Can't Install Windows 7 To SSD Anymore In IDE Or AHCI
Mar 27, 2010
Im tryin to get my 64GB Mtron SSD runnin with Windows 7 but I can't get it to show up in the installation process. It shows just fine in the BIOS, in device manager, in My Computer and in Windows Disk Management, in fact I can even use it as storage but for some reason It will not show up as a disk to install Windows. I have tried as IDE in BIOS and AHCI and in AHCI mode it will not show up in the BIOS at all or anywhere, I can only get it to show in IDE mode. It has been fully formatted and has had Windows 7 on it here recently (had to reformat due to some speed issues). Does anyone know a way I can get Windows put back on, preferably in AHCI mode cause Im stuck with a Thousand dollar drive thats good for storage only
My board is the Gigabyte GA-EP43-UD3L with BIOS F8 which according to their site is the latest one. Processor Q8600 and 4GB of OCZ Flex RAM...
Im installing a new SSD and i wanted to use it as an oppertunity to change everything over to AHCI and wanted to clarify one thing before i went ahead. Im going to change the setting to AHCI in the bios and then install windows 7 on the SSD. Once i get into windows i was going to plug in the old Hard drives. With the old hard drives being used when my computer was on IDE will they be able to be read or will all the data be lost.
I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
Can someone hit me with a link for manually installing the AHCI driver and switching the OS mode for the storage controller.
If I remember right, this is just putting the driver in /sys/drivers, running a script, and making a registry change. Then you reboot, change the motherboard setting, and then install IMSM after the OS comes back up. I don't remember the script, or if it was just a reg edit, etc.
I have found on 4 different boards if I install in AHCI mode, Windows 7 seems to "find" the drivers for running in AHCI/RAID mode at install. If I install in IDE mode, it does not and I have no option to switch to AHCI/RAID if needed. In the past you had to press F6 (or whatever) and install them from a floppy. I think this is no longer the case with Windows 7. Can anyone confirm this. I don't even have a floppy and never will. I will install in AHCI so I have the choice in the future. Is there any down side to doing this and am I right?
Also - I know there is a registry "hack" you can use to boot into AHCI after installing in IDE but why does everyone not install in AHCI so they have the choice? Am I way off here? Are you planning to install in AHCI to have this benefit?
For some reason, Windows 7 will not let me install ANY drivers anymore. The problem gets even stranger... Lets say I have a USB device that already has the drivers installed on one of the USB ports. If I move the device to a new port, Windows will not install the driver on the new USB port even though Windows already has this driver installed on another port. This problem is not limited to any specific device either, it applies to new HD'S, pci devices, and pcie devices. I have even gone so far as to disable all running application, unnecessary services, etc. I am thinking that there is some setting somewhere or maybe a inadvertent registry change...
I have a PC that is all SATA, including the DVD drive. I prefer to set the SATA controller for AHCI for the bit of extra performance. However, build 7000 will not install from the DVD drive set like that. So I changed the SATA controller to IDE and was able to install build 7000. I then manually changed the SATA driver to AHCI, rebooted and changed the SATA controller to match. That works, of course. With build 7057, however, I was able to perform the install with the SATA controller set to AHCI. A nice improvement.
I also noticed two other things. The magical 200MB hidden partition is now 100MB, and I think I saw a speed improvement copying HDD to HDD. At one point I saw 130MB/sec copying back files to the C: drive (new 500GB Hitachi) from the V: drive (year-old 750GB Seagate). This PC has an ancient 3.2 GHz P-4 on a new motherboard.
I've bought à MSI P67-C45 mobo with Intel i5 2400 CPU, and GSKILL 6Gb of RAM, with SATA WD 1To with 64Mb cache.Nothing works, system can't format frm Vista to Seven, 0x8007005x errors... tried every AHCI/IDE/RAID driver and mode After ~10 days of searching all night on forums, I bought an ASUS P8P67 LE Mobo I tried 2 different DVD Drive, internal & USB, at least 6 SATA cables, one SATA6G certified... Tried XP from SP3 to VISTA, SEVEN in 32 & 64... on CD/DVD,USB KEY Nothing works, tried each .inf driver found on cd or on ASUS or MSI website, nothing works...Tomorrow will go to buy a new HDD, but HDD tested under several boot cd, no problems, 0 dead sectors...the only positive was on ASUS when put on MARVEL SATA6 and not on Intel SATA, but same result, once I'v copied 1% before it stopped and error 0x800700...
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
Everytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
Im using one ssd as my boot drive for windows 7 but i dont know which way i should install it. i can either use AHCI or RAID and if i choose RAID i can specify either RST or RSTe. if i install AHCI, should i install intel's rst by loading the driver before installing windows 7 or install the rst driver after? same with RAID, should i install before or after?
Seems my windows will not backup anymore, it did not finish last backup. I tried to start a new one and just keeps giving the same error, last backup did not finish. I am backing up on a spare external usb drive.find the drive no problem. Give me something called error on the windows bit logger??
This happened when I was booting today after turning it of last night after using it successfully since I bought it.The AHCI Drivers are corrupt.Windows won't load, it is stuck on the load screen.Trying to repair windows using the various F8 options doesn't work because they won't load either.Even the recovery partion won't load, it's stuck on the Acer E Recovery screen "please wait" and it is stuck for several hours on this.Now, in BIOS, when I change to IDE mode, it will load the various F8 options like trying to fix windows, but the problem doesn't solve itself. Also, the recovery partion does load, but it only gives me an option to install everything to factory settings, not just reinstall windows. However, Windows 7 won't actually boot on IDE mode, so I can't actually get into Windows 7.Therefore, my AHCI drivers are corrupt while the IDE ones are fine. How do I install fresh AHCI drivers to fix my corrupt ones from a USB stick? I do not have a windows install disk, it is all on the recovery partion/recovery disks
I need to reinstall my Windows 7 Ultimate 32 bit O/S if I wish to use the AHCI setting for SATA disks?I installed the O/S with the BIOS setting for SATA at ATA then changed it in the BIOS after install. Unfortunately, the PC will not boot with it set to AHCI for SATA but changing it back to ATA gets it to boot.I thought that from Vista onwards the SATA setting in the BIOS could be changed after the O/S had been installed, perhaps not ?
