AHCI : Enable In Windows 7 / Vista
Feb 7, 2010How to Enable AHCI in Windows after Installation ?
View 0 RepliesHow to Enable AHCI in Windows after Installation ?
View 0 RepliesWent into the registry, and changed the Start Value of msahci to 0. However, when I enable AHCI in my bios, Windows 7 won't boot. It freezes and then my system restarts.
View 5 Replies View RelatedOkay I plan on doing a clean install of Windows 7 on my laptop. I have an SSD from crucial.I know that I need to enable AHCI BEFORE I start the installation of Windows 7...correct? I saw this Intel website in regards to AHCI.Intel Rapid Storage Technology” Configure the BIOS for RAID or AHCI on an Intel Desktop Board.I know that my laptop has a chipset that supports AHCI."Enabling AHCI or RAID after installing the operating system is not recommended or supported when a SATA hard drive is the boot drive. Enabling AHCI or RAID after installing the operating system might cause an immediate blue screen with an 0x0000007b error code, followed by a reboot. If you use AHCI or RAID, enable them before installing the operating system.".it looks like enabling AHCI is the absolute last thing I should do before installing Windows 7. As in this is the routine I should follow.
1) Back up any drivers/files/etc that I need
2) Insert Windows 7 Installation Disc
3) Close out of pop up install window.
4) Restart Laptop
5) As laptop is restarting enter BIOS
6) Follow Intel's step by step guide for enabling AHCI
7) Change system to "Boot from DVD Drive"
8) SAVE new BIOS Settings....EXIT
At that point my computer should REBOOT and this time it will do so from the DVD drive and Windows 7 installation screen will appear correct? OR am I missing something? Do I need to do anything in Windows 7 itself before I do anything with the BIOS?
I'm coming from win XP and I've got 3 SATA drives currently operating in IDE mode. I am just about to move to Windows 7 Pro and I was considering setting the motherboard to recognize the drives as AHCI. I am going to reformat one drive completely for the OS drive.
My questions are:
1. Will this negatively affect my other two storage drives because they had previously been running in IDE mode?
2. Is there a way to determine whether or not my drives support AHCI at all? (They're all SATA drives bought in the last 4 years.)
3. I intend to run XP mode, will AHCI mode pose any problems for this?
New i5-8570k with Z77X-D3H build. SSD's & HD's. 1 backup HD is in a caddy (simple SATA connection, its not a raid device) with on/off switch. BIOS is AHCI by default. Installed Win7 Pro x64 then after chipset drivers with mobo DVD. IRST is installed but notes say it should be installed during o/s install. How to confirm AHCI is on? The drives aren't listed in safely remove/eject hardware icon in systray. HD Caddy is useless because hot swap isn't working or on.
Does the new Z77 chipset require the drivers to be installed during O/S install? I tried that with files on USB flash drive but Win7 prevented it because the drivers were unsigned. These are Intel's latest drivers for the Series 7 chipsets. I've tried to confirm whether i have AHCI on or not, 'AS SSD benchmark' detects 'iaStor'. I guess if the chipset drivers must be installed before o/s install then the question becomes "How to install Intel drivers that aren't signed during O/S install". There is no 'ignore & continue' option.
I recently upgraded to an SSD. I moved windows 7 over to the new SSD and re-aligned the partition properly The drive setup is as follows:
2x 500GB WD Black drives in RAID 0
1x 120GB ADATA S510 SSD
In BIOS, RAID mode is enabled. You cannot enable RAID for one pair of drives and AHCI separately. I was assuming disks that are not part of the logical RAID volumes would be set to AHCI automatically. I have enabled NCQ in AMD RaidExpert for the SSD.WEI is 5.9 for the primary disk. The primary disk is the SSD.Other strange behanivour is that the RAID array and the SSD both appear as SCSI devices in device manager, and Windows won't accept the ahci drivers from ECS.
I have the GA-EX58-Extreme Board and have just installed the pre release of Windows 7 7600 64 bit. Normally i have experience to get the BSOD when in staling with AHCI active in bios so i change to IDE mode. Installation went flawless and also the change to AHCI mode on Intel ICH10R controler went normal.
