like when you change your hardware configurations, like as in,it wont want to boot etc etcBottom line,i did a new build about a month ago,and returned both the mobo AND cpu for the exact same models of each.
View 5 Replies View RelatedI am having to install a new hard drive on a friend's computer. The thing is though, he doesn't have the install disc or even the sticker with his Vista code on it. So I wanted to know if it is possible to install a copy of Windows 7 OEM onto the new hard drive (nothing else in the computer has changed--same mobo, RAM, etc). Is this possible or will the mobo have issues with a new Windows OEM?
View 3 Replies View RelatedI'm trying to install windows 7 again after getting a new Mobo, CPU, and RAM. I'm using a HDD that already has windows on it, but I have to fresh install again. The problem is, whenever I use any kind of W7 disc, it loads the files, gets to the "starting windows" screen, and then re-boots.
Relevant info:
Core i5 2300
AsRock z68 Extreme4 Gen3
2x4GB Patriot Viper 3 1600mhz
WD Caviar blue HDD
Acer OEM DVD player
What I've tried:
New DVD player
New DVD
New RAM
IDE/ACHA modes
New HDD
XP disc (It would work actualy)
What could be:
CPU is bad
Mobo is bad
Somethings not set up right
None of the tested RAM is compatible
I upgraded to a new processor, motherboard, and gpu. I insalled all the new hardware and turned it on. Windows 7 won't/can't load and can't repair. I can't lose the data on the HDD because there's some very important stuff on there.
Sapphire 7950 HD
Corsair cx500
AMD FX 6100
Hyper 212 evo
WD 1TB green
6gb RAM
5 120mm fans
Cooler master 430 elite case
The windows 7 Home premium 64-bit currently installed is upgraded from vista. The upgrade key and disk are available as well as in the HD. The current goal is to upgrade from an Q8300 to a i5-2500K, with the appropriate mobo (asus P8P67 M-Pro) and ram (8gb ddr3 g.skill 1333), what are the necessary steps/advice when doing so w/o purchasing a new OS?
View 2 Replies View RelatedI just assembled a PC with the following specs:
-AMD Phenom II X4
- Mobo Gigabyte GA-880GM-USB3
- 4 GB Kingston DDR3
- Good Quality PSU (Cant remember name)
- 500 GB SATA SEAGATE HD
This machine has been a total pain since I started working on it. Basicaly I cant install Windows 7 64 bits any version (no problems with DVD testesd on other machines beffore). But I could instal any 32 version, I guess there is something on the BIOS that i didnt did.
I have an ASUS P5E-VM HDMI mobo and running Windows 7 Professional. The mobo has a VGA and HDMI and dual monitor capabilities. I have my computer monitor on VGA and my TV on HDMI. When I have both monitor and TV connected, I lose the Windows 7 startup animation. It uses the Vista animation instead. When I have just the computer monitor alone, on VGA or HDMI, the Windows 7 animation comes back. How can I make the Windows 7 be used even if both monitor and TV are connected?
View 9 Replies View RelatedI'm having some performance decrease on my new Build. I bought a new motherboard, Hard Drive and CPU Cooler and had to re-install windows to get my new board to work properly. I've noticed that now in League of Legends my frame rate is around 40-70 when I used to have a constant 150+ even in hectic situations where lots of things were going on at one time. I have the latest AMD Drivers, 13.1. I have tried reverting back to 12.10 to see if its the new version that's causing the problem, but its the same. [code]
View 2 Replies View RelatedI have a driver disc for my Asus mobo, do I need to use it now on 64?
View 1 Replies View RelatedI'm looking to upgrade my CPU and Motherboard from what I currently have.I recently purchased a GeForce GTX 680 but I am seeing minimal improvement from my previous GeForce GTX 480, and have come to the conclusion its my CPU holding me back.
Current specs -
OS - Windows 7 Home
CPU - Intel i7 930 @ 2.80GHz
Motherboard - Gigabyte X58A-UD5
I have been told in the past I cannot replace one and not the other due to my CPU/Motherboard being 1366 pin which is no longer in make.
I just got a new mobo and CPU and was wondering if I will need to reinstall windows with this. I have read different things, some said you can just repair others say complete reinstall.
View 2 Replies View Relatedlow computer knowledge person here and I have recently come into a problem after replacing my mobo/processor/gpu from my old computer. After hooking up the computer and booting it up, it hits the mobo screen then quickly goes into the black screen that says that windows 7 can not be started and gives me the two choices of system startup restore and start windows normally.
Starting windows normally unfortunately returns me to the black screen and so I tried out the restore but to no avail it was unable to fix my problem.Also, I was stupid enough to not transfer any files from my hard drive off to a backup.
My two questions are if it's possible for me to put my hard drive in a friends computer and take the files off there and also if there is any way to fix my hard drive after changing motherboards.