Went into the registry, and changed the Start Value of msahci to 0. However, when I enable AHCI in my bios, Windows 7 won't boot. It freezes and then my system restarts.
So I just bought myself a Crucial M4 SSD. And the guy at the store told me to make it run even faster to go into the BIOS and turn the HDDs to AHCI. So after installing Windows and playing around a bit I decided to go to the BIOS and do it. But then when the Windows sunburst comes up it crashes. What gives? I was reading somewhere else that there needs to be a registry change somewhere too?
i secure erased my SSD which was set to IDE, and re-installed windows 7 on the new AHCI setting instead.Now windows takes x2 (twice) as long to BOOT up, with the circle going round and round and round for about 30 seconds (instead of the previous 8-10 seconds in IDE.
I have an Asus Rampage IV Extreme Motherboard and have Windows 7 Installed on a 96gb kingston ssd.
I now bought 2x 256gb Samsung 830s and want to run them in raid. If I set my RAID in bios, I cannot boot into my kingston ssd, it blue screens. If I set it to AHCI I cannot run my ssds in Raid.
I can do a fresh install on the ssds but how do I move my programs and data over? BTW.. I have Norton Ghost 15 which was provided with the Sammy 830s...
I have a Windows 7 Home Premium 64 bit computer which I will call the main PC. An HP LaserJer is directly connected to it, and shows up as the default printer. About a month ago, it stopped responding to print jobs. They show up in the "jobs pending" list, but do not print. If I try to print to that printer from another PC on the network, the document shows up in the pending list, but then says "Error" and will not print either.If I connect the printer to a different PC, it will print. If I try to print to the printer connected to another PC from the main PC, it will not print. The print spooler is running. There are only restore points from the past week or so, and this started happening over a month ago
I've only had my new computer with Windows 7 for just over a week and it won't work anymore. It goes into Startup Repair and says it can't repair this computer automatically. I press "Finish" and then it just restarts again showing the logo of the motherboard on screen and then goes back into Startup Repair again.
I called the shop where I bought it and they said it is possible I was loading too much software on too quickly. It is a computer I use for business so I wasn't loading any rubbish on and I didn't install that much - Office suite, antivirus, modem software, printer driver.
I'm in trouble with my monitor. I have one AOC 511Vwb LCD 15,6" Widescreen. The specs in portuguese:[URL] I've been using it... i don't know... for like 5 months, and it presented a couple of times an issue of not being recognized by my OS.
When it is recognized, i can set his native resolution to 1280x800 60Hz, but now the max resolution that i can get is 1280 x 720 and this resolution is very very weird on my screen.
So i tried to use it on two diferent notebooks, one using Windows 7 and one using Windows Vista and he worked perfectly only on the notebook with Vista.
And guess what, the monitor is "Vista Ready".
This problem happened before and solved by itself, and now passed 2 weeks and nothing to come back the way it should be. And since i've tried basicly everything i'm now "closed mind" and looking for new viewpoints.
I did a clean install of my OEM Windows 7: Home Premium 64-Bit and i don't have the option to change my Windows color anymore, as i did before. I hate the way it's looking now... It's completely horrible.
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimate PSU: LC Power Arkangel 850W
I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally.
I didn't know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the HDD? Anyway, I really want to start using the disk. I have tried installing Windows 7 from a dvd as well as from a USB key.
I changed the appropriate setting in the registry. (msachi > start: 0) Then I changed the setting in my motherboard and Windows froze upon starting up, and my system rebooted.
The thing is, I changed it to AHCI before. It worked fine! I then switched back to IDE while trying to fix a problem with eSATA detection (turned out to be a faulty cord), Now I can't switch back! Sigh. I really would like my eSATA to be plug and play.
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimat PSU: LC Power Arkangel 850W Ok so here's the deal. I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally. I didnt know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the disk? Note: I have tried installing Windows 7 from a dvd as well as from a USB key.
Okay I plan on doing a clean install of Windows 7 on my laptop. I have an SSD from crucial.I know that I need to enable AHCI BEFORE I start the installation of Windows 7...correct? I saw this Intel website in regards to AHCI.Intel Rapid Storage Technology” Configure the BIOS for RAID or AHCI on an Intel Desktop Board.I know that my laptop has a chipset that supports AHCI."Enabling AHCI or RAID after installing the operating system is not recommended or supported when a SATA hard drive is the boot drive. Enabling AHCI or RAID after installing the operating system might cause an immediate blue screen with an 0x0000007b error code, followed by a reboot. If you use AHCI or RAID, enable them before installing the operating system.".it looks like enabling AHCI is the absolute last thing I should do before installing Windows 7. As in this is the routine I should follow.
1) Back up any drivers/files/etc that I need 2) Insert Windows 7 Installation Disc 3) Close out of pop up install window. 4) Restart Laptop 5) As laptop is restarting enter BIOS 6) Follow Intel's step by step guide for enabling AHCI 7) Change system to "Boot from DVD Drive" 8) SAVE new BIOS Settings....EXIT
At that point my computer should REBOOT and this time it will do so from the DVD drive and Windows 7 installation screen will appear correct? OR am I missing something? Do I need to do anything in Windows 7 itself before I do anything with the BIOS?