As always i got problem to change the J micron controller to AHCI and of cause i got the BSOD again. I installed the latest R1.17.48.16 driver and tryed again but no luck. Can some tell me what i am doing wrong. ? I have a hardisk and a dvd drive attached to the J micron Sata connection.
anyways, my main drive is a RAID 0 with Vista x64, but I have a second HD that is a SATA 250GB, which I installed Windows 7 on. The only way I could get install to work was to switch my BIOS to IDE mode rather than RAID. I would of course though, like to be able to access my Vista drive from Windows 7 (and more importantly, not have to switch between IDE/RAID mode at all in the BIOS, it's a pain).
Now, the one odd this about this all is that the drivers I have for Vista (x86/x64 drivers) for this mobo's RAID controller WORK when loaded on installation to identify and install to the drive, but seem to not load or not work in any way once the first reboot on install occurs. Maybe this is because I installed from within Vista x64, though.
(Incedentally, my motherboard is an M3A Asus, using ATI's SB600 for a RAID controller)
I've tried loading the drivers from within Windows 7 while in IDE mode, but the install program won't let me. At first it didn't allow because of version restrictions, but then I altered the ini file to get around that, but it encounters some sort of error when installing and quits.
Any help that can be offered, would be grateful. I realise it's a beta and not a real release, so I can get past the BSOD from my odd setup, and I really am enjoying playing around with it so far. Very very impressed.
Edit: Just in case anyone thinks of suggesting me to right-click the inf file and install that way, already tried, won't allow for it.
i am trying to use my headphone but its no sound on it i am trying to enable but no option showing for enable
View 2 Replies View Relatedi am trying to use my headphone but its no sound on it i am trying to enable but no option showing for enable
View 1 Replies View RelatedMy system dual boots to either Windows 7 or Vista Ultimate, or, at least it is supposed to. Something happened and now the system just boots to Winodows 7 without giving me the choice to boot to either. When I use F6 I find that only Windows 7 is listed in the Operating Systems box.
View 1 Replies View RelatedEverytime i want to swap hard disk with different OS, WinXp(IDE) to Windows 7(AHCI), i need to do change some hard disk setting on BIOS. Is there any way that i can do to make both hard disk with different OS compatible on the desktop PC without change any setting on BIOS everytime i change hdd? Is there a way to make WinXP IDE mode to run under AHCI mode?
View 1 Replies View RelatedIm using one ssd as my boot drive for windows 7 but i dont know which way i should install it. i can either use AHCI or RAID and if i choose RAID i can specify either RST or RSTe. if i install AHCI, should i install intel's rst by loading the driver before installing windows 7 or install the rst driver after? same with RAID, should i install before or after?
View 27 Replies View RelatedNew laptop has Windows 7 Home Premium 64bit. I have two business programs that won't run on a 64bit system. Partitioned the hard drive to install Vista Home Premium 32bit to create a dual boot system solely to run these two programs.Can't get Vista to load. Followed tutorial meticulously. All goes fine until the "Vista will boot for the first time" step. After this first boot, the screen returns to the "completing installation" page. However, the process dies here and the progress bar across the bottom of the screen never moves, even after an hour. Reformatted the partition and started over with same results. Multiple attempts always die after the first boot.
View 9 Replies View RelatedIm tryin to get my 64GB Mtron SSD runnin with Windows 7 but I can't get it to show up in the installation process. It shows just fine in the BIOS, in device manager, in My Computer and in Windows Disk Management, in fact I can even use it as storage but for some reason It will not show up as a disk to install Windows. I have tried as IDE in BIOS and AHCI and in AHCI mode it will not show up in the BIOS at all or anywhere, I can only get it to show in IDE mode. It has been fully formatted and has had Windows 7 on it here recently (had to reformat due to some speed issues). Does anyone know a way I can get Windows put back on, preferably in AHCI mode cause Im stuck with a Thousand dollar drive thats good for storage only
My board is the Gigabyte GA-EP43-UD3L with BIOS F8 which according to their site is the latest one. Processor Q8600 and 4GB of OCZ Flex RAM...