I just built my PC (first one, sounded like a good idea at the time) and was told that getting the latest drivers would "fix" this issue. Problem is, I haven't had a PC or really been on the net since 2001, (don't laugh) so.....I don't know how to get the "right" ones. I realize that i've built something waaaayyy over my head/experience level, so now I just want to learn all that I can.
View 6 Replies View RelatedI have an asrock 775dual-VSTA and I recently upgraded to Windows 7 Ultimate, 32bit.
Things seemed fine, but I realized my USB was performing very slowly.
For example, it takes hours and hours just to upload a few albums to my iPod.
I presume it's a motherboard driver problem. Does anyone know of a fix for this? I dont see any Windows 7 drivers from Asrock for this Mobo.
Im *really* hoping I dont have to buy a new one.
Here are some screenshots from my Device Manager. As you can see, USB seems to be fine, but there are those unknown devices that I have no idea what they are. As far as I can tell, everything is working fine except the USB speed so I presume these unknown devices are related?
If device manager is happy that Windows 7 has managed to find drivers for everything automatically, would the team recommend leaving well alone or going for the mobo vendors drivers?
(I ask because all was well until I installed the Asus Windows 7 drivers for my P5Q...)
I have an issue with my system.
- ASUS M4N68T-M LE V2 MoBo
- Processor is AMD phenom II X4 965 Black Edition.
- One Stick of 2Gb memory DDR 3
- ATI Radeon 6870 Sapphire.
If I restart my system (and this happens like out of 100 restarts 97 times) the system would be on the black post screen and say that the CPU is not compatible with my mobo. Then in order to resolve this I have to got to BIOs and turn on all the cpu cores and the unleashing mode under CPU and restart. Then it would reflect that all the **4 cores are active** and then it would work fine. But why does this happen after every restart. I thought it was CMOS battery but the date and time and other BIOS settings are fine.
I know that since during a windows installation, certain libraries are installed specifically for certain types of chipsets/cpu's and that an abrupt hardware change can cause failures. I read on an article somewhere that you can migrate windows without hardware errors if you manage to get windows to operate on a politically correct mode similar safe mode to boot up with minimal functionality before installing the appropriate drivers for the new board.
View 3 Replies View Relatedok, sounds like a stupid question, i know, but if i purchase them by ende of tomarrow i get 25% off, and i plan on upgrading mobo soon. i have been generaly informed on another post that 1600 in 1333 should work, it will just operate at 1333 speed, is it the same with 2133?
View 9 Replies View RelatedI bought a scythe fan for my case to go on the side, i've tried plugging the 3 pin connector into the PWR_FAN(3 pin) and CHASIS_FAN(4 pin), it gets detected in the bios and in speedfan, and various other software to monitor the fans.
Its running at 3,000 RPM which is way to loud for me, i've tried ASUS AI suite, amd overdrive, speedfan ect to try and turn down the RPM but none of them effect it, its going at 100% non stop and wont slow down no matter what, and even in the bios when i selected 'silent' mode it did not budge in speed at all.
Mobo: ASUS M4A87TD EVO AM3 AMD 870 SATA 6Gb/s USB 3.0 ATX AMD Motherboard
Fan: Scythe DFS123812-3000 "ULTRA KAZE" 120 x 38 mm Case Fan
Anything i can do to make this software or bios adjust the fan to the correct speeds? If i bought a hardware fan speed controller would that work? I was looking at something simple like this: Newegg.com - Sunbeam PL-RS-PCI Rheosmart PCI 20W Fan Controller
But i'd rather not buy if my Mobo or some software can adjust the speed for me.
Am planning a new build and the Asus P8Z77-V board is cheaper by $40 than the Asus P8Z77-V Pro but has 8 phase power as opposed to the Pro with 12 phase power.Now I have done a quick Google and there are refs to this but could someone put it in plain / basic wording as there are some refs to CPU power supply, vdroop, and other tech stuff that I don't really understand??I intend running an i5 3570K and have try at over clocking - if that has any relevance for what my query is about.
View 4 Replies View Relatedrecently i bought a new mobo and CPU. now that everything is installed its telling me i have 16GB of ram installed, but only 8GB are usable.... here is my new processor, AMD FX-8350 Vishera 4.0GHz (4.2GHz Turbo) Socket AM3+ 125W Eight-Core Desktop Processor here is the new mobo..ASUS SABERTOOTH 990FX R2.0 AM3+ AMD 990FX SATA 6Gb/s USB 3.0 ATX AMD Motherboard with UEFI BIOS?G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory its the same type of ram i have now.. i'm noticing that on the mobo, unlike my old mobo, the slots are different ----alternating---- colors.. where my old board the colors were paired together.... should i be placing the ram in a certain way?
View 1 Replies View RelatedI have the above mobo, just installed windows 7 64bit. Everything else is fine but I cannot get the sound to work even though when I test or play music I see the bar rise and fall. I have exhausted everything I know to do. I did see the CM6501 thread here but after trying the drivers, it still does not work and when I click the CM6501 icon, it freezes the PC and I have to reboot.
Any ideas?
CM6501 integrated USB soundcard.