This happened when I was booting today after turning it of last night after using it successfully since I bought it.The AHCI Drivers are corrupt.Windows won't load, it is stuck on the load screen.Trying to repair windows using the various F8 options doesn't work because they won't load either.Even the recovery partion won't load, it's stuck on the Acer E Recovery screen "please wait" and it is stuck for several hours on this.Now, in BIOS, when I change to IDE mode, it will load the various F8 options like trying to fix windows, but the problem doesn't solve itself. Also, the recovery partion does load, but it only gives me an option to install everything to factory settings, not just reinstall windows. However, Windows 7 won't actually boot on IDE mode, so I can't actually get into Windows 7.Therefore, my AHCI drivers are corrupt while the IDE ones are fine. How do I install fresh AHCI drivers to fix my corrupt ones from a USB stick? I do not have a windows install disk, it is all on the recovery partion/recovery disks
View 9 Replies View RelatedI need to reinstall my Windows 7 Ultimate 32 bit O/S if I wish to use the AHCI setting for SATA disks?I installed the O/S with the BIOS setting for SATA at ATA then changed it in the BIOS after install. Unfortunately, the PC will not boot with it set to AHCI for SATA but changing it back to ATA gets it to boot.I thought that from Vista onwards the SATA setting in the BIOS could be changed after the O/S had been installed, perhaps not ?
View 1 Replies View RelatedSo I just bought myself a Crucial M4 SSD. And the guy at the store told me to make it run even faster to go into the BIOS and turn the HDDs to AHCI. So after installing Windows and playing around a bit I decided to go to the BIOS and do it. But then when the Windows sunburst comes up it crashes. What gives? I was reading somewhere else that there needs to be a registry change somewhere too?
View 7 Replies View Relatedi secure erased my SSD which was set to IDE, and re-installed windows 7 on the new AHCI setting instead.Now windows takes x2 (twice) as long to BOOT up, with the circle going round and round and round for about 30 seconds (instead of the previous 8-10 seconds in IDE.
View 1 Replies View RelatedI have an Asus Rampage IV Extreme Motherboard and have Windows 7 Installed on a 96gb kingston ssd.
I now bought 2x 256gb Samsung 830s and want to run them in raid. If I set my RAID in bios, I cannot boot into my kingston ssd, it blue screens. If I set it to AHCI I cannot run my ssds in Raid.
I can do a fresh install on the ssds but how do I move my programs and data over? BTW.. I have Norton Ghost 15 which was provided with the Sammy 830s...
I have two drives (C and D) with Vista on one and Win 7 on the other (not sure if they're actual drives or partitions of a single drive, how do I tell?). I am dual booting and never use Vista. Starting to need the disk space and want to delete Vista. Is this difficult in this scenario?
View 2 Replies View RelatedI had recently installed windows 7 on my laptop running windows vista. I did not remove the existing windows vista installation, and thus win 7 was installed in a dual boot combination. Now, i want to remove vista from my laptop and use windows 7 only.The problem is that during installation, win 7 was installed on logical drive and windows vista was on the primary drive. Thus, i cannot delete/format the windows vista partition. Also I cannot transfer the boot drive to the partition containing win 7 because the vista partition is the active one.
View 6 Replies View RelatedFirst thing, my build:
Board: Gigabyte GA-P55A-UD4
CPU: Core i7 870 @ 2,93 Ghz
Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18
Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD
Running: Windows 7 Ultimate
Trying to install: Windows 7 Ultimate
PSU: LC Power Arkangel 850W
I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally.
I didn't know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the HDD? Anyway, I really want to start using the disk. I have tried installing Windows 7 from a dvd as well as from a USB key.
I changed the appropriate setting in the registry. (msachi > start: 0) Then I changed the setting in my motherboard and Windows froze upon starting up, and my system rebooted.
The thing is, I changed it to AHCI before. It worked fine! I then switched back to IDE while trying to fix a problem with eSATA detection (turned out to be a faulty cord), Now I can't switch back! Sigh. I really would like my eSATA to be plug and play.
First thing, my build: Board: Gigabyte GA-P55A-UD4 CPU: Core i7 870 @ 2,93 Ghz Graphic: Sapphire AMD Radeon 8670 Mushkin 2x2Gb Red Culvert Kit @ 1600Mhz CAS 6-7-7-18 Seagate 320 GB SATA II HDD + WD Caviar Black 1TB SATA III HDD Running: Windows 7 Ultimate Trying to install: Windows 7 Ultimat PSU: LC Power Arkangel 850W
Ok so here's the deal. I have Windows 7 Ultimate installed on my 320 Gb HDD and everything is running ok. I just bought a WD Caviar Black 1TB SATA III disk and I want to install Windows 7 there, since the disk is faster. Here's what happens. When I connect the disk (it is connected GSATA 3 connectors), the disk will be recognized in bios and in Windows, but wont show under My Computer. I figured it must be some software bug so I formatted the disk in diskpart (clean format) and installed Windows 7 on it. At that time the GSATA 3 interface was set to IDE mode. It ran fine but after installing a big batch of Windows updates, the system hung at windows startup screen. After restoring the system to a previous state (i.e. before the updates), the system booted up normally. I didnt know what was wrong so I formatted again, and this time I set the GSATA 3 to AHCI mode, since I realized this is a better option. When installing in AHCI mode, the computer expands the windows files but when the system is restarted, I get a BSOD (code Stop 0x000000B4 video driver failed to initialize) at Setup is updating registry settings. I really want to use the AHCI mode, but I cant get the system to work in IDE either so its really a bugger. I have no idea what could be causing this as the system works fine when using the other disk. Can the BSOD be caused by the disk? Note: I have tried installing Windows 7 from a dvd as well as from a USB key.
I have a legitimate copy of Windows Vista with key codes etc and I have a legitimate upgrade disk for Windows 7. I had Windows 7 installed on a previous system build which had a HD crash and now I am starting again from scratch (wiyh backed up data).
Like a dolt, I installed Wondows 7 before I remembered it was an upgrade edition. I've looked all over the MS site and don't see a method I can use to Activate Windows 7 from this point. way to use my legitimate Windows disks and keys without having to wipe the drive, install Vista and then install Windows 7 yet again.
It's aggravating to have legitimate software and not be able to use it without needing to trick the system - surely there is a way to not have to start all over?
Reinstall w7 Upgrade on new Sata III as c: with AHCI support?
View 9 Replies View RelatedI have a SSD with Windows 7 Home Premium x64. To boot off it my bios needs to be in AHCI mode. I also have Windows XP Prof SP2 x84 on a Sata2 drive and too boot off of that I need to be in IDE mode. Also when I boot into the XP drive it rewrites the boot BCD and I need to load up the Windows 7 install disk and do a repair to get back into Windows 7. While EasyBCD will allow me to fix that issue I can't imagine it will allow me to do the whole AHCI/IDE combo will it?
View 3 Replies View RelatedIm installing a new SSD and i wanted to use it as an oppertunity to change everything over to AHCI and wanted to clarify one thing before i went ahead. Im going to change the setting to AHCI in the bios and then install windows 7 on the SSD. Once i get into windows i was going to plug in the old Hard drives. With the old hard drives being used when my computer was on IDE will they be able to be read or will all the data be lost.
View 1 Replies View RelatedAHCI Port Error 0 Press F2 to continue. This error shows on my Gateway zx4800 but when I press F2 nothing happens. S.M.A.R.T capable and status BAD.....it also show this above the AHCI error. My hdd works with other PC.
View 2 Replies View Relatedi'm working with a new pc build that uses a 60 gb ssd for its boot drive, and which is also reusing some "old" sata hdds for storage.
at the time i installed windows 7 ult 64, i had only a new ssd plugged in, and the bios was set to ahci mode. the installation went fine and i was able to boot into windows afterwards without issue.
then, i connected a wd caviar black sata hdd to use as storage, with the ssd being the boot drive. with both of them connected, windows will not get past the starting windows screen.
i made this video of the program before i understood that it was a drive controller issue: startup problem - Internet in it, you can see that windows boots fine in ahci mode with just the ssd plugged in, but that when the backup sata drive is also connected it doesn't get past the starting windows screen.
for the record, this caviar black hdd was my previous boot os, and it also has a windows 7 install on it (which i've renamed the base folder of), but it is not booting from that hdd. also, i have tried the same thing with other "old" sata hdds that do not have any previous windows install on them, and the result is the same thing which is shown in the video.